r115s cartridge replacement 1 2 3 4 6 5 7 1 2 3 4 5 6 7 8

r115s cartridge replacement 1 2 3 4 6 5 7 1 2 3 4 5 6 7 8
R115S CARTRIDGE REPLACEMENT
Kit Contains:
CARTRIDGE REPLACEMENT STEPS
1
3
2
New Cartridge – R115S
Two self tapping 4-40, 5/8” long Phillips
head screws
Instruction sheet
Remove four screws that hold in
the cartridge.
Remove Case
Save two
Tools Required:
#2 Phillips Head Screwdriver
Wire Cutter
Wire Stripper
Low wattage Soldering Iron
Solder
Support microphone
Remove screws (4)
Instructions:
1
Secure base of microphone housing to keep it from rolling or sliding off of work surface.
2
Remove the four Philips screws that hold the front case to the microphone housing.
and set aside.
3
Unscrew the four Phillips screws that hold the black microphone cartridge into the housing. Save two as they
will be used to secure the new cartridge.
4
Carefully withdraw the microphone cartridge taking care not to stretch or break the three wire leads; blue, black
and yellow.
5
Cut the three wires at the base of the cartridge. Discard cartridge. (55SH only)
For Super 55: Unsolder wires at PC board.
6
Holding the wires out and down towards the stem of the microphone, place the Super 55 bracket/cartridge
assembly into the microphone housing. Do not force. Cartridge will only fit if the PC board and solder pads are
facing up and at the bottom of the base.
7
Install two of the screws that held the old cartridge in place in the upper two holes of the bracket. Install the two
longer screws, supplied with the kit, into the lower 2 holes of the bracket. Tighten the screws to hold the bracket
in the housing.
8
Strip off approximately ¼ in of insulation from the end of each wire and tin with solder - 55SH only.
9
Solder each wire to the pad on the circuit board labeled with its corresponding color. Solder Yellow wire to yellow
pad , black to black, and blue to blue (see note).
4
Carefully withdraw cartridge
5
6
Remove the front case
7
Cartridge will only fit if the PC board and solder pads
are facing up and at the bottom of the base.
Install two of the
screws that held the
old cartridge in place
in the upper two holes
of the bracket.
Cut wires at the base of cartridge
(55SH only)
NOTE: When replacing the cartridge in the Super 55 there is no blue wire.
Install the two longer screws, supplied with the kit, into
10
Tuck any excess wire under the bracket.
11
Place the front case half back on the microphone housing with the Shure logo oriented as shown
in illustration.
12
Reinstall and tighten the four Phillips screws that were removed in step two. Return handle to
normal position.
Do not stretch or break these leads
Hold wires out of the way and towards the
handle of microphone.
Place the Super 55 bracket/cartridge assembly into
the microphone housing. Do not force.
the lower 2 holes of the bracket.
CARTRIDGE REPLACEMENT STEPS
8
10
R115S Replacement Cartridge Kit for
Super 55 and 55SH Series II Microphones
11
Tin with solder
Strip off approximately ¼
in of insulation
Replace the front case
Logo must be oriented as shown
Reinstall the four Phillips screws that
were removed
9
Tuck excess wire
under bracket
Solder wire to the pad
Black wire to black pad
Yellow wire to yellow pad
Blue wire to blue pad – when
replacing cartridge in 55SH
Series II microphone
Note: No blue wire in Super 55
microphone
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
©2009 Shure Incorporated
27A12880 (Rev. 1)
Printed in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising