VGA Receiver RXURA-SKU
VGA Receiver
www.RCIcustom.com
RXURA-SKU
Features
•
•
•
•
•
•
•
•
Receives audio and video on a single CATx cable
Adjustable cable length compensation to 1000 ft
Digitally controlled adjustment eliminates tweaking pots
Supports resolutions up to 1920x1200 at any refresh rate
Differential signaling eliminates ground loops and noise
Compact & rugged metal enclosure with mounting holes
No software required for setup and use
The RXURA-SKU features RGB skew correction
Description
The RXURA-SKU is a Video and Audio over UTP (Cat5/5e/6) receiver. The RXURA-SKU can receive Video
and Audio from compatible TXUVA transmitters up to 1,000 feet away. The RXURA-SKU supports resolutions up to 1920 x 1200 at 60Hz. The RXURA-SKU can fully compensate for both high-frequency signal
attenuation and color skew in long UTP cables. This product includes universal power supply and is
made in the USA.
This receiver must be used with the TXUVA transmitter
Important note about use with YPbPr signal
Using the standard RXURA-SKU with Component Video can produce excessive brightness and contrast.
Therefore, this unit is not recommended for use with Component Video (YPbPr). Component Video
signal is not as sensitive to twisted-pair skew since the Y signal has all of edge and brightness information. For distances upto 500 ft, a standard lower cost URA can be used with excellent results.
If you would like to have skew compensation for your YPbPr signal, please ask about the model URASKU-CP. The cost is the same and the unit is identical in every way except it is optimized for Component
Video signal levels.
801 North East Street • Frederick, MD 21701 • 301-620-9130 • 800-546-4724 • FAX 301-620-9103
VGA Receiver
RXURA-SKU
www.RCIcustom.com
Specifications
Video Gain:
Video Standards:
Connectors:
Unity
VGA through UXGA, RGBHV, RGBS, RGsB, RsGsBs,
Component Video (bi-/tri-level sync)
(1) RJ-45 Female (CATx Input)
(1) HD15 Female (Video Output)
(1) 3.5mm Female (Audio Output)
(1) 2.1mm Female (Power Input)
Nominal Amplitude: 1 V p-p for Y of component video
0.7 V p-p for RGB and for Pr and Pb of component video
4.0 V to 5.0 V p-p, for TTL Sync signals of RGBHV, RGBS
Impedance:
75 ohms
Resolution:
Up to 1920x1200 non-interlaced at 60Hz
Audio Gain:
Unbalanced output: 0 dB
Skew Compensation: 65 nS
Max Distance:
Up to 1000 feet depending on resolution
Frequency Response: 20hz to 20kHz, +/- 1 dB
Audio Type:
THD + Noise:
Monaural, Simulated Stereo (L+R)
0.2% @ 1kHz, 0.3% @ 20kHz at nominal level
Recommended Cable: CAT 5/5e/6 (shielded or unshielded) for URA-XT and URA-SKU
Power Supply:
Temperature:
Cooling:
100 VAC to 240 VAC, 50-60 Hz, external; 5 VDC, 2A regulated; 2.1mm
Storage: -40 to +158 degF (-40 to +70 degC) / 10% to 90%, non-condensing
Operating: +32 to +122 degF (0 to +50 degC) / 10% to 90%, non-condensing
Convection, vents on each end
Mounting:
Brackets at each end with screw hole provided for Wall or Rack mounting
Dimensions:
1.18" H x 2.75" W x 3.85" D
(30mm H x 70mm W x 98mm D) Depth excludes connectors
Enclosure:
Metal
Weight:
Product - 0.75 lb (0.35 kg)
EMI/EMC:
CE/FCC Class A
Vibration:
MTBF:
Warranty:
ISTA 1A in carton (International Safe Transit Association)
90,000 hours
2 years parts and labor
801 North East Street • Frederick, MD 21701 • 301-620-9130 • 800-546-4724 • FAX 301-620-9103
VGA Receiver
www.RCIcustom.com
RXURA-SKU
Powering up TXUVA with one power supply
• It is important to note that the TXUVA can be powered from the source (through the VGA cable)
without the need to connect an external power source. Almost all VESA compliant sources should
have enough power to run the unit, and there is a power LED indicator on the front of the wall plate
to show the power status.
• The TXUVA comes with a small power supply that can get wired
to the wall plate and connected to the screw terminals on the rear
of the circuit board as shown to the right.
• The wiring to this screw terminal is low voltage and no special
requirements are needed (check with your local wiring code), but
the power supply itself needs AC input so it either needs to be
located outside the wall and wired to the screw terminal, or in an
electrical junction box in the wall or ceiling to meet electrical code.
• Many installers run a separate cable (two wire extension of 20 gauge or thicker) alongside the UTP
cable so the power supply can be located at the remote end where the URA receiver is located.
• It is also is possible to use the 5v power supply that comes with the URA to power both the URA and
the wall plate in the same manner.
To do that, a 2.1mm Power splitter cable would be required as shown below. These are commercially
available.
• We also recommend using commercially available 2.1mm female to screw terminal adapter (as shown
below) to plug to one end of the power splitter cable.
801 North East Street • Frederick, MD 21701 • 301-620-9130 • 800-546-4724 • FAX 301-620-9103
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising