AS-Interface cable plug • with integrated AS

AS-Interface cable plug • with integrated AS
2510/2511
AS-Interface
AS-Interface cable plug
• with integrated AS-Interface
connection
• Quick and robust installation
• Simple commissioning and error
identification with LED status display
Type 2510/2511 ASI can be combined with ...
Type 8032
Type 6012
Type 6213
Type 6519 NAMUR
Sensor
Pilot valve
Solenoid valve
Pneumatic valve
The ASI cable plug consist of a polyamide body with an integrated
slave electronics and a connector configuration according to DIN EN
175301-803* Form C (Typ 2510) or Form A (Typ 2511). These plugs
connect binary elements with the corresponding tag connectors, e.g.,
valves, to the AS-interface. In addition, feedback signals can be
received by the variants with the M12 socket in the cover.
With the M12 connectors, the installation times are quick and the
electrical connection is simple.
Mechanical data
Body material
Body cover
Contact material
Contact distance
Electrical data (Continued)
Polyamide
Polysulphone, translucent
Brass, electro-silver-plated
8 mm with Form C
18 mm with Form A
Electrical data
Operating voltage
max. current
Electronics
Bus-supplied
External supplied
Electrical connection
on cable
device side
M12 socket
Output voltage
Outputs
max. output current
bus supplied
external supply
29.5 ... 31.5 V
acc. to ASI specifications
from the AS-Interface
only 10 mA
300 mA (electronics, valves,
sensors)
80 mA (electronics, sensors)
M12 plug
Cable plug for tag connector
acc. to DIN EN 175301-803*
Form A or C
4-pin for feedback device
24 V ±10 %
short-circuit proof
205 mA, without inputs
125 mA, with inputs
700 mA
* So far DIN 43650
www.burkert.com
The advantages with ASI cable plug
• Robust and quick installation according to the AS-interface
specification.
• LED status displays facilitate commissioning and fault finding.
• Bus supply: Transmission of signals and supply voltage on a
common line.
• External supply: transmission of signals and supply voltage on
separate lines (such as Emergency Stop or elements with high
current consumption).
Page 1/4
Outputs
max. switching power
bus supplied
external supply
Inputs
Input connection
Supply voltage
Sensor
max. sensor current
High signal
Low signal
max. sensor current
5 W, without inputs
3 W, with inputs
15 W
optional
3-wire voltage sensors
PNP
2-wire voltage sensors
24 V ±20 % over ASI
60 mA for 2 sensors
(for example 30 mA for each)
10 V
1.5 mA
6.5 mA
General data
Operational display LED
Watchdog function
Ambient temperature
Soiling level
Protection class
Certification
yellow or green
integrated
0 ... +50 °C
3 acc. to DIN VDE 0110 part 1
IP65
trough AS Internal Association
(no. 32001, 32002)
2510/2511
AS-Interface
Dimensions [mm]
8
Appliance socket, with receptacle for feedback element, with translucent cover
69.6
32.5
45
ø 26
8
3
2
M 12x1
4
34.85
18
Type 2510 Form C
1
18
Type 2511 Form A
LED status display
Display
OUT
LED colour
yellow
BUS
green
IN 1 / IN2
(Inputs LED)
Ext. Power
yellow
green
LED status
off
on
off
on
blinking
off
on
on
Programming data
Information
not switched
switched
Power OFF
OK
Slave Adress 0
not switched
switched
24 V Power supply
Assignment of the data bits
Parameter
I/O configuration
ID code
Coding
B hex (1 output, 2 inputs)
F hex
Preset address
0
Data bit
D3
D2
D1
D0
Page 2/4
Assign
IN1
IN2
OUT
Remarks
Model with acceptance
of feedback elements.
2510/2511
AS-Interface
AS-Interface socket with M12 bus plug
PIN configuration of M12 bus plug
M12 socket for
feedback
elements
4
3
1
2
1
2
3
4
1)
AS-Interface+
0 V 1)
AS-Interface24 V 1)
only for externally supplied appliance sockets
PIN configuration of M12 socket for feedback elements
M12 bus plug
for connection to
the AS-Interface
3
4
2
1
1
2
3
4
+24 V
Sensor 2
0V
Sensor 1
Bus supplied
External supply
without
with
without
with
Item no.
Type 2510
Form C
142
142
142
142
693
692
689
688
Item no.
Type 2511
Form A
•
Receptacle
for feedback
element via
M12 socket
Voltage
Ordering chart (other versions on request)
142
142
142
142
•
All layout diagrams for appliance sockets acc. to
DIN EN 175301-803* Form C or Form A.
The delivery of an AS-Interface appliance socket
includes the seal and the fixing screw.
* So far DIN 43650
695
694
690
691
M12 T-Connector
For the connection of the bus-supplied appliance
socket to the AS-Interface (yellow ribbon cable)
Page 3/4
Item no.
Use
Designation
Ordering charts accessories
787 350
2510/2511
AS-Interface
Item no.
Use
Designation
Ordering charts accessories (Continued)
AS-Interface tap with
2 m round cable
(2x1.5 mm²)
Connection for the AS-Interface ribbon cable via the
round cable (bus-supplied)
784 756
AS-Interface tap with
1.5 m round cable
(5x0.5 mm²)
Connection for the yellow and black AS-Interface
ribbon cable via round cable
784 758
M12 plug with
PG7 screw fitting;
5-pole
Plugs always in connection with one the AS-Interface
taps ordering.
917 116
Other accessories on request:
• Y-shaped distributor for connection of the feedback element (2M8 to M12 and/or M12 to M12) in various lengths
• AS-Interface ribbon cable
• AS-Interface Master, Gateways
• AS-Interface power units
To find your nearest Burkert facility, click on the orange box →
In case of special application conditions,
please consult for advice.
www.burkert.com
We reserve the right to make
technical changes without notice.
Page 4/4
12_2004_A_00891686
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising