Model 2600-BAN (2600 Series) SMU Output to Banana Test Lead

Model 2600-BAN (2600 Series) SMU Output to Banana Test Lead
Keithley Instruments, Inc.
28775 Aurora Road
Cleveland, Ohio 44139
(440) 248-0400
www.keithley.com
Model 2600-BAN (2600 Series)
SMU Output to Banana Test Lead/Adapter Cable
Introduction
This document contains information on the Model 2600-BAN SMU Output to Banana Test Lead/Adapter
cable. This cable connects Category I SMU connections on the rear panel of a Model 260x Series
SourceMeter® Instrument to banana test leads.
WARNING Maximum floating (common mode) voltage for a SMU is 250V. Exceeding this level could damage the instrument and create a shock hazard.
Using an external source to float a SMU could create a shock hazard
in the test circuit. A shock hazard exists whenever >42V peak is
present in the test circuit.
NOTE
If applicable, remove terminal block(s) before using the Model 2600-BAN.
The Model 2602 can use two terminal blocks (one for each SMU channel),
and the Model 2601 has one terminal block for the single SMU.
A terminal block can be removed from the rear panel by loosening the two
captive retaining screws and pulling them off the rear panel.
When the Model 2600-BAN is connected to the SMU connection, input/output
LO can be connected to chassis ground by inserting the white banana jack to
the rear panel chassis ground banana jack (Figure 2).
PA-905 Rev. A / 04-05
Cable description
As shown in Figure 1, the cable has a working dimension (dimension less the connectors) of 1.0 meter.
Five color coded safety banana connectors (2 black, 2 red, 1 white) provide multiple test connection
from the SMU output. Table 2 contains pinouts for the cable. As shown in Table 2, Pins 1–4 and Pin 8
are connected to the banana plug through cables.
NOTE
The Model 2600-BAN Cable assembly is not UL approved.
Table 1
Cable specification
Characteristic Specification
Maximum Voltage
300V
Maximum Current
3A
Category
I
Figure 1
Cable features
1.0 M
Black Cable
LO
Black Cable
S LO
White Cable
GUARD
Red Cable
Strain
Relief
HI
Red Cable
SMU Output
Connection
S HI
Table 2
Cable pinouts
Pin No.
1
2
3
4
5
6
7
8
2
Plug
Black
Black
White
Red
Red
Printed
LO
S LO
GUARD
HI
S HI
Figure
87654321
Connection
Refer to Figure 2 for a typical instrument connector location. Refer to the specific instrument’s User’s
Manual for additional connection information.
WARNING Do not exceed the voltage rating for the cable or for the Model 260x.
Make sure connections at both ends do not exceed the rated specifications.
Failure to follow this warning may result in injury from electrical
shock as well as damage to the equipment.
Figure 2
Typical instrument connector
Category I SMU connection
WARNING:NO INTERNAL OPERATOR SERVICABLE PARTS,SERVICE BY QUALIFIED PERSONNEL ONLY.
UL
C
S G
HI
CHANNEL A
US
LISTED
SourceMeter
4ZA4
G G HI G S LO
LO
!
CAT I
CHANNEL B
!
S
CAT I
LO LO G HI G G
!
DIGITAL I/O
LINE FUSE
SLOWBLOW
3.15A, 250V
RS-232
S
G HI
LINE RATING
100-240VAC
50, 60Hz
240VA MAX.
MADE IN
U.S.A.
IEEE-488
(CHANGE IEEE ADDRESS
WITH FRONT PANEL MENU)
!
TSP-Link
R
CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,REPLACE FUSE WITH SAME TYPE AND RATING.
Chassis ground banana jack
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising