ANGLED CEILING ADAPTER

ANGLED CEILING ADAPTER
ITEM #0805608, 0829276, 0829277
ANGLED CEILING ADAPTER
MODEL #40030, 40295, 40294
Harbor Breeze® is a registered trademark of LF,
LLC. All rights reserved.
ATTACH YOUR RECEIPT HERE
Purchase Date
PACKAGE CONTENTS
PART
C
A
D
B
DESCRIPTION
QUANTITY
A
Ball
1
B
C
D
Mounting Bracket
Canopy
Canopy Cover (preassembled to Canopy [C])
1
1
1
E
Ball Adapter
1
E
HARDWARE CONTENTS (shown actual size)
AA
Set Screw
Qty. 1
BB
Ground Screw
Qty. 1
CC
DD
EE
Ground Wire
(not to scale)
Qty. 1
Pin
Qty. 1
Mounting Bracket Screw
Qty. 4
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING
•
ELECTRICAL SHOCK HAZARD/FIRE HAZARD: Disconnect power before removing or installing parts in fixture. Failure to do so can result in death
or electrical shock.
•
To prevent fire, install in accordance with appropriate electrical codes and regulations.
•
It is extremely important the outlet box is securely attached to the building structure and can support the full weight of the fan. Do NOT use a plastic
outlet box. Ensure the outlet box is clearly marked “Suitable for Fan Support.” If not, it must be replaced with an approved outlet box. Failure to do
so can result in serious injury.
•
Failure to align slot in ball with tab may cause fan to wobble or fall, which could result in serious injury or death.
CAUTION
•
Ceiling angle is not to exceed 45o for 1/2-in. or 3/4-in. downrods.
•
It is imperative you use the hanging bracket and canopy provided with this angled ceiling adapter as the screw holes in the hanging bracket are aligned
to fit specifically with the screw holes in the canopy provided.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is
missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Phillips Screwdriver and Step Ladder
EB1695
1
ASSEMBLY INSTRUCTIONS
Note: This item was designed for use with an existing ceiling fan. It will be necessary to purchase a longer downrod in order to install the fan to a vaulted ceiling.
The parts included with this item will be used instead of similar parts included with your fan.
1.Turn off circuit breakers and wall switch to
the fan supply line leads.
1
DANGER: Failure to disconnect the
power supply prior to installation may
result in serious injury or death.
2.With the mounting bracket (B) resting
inside the canopy (C), partially install two
mounting bracket screws (EE) into the
two holes surrounded by the J-slots in the
canopy (C). Then, remove the mounting
bracket (B) from the canopy (C).
2
B
EE
C
J-slot
3.Using the screws and washers provided
with the outlet box (not included), secure
the mounting bracket (B) to a “Ceiling
Fan Rated” outlet box. The opening of
mounting bracket (B) should open toward
the floor.
3
B
Opening
7a. If using a 3/4-inch diameter
accessory downrod, attach the ground
wire (CC) to the smaller hole in the
accessory downrod using the ground
screw (BB). Then slide the pin (DD)
into the two large holes at the top of the
downrod.
7a
7b. If using a 1/2-in. diameter downrod,
slide the ball adapter (E) onto the
accessory downrod and down into the
center of the ball (A). Then, attach the
ground wire (CC) to the small hole in
the top of the accessory downrod with
the ground screw (BB). Align the large
holes in the ball adapter (E) with the
large holes in the top of the accessory
downrod, then slide pin (DD) through
larger holes in the ball adapter (E) and
downrod.
7b
8. Raise the ball (A) to the top of accessory
downrod, aligning hole in the ball (A)
with set screw hole at top of downrod.
This will allow the pin (DD) to fall into
the proper slot in the top of the ball (A).
Then, secure the ball (A) to the top of
the accessory downrod using the set
screw (AA).
8
BB
DD
Hole
CC
BB
DD
CC
E
A
AA
A
DD
Top view
4.Slide the accessory downrod (sold
separately) into the yoke of the ceiling fan.
Install the accessory downrod according
to the instruction manual included with the
ceiling fan.
4
9. Lift the ball (A) along with the fan into
the opening in the mounting bracket (B).
Align one of the slots in the ball (A) with
tab in the mounting bracket (B).
Accessory
Downrod
DANGER: Failure to align a slot in
the ball (A) with the tab in the mounting
bracket (B) may cause fan to wobble or
fall, which could result in serious injury
or death.
Yoke
5.If using this item on an angled ceiling,
snap out the perforated section of the
canopy cover (D).
5
10. Align the canopy (C) over the
loose mounting bracket screws (EE)
preassembled on the mounting bracket
(B) in Step 2. Then, twist canopy (C) to
lock. Insert two more mounting bracket
screws (EE) into the round holes of the
canopy (C). Tighten all four mounting
bracket screws (EE).
D
6.Slide the canopy (C) of your choice and
the ball (A) onto the accessory downrod.
Note: Ball (A) must be positioned with the
holes near the top of the downrod.
9
B
Slot
A
Tab
10
B
EE
C
6
Hole
A
C
9168 • 101716
2
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising