Settings and Adjustments 43
3-062-657-11(3)
CD/DVD Player
Operating Instructions
DVP-S350
© 2000 Sony Corporation
WARNING
To prevent fire or shock
hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to qualified
personnel only.
CAUTION
The use of optical instruments with this
product will increase eye hazard. As the
laser beam used in this CD/DVD player is
harmful to eyes, do not attempt to
disassemble the cabinet.
Refer servicing to qualified personnel only.
Welcome!
For customers in the U.S.A
Owner’s Record
The model and serial numbers are
located at the rear of the unit. Record the
serial number in the space provided below.
Refer to them whenever you call upon
your Sony dealer regarding this product.
Model No. DVP-S350
Serial No.______________
CAUTION
You are cautioned that any change or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
NOTE:
This label is located on the Laser protective
housing inside the enclosure.
This symbol is intended to
alert the user to the presence
of uninsulated “dangerous
voltage” within the
product’s enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
CAUTION
TO PREVENT ELECTRIC SHOCK
MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
2
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the
following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
Thank you for purchasing this Sony CD/
DVD Player. Before operating the unit,
please read this manual thoroughly and
retain it for future reference.
TABLE OF CONTENTS
About This Manual 4
This Player Can Play the Following Discs 4
Precautions 6
Notes About the Discs 6
Getting Started 7
Unpacking 7
TV Hookups 8
Receiver (Amplifier) Hookups 10
5.1 Channel Surround Hookups 12
Selecting the Language for the On-Screen
Display 14
Playing Discs 16
Playing Discs 16
Searching for a Particular Point on a Disc 18
Resuming Playback from the Point Where You
Stopped the Disc (Resume Play) 19
Using the DVD’s Menu 20
Playing VIDEO CDs with PBC Functions
(PBC Playback) 21
Using the Front Panel Display 22
Settings and Adjustments 43
Using the Setup Display 43
Setup Display Item List 45
Setting the Display Language or Sound Track
(LANGUAGE SETUP) 46
Settings for the Display (SCREEN SETUP) 47
Custom Settings (CUSTOM SETUP) 48
Settings for the Sound (AUDIO SETUP) 51
Controlling your TV or AV Receiver (Amplifier)
with the Supplied Remote 53
Additional Information 55
Troubleshooting 55
Self-diagnosis function 58
Specifications 59
Glossary 60
Language Code List 62
Index to Parts and Controls 63
Index 66
Using Various Functions with the
Control Menu 24
Using the Control Menu Display 24
Control Menu Item List
26
Searching for a Title/Chapter/Track/Index/
Scene 27
Checking the Playing Time and Remaining
Time 28
Selecting a Starting Point Using the Time Code 28
Viewing the Disc Information 29
Changing the Sound 30
Displaying the Subtitles 32
Changing the Angles 32
Digital Cinema Sound Settings 33
Checking the Play Information 35
Locking Discs (Custom Parental Control) 36
Creating Your Own Program (Program Play) 37
Playing in Random Order (Shuffle Play) 39
Playing Repeatedly (Repeat Play) 40
Repeating a Specific Portion (A-B Repeat) 41
3
About This Manual
Conventions
Icon
• Instructions in this manual describe the controls on the player.
You can also use the controls on the remote if they have the
same or similar names as those on the player.
• The icons on the right are used in this manual:
Meaning
Z
Indicates that you can use only the remote
to do the task.
z
Indicates tips and hints for making the
task easier.
Indicates that the function is for DVD
VIDEOs.
Indicates that the function is for VIDEO
CDs.
Indicates that the function is for Audio
CDs.
This Player Can Play the Following Discs
DVD VIDEOs
VIDEO CDs
Audio CDs
Audio + Video
Audio
Disc logo
Audio + Video
Contents
Disc size
12 cm
8 cm
12 cm
8 cm
12 cm
8 cm
(CD single)
Play time
About 4 h (for
single-sided
DVD)/
about 8 h (for
double-sided
DVD)
About 80 min.
(for
single-sided
DVD)/
about 160 min.
(for
double-sided
DVD)
74 min.
20 min.
74 min.
20 min.
The “DVD VIDEO” logo is a trademark.
This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as PAL or SECAM.
Region code of DVDs you can play on this unit
Your DVD player has a region code printed on the back of the unit and will only play DVDs
that are labeled with identical region codes.
DVDs labeled
ALL
will also play on this unit.
X
Region code
MODEL NO.
DVP–XXXX
CD/DVD PLAYER
AC 00V 00Hz
NO.
00W
SONY CORPORATION
MADE IN JAPAN
0-000-000-00
If you try to play any other DVD, the message “Playback prohibited by area limitations.” will
appear on the TV screen.
Depending on the DVD, no region code indication may be labeled even though playing the DVD is prohibited by area restrictions.
Note on playback operations of DVDs and VIDEO CDs
Some playback operations of DVDs and VIDEO CDs may be intentionally fixed by software producers. Since this player plays DVDs
and VIDEO CDs according to the disc contents the software producers designed, some playback features may not be available. Also
refer to the instructions supplied with the DVDs or VIDEO CDs.
4
Terms for discs
Discs that the player cannot play
• Title
The longest section of a picture or music feature on a DVD, the
movie, etc. in video software, or the name of an album in audio
software.
The player cannot play discs other than the ones listed in the
table on page 4. CD-Rs, CD-ROMs including PHOTO CDs, data
sections in CD-EXTRAs, DVD-ROMs, DVD-audio, HD (high
density) layer of Super Audio CD etc., cannot be played.
• Chapter
Sections of a picture or a music feature that are smaller than
titles. A title is composed of several chapters. Each chapter is
assigned a chapter number enabling you to locate the chapter
you want. Depending on the disc, no chapters may be
recorded.
• Track
Sections of a picture or a music feature on a VIDEO CD or a
CD. Each track is assigned a track number enabling you to
locate the track you want.
DVD
structure
Disc
Title
Chapter
VIDEO
CD or
CD
structure
Disc
Track
Index
• Index (CD) / Video Index (VIDEO CD)
A number that divides a track into sections to easily locate the
point you want on a VIDEO CD or a CD. Depending on the
disc, no indexes may be recorded.
• Scene
On a VIDEO CD with PBC (playback control) functions, the
menu screens, moving pictures and still pictures are divided
into sections called “scenes.” Each scene is assigned a scene
number enabling you to locate the scene you want.
Note on PBC (Playback Control) (VIDEO CDs)
This player conforms to Ver. 1.1 and Ver. 2.0 of VIDEO CD
standards. You can enjoy two kinds of playback according to the
disc type.
Disc type
You can
VIDEO CDs
without PBC
functions
(Ver. 1.1 discs)
Enjoy video playback (moving pictures)
as well as music.
VIDEO CDs with
PBC functions
(Ver. 2.0 discs)
Play interactive software using menu
screens displayed on the TV screen (PBC
Playback), in addition to the video
playback functions of Ver. 1.1 discs.
Moreover, you can play high-resolution
still pictures if they are included on the
disc.
When playing DTS*-encoded CDs, excessive noise will be heard
from the analog stereo outputs. To avoid possible damage to the
audio system, the consumer should take proper precautions
when the analog stereo outputs of the DVD player are connected
to an amplification system. To enjoy DTS Digital Surround™
playback, an external 5.1-channel DTS Digital Surround™
decoder system must be connected to the digital output of the
DVD player.
This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
* “DTS” is a trademark of Digital Theater Systems, Inc.
5
Precautions
On safety
• Caution – The use of optical instruments with this
product will increase eye hazard.
• Should any solid object or liquid fall into the cabinet,
unplug the player and have it checked by qualified
personnel before operating it any further.
On power sources
• The player is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the player itself has been turned off.
• If you are not going to use the player for a long time, be
sure to disconnect the player from the wall outlet. To
disconnect the AC power cord (mains lead), grasp the
plug itself; never pull the cord.
• Should the AC power cord (mains lead) need to be
changed, have it done at a qualified service shop only.
On placement
• Place the player in a location with adequate ventilation
to prevent heat build-up in the player.
• Do not place the player on a soft surface such as a rug
that might block the ventilation holes on the bottom.
• Do not place the player in a location near heat sources,
or in a place subject to direct sunlight, excessive dust or
mechanical shock.
On operation
• If the player is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture
may condense on the lenses inside the player. Should
this occur, the player may not operate properly. In this
case, remove the disc and leave the player turned on for
about half an hour until the moisture evaporates.
• When you move the player, take out any discs. If you
don’t, the disc may be damaged.
On adjusting volume
• Do not turn up the volume while listening to a section
with very low level inputs or no audio signals. If you
do, the speakers may be damaged when a peak level
section is played.
On cleaning
• Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any questions or problems concerning your
player, please consult your nearest Sony dealer.
6
IMPORTANT NOTICE
Caution: The enclosed DVD player is capable of
holding a still video image or on-screen display
image on your television screen indefinitely. If you
leave the still video image or on-screen display image
displayed on your TV for an extended period of time
you risk permanent damage to your television screen.
Projection televisions are especially susceptible to
this.
Notes About the Discs
On handling discs
• To keep the disc clean, handle the disc by its edge. Do
not touch the surface.
• Do not stick paper or tape on the disc.
If there is glue (or a similar substance) on the disc,
remove the glue completely before using the disc.
• Do not expose the disc to direct sunlight or heat sources
such as hot air ducts, or leave it in a car parked in direct
sunlight as the temperature may rise considerably
inside the car.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a cleaning cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
On novelty discs
• Do not use irregularly shaped CDs such as heart- or
star-shaped CDs as they may cause the player to
malfunction.
Getting
Started
Check that you have the following items:
• Audio/video connecting cord (1)
• Remote commander (remote) (1)
• Size AA (R6) batteries (2)
Inserting batteries into the remote
You can control the player using the supplied remote.
Insert two Size AA (R6) batteries by matching the + and –
ends on the batteries to the markings inside the
compartment. When using the remote, point it at the
remote sensor on the player.
z You can control TVs or AV receivers (amplifiers) using the
supplied remote
See page 53.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing,
particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or lighting
apparatuses. Doing so may cause a malfunction.
• If you do not use the remote for an extended period of time,
remove the batteries to avoid possible damage from battery
leakage and corrosion.
7
Getting Started
This section describes how to hook up
the CD/DVD player to a TV (with
audio/video input jacks) and/or an
AV receiver (amplifier). You cannot
connect this player to a TV which
does not have a video input
connector. Be sure to turn off the
power of each component before
making the connections.
Unpacking
TV Hookups
Getting Started
This connection is for listening to the sound through TV
speakers (L: left, R: right). Refer to the instructions
supplied with the component to be connected.
Required cords
Audio/video connecting cord (supplied) (1)
Yellow
White (L)
Red (R)
z You can enjoy surround sound using your TV’s built-in
speakers
You can use 3D sound imaging to create virtual rear speakers
from the sound of built-in TV speakers without using actual rear
speakers (VES TV: Virtual Enhanced Surround TV). For details,
see page 33.
Yellow
White (L)
Red (R)
S video cord (not supplied) (1)
When connecting the cords, be sure to match the color-coded
cord to the appropriate jacks on the components: Yellow (video)
to Yellow, Red (right) to Red and White (left) to White. Be sure to
make connections firmly to avoid hum and noise.
If your TV has an S video input connector, connect the
component via the S VIDEO OUT connector using an S video
cord (not supplied). You will get a better picture.
Refer to the instructions supplied with the TV to be connected.
CD/DVD player
AUDIO OUT
DIGITAL OUT
VIDEO OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL OPTICAL
R
To AUDIO
OUT
S VIDEO OUT
COMPONENT VIDEO OUT
Y
L
To VIDEO
OUT
PB/B-Y PR/R-Y
To an AC outlet
To S VIDEO OUT
To S VIDEO input
TV
INPUT
To video input
VIDEO
S VIDEO
L
AUDIO
R
To audio input
: Signal flow
8
CD/DVD player
Monitor or projector
with component video
input connectors
COMPONENT VIDEO OUT
COMPONENT
VIDEO IN
PR
Y
PB/B-Y
PR/R-Y
PB
Y
Setups for the player
Getting Started
If you connect the player to a monitor or
projector having component video input
connectors that conform to output signals from
the COMPONENT VIDEO OUT (Y, PB/B-Y, PR/R-Y)
connectors on the player
Connect the component via the COMPONENT VIDEO
OUT connectors using three video connecting cords (not
supplied) of the same kind. You will get a better picture.
Some setup adjustments are necessary for the player
depending on the TV or other components to be
connected.
Use the setup display to change the various settings.
For details on using the setup display, see page 43.
• To connect the player to a normal TV
In the setup display, set “TV TYPE” in “SCREEN
SETUP” to “4:3 LETTER BOX” (default setting) or “4:3
PAN SCAN.” For details, see page 47.
• To connect the player to a TV having the WIDE
MODE function
In the setup display, set “TV TYPE” in “SCREEN
SETUP” to “16:9/4:3 WIDE MODE.” For details, see
page 47.
• To connect the player to a wide-screen TV
In the setup display, set “TV TYPE” in “SCREEN
SETUP” to “16:9/4:3 WIDE MODE.” For details, see
page 47.
Notes
• Refer to the instructions supplied with the component to be
connected.
• Do not connect this player to a video deck. If you do, noise
may appear in the picture.
VCR
CD/DVD
player
TV
Connect
directly
• Depending on the TV or receiver (amplifier), sound distortion
may occur because the audio output level is high. In this case,
set “AUDIO ATT” in “AUDIO SETUP” to “ON” in the setup
display. For details, see page 51.
9
Receiver (Amplifier) Hookups
Getting Started
This connection is for listening to the sound through
speakers connected to a receiver lacking a built-in DTS or
Dolby* Digital decoder. Refer as well to the instructions
supplied with the component to be connected.
Required cords
Audio connecting cord (not supplied) (1)
White (L)
White (L)
Red (R)
Red (R)
z You can enjoy surround sounds even if you connect front
speakers only
S video cord (not supplied) (1)
You can use 3D sound imaging to create virtual rear speakers
from the sound of the front speakers (L, R) without using actual
rear speakers (VES:Virtual Enhanced Surround). For details, see
page 33.
When connecting the cords, be sure to match the color-coded
cord to the appropriate jacks on the components: Red (right) to
Red and White (left) to White. Be sure to make connections firmly
to avoid hum and noise.
If you have a digital component such as a receiver (amplifier)
with a digital connector, DAT or MD, connect the component via
the DIGITAL OUT OPTICAL or COAXIAL connector using an
optical or coaxial digital connecting cord (not supplied).
z If you have a digital component with a built-in DTS or Dolby
Digital decoder
You can enjoy multi-channel surround sound by connecting the
component via the DIGITAL OUT OPTICAL or COAXIAL
connector using an optical or coaxial digital connecting cord (not
supplied). For details on hookups and settings, see page 12.
Optical digital connecting cord (not supplied) (1)
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks
of Dolby Laboratories.
Confidential unpublished works. ©1992-1997 Dolby
Laboratories. All rights reserved.
Coaxial digital connecting cord (not supplied) (1)
CD/DVD player
AUDIO OUT
DIGITAL OUT
VIDEO OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL OPTICAL
R
S VIDEO OUT
COMPONENT VIDEO OUT
L
Y
To AUDIO
OUT
To DIGITAL
OUT
(OPTICAL)
Take off the
cap.
PB/B-Y PR/R-Y
To an AC outlet
To S VIDEO
OUT
TV
INPUT
To S VIDEO
input
To
DIGITAL
OUT
(COAXIAL)
VIDEO
S VIDEO
L
AUDIO
R
To optical digital input
DIGITAL IN
OPTICAL
or
COAXIAL
or
To coaxial digital input
Receiver
(Amplifier)
CD
L
R
: Signal flow
To audio input
10
Receiver
(Amplifier) with
a digital
connector, MD
deck, DAT deck,
etc.
Notes
When you have made the connections using an optical or
coaxial digital connecting cord, do not set “DOLBY
DIGITAL” to “DOLBY DIGITAL” and “DTS” to “ON.” If you
do, a loud noise will suddenly come out from the
speakers, affecting your ears or causing the speakers to be
damaged.
Setups for the player
Some setup adjustments are necessary for the player
depending on the components to be connected.
Use the setup display to change the various settings.
For details on using the setup display, see page 43.
• To listen to the sound through speakers connected
to a receiver (amplifier) which has a digital
connector and lacks a built-in DTS or Dolby Digital
decoder, or to output the sound to a digital
component such as a DAT or MD deck
Set the “AUDIO SETUP” items in the setup display
(page 51) as shown in the illustration below. These are
the default settings.
AUDIO SETUP
AUDIO ATT:
OFF
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
DTS:
OFF
To set, press
To quit, press
DISPLAY
, then
.
ENTER
Set the
items as
shown
.
Set “VES” to “OFF” in the Control Menu display (page
33). When you select any VES mode other than “OFF,”
no sound will come from the speakers.
Note
When you output the signals which do not reproduce the Dolby
Surround (Pro Logic) effect from the DIGITAL OUT OPTICAL or
COAXIAL connector, set “DOWNMIX” to “NORMAL” in
“AUDIO SETUP” in the setup display (page 52).
11
Getting Started
• You cannot enjoy a picture with an S video signal if your TV
does not conform to the S video signal. When your TV does
not have an S VIDEO input, connect the component via the
VIDEO INPUT connector using the audio/video connecting
cord (supplied) instead of the S video cord. For details, see
page 8.
Refer to the instructions supplied with your TV.
• Refer to the instructions supplied with the component to be
connected.
• You cannot make digital audio recordings of discs recorded in
multi-channel surround format directly using an MD deck or
DAT deck.
• When you connect the component via the DIGITAL OUT
OPTICAL or COAXIAL connector, set Virtual Enhanced
Surround (VES) to “OFF.” Otherwise, the player will not output
signals from the DIGITAL OUT OPTICAL or COAXIAL
connector, if you set “DOLBY DIGITAL” in “AUDIO SETUP”
to “D-PCM.”
5.1 Channel Surround Hookups
Getting Started
With DVDs which contain DTS or Dolby Digital sound,
you can enjoy the surround sound while producing the
effect of being in a movie theater or a concert hall using a
digital component with a built-in DTS or Dolby Digital
decoder (not supplied). The player outputs the surround
sound signals from the DIGITAL OUT OPTICAL and
COAXIAL connectors.
Using a receiver (amplifier) having the OPTICAL or
COAXIAL connector and 6 speakers, you can enjoy even
greater real audio presence in the comfort of your own
home.
Required cords
Optical digital connecting cord* (not supplied) (1)
Setups for the player
Some setup adjustments are necessary for the player
depending on the components to be connected.
Use the setup display to change the various settings.
For details on using the setup display, see page 43.
• When you connect an audio component with a builtin Dolby Digital decoder A
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and
then set “DOLBY DIGITAL” to “DOLBY DIGITAL” in
the setup display. (page 52)
• When you connect an audio component with a builtin DTS decoder B
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and
then set “DTS” to “ON” in the setup display. (page 52)
AUDIO SETUP
OFF
AUDIO ATT:
STANDARD
AUDIO DRC:
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
DOLBY DIGITAL
DOLBY DIGITAL:
DTS:
ON
Coaxial digital connecting cord* (not supplied) (1)
S video cord (not supplied) (1)
To set, press
To quit, press
* Connect the component via the DIGITAL OUT OPTICAL or
COAXIAL connector using an optical or coaxial digital
connecting cord (not supplied). You do not need to connect
both of these cords. See the figure on the next page.
Notes
• Do not connect the power cord to an AC outlet or press the
POWER switch before completing all connections.
• Refer to the instructions supplied with the component to be
connected.
• The cord connectors should be fully inserted into the jacks. A
loose connection may cause hum and noise.
12
DISPLAY
, then
.
ENTER
.
Notes
• When you do not connect an audio component with a
built-in Dolby Digital decoder, do not set “DOLBY DIGITAL”
to “DOLBY DIGITAL.”
• When you do not connect an audio component with a
built-in DTS decoder, do not set “DTS” to “ON.”
TV
Getting Started
To S VIDEO
input
S VIDEO IN
To S VIDEO
OUT
CD/DVD player
AUDIO OUT
DIGITAL OUT
VIDEO OUT
S VIDEO OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL OPTICAL
R
COMPONENT VIDEO OUT
Y
L
To DIGITAL
OUT
(OPTICAL)
Take off the
cap.
To
DIGITAL
OUT
(COAXIAL)
To optical
digital
input
To coaxial
digital input
To an AC outlet
DIGITAL
TV/LD
DVD
VIDEO 2
VIDEO 1
MONITOR S-LINK
AC OUTLET
CTRL A1
TV/LD IN
AC-3 RF
PRE OUT
5.1 INPUT
FRONT
DVD IN
COAX
DVD IN
PB/B-Y PR/R-Y
S-VIDEO
IN
VIDEO
S-VIDEO S-VIDEO S-VIDEO
IN
OUT
IN
VIDEO
VIDEO
VIDEO
S-VIDEO S-VIDEO
IN
OUT
VIDEO
VIDEO
S-VIDEO
OUT
VIDEO
REAR
FRONT
CENTER
L
L
R
R
REAR
WOOFER
CENTER
OPT
AUDIO
IN
TV/LD IN OPT
AUDIO
IN
AUDIO
OUT
AUDIO
IN
AUDIO
OUT
WOOFER
AUDIO
IN
SPEAKERS
L
B
FRONT
A
REAR
CENTER
CD IN OPT
AV Receiver
(Amplifier) with a
built-in DTS
decoder or Dolby
Digital decoder
MD/DAT IN OPT
+
R
SIGNAL
GND
IN
IN
IN
REC OUT
IN
REC OUT
IN
R
L
R
L
R
L
L
MD/DAT OUT OPT
–
R
PHONO TUNER
CD
MD/DAT
TAPE
Center speaker
Front speaker
(R)
INPUT
Front speaker
(L)
Subwoofer
(Active type)
Rear speaker (R)
: Signal flow
Rear speaker (L)
13
Selecting the Language for the On-Screen Display
Getting Started
You can select the language for the setup display, the
Control Menu display or the messages displayed on the
screen. The default setting is “ENGLISH.”
1
2
3
4
5
6
7
8
9
3
Select “LANGUAGE SETUP” using M/m, and then
press ENTER.
LANGUAGE SETUP
OSD:
DVD MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
ORIGINAL
AUDIO FOLLOW
0
ENTER
To set, press
To quit, press
</M/m/,
ORETURN
DISPLAY
1
4
STOP
DVD
To set, press
To quit, press
5
Selected
item
2
SETUP
Select:
, then
DISPLAY
ENTER
.
ENGLISH
ENGLISH
FRENCH
SPANISH
PORTUGUESE
ENTER
.
.
Select the desired language using M/m, then press
ENTER.
CHOIX DE LA LANGUE
ECRANS:
MENU DVD :
AUDIO:
SOUS-TITRE:
ENTER
, then
.
Select “OSD” using M/m, then press , or ENTER.
The languages you can select are displayed.
LANGUAGE SETUP
OSD:
DVD MENU:
AUDIO:
SUBTITLE:
When the player is in stop mode, press DISPLAY
and select “SETUP” using M/m.
The on-screen menu items are different depending on
whether there is a disc in the player or not.
DISPLAY
FRANÇAIS
ANGLAIS
ORIGINAL
IDEM AUDIO
Press ENTER.
The setup display appears on the TV screen.
LANGUAGE SETUP
OSD:
DVD MENU:
AUDIO:
SUBTITLE:
To set, press
To quit, press
14
DISPLAY
ENGLISH
ENGLISH
ORIGINAL
AUDIO FOLLOW
, then ENTER .
.
Pour régler, appuyez sur
, puis sur
ENTER . Pour quitter, appuyez sur DISPLAY .
6
Press DISPLAY.
The setup display disappears.
7
Press DISPLAY repeatedly to turn off the on-screen
menu.
Getting Started
To return to the previous screen
Press ORETURN.
To quit while making a selection
Press DISPLAY.
Note
The languages you can select are the ones displayed in step 4.
For details, see page 46.
15
Playing Discs
This chapter describes how to play a
DVD/CD/VIDEO CD.
Playing Discs
Depending on the DVD or VIDEO CD, some
operations may be different or restricted. Refer to the
instructions supplied with your disc.
!
H
Power indicator
A
@/1
1
2
3
4
5
6
7
8
9
0
1
Turn on your TV.
Turn on the TV and select the video input so that you
can view the pictures from this player.
When using a receiver (amplifier)
Turn on the receiver (amplifier) and select the
appropriate position so that you can listen to the
sound from this player.
2
Press ! on the player.
The player enters standby mode and the power
indicator lights up in red.
3
Press A on the player, and place a disc on the disc
tray.
The player automatically turns on and the power
indicator lights up in green.
With the playback
side facing down
4
Press H.
The disc tray closes and the player starts playback
(continuous play). Adjust the volume on the TV or the
receiver (amplifier).
After following Step 4
xWhen playing a DVD
A DVD menu or title menu may appear on the TV
screen (see page 20).
xWhen playing a VIDEO CD
A menu may appear on the TV screen depending on the
VIDEO CD. You can play the disc interactively,
following the instructions on the menu. (PBC Playback,
see page 21.)
16
Additional operations
A ./>
To turn off the player
Press @/1 on the remote. The player enters standby mode
and the power indicator lights up in red.
To disconnect the power of the player, press ! on the
player.
H
• Do not play DTS sound tracks without first connecting the
player to an audio component having a built-in DTS decoder.
The player outputs the DTS signal via the DIGITAL OUT
OPTICAL and COAXIAL connectors even if “DTS” in “AUDIO
SETUP” is set to “OFF” in the setup display, and may affect
your ears or cause your speakers to be damaged.
• Set the sound to “STEREO” when you play DTS sound tracks
on a CD. (See “Changing the Sound” on page 30.) If you set
the sound to “1/L” or “2/R,” no sound will come from the
DIGITAL OUT OPTICAL and COAXIAL connectors.
• If you play a CD with a DTS sound track, a loud noise may
come out from the AUDIO OUT connectors, affecting your ears
or causing the speakers to be damaged.
The signals of the DTS sound tracks are output from the
DIGITAL OUT OPTICAL and COAXIAL connectors only. No
sound will be output from the AUDIO OUT connectors.
• If the player is connected to an audio component lacking a
built-in DTS decoder, do not set “DTS” in “DIGITAL OUT” to
“ON” in the setup display. Otherwise, when you play the DTS
sound track, a loud noise will come out from the speakers,
affecting your ears or causing the speakers to be damaged.
• When you set “DTS” in “AUDIO SETUP” to “OFF,” no sound
will come out from the DIGITAL OUT OPTICAL and
COAXIAL connectors even if you play DTS sound tracks on
DVDs.
Notes
• If you leave the player or the remote in pause or stop mode for
15 minutes, the screen saver image appears automatically. To
make the screen saver image go away, press H. (If you want
to set the screen saver function to off, see page 47.)
• While playing a disc, do not turn off the player by pressing !.
Doing so may cancel the settings of the menu. When you turn
off the player, press x first to stop playback and then press @/1
on the remote. After the power indicator lights up in red and
the player enters standby mode, press ! on the player.
X x
Z
Notes on playing DTS sound tracks on a CD
Notes on playing DTS sound tracks on a DVD
Playing Discs
To turn on the player
Press ! on the player. The player enters standby mode
and the power indicator lights up in red.
Then press @/1 on the remote. The player turns on and
the power indicator lights up in green. In standby mode,
the player also turns on by pressing A on the player or by
pressing H.
1
2
3
4
5
6
7
8
9
0
./>
H
x
X
To
Operation
Stop
Press x
Pause
Press X
Resume play after pause
Press X or H
Go to the next chapter,
track or scene in
continuous play mode
Press >
Go back to the preceding
chapter, track or scene in
continuous play mode
Press .
Stop play and remove the
disc
Press Z
You can play discs in various modes such as Program Play
using the on-screen menu (Control Menu). For Control
Menu operations, see page 24.
17
Searching for a Particular Point on a Disc Z
You can locate a particular point on a disc at the desired
speed by monitoring the picture.
Playing Discs
1
2
3
4
5
6
7
8
9
0
/
/
Locating a point slowly by watching the
screen (Slow-motion Play)
You can use this function only for DVDs or VIDEO CDs.
When the player is in the pause mode, press
to
locate a point in playback direction, or press
to
locate a point in opposite direction. When you find the
point you want, press H to return to the normal speed
playback.
Each time you press the
or
button during
Slow-motion play, the playback speed changes. Two
speeds are available. With each press, the display changes
as follows:
Playback direction
SLOW1
y SLOW2
Note
Depending on the DVD/VIDEO CD, you may not be able to do
some of the operations described.
Locating a point quickly (Search)
While a disc is playing, keep pressing
to locate a
point in playback direction at the FF1M* speed or keep
pressing
to locate a point in opposite direction at
the FR1m* speed. When you find the point you want,
release the button to return to normal speed playback.
* The FF1M/FR1m playback speed is the one of the scan
speed described below.
Locating a point quickly by playing a disc
in fast forward or fast reverse (Scan)
While a disc is playing, press
to locate a point in
playback direction, or press
to locate a point in
opposite direction. When you find the point you want,
press H to return to normal speed playback.
Each time you press the
or
button during Scan,
the playback speed changes. Three speeds are available.
With each press, the display changes as follows:
Playback direction
x2B (DVD/CD only) t FF1M t FF2M
R
Opposite direction
x2b (DVD only) t FR1m t FR2m
R
The x2B/x2b playback speed is about twice the normal speed.
The FF2M/FR2m playback speed is faster than FF1M/
FR1m.
18
Opposite direction (DVD only)
SLOW1
y SLOW2
The SLOW2 /SLOW2
SLOW1 /SLOW1 .
playback speed is slower than
Playing a disc frame by frame
You can use this function only for DVDs or VIDEO CDs.
When the player is in the pause mode, press
to go
to the next frame. Press
to return to the preceding
frame (DVD only). To return to normal playback, press
H.
Resuming Playback from the Point Where You Stopped the
Disc (Resume Play)
H
H
Notes
• Resume Play may not be available on some DVDs.
• Resume Play is not available in Shuffle or Program Play mode.
• Depending on where you stopped the disc, the player may
resume playback from a different point.
• The point where you stopped playing is cleared when:
– you open or close the disc tray
– you turn the power off by pressing ! on the player
– you change the play mode
– you start playback after selecting a title, chapter or track
– you change the settings in the setup display
x
x
1
While playing a disc, press x to stop playback.
“RESUME” appears on the front panel display and
“Disc will restart from current point. To start from
beginning, press [STOP] again.” appears on the TV
screen.
If “RESUME” does not appear, Resume Play is not
available.
2
Press H.
The player starts playback from the point where you
stopped the disc in Step 1.
zTo play from the beginning of the disc
When the playing time appears on the front panel display before
you start playing, press x to reset the playing time, then press
H.
19
Playing Discs
The player remembers the point where you stopped the
disc and when “RESUME” appears on the front panel
display, you can resume playback from that point.
As long as you do not open the disc tray, Resume Play
will work even if the player enters standby mode by
pressing @/1 on the remote.
Using the DVD’s Menu
Some DVDs have a title menu or a DVD menu that is
provided with DVDs only.
Using the title menu
Playing Discs
A DVD is divided into long sections of a picture or a
music feature called “titles.” When you play a DVD
which contains several titles, you can select the title you
want using the title menu.
Using the DVD menu
Some DVDs allow you to select the disc contents using a
menu. When you play these DVDs, you can select the
language for the subtitles, the language for the sound, etc.,
using the DVD menu.
DVD MENU
TITLE
</M/m/,
ENTER
</M/m/,
ENTER
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
ENTER
DVD MENU
0
</M/m/,
ENTER
TITLE
</M/m/,
1
Press DVD MENU.
The DVD menu appears on the TV screen. The
contents of the menu vary from disc to disc.
2
Press </M/m/, to select the item you want to
change.
Depending on the disc, you can use the number
buttons to select the item.
1
Press TITLE.
The title menu appears on the TV screen. The contents
of the menu vary from disc to disc.
2
Press </M/m/, to select the title you want to
play.
Depending on the disc, you can use the number
buttons to select the title.
3
To change other items, repeat Step 2.
4
Press ENTER.
Press ENTER.
The player starts playing the selected title.
zIf you want to select the language for the DVD menu
3
Notes
• On some DVDs, you may not be able to select the title.
• On some DVDs, a “title menu” may simply be called a “menu”
or “title” in the instructions supplied with the disc. “Press
ENTER.” may also be expressed as “Press SELECT.”
20
Change the setting using “DVD MENU” in “LANGUAGE
SETUP” in the setup display. For details, see page 46.
Note
Depending on the DVD, a “DVD menu” may simply be called a
“menu” in the instructions supplied with the disc.
Playing VIDEO CDs with PBC Functions (PBC Playback)
./>
ENTER
To go back to the menu
Press ORETURN, ., or >.
z To cancel PBC playback of a VIDEO CD with PBC functions
and play the disc in continuous play mode
There are two ways.
• Before you start playing, select the track you want using .
or >, then press ENTER or H.
• Before you start playing, select the track number using the
number buttons on the remote, then press ENTER or H.
“Play without PBC.” appears on the TV screen and the player
starts continuous play. You cannot play still pictures such as a
menu.
To return to PBC playback, press x twice then press H.
Note
H
Number buttons
1
2
3
4
5
6
7
8
9
ORETURN M/m
Depending on the VIDEO CD, “Press ENTER” in Step 3 may be
expressed as “Press SELECT” in the instructions supplied with
the disc.
0
./>
ENTER
H
M/m
ORETURN
1
Start playing a VIDEO CD with PBC functions by
following Steps 1 to 4 in “Playing Discs” on page
16.
2
Select the item number you want.
Press M/m to select the item number.
You can also select the item number with the number
buttons on the remote.
3
Press ENTER.
4
Follow the instructions in the menu for interactive
operations.
Refer to the instructions supplied with the disc, as the
operating procedure may differ according to the
VIDEO CD.
21
Playing Discs
When playing VIDEO CDs with PBC (Play Back Control)
functions (Ver. 2.0 discs), you can enjoy simple interactive
operations, search functions, and other such operations.
PBC Playback allows you to play VIDEO CDs
interactively by following the menu on the TV screen.
On this player, you can use the number buttons, ENTER,
., >, M/m and ORETURN during PBC Playback.
Using the Front Panel Display Z
You can check information about the disc, such as the total
number of titles or tracks or remaining time, using the
front panel display.
Checking the remaining time
Press TIME/TEXT.
Each time you press TIME/TEXT while playing the disc, the
display changes as shown in the following chart.
Playing time and number
of the current chapter
Playing Discs
TIME/TEXT
TITLE
CHAP
HOUR
MIN
SEC
DVD
Press TIME/TEXT
Remaining time of
the current chapter
TITLE
CHAP
HOUR
MIN
SEC
DVD
Press TIME/TEXT
Playing time and number of
the current title
TITLE
HOUR
Displaying information while playing the disc
Playing
status
SEC
Press TIME/TEXT
Remaining time of
the current title
Disc
type
MIN
DVD
When playing back a DVD
Current
chapter
number
TITLE
HOUR
MIN
SEC
DVD
Press TIME/TEXT
TITLE
DVD
CHAP
HOUR
MIN
SEC
MPEG PGM SHUFFLE
DTS ANGLE REPEAT1
Digital A-B
Text
DVD
Current
surround
format
Current
play
mode
Lights up when
you can change
the angle
22
Current title
number
Playing time
Press TIME/TEXT
Notes
• On some DVDs, the chapter number or time may not appear or
you may not be able to change the front panel display.
• While you are doing Shuffle Play or Program Play, the playing
time of the title and the remaining time of the title are not
displayed.
Checking the remaining time
Press TIME/TEXT.
When playing back a CD/VIDEO CD
Each time you press TIME/TEXT while playing a disc, the
display changes as shown in the following chart.
Displaying information while playing a disc
Playing time and current
track number
Playing
status
Current index number
TRACK
VIDEO CD
CD
INDEX
MIN
Playing Discs
TRACK
SEC
CD
INDEX
MIN
SEC
PGM SHUFFLE
REPEAT1
A-B PBC
Press TIME/TEXT
Remaining time of the
current track
TRACK
INDEX
MIN
SEC
CD
Disc type Current
play
mode
Current
track
number
Playing time
Lights up during PBC
playback (VIDEO CD only)
Press TIME/TEXT
Playing time of the disc
MIN
SEC
CD
z When playing VIDEO CDs with PBC functions
The current scene number is displayed instead of the current
track number and the current index number. In this case, the
front panel display does not change when you press TIME/
TEXT. If TEXT is recorded on the disc, the front panel display
changes to the Text display when you press TIME/TEXT (see
page 29).
Press TIME/TEXT
Remaining time of the disc
MIN
SEC
CD
Press TIME/TEXT
Text
CD
Press TIME/TEXT
Note
While you are doing Shuffle Play, or Program Play, the playing
time of the disc and the remaining time of the disc are not
displayed.
23
Using Various
Functions with
the Control
Menu
Using the Control Menu
Display
Using the Control Menu display, you can select the
starting point, play scenes in any order you like, change
the viewing angles, make Digital Cinema Sound settings,
and other such operations.
The possible operations are different depending on the
kind of disc.
For details on each Control Menu display item, see pages
27 to 42.
This chapter describes how to play
discs in various modes and how to
use the convenient features of the onscreen menu (Control Menu).
DISPLAY
ENTER
ORETURN
</M/m/,
1
2
3
4
5
6
7
8
9
0
ENTER
</M/m/,
DISPLAY
1
ORETURN
Press DISPLAY to show the Control Menu display
on the TV screen.
12(27)
18(34)
C 01:32:55
Current
item
24
TITLE
Select:
ENTER
PLAY
DVD
2
Select the item you want using M/m.
12(27)
18(34)
C 01:32:55
SUBTITLE
Select:
,Control Menu display 1
m
Control Menu display 2
(The items except the first three items from the top
are changed to other items.)
m
ADVANCED display (see page 35)
m
Control Menu display off
ENTER
Press ENTER.
12(27)
18(34)
C 01:32:55
PLAY
DVD
The Control Menu display items are different depending
on the disc.
1: ENGLISH
OFF
1: ENGLISH
2: FRENCH
3: SPANISH
SUBTITLE
Select:
To display other items
Each time you press DISPLAY, the Control Menu display
changes as follows:
z You can select some items directly
ENTER
Some items can be selected by pressing the corresponding button
on the remote. In this case, only the item you selected is
displayed. For instructions on using the remote, see the pages of
each relevant item.
Cancel: RETURN
Note
4
12(27)
18(34)
C 01:32:55
PLAY
DVD
Selected
item
1: ENGLISH
OFF
1: ENGLISH
2: FRENCH
3: SPANISH
SUBTITLE
Select:
5
Some Control Menu display items require operations other than
selecting the setting. For details on these items, see the relevant
pages.
Select the item you want using M/m.
Items
ENTER
Cancel: RETURN
Press ENTER.
12(27)
18(34)
C 01:32:55
PLAY
DVD
OFF
SUBTITLE
Select:
ENTER
25
Using Various Functions with the Control Menu
3
PLAY
DVD
1: ENGLISH
Items
Selected
Item
To cancel while making a selection
Press ORETURN.
Control Menu Item List
TITLE (DVD only) (page 27)/
SCENE (VIDEO CD during PBC playback
only) (page 27)/
ADVANCED (DVD only) (page 35)
You can check play information about the bit rate or the
position where the disc is being played (layer).
TRACK (VIDEO CD only) (page 27)
CHAPTER (DVD only) (page 27)/
INDEX (VIDEO CD only) (page 27)
TRACK (CD only) (page 27)
CUSTOM PARENTAL CONTROL (page 36)
Using a registered password, you can set playback
restrictions for a desired disc.
The same password is used for both Parental Control
(page 48) and Custom Parental Control.
INDEX (CD only) (page 27)
Using Various Functions with the Control Menu
You can search for a point on the DVD by selecting the
title, chapter, track, index or scene.
TIME/TEXT (pages 28, 29)
You can check the playing time and remaining time of the
current title, chapter or track and the total playing time or
remaining time of the disc.
You can also search by inputting the time code.
You can check the DVD TEXT or CD TEXT of the disc on
the TV screen and the front panel display.
SETUP (page 43)
Using the setup display, you can do the initial setup,
adjust the picture and sound and the various outputs.
You can also set a language for the subtitles and the setup
display, limit playback by children, and so on. For details
about the setup display, see page 45.
PROGRAM (page 37)
You can play the contents of the disc in the order you
want by arranging the order of the titles, chapters or
tracks on the disc to create your own program.
AUDIO (page 30)
If the DVD is recorded with multilingual tracks, you can
select the language you want while playing the DVD.
If the DVD is recorded in multiple audio formats (PCM,
Dolby Digital or DTS), you can select the audio format
you want while playing the DVD.
With CDs or VIDEO CDs, you can select the sound from
the right or left channel and listen to the sound of the
selected channel through both the right and left speakers.
SUBTITLE (DVD only) (page 32)
With DVDs on which multilingual subtitles are recorded,
you can change the subtitle language whenever you want
while playing the DVD, and turn it on or off whenever
you want.
ANGLE (DVD only) (page 32)
With DVDs on which various angles (multi-angles) for a
scene are recorded, you can change the angles.
VES (DVD only) (page 33)
Select a mode to enjoy multichannel surround sound such
as Dolby Digital.
Even if you connect only TV or front speakers, Virtual
Enhanced Surround (VES) lets you enjoy 3D sound by
using 3D sound imaging to create virtual rear speakers
from the sound of the front speakers (L, R) without using
actual rear speakers.
26
SHUFFLE (page 39)
You can have the player “shuffle” titles, chapters or tracks
and play them in a random order. Subsequent
“shuffling” may produce a different playing order.
REPEAT (page 40)
You can play all the titles/tracks on a disc or a single title/
chapter/track repeatedly.
A-B REPEAT (page 41)
You can play a specific portion of a title, chapter, or track
repeatedly.
Searching for a Title/Chapter/Track/Index/Scene
Z
2
You can search the disc by title, chapter, track, index or
scene.
12(27)
– –(34)
C 01:32:55
CHAPTER
Number buttons
3
PLAY
DVD
ENTER
.”
PLAY
DVD
Cancel: RETURN
Select the number of the title, chapter, track, index
or scene you want to search for using the number
buttons, then press ENTER.
The player starts playback at the selected number.
To cancel the number, press CLEAR before pressing
ENTER.
To cancel while making a selection
Press ORETURN.
TITLE
Select:
1
ENTER
Notes
Select “TITLE,” “CHAPTER,” “TRACK,” “INDEX” or
“SCENE” using M/m.
“
” is highlighted. (
• The title, chapter or track number displayed is the same
number recorded on the disc.
• The index numbers are not displayed during PBC playback of
VIDEO CDs.
refers to a number)
The number in parentheses indicates the total number
of titles, chapters, tracks, indexes or scenes.
12(27)
18(34)
C 01:32:55
CHAPTER
Select:
PLAY
DVD
ENTER
27
Using Various Functions with the Control Menu
Select “TITLE,” “CHAPTER,” “TRACK,” “INDEX” or
“SCENE” after pressing DISPLAY.
When you play back a DVD, “TITLE” and “CHAPTER”
are displayed.
When you play back a VIDEO CD/CD, “TRACK” and
“INDEX” are displayed. When you play back a VIDEO
CD with PBC functions, “SCENE” is displayed.
12(27)
18(34)
C 01:32:55
Press , or ENTER.
“
” changes to “– –
Checking the Playing Time
and Remaining Time
Z
Selecting a Starting Point
Using the Time Code
Z
You can check the playing time and remaining time of the
current title, chapter or track and the total playing time or
remaining time of the disc.
You can search for a starting point by inputting the time
code.
Using Various Functions with the Control Menu
Press DISPLAY. Then press TIME/TEXT on the remote to
change the time information.
You can also check the DVD TEXT or CD TEXT. See page
29.
12(27)
18(34)
C 01:32:55
TIME/TEXT
Select:
Select “TIME/TEXT” after pressing DISPLAY.
The time code corresponds to the approximate actual
playing time. For example, to search for a scene 2 hours 10
minutes 20 seconds past the beginning, input 2:10:20.
12(27)
18(34)
C 01:32:55
PLAY
DVD
TIME/TEXT
Select:
ENTER
ENTER
When playing a DVD
x TIME/TEXT
•C
: Playing time of the current chapter
• C–
: Remaining time of the current
chapter
•T
: Playing time of the current title
• T–
: Remaining time of the current title
1
When playing a VIDEO CD (in continuous play) or
CD
x TIME/TEXT
•T
: Playing time of the current track
• T–
: Remaining time of the current track
•D
: Playing time of the current disc
• D–
: Remaining time of the current disc
Select “C
” (playing time of the
current chapter) when playing a DVD.
12(27)
18(34)
C 01:32:55
When playing a VIDEO CD (during PBC playback)
x TIME/TEXT
•
: Playing time of the current scene
TIME/TEXT
Select:
2
PLAY
DVD
ENTER
Press , or ENTER.
Time code changes to “T – – : – – : – –.”
12(27)
18(34)
T – –:– –:– –
PLAY
DVD
z You can select “TIME/TEXT” directly
Press TIME/TEXT on the remote. Each time you press the
button, the time information changes.
TIME/TEXT
Number buttons
28
PLAY
DVD
ENTER
Cancel: RETURN
3
Input the time code using the number buttons,
then press ENTER.
The player starts playback at the selected time code.
To cancel the number, press CLEAR before pressing
ENTER.
To cancel while making a selection
Press ORETURN.
Note
You can check the DVD TEXT or CD TEXT of the disc on
the TV screen and the front panel display.
DVD TEXT and CD TEXT are information recorded on the
disc which you cannot change.
Press DISPLAY. Then press TIME/TEXT on the remote
until DVD/CD TEXT is displayed.
The information is displayed at the bottom of the display.
12(27)
18(34)
C 01:32:55
DVD/CD
TEXT
PLAY
DVD
TIME/TEXT
BRAHMS SYMPHONY NO – 4
z You can select “TIME/TEXT” directly
Press TIME/TEXT on the remote. To display DVD/CD TEXT,
press TIME/TEXT until DVD/CD TEXT is displayed.
zYou can view the entire DVD/CD TEXT recorded on the disc
DVD/CD TEXT is scrolled on the front panel display.
Notes
• DVD TEXT is displayed only in English.
• “NO TEXT” appears when the DVD/CD TEXT is not recorded
on the disc.
• This player can only display the first level of DVD/CD TEXT
information.
29
Using Various Functions with the Control Menu
When you input the time code, input the playing time of the title,
not the chapter or track time.
Viewing the Disc
Information
Z
Changing the Sound
Using Various Functions with the Control Menu
If the DVD is recorded with multilingual tracks, you can
select the language you want while playing the DVD.
If the DVD is recorded in multiple audio formats (PCM,
Dolby Digital or DTS), you can select the audio format
you want while playing the DVD.
With multiplex CDs or VIDEO CDs, you can select the
sound from the right or left channel and listen to the
sound of the selected channel through both the right and
left speakers. In this case, the sound loses its stereo effect.
For example, with a disc containing a song, the right
channel may output the vocals and the left channel may
output the instrumental. If you only want to hear the
instrumental, you can select the left channel and hear it
from both speakers.
Select “AUDIO” after pressing DISPLAY.
PLAY
12(27)
DVD
18(34)
C 01:32:55
1: ENGLISH
PROGRAM FORMAT
1: ENGLISH
DOLBY DIGITAL 3/2.1
2: ENGLISH
3: FRENCH
L
C
R
LFE
LS
AUDIO
Select:
ENTER
RS
Cancel: RETURN
x AUDIO
When playing a DVD
Select the language. The languages you can select are
different depending on the DVD. When 4 digits are
displayed, they represent the language code. Select the
language code from the list on page 62.
When the same language is displayed two or more times,
the DVD is recorded in multiple audio formats. The
current audio format is shown on the “PROGRAM
FORMAT” display.
When playing a VIDEO CD or a CD
The default setting is underlined.
• STEREO : The standard stereo sound
• 1/L : The sound of the left channel (monaural)
• 2/R : The sound of the right channel (monaural)
z You can select “AUDIO” directly
Press AUDIO on the remote. Each time you press the button, the
item changes.
30
Notes
• Depending on the DVD, you may not be able to change the
languages even if multilingual tracks are recorded on the DVD.
• While playing the CD/VIDEO CD, standard stereo playback
will be resumed when:
– you open or close the disc tray
– the player enters standby mode by pressing @/1 on the
remote
– you turn the power off by pressing ! on the player
• While playing the DVD, the sound may be changed when:
– you open or close the disc tray
– you change the title
• If “DTS” is set to “OFF” in “AUDIO SETUP,” the DTS track
selection option will not appear on the screen even if the disc
contains DTS tracks.
Displaying the audio information of the
disc
The display examples are as follows:
•PCM (stereo)
1: ENGLISH
When you select “AUDIO,” the channels being played are
displayed on the screen.
In Dolby Digital format, multiple signals ranging from
monaural to 5.1 channel signals can be recorded on a
DVD. Depending on the DVD, the number of the
recorded channels may be different.
PLAY
DVD
PROGRAM FORMAT
DOLBY DIGITAL 3/2.1
L
C
R
LFE
LS
AUDIO
Select:
RS
Current
audio
format*
AUDIO
Select:
•Dolby Surround
1: ENGLISH
PROGRAM FORMAT
DOLBY DIGITAL 2/0
DOLBY SURROUND
L
C
R
Current
playing
program
format**
S
AUDIO
Select:
ENTER
* “PCM,” “DTS” or “DOLBY DIGITAL” is displayed. In
case of “DOLBY DIGITAL,” the channels in the playing
track are displayed by numbers as follows:
For Dolby Digital 5.1 ch:
ENTER
ENTER
•Dolby Digital 5.1ch
“LFE” appears only when a disc contains an LFE signal
component. “LFE” remains on the “PROGRAM
FORMAT” display even if the LFE signal component is
not being output.
Rear component 2
1: ENGLISH
PROGRAM FORMAT
DOLBY DIGITAL 3/2.1
DOLBY DIGITAL 3 / 2. 1
Front component 2
+ Center component 1
L
LFE (Low
Frequency Effect)
component 1
** The letters in the program format display mean the
following:
L:
Front (left)
R:
Front (right)
C:
Center (monaural)
LS: Rear (left)
RS: Rear (right)
S:
Rear (monaural) – the rear component of the
Dolby Surround processed stereo signal and the
Dolby Digital signal.
LFE: – LFE (Low Frequency Effect)
C
R
LFE
LS
AUDIO
Select:
RS
ENTER
•DTS
“LFE” is always enclosed in a solid line regardless of the
LFE signal component being output.
1: ENGLISH
PROGRAM FORMAT
DTS 3/2.1
L
C
R
LFE
LS
AUDIO
Select:
RS
ENTER
Note
When the signal does not contain rear signal components such as
LS, RS or S, the Virtual Enhanced Surround (VES) effect cannot be
heard (page 33).
31
Using Various Functions with the Control Menu
12(27)
18(34)
C 01:32:55
1: ENGLISH
PROGRAM FORMAT
PCM 48kHz 24bit
Displaying the Subtitles
Changing the Angles
Z
With DVDs on which subtitles are recorded, you can turn
the subtitles on and off whenever you want while playing
the DVD.
With DVDs on which multilingual subtitles are recorded,
you can change the subtitle language whenever you want
while playing the DVD, and turn it on or off whenever
you want. For example, you can select the language you
want to practice and turn the subtitles on for better
understanding.
With DVDs on which various angles (multi-angles) for a
scene are recorded, you can change the angles. For
example, while playing a scene of a train in motion, you
can display the view from either the front of the train, the
left window of the train or from the right window without
having the train’s movement interrupted.
Using Various Functions with the Control Menu
Select “ANGLE” after pressing DISPLAY. When the
angles can be changed, the “ANGLE” indicator lights up
in green.
Select “SUBTITLE” after pressing DISPLAY.
12(27)
18(34)
C 01:32:55
12(27)
18(34)
C 01:32:55
PLAY
DVD
PLAY
DVD
1(9)
1: ENGLISH
OFF
1: ENGLISH
2: FRENCH
3: SPANISH
Indicator
ANGLE
Select:
SUBTITLE
Select:
ENTER
ENTER
Cancel: RETURN
1
Select “ANGLE.”
x SUBTITLE
Select the language. The languages you can select are
different depending on the DVD. When 4 digits are
displayed, they indicate the language code. Select the
language code from the list on page 62.
12(27)
18(34)
C 01:32:55
PLAY
DVD
1(9)
z You can select “SUBTITLE” directly
Press SUBTITLE on the remote. Each time you press the button,
the item changes.
ANGLE
Select:
Notes
• When playing a DVD on which no subtitles are recorded, no
subtitles appear.
• Depending on the DVD, you may not be able to turn the
subtitles on even if they are recorded on the DVD.
• Depending on the DVD, you may not be able to turn the
subtitles off.
• The type and number of languages for subtitles vary from disc
to disc.
• Depending on the DVD, you may not be able to change the
subtitles even if multilingual subtitles are recorded on it.
• While playing the DVD, the subtitle may change when:
– you open or close the disc tray
– you change the title
2
Press ,.
The number of the angle changes to “–.” The number
in parentheses indicates the total number of angles.
12(27)
18(34)
C 01:32:55
PLAY
DVD
(9)
ANGLE
Number buttons
32
ENTER
ENTER
Cancel: RETURN
Digital Cinema Sound
Settings
3
Select the angle number using the number buttons
or M/m, then press ENTER.
The angle is changed to the selected angle.
12(27)
18(34)
C 01:32:55
PLAY
DVD
5(9)
ENTER
z You can select “ANGLE” directly
Press ANGLE on the remote. Each time you press the button, the
angle changes.
Notes
Select “VES” after pressing DISPLAY. When you select
any item except “OFF,” the “VES” indicator lights up in
green.
• The number of angles varies from disc to disc or from scene to
scene. The number of angles that can be changed on a scene is
equal to the number of angles recorded for that scene.
• Depending on the DVD, you may not be able to change the
angles even if multi-angles are recorded on the DVD.
12(27)
18(34)
C 01:32:55
PLAY
DVD
VES TV
Indicator
VES TV
VES A
VES B
VES
Select:
ENTER
Cancel: RETURN
x VES
Select the desired item. For details on each item, see
“Effects of each item.”
The default setting is underlined.
• OFF
• VES TV
• VES A
• VES B
• VIRTUAL SEMI MULTI DIMENSION
33
Using Various Functions with the Control Menu
ANGLE
Select:
Select a mode to enjoy multichannel surround sound such
as Dolby Digital.
Even if you connect only a stereo TV or front speakers,
Virtual Enhanced Surround (VES) lets you enjoy 3D
sound by using 3D sound imaging to create virtual rear
speakers from the sound of the front speakers (L: left, R:
right) without using actual rear speakers.
The surround sound signals are output from the AUDIO
OUT connectors. These signals are not output from the
DIGITAL OUT OPTICAL or COAXIAL connector.
When you select a surround mode, the player does not
output the Dolby Digital signals from the DIGITAL OUT
OPTICAL or COAXIAL connector if you set “DOLBY
DIGITAL” in “AUDIO SETUP” to “D-PCM.”
Digital Cinema Sound Settings
Effects of each item
OFF
Outputs 2-channel signals for stereo sound. 5-channel
signals for Dolby Digital sound of a DVD are mixed down
to 2-channels.
VIRTUAL SEMI MULTI DIMENSION
Uses 3D sound imaging to create virtual rear speakers
from the sound of the front speakers (L, R) without using
actual rear speakers. This mode creates 5 sets of virtual
speakers surrounding the listener at a 30˚ angle of
elevation.
L
R
Using Various Functions with the Control Menu
VES (Virtual Enhanced Surround) TV
Uses 3D sound imaging to create virtual rear speakers
from the sound of the front speakers (L, R) without using
actual rear speakers. This mode is effective when the
distance between the front L and R speakers is short, such
as built-in speakers on a stereo TV.
TV
z You can select “VES” directly
Press VES on the player. Each time you press the button, the item
changes.
Notes
VES (Virtual Enhanced Surround) A
Uses 3D sound imaging to create virtual rear speakers
from the sound of the front speakers (L, R) without using
actual rear speakers. The virtual speakers are reproduced
as shown in the illustration below.
L
R
VES (Virtual Enhanced Surround) B
Uses 3D sound imaging to create virtual rear speakers
from the sound of the front speakers (L, R) without using
actual rear speakers. The virtual speakers are reproduced
as shown in the illustration below.
L
34
R
• When you select an item, the sound cuts off for a moment.
• When the playing signal does not contain the surround
component, the effects may be difficult to hear even if you
select “VES TV,” “VES A,” “VES B” or “VIRTUAL SEMI MULTI
DIMENSION.”
• Set the front speakers to form an equilateral triangle with the
listening position at the top, or the effects may be difficult to
hear even if you select “VES A,” “VES B” or “VIRTUAL SEMI
MULTI DIMENSION.”
• When you select “VES TV,” “VES A,” “VES B” or “VIRTUAL
SEMI MULTI DIMENSION,” set the surround settings of the
connected units, such as the amplifier, to OFF.
Checking the Play Information
You can check information such as the bit rate or the disc
layer that is being played.
While playing a disc, the approximate bit rate of the
playback picture is always displayed as Mbps (Mega bit
per second) and the audio as kbps (kilo bit per second).
By pressing DISPLAY repeatedly, you can display either
“BIT RATE” or “LAYER,” whichever was selected in
“ADVANCED.”
Select “ADVANCED” after pressing DISPLAY.
BIT RATE
12(27)
18(34)
C 01:32:55
PLAY
DVD
BIT RATE
BIT RATE
384kbps
Audio
384 kbps
0
ADVANCED
Select:
5
Mbps
10
0
5
10
Mbps
Video
ENTER
x ADVANCED
The default setting is underlined.
When playing a DVD
• BIT RATE: displays the bit rate.
• LAYER: displays the layer and the pick-up point.
• OFF: turns off ADVANCED display.
Bit rate refers to the amount of video/audio data per
second in a disc. The higher the bit rate, the larger the
amount of data. When the bit rate level is high, there is a
large amount of data. However, this does not always
mean that you can get higher quality pictures or sounds.
LAYER
Appears when the DVD has
dual layers
Indicates the approximate point where the disc is playing.
If it is a dual-layer DVD, the player indicates which layer
is being read (“Layer 0” or “Layer 1”).
For details on the layers, see page 60 (DVD).
35
Using Various Functions with the Control Menu
BIT RATE
Displays of each item
Locking Discs (Custom Parental Control) Z
Using a registered password, you can set playback
restrictions for the desired disc.
You can set the same Custom Parental Control password
for up to 50 discs. When you set the fifty-first disc, the
first disc is canceled.
The same password is used for both Parental Control
(page 48) and Custom Parental Control.
3
x If you have not entered a password
The display for entering a password appears.
CUSTOM PARENTAL CONTROL
Enter a new 4-digit password, then
press ENTER .
Select “CUSTOM PARENTAL CONTROL” after pressing
DISPLAY.
Using Various Functions with the Control Menu
12(27)
18(34)
C 01:32:55
Select “ON,” using M/m, then press ENTER.
PLAY
DVD
To return, press
The display for confirming the password appears. Skip
Step 4.
CUSTOM PARENTAL CONTROL
ENTER
Select:
CUSTOM PARENTAL CONTROL
Setting the Custom Parental Control for a
disc
1
Insert the disc you want to lock.
If a disc is playing, press x to stop playback.
2
Select “CUSTOM PARENTAL CONTROL” using M/m,
then press ENTER.
STOP
DVD
Enter password, then press
To return, press
4
OFF
ON
PASSWORD
CUSTOM PARENTAL CONTROL
ENTER Cancel: RETURN
Select:
RETURN
ENTER
.
.
Enter a 4-digit password using the number
buttons, then press ENTER.
The digits change to asterisks ( ), and the display for
confirming the password appears.
CUSTOM PARENTAL CONTROL
To confirm, enter password again,
then press ENTER .
To return, press
5
36
.
x When you have already registered a password
OFF
12(27)
18(34)
C 01:32:55
RETURN
RETURN
.
Enter the same 4-digit password using the number
buttons, then press ENTER.
“Custom parental control is set.” appears and then the
screen returns to the Control Menu display.
Creating Your Own
Program (Program Play)
To return to the normal screen
Press ORETURN.
To turn off the Custom Parental Control function
1 Select “CUSTOM PARENTAL CONTROL” using M/m,
then press ENTER.
2 Select “OFF,” using M/m, then press ENTER.
3 Enter your 4-digit password using the number buttons,
then press ENTER.
Select “PROGRAM” after pressing DISPLAY. When you
select “ON,” the “PROGRAM” indicator lights up in
green.
12(27)
18(34)
C 01:32:55
OFF
OFF
SET
ON
Indicator
PROGRAM
Select:
Playing the disc for which the Custom
Parental Control is set
1
Insert the disc.
The CUSTOM PARENTAL CONTROL display
appears.
ENTER
PLAY
DVD
Cancel: RETURN
x PROGRAM
The default setting is underlined.
• OFF: plays normally.
• SET,: allows you to create your own program.
• ON: plays Program Play.
Creating the program
CUSTOM PARENTAL CONTROL
Custom parental control is already
set. To play, enter your password
and press ENTER .
1
Select “SET,” in “PROGRAM.”
The programming display appears.
“TRACK” is displayed when you play
a VIDEO CD or a CD.
PROGRAM
2
Enter your 4-digit password using the number
buttons, then press ENTER.
The player starts playback.
z If you forget your password
Enter the 6-digit number “199703” whenever the CUSTOM
PARENTAL CONTROL display asks you for your password, then
press ENTER. The display will ask you to enter a new 4-digit
password.
T
ALL CLEAR
1. TITLE
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
Set:
Start:
––
01
02
03
04
05
ENTER
Quit:
DISPLAY
PLAY
Note
Unless you enter the password, the player cannot play the disc
for which the Custom Parental Control is set. When you do not
know the password, press A and remove the disc.
37
Using Various Functions with the Control Menu
To change the password
1 Select “CUSTOM PARENTAL CONTROL” using M/m,
then press ENTER.
2 Select “PASSWORD,” using M/m, then press ENTER.
3 Enter your 4-digit password using the number buttons,
then press ENTER.
The display for changing the password appears.
4 Enter a new 4-digit password using the number
buttons, then press ENTER.
5 To confirm your password, re-enter it using the number
buttons, then press ENTER.
You can play the contents of the disc in the order you
want by arranging the order of the titles, chapters or
tracks on the disc and create your own program. One
program can be stored in the player and contain up to 99
titles, chapters and tracks.
Creating Your Own Program (Program Play)
2
PROGRAM
Using Various Functions with the Control Menu
ALL CLEAR
1. TITLE – –
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
Set:
Start:
3
x When playing a VIDEO CD or CD
Select the track you want to program.
Press ,.
“01” is highlighted. It is ready to set the first title or
track for Program Play.
Title
Chapter
T
C
Quit:
ALL CLEAR
1. TRACK 0 2
2. TRACK
3. TRACK – –
4. TRACK – –
5. TRACK – –
6. TRACK – –
7. TRACK – –
DISPLAY
Set:
Start:
PLAY
Select the title, chapter or track you want to
program using M/m, then press ENTER.
For example, select title or track 2.
(You can also use the number buttons and ENTER
button to make a selection. In this case, the selected
number is displayed on the screen.)
x When playing a DVD
When both titles and chapters are recorded on the
disc, select the title, then the chapter.
PROGRAM
ALL CLEAR
1. TITLE – –
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
Set:
Start:
ENTER
Quit:
PROGRAM
38
C
––
01
02
03
04
05
ALL
01
02
03
04
05
06
DISPLAY
T
ALL CLEAR
1. TITLE 0 1 – 0 2
2. TITLE
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
Set:
Start:
T
PLAY
ENTER
PLAY
––
01
02
03
04
05
Quit:
DISPLAY
0:15:30
T
PROGRAM
ALL
01
02
03
04
05
06
––
01
02
03
04
05
ENTER
Total time of the
programmed tracks
ENTER
––
01
02
03
04
05
Quit:
DISPLAY
PLAY
4
To program other titles, chapters or tracks, repeat
Step 3.
The programmed titles, chapters or tracks are
displayed in the selected order.
5
Press H to start Program Play.
To stop Program Play
Press CLEAR on the remote.
To cancel programming
Press PROGRAM on the remote.
To change the program
1 In Step 2, select the program number of the title, chapter
or track you want to change using M/m.
2 Follow Step 3 for new programming.
To cancel the programmed order
To cancel all the titles, chapters or tracks in the
programmed order, select “ALL CLEAR” in Step 2.
To cancel the selected program, select the program using
M/m in Step 2 then press CLEAR, or select “– –” in Step 3
then press ENTER.
Playing in Random Order
(Shuffle Play)
z The program remains even after Program Play ends
When you press H, you can play the same program again.
z You can do Repeat Play or Shuffle Play of the programmed
titles, chapters or tracks
During Program Play, press REPEAT or SHUFFLE on the remote.
Or set “REPEAT” or “SHUFFLE” to “ON” in the Control Menu
display.
z You can select “PROGRAM” directly
Press PROGRAM on the remote.
You can have the player “shuffle” titles, chapters or tracks
and play them in a random order. Subsequent “shuffling”
may produce a different playing order.
Select “SHUFFLE” after pressing DISPLAY. When you
select a shuffle mode other than “OFF,” the “SHUFFLE”
indicator lights up in green.
You can program by looking at the front panel display instead of
using the programming display on the TV screen.
When you select Track 3 in a VIDEO CD for Program 1, the front
panel display will appear as follows:
12(27)
18(34)
C 01:32:55
Indicator
PLAY
DVD
CHAPTER
OFF
TITLE
CHAPTER
VIDEO CD
PGM
SHUFFLE
Select:
ENTER
Cancel: RETURN
Program number
x SHUFFLE
Selects the Shuffle Play setting.
The default settings are underlined.
VIDEO CD
PGM
Track number
VIDEO CD
PGM
Notes
• The number of titles, chapters or tracks displayed are the same
number of titles, chapters or tracks recorded on a disc.
• The program is canceled when:
– you open or close the disc tray
– the player enters standby mode by pressing @/1 on the
remote
– you turn the power off by pressing ! on the player
• Depending on the DVD, you may not be able to perform
Program Play.
• If you are using the PBC playback function, you must first stop
the disc before you can set a program.
When playing a DVD and when Program Play is
set to OFF
• OFF: does not play a disc in random order.
• TITLE: has the player “shuffle” titles and play them in a
random order.
• CHAPTER: has the player “shuffle” chapters and play
them in a random order.
When playing a VIDEO CD or CD (when Program
Play is set to OFF)
• OFF: does not play a disc in random order.
• TRACK: has the player “shuffle” tracks and play them
in a random order.
When playing a VIDEO CD, CD or DVD (when
Program Play is set to ON)
• OFF: does not play a disc in random order.
• ON: has the player “shuffle” titles or tracks selected in
Program Play and play them in a random order.
To stop Shuffle Play
Press CLEAR on the remote.
39
Using Various Functions with the Control Menu
z You can select discs, titles, chapters and tracks for the
program by looking at the front panel display
Playing in Random Order (Shuffle Play)
Playing Repeatedly (Repeat
Play)
z You can set Shuffle Play while the disc is stopped
After selecting the “SHUFFLE” option, press H.
The player starts Shuffle Play.
z You can select “SHUFFLE” directly
Press SHUFFLE on the remote. Each time you press the button,
the item changes.
You can play all of the titles or tracks on a disc or a single
title, chapter or track repeatedly.
In Shuffle or Program Play mode, the player repeats the
titles or tracks in the shuffled or programmed order.
You cannot perform Repeat Play during PBC playback of
VIDEO CDs (page 21).
Notes
Using Various Functions with the Control Menu
• Shuffle Play is canceled when:
– you open or close the disc tray
– the player enters standby mode by pressing @/1 on the
remote
– you turn the power off by pressing ! on the player
• Depending on the DVD, you may not be able to perform
Shuffle Play.
• Up to 200 chapters in a disc can be played in random order
when “CHAPTER” is selected.
Select “REPEAT” after pressing DISPLAY. When you
select a repeat mode other than “OFF,” the “REPEAT”
indicator lights up in green.
12(27)
18(34)
C 01:32:55
Indicator
PLAY
DVD
DISC
OFF
DISC
TITLE
CHAPTER
REPEAT
Select:
ENTER
Cancel: RETURN
x REPEAT
Selects the Repeat Play setting.
The default settings are underlined.
When playing a DVD and when Program Play and
Shuffle Play are set to OFF
• OFF: does not play repeatedly.
• DISC: repeats all of the titles.
• TITLE: repeats the current title on a disc.
• CHAPTER: repeats the current chapter.
When playing a VIDEO CD/CD and when Program
Play and Shuffle Play are set to OFF
• OFF: does not play repeatedly.
• DISC: repeats all of the tracks on a disc.
• TRACK: repeats the current track.
When Program Play or Shuffle Play is set to ON
• OFF: does not play repeatedly.
• ON: repeats Program Play or Shuffle Play.
To stop Repeat Play
Press CLEAR on the remote.
40
Repeating a Specific
Portion (A-B Repeat)
z You can set Repeat Play while the disc is stopped
After selecting the “REPEAT” option, press H.
The player starts Repeat Play.
z You can select “REPEAT” directly
Press REPEAT on the remote. Each time you press the button, the
item changes.
Notes
Select “A-B REPEAT” after pressing DISPLAY. During AB Repeat Play, the “A-B REPEAT” indicator lights up in
green.
12(27)
18(34)
C 01:32:55
PLAY
DVD
OFF
SET
OFF
Indicator
A–B REPEAT
Select:
ENTER
Cancel: RETURN
x A-B REPEAT
The default setting is underlined.
• SET,: sets the A and B points.
• OFF: does not play a specific portion of a title/chapter/
track repeatedly.
41
Using Various Functions with the Control Menu
• Repeat play is canceled when:
– you open or close the disc tray
– the player enters standby mode by pressing @/1 on the
remote
– you turn the power off by pressing ! on the player
• Depending on the DVD, you may not be able to perform
Repeat Play.
You can play a specific portion of a title, chapter or track
repeatedly. This function is useful when you want to do
such things as memorize lyrics.
During PBC Playback of VIDEO CDs (page 21), this
function is available only while playing moving pictures.
Repeating a Specific Portion (A-B Repeat)
Setting a portion for A-B repeat
1
Select “SET,” in “A-B REPEAT.”
The A-B REPEAT setting display appears.
12(27)
18(34)
C 01:32:55
3
When you reach the ending point (point B), press
ENTER again.
The set points are displayed and the player starts
repeating this specific portion.
“A-B” appears on the front panel display during A-B
repeat play.
PLAY
DVD
12(27)
18(34)
C 0 1 : 34 : 30
Using Various Functions with the Control Menu
OFF
SET
OFF
A–B REPEAT
To select, press
Select:
PLAY
DVD
ON
CHAPTER TIME
A: 18 – 01 : 32 : 55
B: 18 – 01 : 34 : 30
ENTER, then
.
Cancel: RETURN
12(27)
18(34)
C 01:32:55
A-B REPEAT
Set point A with
A–B REPEAT
Select:
ENTER
PLAY
DVD
To stop A-B Repeat Play
Press CLEAR on the remote.
ENTER .
z You can select “A-B REPEAT” directly
Press A-B on the remote.
Notes
Return:
2
RETURN
During playback, when you find the starting point
(point A) of the portion to be played repeatedly,
press ENTER.
The starting point (point A) is set.
18(34)
C 01:32:55
A-B REPEAT
Set point B with
DVD
ENTER
.
CHAPTER TIME
A: 18 – 01 : 32 : 55
Cancel:
42
CLEAR
• You can set A-B Repeat for only one specific portion.
• A-B Repeat is canceled when:
– you open or close the disc tray
– the player enters standby mode by pressing @/1 on the
remote
– you turn the power off by pressing ! on the player
• When you set A-B Repeat, the settings for Shuffle Play and
Program Play are canceled.
• You may not be able to set A-B Repeat for some DVD or VIDEO
CD scenes.
Settings and
Adjustments
This chapter describes how to set and
adjust the player using the on-screen
setup menu. Most settings and
adjustments are required to be set
when you first use the player.
This chapter also describes how to set
the remote for controlling the TV or
the AV receiver (amplifier).
Using the Setup Display
Using the setup display, you can do the initial setup,
adjust the picture and sound and set the various outputs.
You can also set a language for the subtitles and the setup
display, limit playback by children, and so on.
For details on each setup display item, see pages 46 to 53.
Note
You can display the setup display only when the player is in stop
mode.
DISPLAY ENTER
</M/m/,
ENTER
ORETURN
</M/m/,
DISPLAY
1
Press DISPLAY and select “SETUP” using M/m.
12(1)
18(34)
C 00:00:00
Selected
item
2
SETUP
Select:
STOP
DVD
ENTER
Press ENTER.
The setup display appears.
LANGUAGE SETUP
OSD:
DVD MENU:
AUDIO:
SUBTITLE:
To set, press
To quit, press
DISPLAY
ENGLISH
ENGLISH
ORIGINAL
AUDIO FOLLOW
, then ENTER .
.
43
Settings and Adjustments
ORETURN
Using the Setup Display
3
Select the main item you want using M/m.
LANGUAGE SETUP
OSD:
DVD MENU:
AUDIO:
SUBTITLE:
Main item
To set, press
To quit, press
4
DISPLAY
, then
.
Settings and Adjustments
To set, press
To quit, press
DISPLAY
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
ENTER
To set, press
To quit, press
.
8
, then
.
To set, press
To quit, press
.
Select the item you want using M/m.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
4:3 LETTER BOX
ON
JACKET PICTURE
4:3 LETTER BOX
4:3 LETTER BOX
4:3 PAN SCAN
16:9/4:3 WIDE MODE
, then
.
ENTER
.
Press ENTER.
4:3 LETTER BOX
ON
JACKET PICTURE
ENTER
DISPLAY
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
9
5
Select the setting you want using </M/m/,.
ENGLISH
ENGLISH
ORIGINAL
AUDIO FOLLOW
Press ENTER.
The selected main item is highlighted.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
7
DISPLAY
16:9/4:3 WIDE MODE
ON
JACKET PICTURE
, then
.
ENTER
.
Press DISPLAY.
The setup display disappears.
10 Press DISPLAY repeatedly to turn off the on-screen
menu.
To return to the previous screen
Press ORETURN.
To set, press
To quit, press
DISPLAY
, then
.
ENTER
.
To quit while making a selection
Press DISPLAY.
Note
6
Some setup display items require operations other than selecting
the setting. For details on these items, see the relevant pages.
Press ENTER.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
To set, press
To quit, press
44
DISPLAY
, then
.
4:3 LETTER BOX
4:3 LETTER BOX
4:3 PAN SCAN
16:9/4:3 WIDE MODE
ENTER
.
Setup Display Item List
The default settings are underlined.
LANGUAGE SETUP (page 46)
CUSTOM SETUP (page 48)
OSD
AUTO PLAY
ENGLISH
OFF
FRENCH
TIMER
SPANISH
DEMO1
PORTUGUESE
DVD MENU
ENGLISH
DEMO2
DIMMER
BRIGHT
FRENCH
DARK
SPANISH
PORTUGUESE
OFF
PAUSE MODE
AUTO
GERMAN
ITALIAN
FRAME
PARENTAL CONTROL ,
TRACK SELECTION
Settings and Adjustments
DUTCH
CHINESE
OFF
JAPANESE
AUTO
DANISH
SWEDISH
FINNISH
NORWEGIAN
AUDIO SETUP (page 51)
AUDIO ATT
RUSSIAN
OTHERS ,
AUDIO
ORIGINAL
OFF
ON
AUDIO DRC
STANDARD
TV MODE
(same as DVD MENU)
WIDE RANGE
SUBTITLE
AUDIO FOLLOW
DOWNMIX
DOLBY SURROUND
(same as DVD MENU)
NORMAL
DIGITAL OUT
SCREEN SETUP (page 47)
TV TYPE
4:3 LETTER BOX
4:3 PAN SCAN
ON
DOLBY DIGITAL
D-PCM
DOLBY DIGITAL
OFF
DTS
OFF
ON
16:9/4:3 WIDE MODE
SCREEN SAVER
ON
OFF
BACKGROUND
JACKET PICTURE
GRAPHICS
BLUE
BLACK
45
Setting the Display Language or Sound Track
(LANGUAGE SETUP)
“LANGUAGE SETUP” allows you to set various
languages for the on-screen display or sound track.
The default settings are underlined.
Select “LANGUAGE SETUP” in the setup display.
LANGUAGE SETUP
OSD:
DVD MENU:
AUDIO:
SUBTITLE:
Settings and Adjustments
To set, press
To quit, press
DISPLAY
, then
.
ENGLISH
ENGLISH
ORIGINAL
AUDIO FOLLOW
ENTER
.
Notes
• When you select a language that is not recorded on the DVD,
one of the recorded languages is automatically selected for the
“DVD MENU,” “AUDIO” and “SUBTITLE” settings.
• Depending on the DVD, the player may not start playing with
the selected language even when you select a language in
“DVD MENU,” “AUDIO” or “SUBTITLE.”
x OSD (On-Screen Display)
Selects the language for the on-screen display.
• ENGLISH
• FRENCH
• SPANISH
• PORTUGUESE
x DVD MENU
Selects the language for the DVD menu.
• ENGLISH
• FRENCH
• SPANISH
• PORTUGUESE
• GERMAN
• ITALIAN
• DUTCH
• CHINESE
• JAPANESE
• DANISH
• SWEDISH
• FINNISH
• NORWEGIAN
• RUSSIAN
• OTHERS,
When you select “OTHERS,,” select and enter the language
code from the list using the number buttons (page 62).
After you have made a selection, the language code (4 digits) is
displayed.
46
x AUDIO
Selects the language for the sound track.
• ORIGINAL: the language given priority in the disc
• ENGLISH
• FRENCH
• SPANISH
• PORTUGUESE
• GERMAN
• ITALIAN
• DUTCH
• CHINESE
• JAPANESE
• DANISH
• SWEDISH
• FINNISH
• NORWEGIAN
• RUSSIAN
• OTHERS,
When you select “OTHERS,,” select and enter the language
code from the list using the number buttons (page 62).
After you have made a selection, the language code (4 digits) is
displayed.
x SUBTITLE
Selects the language for the subtitles.
• AUDIO FOLLOW*
• ENGLISH
• FRENCH
• SPANISH
• PORTUGUESE
• GERMAN
• ITALIAN
• DUTCH
• CHINESE
• JAPANESE
• DANISH
• SWEDISH
• FINNISH
• NORWEGIAN
• RUSSIAN
• OTHERS,
When you select “OTHERS,,” select and enter the language
code from the list using the number buttons (page 62).
After you have made a selection, the language code (4 digits) is
displayed.
* When you select “AUDIO FOLLOW,” the language for the
subtitles changes according to the language for the setting you
selected in “AUDIO.”
Settings for the Display (SCREEN SETUP)
“SCREEN SETUP” allows you to set the display according
to the playback conditions.
The default settings are underlined.
Select “SCREEN SETUP” in the setup display.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
To set, press
To quit, press
DISPLAY
4:3 LETTER BOX
ON
JACKET PICTURE
, then
.
ENTER
.
x BACKGROUND
Selects the background color on picture on the TV screen
in stop mode or while playing a CD.
• JACKET PICTURE: The jacket picture appears in the
background, but only when the jacket picture is already
recorded on the disc.
• GRAPHICS: A preset picture stored in the player
appears in the background.
• BLUE: The background color is blue.
• BLACK: The background color is black.
Note
If a disc which does not contain the jacket picture is played while
“BACKGROUND” is set to “JACKET PICTURE,” the picture
stored in the player will automatically appear in the background.
4:3 LETTER BOX
4:3 PAN SCAN
16:9
4:3 WIDE MODE
Note
Depending on the DVD, “4:3 LETTER BOX” may be selected
automatically instead of “4:3 PAN SCAN” and vice versa.
47
Settings and Adjustments
xTV TYPE
Selects the aspect ratio of the TV to be connected.
• 4:3 LETTER BOX: select this when you connect a
normal TV to the player. Displays a wide picture with
bands on the upper and lower portions of the screen.
• 4:3 PAN SCAN: select this when you connect a normal
TV to the player. Displays the wide picture on the
whole screen automatically and cuts off the portions
that do not fit.
• 16:9/4:3 WIDE MODE: select this when you connect a
wide-screen TV to the player or when you connect a TV
with WIDE MODE function to the player (displays a
wide picture with bands displayed on the upper and
lower portions of the screen).
x SCREEN SAVER
Turns on and off the screen saver. If you turn on the
screen saver, the screen saver image appears when you
leave the player or the remote in pause or stop mode for
15 minutes, or when you play back a CD for more than 15
minutes. The screen saver will help prevent your display
device from becoming damaged.
• ON: turns on the screen saver.
• OFF: turns off the screen saver.
Custom Settings (CUSTOM SETUP)
“CUSTOM SETUP” allows you to set the playback
conditions.
The default settings are underlined.
Playback of some DVDs can be limited depending on the
age of the users. The “Parental Control” function allows
you to set a playback limitation level.
Select “CUSTOM SETUP” in the setup display.
CUSTOM SETUP
AUTO PLAY:
DIMMER:
PAUSE MODE:
PARENTAL CONTROL
TRACK SELECTION:
Settings and Adjustments
To set, press
To quit, press
DISPLAY
, then
.
Limiting Playback by Children (Parental
Control)
OFF
BRIGHT
AUTO
Select “CUSTOM SETUP” in the setup display.
CUSTOM SETUP
AUTO PLAY:
DIMMER:
PAUSE MODE:
PARENTAL CONTROL
TRACK SELECTION:
OFF
ENTER
OFF
.
x AUTO PLAY
Selects the Auto Play setting when you connect the AC
power cord to the AC outlet.
• OFF: does not use “TIMER,” “DEMO1” or “DEMO2” to
start playback.
• TIMER: starts playing when the player is turnd on, or at
any time you want when connected to a timer (not
supplied). Set the timer when the player is in standby
mode (the power indicator lights up in red).
• DEMO1: starts playing the first demonstration
automatically.
• DEMO2: starts playing the second demonstration
automatically.
x DIMMER
Adjusts the lighting of the front panel display.
• BRIGHT: makes the front panel display bright.
• DARK: makes the front panel display dark.
• OFF: turns off the lighting of the front panel display.
x PAUSE MODE (DVD only)
Selects the picture in pause mode.
• AUTO: A picture, including subjects that move
dynamically, is output with no jitter. Normally select
this position.
• FRAME: A picture including subjects that do not move
dynamically is output with high resolution.
x PARENTAL CONTROL,
Sets a password and playback limitation level for DVDs
with playback limitation for children.
The same password is used for both Parental Control and
Custom Parental Control (page 36) .
For details, see “Limiting Playback by Children (Parental
Control).”
To set, press
To quit, press
1
DISPLAY
, then
.
ENTER
.
Select “PARENTAL CONTROL” using M/m, then press
ENTER.
CUSTOM SETUP
AUTO PLAY:
DIMMER:
PAUSE MODE:
PARENTAL CONTROL
TRACK SELECTION:
To set, press
To quit, press
DISPLAY
, then
.
OFF
BRIGHT
AUTO
OFF
ENTER
.
x When you have not entered a password
The display for entering a password appears.
CUSTOM SETUP
PARENTAL CONTROL
Enter a new 4-digit password, then
press ENTER .
To return, press RETURN .
To cancel, press DISPLAY .
x When you have already registered a password
The display for confirming the password appears. Skip
Step 2.
CUSTOM SETUP
PARENTAL CONTROL
Enter password, then press
To return, press RETURN .
To cancel, press DISPLAY .
48
OFF
BRIGHT
AUTO
ENTER
.
2
Enter a password in 4 digits using the number
buttons, then press ENTER.
The digits change to asterisks ( ), and the display for
confirming the password appears.
5
CUSTOM SETUP
CUSTOM SETUP
PARENTAL CONTROL
PARENTAL CONTROL
LEVEL:
STANDARD:
CHANGE PASSWORD
To confirm,enter password again,
then press ENTER .
To return, press RETURN .
To cancel, press DISPLAY .
To set, press
To quit, press
To confirm your password, enter it again using the
number buttons, then press ENTER.
The display for setting the playback limitation level
and changing the password appears.
6
4
DISPLAY
PARENTAL CONTROL
LEVEL:
STANDARD:
CHANGE PASSWORD
OFF
USA
, then ENTER .
.
7
Select “STANDARD” using M/m, then press ,.
PARENTAL CONTROL
LEVEL:
STANDARD:
CHANGE PASSWORD
, then
.
ENTER
.
, then
.
ENTER
OFF
OFF
8:
7:
6:
5:
NC17
R
.
Select the level you want using M/m, then press
ENTER.
CUSTOM SETUP
4:
PG13
USA
OFF
USA
To set, press
To quit, press
DISPLAY
DISPLAY
PARENTAL CONTROL
LEVEL:
STANDARD:
CHANGE PASSWORD
CUSTOM SETUP
To set, press
To quit, press
ENTER
Select “LEVEL” using M/m, then press ,.
To set, press
To quit, press
To set, press
To quit, press
, then
.
CUSTOM SETUP
CUSTOM SETUP
PARENTAL CONTROL
LEVEL:
STANDARD:
CHANGE PASSWORD
DISPLAY
OFF
USA
USA
OTHERS
Settings and Adjustments
3
Select a geographic area as the playback limitation
level standard using M/m, then press ,.
When you select “OTHERS,,” select and enter the
standard code in the table on the next page using the
number buttons.
.
DISPLAY
, then
.
ENTER
.
The lower the value, the more strict the limitation.
To return to the normal screen
Press DISPLAY.
To turn off the Parental Control function and play
the DVD after entering your password
Set “LEVEL” to “OFF” in Step 7, then press H.
49
Custom Settings (CUSTOM SETUP)
To change the password
1 After Step 3, select “CHANGE PASSWORD” using M/
m, then press , or ENTER.
The display for changing the password appears.
2 Follow Steps 2 and 3 to enter a new password.
Settings and Adjustments
Standard
Code number
Argentina
2044
Australia
2047
Austria
2046
Playing a disc which is blocked by the playback
limitation level
1 Insert the disc and press H.
The PARENTAL CONTROL display appears.
2 Enter your 4-digit password using the number buttons,
then press ENTER.
The player starts playback.
When you stop playing the DVD, the level returns to
the original level.
Belgium
2057
Brazil
2070
Canada
2079
Chile
2090
China
2092
Denmark
2115
Finland
2165
z If you forget your password
France
2174
Enter the 6-digit number “199703” whenever the PARENTAL
CONTROL display asks you for your password, then press
ENTER. The display will ask you to enter a new 4-digit
password.
Germany
2109
Hong Kong
2219
India
2248
Notes
Indonesia
2238
• When you play DVDs which do not have the Parental Control
function, playback cannot be limited on this player.
• If you do not set a password, you cannot change the settings
for playback limitation.
• Depending on the DVD, you may be asked to change the
parental control level while playing the disc. In this case, enter
your password, then change the level.
When you stop playing the DVD, the level returns to the
original level.
• The same password is used for both Parental Control and
Custom Parental Control (page 36) .
Italy
2254
Japan
2276
Korea
2304
Malaysia
2363
Mexico
2362
Netherlands
2376
New Zealand
2390
Norway
2379
Pakistan
2427
Philippines
2424
Portugal
2436
Russia
2489
Singapore
2501
Spain
2149
Sweden
2499
Switzerland
2086
Taiwan
2543
Thailand
2528
United Kingdom
2184
50
Settings for the Sound
(AUDIO SETUP)
x TRACK SELECTION
Gives the sound track which contains the highest number
of channels priority when you play a DVD on which
multiple audio formats (PCM, DTS or Dolby Digital
format) are recorded.
• OFF : No priority given.
• AUTO : Priority given.
“AUDIO SETUP” allows you to set the sound according
to the playback conditions.
The default settings are underlined.
Select “AUDIO SETUP” in the setup display.
AUDIO SETUP
AUDIO ATT:
OFF
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
DTS:
OFF
Notes
To set, press
To quit, press
DISPLAY
, then
.
ENTER
.
x AUDIO ATT (attenuation)
If the playback sound is distorted, set this item to “ON.”
The player reduces the audio output level.
Selects the setting of the output from the AUDIO OUT
connectors according to the audio equipment to be
connected.
• OFF: turns off the audio attenuation. Normally select
this position.
• ON: reduces the audio output level so that no sound
distortion occurs. Select this when the playback sound
from the built-in TV speakers is distorted.
Note
The setting does not affect the output from the DIGITAL OUT
OPTICAL and COAXIAL connectors.
x AUDIO DRC (Dynamic Range Control)
Makes the sound clear when the volume is turned down
when playing a DVD. This function works only when
you play a DVD which has the AUDIO DRC function.
This affects the output from the DIGITAL OUT connectors
only when “DOLBY DIGITAL” is set to “D-PCM” in
“DIGITAL OUT,” and it affects the output from the
AUDIO OUT connectors.
• STANDARD: Normally select this position.
• TV MODE: makes the low sounds clear even if you turn
the volume down. It is especially recommended when
you listen to the sound using the speakers of the TV.
• WIDE RANGE: It gives you the feeling of being at a live
performance. When you use high quality speakers, it is
more effective.
Note
When you play DVDs without the AUDIO DRC function, there
may be no effect on the sound.
51
Settings and Adjustments
• When you set this item to “AUTO,” the language may change
depending on the “AUDIO” settings in “LANGUAGE SETUP.”
The “TRACK SELECTION“ setting has higher priority than the
“AUDIO” settings in “LANGUAGE SETUP” (page 46).
• If you set “DTS” in “AUDIO SETUP” to “OFF,” the DTS sound
track is not played even if you set this item to “AUTO” and the
highest-numbered audio channel is recorded in DTS format.
• If PCM, DTS and Dolby Digital sound tracks have the same
number of channels, the player selects PCM, DTS and Dolby
Digital sound tracks in this order.
• Depending on the DVD, the audio channel with priority may
be predetermined. In this case, you cannot give priority to the
DTS or Dolby Digital format by selecting “AUTO.”
Settings for the Sound (AUDIO SETUP)
Settings and Adjustments
x DOWNMIX
Switches the mixing down methods when you play a
DVD on which rear signal components such as LS, RS or S
are recorded in Dolby Digital format. For details on the
rear signal components, see “Displaying the audio
information of the disc” (page 31).
The “DOWNMIX” setting affects the following
connectors:
– AUDIO OUT connectors
– DIGITAL OUT OPTICAL and COAXIAL connectors
(when you set “DOLBY DIGITAL” to “D-PCM” in
“AUDIO SETUP” in the setup display)
• DOLBY SURROUND: when the player is connected to
an audio component that conforms to Dolby Surround
(Pro Logic). The output signals which reproduce the
Dolby Surround (Pro Logic) effect are mixed down to 2
channels.
• NORMAL: when the player is connected to an audio
component that does not conform to Dolby Surround
(Pro Logic). The signals without the Dolby Surround
(Pro Logic) effect are output.
x DIGITAL OUT
Selects output signals via the DIGITAL OUT OPTICAL
and COAXIAL connectors.
• ON: Normally select this position. When you select
“ON,” set “DOLBY DIGITAL” and “DTS.” For details
on setting these items, see “Setting the Digital Output
Signal.”
• OFF: when the player does not output the sound signals
via the DIGITAL OUT OPTICAL and COAXIAL
connectors, the influence of the digital circuit upon the
analog circuit is at a minimum.
Notes
• When you play sound tracks with a 96 kHz sampling
frequency, the output signals from the DIGITAL OUT
(OPTICAL, COAXIAL) are converted to 48 kHz (sampling
frequency). When the signals are output from the AUDIO OUT
connectors, sampling frequency stays at 96 kHz and the output
signals are converted to analog signals.
• When you select “OFF,” you cannot set “DOLBY DIGITAL,”
and “DTS.”
Setting the Digital Output Signal
Switches the methods of outputting audio signals when
you, connect 1. a digital component such as a receiver
(amplifier) having a digital connector, 2. an audio
component having a built-in decoder (Dolby Digital or
DTS), 3. a DAT or MD via the DIGITAL OUT OPTICAL or
COAXIAL connector using an optical or coaxial digital
connecting cord. For connection details, see pages 10 and
12.
When you select “ON,” set “DOLBY DIGITAL” and
“DTS.”
AUDIO SETUP
OFF
AUDIO ATT:
STANDARD
AUDIO DRC:
DOWNMIX:
DOLBY SURROUND
ON
DIGITAL OUT:
D-PCM
DOLBY DIGITAL:
DTS:
OFF
To set, press
To quit, press
DISPLAY
, then ENTER .
.
x DOLBY DIGITAL
Selects the Dolby Digital signals to be output via the
DIGITAL OUT OPTICAL and COAXIAL connectors. You
cannot select this item when you set “DIGITAL OUT” to
“OFF.”
• D-PCM (Downmix PCM): when the player is connected
to an audio component lacking a built-in Dolby Digital
decoder. If you play Dolby Digital sound tracks, the
output audio signals are mixed down to 2 channels.
You can select whether the signals conform to Dolby
Surround (Pro Logic) or not by making adjustments to
the “DOWNMIX” item in “AUDIO SETUP.”
• DOLBY DIGITAL: when the player is connected to an
audio component with a built-in Dolby Digital decoder.
If the player is connected to an audio component
lacking a built-in Dolby Digital decoder, do not set this.
Otherwise, when you play the Dolby Digital sound
track, a loud noise or no sound will come out from the
speakers, affecting your ears or causing the speakers to
be damaged.
Note
When you select “D-PCM,” set Virtual Enhanced Surround (VES)
to “OFF.” Otherwise, the player will not output signals from the
DIGITAL OUT OPTICAL or COAXIAL connector.
52
x DTS
Selects the DTS signals to be output via the DIGITAL OUT
OPTICAL and COAXIAL connectors. You cannot select
this item when you set “DIGITAL OUT” to “OFF.”
• OFF: when the player is connected to an audio
component lacking a built-in DTS decoder.
• ON: when the player is connected to an audio
component having a built-in DTS decoder.
If the player is connected to an audio component
lacking a built-in DTS decoder, do not set this.
Otherwise, when you play the DTS sound track, a loud
noise or no sound will come out from the speakers,
affecting your ears or causing the speakers to be
damaged.
Controlling your TV or AV
Receiver (Amplifier) with
the Supplied Remote Z
If you adjust the remote signal, you can control your TV
or AV receiver (amplifier) with the supplied remote.
Default setting is to control Sony TVs with the mark.
TV @/1
Number buttons
1
2
3
4
5
6
7
8
9
0
Settings and Adjustments
Note
Select the setting correctly. Otherwise, no sound or a strange
sound will come out from the speakers, affecting your ears or
causing the speakers to be damaged.
Controlling TVs or AV receivers
(amplifiers) with the remote
Hold down TV @/1, and enter your TV’s or AV
receiver’s manufacturer’s code (see the table) using the
number buttons. Then release TV @/1.
Code numbers of controllable TVs or
AV receivers (amplifiers)
If more than one code number is listed, try entering them
one at a time until you find the one that works with your
TV or AV receiver (amplifier).
Notes
• If you enter a new code number, the code number previously
entered will be erased.
• When you replace the batteries of the remote commander, the
code number reset to 01 (Sony). Reset the appropriate code
number.
53
Controlling your TV or AV Receiver (Amplifier) with the Supplied Remote
TV
You can control your TV using the keys below.
Manufacturer
Code
number
Manufacturer
Code
number
Sony (default)
01
Panasonic
06, 19
TV @/1
1
2
3
4
5
6
7
8
9
TV/VIDEO
VOL
Settings and Adjustments
Akai
04
Philco
03, 04
AOC
04
Philips
08
Centurion
12
Pioneer
16
Coronado
03
Portland
03
Curis-Mathes
12
Quasar
06, 18
Daytron
12
Radio Shack
05, 14
Emerson
03, 04, 14
RCA
04, 10
Fisher
11
Sampo
12
General Electric
06, 10
Sanyo
11
Gold Star
03, 04, 17
Scott
12
Hitachi
02, 03
Sears
07, 10, 11
By pressing
You can
J.C.Penny
04, 12
Sharp
03, 05, 18
TV @/1
Turn the TV on or off
JVC
09
Sylvania
08, 12
TV/VIDEO
Switch the TV’s input source between
the TV and other input sources
KMC
03
Teknika
03, 08, 14
VOL
Adjust the volume of the TV
Magnavox
03, 08, 12
Toshiba
07
Marantz
04, 13
Wards
03, 04, 12
Note
MGA/Mitsubishi 04, 12, 13, 17
Yorx
12
Depending on the TV, you may not be able to control your TV or
to use some of the buttons above.
NEC
Zenith
15
04, 12
AV receiver (amplifier)
Manufacturer
Code number
Sony
91, 89
Denon
84, 85, 86
Kenwood
92, 93
Onkyo
81, 82, 83
Pioneer
99
Sansui
87
Technics
97, 98
Yamaha
94, 95, 96
0
You can also change the sound volume of the AV receiver
(amplifier) using VOL.
1
2
3
4
5
6
7
8
9
0
VOL
Note
Depending on the AV receiver (amplifier), you may not be able to
control your AV receiver (amplifier).
54
Additional
Information
Troubleshooting
If you experience any of the following difficulties while
using the player, use this troubleshooting guide to help
remedy the problem. Should any problem persist, consult
your nearest Sony dealer.
Power
The power is not turned on.
, Check that the AC power cord is connected
securely.
Picture
Picture noise appears.
, Clean the disc.
, If the video signal from your DVD player has to go
through your VCR to get to your TV, the copyprotection applied to some DVD programs could
affect picture quality. If you still experience
problems after checking your connections, please
try connecting your DVD player directly to your
TV’s S video input, if your TV is equipped with
this input. (page 8)
Even though you set the aspect ratio in “TV
TYPE” in “SCREEN SETUP” of the setup display,
the picture does not fill the screen.
, The aspect ratio is fixed on your DVD.
55
Additional Information
There is no picture.
, Check that the player is connected securely.
, The video connecting cord is damaged. Replace it
with a new one.
, Make sure you connect the player to the video
input connector on the TV. (page 8)
, Make sure you turn on the TV.
, Make sure you select the video input on the TV so
that you can view the pictures from the player.
Troubleshooting
Sound
Additional Information
There is no sound.
, Check that the player is connected securely.
, The audio connecting cord is damaged. Replace it
with a new one.
, Make sure you connect the player to the audio
input connectors on the receiver (amplifier). (page
10)
, Make sure you turn on the TV and the receiver
(amplifier).
, Make sure you select the appropriate input on the
receiver (amplifier) so that you can listen to the
sound from the player.
, The player is in pause mode or in Slow-motion
Play mode. Press H to return to normal play
mode.
, The player is in fast forward or fast reverse mode.
Press H to return to normal play mode.
, When you play Dolby Digital sound tracks and
attempt to output from the DIGITAL OUT
connectors, set “DIGITAL OUT” to ”ON” in the
setup display. Otherwise no sound will come from
the DIGITAL OUT connectors. (page 52)
, You selected a VES mode other than “OFF” in the
Control Menu display when you connected the
component via the DIGITAL OUT OPTICAL or
COAXIAL connector. Set “VES” to “OFF” in the
Control Menu display. (page 33)
, When you play DTS sound tracks, no sound will
come out from the AUDIO OUT connectors. (page
17)
Sound is noisy.
, Clean the disc.
, When you play a CD with DTS sound tracks,
sound noise will come from the AUDIO OUT
connectors. (page 17)
Sound distortion occurs.
, In the setup display, set “AUDIO ATT” in “AUDIO
SETUP” to “ON.”
The sound loses its stereo effect when you play a
VIDEO CD or a CD.
, Set “AUDIO” to “STEREO” in the Control Menu
display. (page 30)
, Make sure you connect the player correctly. (page
8, 10, 12)
The surround effect is difficult to hear when you
are playing a Dolby Digital sound track.
, Depending on the DVD, the output signal may not
be the entire 5.1 channels. It may be monaural or
stereo even if the sound track is recorded in Dolby
Digital format.
Operation
The remote does not function.
, Remove any obstacles between the remote and the
player.
, Use the remote near the player.
, Point the remote at the remote sensor on the
player.
, Replace all of the batteries in the remote with new
ones if they are weak.
The disc does not play.
, There is no disc inside (“Insert disc.” appears on
the TV screen).
Insert a disc.
, Insert the disc correctly with the playback side
facing down on the disc tray.
, Clean the disc.
, The player cannot play CD-ROMs, etc. (page 5)
Insert a DVD, a VIDEO CD, or CD.
, Check the region code of the DVD. (page 4)
, Moisture has condensed inside the player. Remove
the disc and leave the player turned on for about
half an hour. (page 6)
The player does not play from the beginning
when playing a disc.
, Program Play, Shuffle Play, Repeat Play or A-B
Repeat Play has been selected. Press CLEAR.
(pages 37 through 42)
, Resume Play has been selected.
Press x on the front panel or on the remote before
you start playing. (page 19)
, A title menu or a DVD menu automatically
appears on the TV screen when you play your
DVD, or a setup display automatically appears on
the TV screen when you play your VIDEO CD
with PBC functions.
The player starts playing the disc automatically.
, The DVD features the auto playback function.
“AUTO PLAY” in “CUSTOM SETUP” is set to
“TIMER.” (page 48)
Playback stops automatically.
, The disc may contain an auto pause signal. While
playing such a disc, the player stops playback at
the signal.
56
You cannot perform some functions such as Stop,
Search, Slow-motion Play, Repeat Play, Shuffle
Play or Program Play.
, Depending on the disc, you may not be able to do
some of the operations above.
Messages do not appear on the TV screen in the
language you want.
, In the setup display, select the desired language for
the on-screen display in “OSD” under
“LANGUAGE SETUP.” (page 46)
5 numbers or letters are displayed on the screen
and on the front panel display.
, The self-diagnosis function was activated. See the
table on page 58.
The disc tray does not open and “LOCKED” is
displayed on the front panel display.
, Contact your Sony dealer or local authorized Sony
service facility.
The language for the sound track cannot be
changed when you play a DVD.
, Multilingual tracks are not recorded on the DVD.
, Changing the language for the track is prohibited
on the DVD.
Additional Information
The subtitle language cannot be changed when
you play a DVD.
, Multilingual subtitles are not recorded on the
DVD.
, Changing the language for the subtitles is
prohibited on the DVD.
The subtitles cannot be turned off when you play
a DVD.
, Depending on the DVD, you may not be able to
turn the subtitles off.
The angles cannot be changed when you play a
DVD.
, Multi-angles are not recorded on the DVD.
, Change the angles when “ANGLE” appears on the
front panel display. (page 32)
, Changing the angles is prohibited on the DVD.
The player does not operate properly.
, Static electricity, etc., may affect the player's
operation.
Disconnect the AC power cord once, then connect
it again.
Nothing is displayed on the front panel display.
, In the set up display, “DIMMER” in “CUSTOM
SETUP” is set to “OFF.”
Set “DIMMER” to “BRIGHT” or “DARK.” (page
48)
57
Self-diagnosis function
When the self-diagnosis function activates to prevent the player from
malfunctioning, a five-character service number (combination of a letter and
digits) flashes on the screen and on the front panel display. In this case, check the
following table.
C:13:00
First three characters
Cause and/or Corrective Action
C13
•The disc is dirty.
, Clean the disc with a cleaning cloth. (page 6)
C31
•The disc is not inserted correctly.
, Open the disc tray and insert the disc correctly.
Exx (xx is any number)
•To prevent a malfunction, the player has performed the self-diagnosis function.
, When you contact your Sony dealer or local authorized Sony service facility, give
the 5-character service number. (example: E:61:10)
Additional Information
58
Specifications
CD/DVD player
General
Laser
Semiconductor laser
Signal format system
NTSC
Audio characteristics
Supplied accessories
See page 7.
* The signals from AUDIO OUT connectors are measured. When you
play PCM sound tracks with a 96 kHz sampling frequency, the
output signals from the DIGITAL OUT (OPTICAL, COAXIAL) are
converted to 48 kHz (sampling frequency).
Design and specifications are subject to change without notice.
Outputs
Jack
type
Output
level
AUDIO OUT
Phono
jacks
2 Vrms
Over 10 kilohms
(at 50 kilohms)
DIGITAL OUT
(OPTICAL)
Optical
–18 dBm
output
connector
Wave length: 660 nm
DIGITAL OUT
(COAXIAL)
Phono
jack
0.5 Vp-p
75 ohms terminated
VIDEO OUT
Phono
jack
1.0 Vp-p
75 ohms,
sync negative
S VIDEO OUT
4-pin
Y: 1.0 Vp-p
mini DIN
C: 0.286 Vp-p
COMPONENT Phono
jacks
VIDEO OUT
(Y, PB/B-Y,
PR/R-Y)
Y: 1.0 Vp-p
PB/B-Y,
PR/R-Y:
0.7 Vp-p
Load impedance
75 ohms,
sync negative
75 ohms terminated
75 ohms,
sync negative
75 ohms
59
Additional Information
Frequency response
DVD (PCM 96 kHz): 2 Hz to 44 kHz (±1
dB)*
DVD (PCM 48 kHz): 2 Hz to 22 kHz (±0.5
dB)
CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio
More than 110 dB (AUDIO OUT connectors
only)
Harmonic distortion
Less than 0.003 %
Dynamic range
More than 100 dB (DVD)
More than 97 dB (CD)
Wow and flutter
Less than detected value
(±0.001 % W PEAK)
Power requirements
120 V AC, 60 Hz
Power consumption
13 W
Dimensions (approx.)
430 × 69 × 252 mm
(17 × 2 3⁄4 × 10 in.) (w/h/d)
incl. projecting parts
Mass (approx.)
2.8 kg (6 lb 3 oz)
Operating temperature
41 ˚F to 95 ˚F
(5 ˚C to 35 ˚C)
Operating humidity
25 % to 80 %
Glossary
Bit rate (page 35)
Value indicating the amount of video data compressed in
a DVD per second. The unit is Mbps (Mega bit per
second). 1 Mbps indicates that the data per second is
1,000,000 bits. The higher the bit rate, the larger the
amount of data. However, this does not always mean that
you can get higher quality pictures.
Chapter (page 5)
Sections of a picture or a music piece on a DVD that are
smaller than titles. A title is composed of several chapters.
Each chapter is assigned a chapter number enabling you
to locate the chapter you want.
Additional Information
Digital Cinema Sound (DCS) (page 33)
The general name of technology that Sony developed to
enjoy surround sound in a home. It simulates the sound
of a movie editing studio instead of the usual concert hall
so that you can enjoy the surround sound of a movie
theater in the comfort of your own home. The VES
(Virtual Enhanced Surround) system contained in DCS
programs can create the sound image of virtual rear
speakers from the sound of the front speakers (L, R)
without using actual rear speakers.
Dolby Digital (pages 10, 52)
Digital audio compression technology developed by
Dolby Laboratories. This technology conforms to 5.1channel surround sound. The rear channel is stereo and
there is a discrete subwoofer channel in this format.
Dolby Digital provides the same 5.1 discrete channels of
high quality digital audio found in Dolby Digital cinema
audio systems. Good channel separation is realized
because all of the channel data is recorded discretely and
processed in digital.
DVD (page 4)
A disc that contains up to 8 hours of moving pictures even
though its diameter is the same as a CD.
The data capacity of a single-layer and single-sided DVD
is 4.7 GB (Giga Byte) which is 7 times that of a CD. The
data capacity of a dual-layer and single-sided DVD is 8.5
GB, a single-layer and double-sided DVD is 9.4 GB, and a
dual-layer and double-sided DVD is 17 GB.
The picture data uses the MPEG 2 format, one of the
worldwide standards of digital compression technology.
The picture data is compressed to about 1/40 of its
original size. The DVD also uses a variable rate coding
technology that changes the data to be allocated according
to the status of the picture.
Audio data is recorded in Dolby Digital as well as in
PCM, allowing you to enjoy a more real audio presence.
Furthermore, various advanced functions such as the
multi-angle, multilingual, and Parental Control functions
are provided with the DVD.
Multi-angle function (page 32)
Various angles for the scene (viewpoints of the video
camera) are recorded on some DVDs.
Multilingual function (pages 14, 32, 46)
Several languages for the audio track or sub-titles in a
picture are recorded on some DVDs.
Parental Control (page 48)
A function of the DVD used to limit playback of the disc
according to the age of the user and the limitation level in
each country. The limitation varies from disc to disc;
when it is activated, playback is completely prohibited,
violent scenes are skipped or replaced with other scenes,
and so on.
Dolby Pro Logic (page 52)
Audio signal processing technology that Dolby
Laboratories developed for surround sound. When the
input signal contains a surround component, the Pro
Logic process outputs the front, center and rear signals.
The rear channel is monaural.
Playback Control (PBC) (page 21)
Signals encoded on VIDEO CDs (Version 2.0) to control
playback.
By using menus recorded on VIDEO CDs with PBC
functions, you can enjoy playing simple interactive
programs, programs with search functions, and so on.
DTS (pages 12, 53)
Digital audio compression technology that Digital Theater
Systems, Inc. developed. This technology conforms to 5.1channel surround. The rear channel is stereo and there is
a discrete subwoofer channel in this format. DTS provides
the same 5.1 discrete channels of high quality digital
audio. Good channel separation is realized because all of
the channel data is recorded discretely and processed in
digital.
Title (page 5)
The longest section of a picture or a music piece on a
DVD; a movie, etc., for a picture piece on video software;
or an album, etc., for a music piece on audio software.
Each title is assigned a title number enabling you to locate
the title you want.
60
Track (page 5)
Sections of a picture or a music piece on a CD or VIDEO
CD. Each track is assigned a track number enabling you to
locate the track you want.
Additional Information
VIDEO CD (page 4)
A compact disc that contains moving pictures.
The picture data uses the MPEG 1 format, one of the
worldwide standards of digital compression technology.
The picture data is compressed to about 1/140 of its
original size. Consequently, a 12 cm VIDEO CD can
contain up to 74 minutes of moving pictures.
VIDEO CDs also contain compact audio data. Sounds
outside the range of human hearing are compressed while
the sounds we can hear are not compressed. VIDEO CDs
can hold 6 times the audio information of conventional
audio CDs.
There are 2 versions of VIDEO CDs.
• Version 1.1: You can play only moving pictures and
sounds.
• Version 2.0: You can play high-resolution still pictures
and enjoy PBC functions.
This player conforms to both versions.
61
Language Code List
For details, see page 32, 46.
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Additional Information
Code
Language
Code
Language
Code
Language
Code
Language
1027
Afar
1186
Scots Gaelic
1350
Malayalam
1513
Siswati
1028
Abkhazian
1194
Galician
1352
Mongolian
1514
Sesotho
1032
Afrikaans
1196
Guarani
1353
Moldavian
1515
Sundanese
1039
Amharic
1203
Gujarati
1356
Marathi
1516
Swedish
1044
Arabic
1209
Hausa
1357
Malay
1517
Swahili
1045
Assamese
1217
Hindi
1358
Maltese
1521
Tamil
1051
Aymara
1226
Croatian
1363
Burmese
1525
Telugu
1052
Azerbaijani
1229
Hungarian
1365
Nauru
1527
Tajik
1053
Bashkir
1233
Armenian
1369
Nepali
1528
Thai
1057
Byelorussian
1235
Interlingua
1376
Dutch
1529
Tigrinya
1059
Bulgarian
1239
Interlingue
1379
Norwegian
1531
Turkmen
1060
Bihari
1245
Inupiak
1393
Occitan
1532
Tagalog
1061
Bislama
1248
Indonesian
1403
(Afan) Oromo
1534
Setswana
1066
Bengali; Bangla
1253
Icelandic
1408
Oriya
1535
Tonga
1067
Tibetan
1254
Italian
1417
Punjabi
1538
Turkish
1070
Breton
1257
Hebrew
1428
Polish
1539
Tsonga
1079
Catalan
1261
Japanese
1435
Pashto; Pushto
1540
Tatar
1093
Corsican
1269
Yiddish
1436
Portuguese
1543
Twi
1097
Czech
1283
Javanese
1463
Quechua
1557
Ukrainian
1103
Welsh
1287
Georgian
1481
Rhaeto-Romance
1564
Urdu
1105
Danish
1297
Kazakh
1482
Kirundi
1572
Uzbek
1109
German
1298
Greenlandic
1483
Romanian
1581
Vietnamese
1130
Bhutani
1299
Cambodian
1489
Russian
1587
Volapük
1142
Greek
1300
Kannada
1491
Kinyarwanda
1613
Wolof
1144
English
1301
Korean
1495
Sanskrit
1632
Xhosa
1145
Esperanto
1305
Kashmiri
1498
Sindhi
1665
Yoruba
1149
Spanish
1307
Kurdish
1501
Sangho
1684
Chinese
1150
Estonian
1311
Kirghiz
1502
Serbo-Croatian
1697
Zulu
1151
Basque
1313
Latin
1503
Singhalese
1703
Not specified
1157
Persian
1326
Lingala
1505
Slovak
1165
Finnish
1327
Laothian
1506
Slovenian
1166
Fiji
1332
Lithuanian
1507
Samoan
1171
Faroese
1334
Latvian; Lettish
1508
Shona
1174
French
1345
Malagasy
1509
Somali
1181
Frisian
1347
Maori
1511
Albanian
1183
Irish
1349
Macedonian
1512
Serbian
62
Index to Parts and Controls
Refer to the pages indicated in parentheses for details.
Front Panel
8 </M/m/,/ENTER button
Selects and executes the items or settings.
9
(remote sensor) (7)
Accepts the remote control signals.
0 Front Panel Display (22)
Indicates the playing time, etc.
qa H (play) button (16)
Plays a disc.
qs X (pause) button (17)
Pauses playing a disc.
qd x (stop) button (17, 19)
Stops playing a disc.
qf DISPLAY button (24)
Displays the Control Menu display on the TV screen
to set or adjust the Control Menu items.
qg ORETURN button (21, 25)
Press to return to the previously selected screen, etc.
63
Additional Information
1 ! (power) button and indicator (16)
Disconnects the power of the player or places the
player in standby mode.
2 VES (Virtual Enhanced Surround) button and
indicator (33)
Press to select the desired “VES” item. The indicator
lights up for every selected item except “OFF.”
3 Disc tray (16)
Place a disc on the tray.
4 AOPEN/CLOSE button (16)
Opens or closes the disc tray.
5 ./>PREV/NEXT (previous/next) buttons (17)
Press to go to the next chapter or track, or to go back
to the previous chapter or track.
6 TITLE button (20)
Displays the title menu on the TV screen.
7 DVD MENU button (20)
Displays the DVD menu on the TV screen.
Index to Parts and Controls
Rear Panel
AUDIO OUT
DIGITAL OUT
VIDEO OUT
S VIDEO OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL OPTICAL
R
L
Additional Information
1 AUDIO OUT R (right)/L (left) connectors (8, 10)
Connect to the audio input connector on your TV or
receiver (amplifier).
2 DIGITAL OUT COAXIAL connector (10, 12)
Connect to an audio component using a coaxial digital
connecting cord.
3 DIGITAL OUT OPTICAL connector (10, 12)
Connect to an audio component using an optical
digital connecting cord. Take off the cap.
4 VIDEO OUT connector (8)
Connect to the video input connector on your TV or
monitor.
5 S VIDEO OUT connector (8, 10)
Connect to the S video input connector on your TV or
monitor.
6 COMPONENT VIDEO OUT connectors (9)
Connect to a monitor or projector having component
video input connectors (Y, PB/B-Y, PR/R-Y) that
conform to output signals from the player.
64
COMPONENT VIDEO OUT
Y
PB/B-Y PR/R-Y
9
Remote
0
qa
1
2
3
4
5
6
7
8
9
0
qs
qd
qf
qg
qh
qk
ql
w;
wa
ws
wd
1 ZOPEN/CLOSE button (17)
Opens or closes the disc tray.
2 Number buttons
Selects the items or settings.
3 CLEAR button (27, 38)
Press to return to continuous play, etc.
4 ANGLE button (33)
Changes the angles when playing a DVD.
5 AUDIO button (30)
Changes the sound while playing a DVD or VIDEO
CD.
6 PROGRAM button (39)
Displays the “PROGRAM” display on the TV screen.
7 SHUFFLE button (40)
Changes the “SHUFFLE” mode.
8 ./>PREV/NEXT (previous/next) buttons (17)
Press to go to the next chapter or track, or to go back
to the previous chapter or track.
wf
wg
wh
65
Additional Information
qj
/
SEARCH/STEP buttons (18)
While monitoring the picture, keep pressing to locate a
point quickly or press sequentially to play a disc frame
by frame.
HPLAY button (16)
Plays a disc.
TITLE button (20)
Displays the title menu on the TV screen.
DISPLAY button (24)
Displays the Control Menu display on the TV screen
to set or adjust the items.
</M/m/,/ENTER buttons
Selects and executes the items or settings.
TV @/1 (television on/standby) button (53)
Turns on and off the power of the TV.
@/1 (on/standby) button (17)
Press to turn on the player or place it in standby mode
after power is connected by pressing ! on the player.
TV (television)/AV receiver (amplifier) operation
buttons (53)
Controls TVs or AV receivers (amplifiers).
ENTER button
Executes the items or settings.
SUBTITLE button (32)
Changes the subtitles when playing a DVD.
REPEAT button (41)
Changes the “REPEAT” mode.
A-B button (42)
Displays the “A-B REPEAT” display on the TV screen.
TIME/TEXT button (22)
Displays the playing time of the disc, etc., on the front
panel display.
/
SCAN/SLOW buttons (18)
Locate a point quickly while monitoring the picture or
play a disc in slow motion.
xSTOP button (17, 19)
Stops playing a disc.
XPAUSE button (17)
Pauses playing a disc.
DVD MENU button (20)
Displays the DVD menu on the TV screen.
ORETURN button (21, 25)
Press to return to the previously selected screen, etc.
Index
Numerics
D, E
16:9 47
4:3 LETTER BOX 47
4:3 PAN SCAN 47
4:3 WIDE MODE 47
5.1 Channel Surround 12
DIGITAL OUT 52
Digital output 10, 12
Digital Output 52
DIMMER 48
Display
Control Menu display 24
Front panel display 22
Setup Display 43
DOLBY DIGITAL 11, 52
DOWNMIX 52
DTS 53
DVD 4, 16, 60
DVD menu 20
DVD MENU 46
A
A-B REPEAT 41
ADVANCED 35
Angle 32
ANGLE 32
AUDIO 30, 46
AUDIO ATT 51
AUDIO DRC 51
AUDIO SETUP 51
AUTO PLAY 48
F, G
R
Remote 7, 53
REPEAT 40
Resume Play 19
S
Additional Information
S video output 8, 10
Scene 5
SCENE 27
SCREEN SAVER 47
SCREEN SETUP 47
Searching. See Locating.
Setup Display 43
SHUFFLE 39
Shuffle Play 39
Slow-motion Play 18
SUBTITLE 32
H
C
CD 4, 16
Chapter 5, 27, 60
CHAPTER 27
Connecting 8, 10, 12
Continuous play
CD/VIDEO CD 16
DVD 16
Control Menu display 24
CUSTOM PARENTAL
CONTROL 36
CUSTOM SETUP 48
PAN SCAN 47
PARENTAL CONTROL 48
PAUSE MODE 48
PBC functions 21
PBC Playback 21, 60
PRO LOGIC 52
PROGRAM 37
Program Play 37
Fast Forward 18
Fast Reverse 18
Front panel display 22
B
BACKGROUND 47
Batteries 7
P, Q
Handling discs 6
Hooking up 8, 10, 12
I, J, K
Index 5, 27
INDEX 27
T
L, M, N
TIME/TEXT 28, 29
Title 5, 27, 60
TITLE 27
Title menu 20
Track 5, 27, 61
TRACK 27
TRACK SELECTION 51
Troubleshooting 55
TV TYPE 47
LANGUAGE SETUP 46
LETTER BOX 47
Locating
a specific point 18
by watching the TV screen 18
O
On-screen display
Control Menu display 24
Setup Display 43
OSD 46
U
Usable discs 4
V, W, X, Y, Z
VES 33
VIDEO CD 4, 16, 61
66
Sony Corporation
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising