marque: tp-link reference: tpl_tlsf1016d codic: 4076656

marque: tp-link reference: tpl_tlsf1016d codic: 4076656
MARQUE: TP-LINK
REFERENCE: TPL_TLSF1016D
CODIC: 4076656
TL-SF1005D
TL-SF1008D
TL-SF1016D
10/100Mbps Desktop Switch
REV: 1.0.0
1910010004
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice.
is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make
any derivative such as translation, transformation, or adaptation without permission from TPLINK TECHNOLOGIES CO., LTD. Copyright © 2008 TP-LINK TECHNOLOGIES CO., LTD. All
rights reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
SAFETY NOTICES
Cautions
Do not use this product near water, for example, in a wet basement or near a swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock
from lightning.
Package Contents
The following items should be found in your box:
¾
One TL-SF1005D/TL-SF1008D/TL-SF1016D Switch
¾
One Power Adapter
¾
This User Guide
) Note:
Make sure that the box contains the above items. If any of the listed items are damaged or
missing, please contact with your distributor.
CONTENTS
Chapter 1. Introduction of the Product................................................................... 1
1.1 Overview of the Product............................................................................ 1
1.2 Convention................................................................................................ 1
1.3 Features.................................................................................................... 1
Chapter 2. Installation.............................................................................................. 2
2.1 Mounting the Switch on a Desk................................................................. 2
2.2 Power On .................................................................................................. 2
Chapter 3. Identifying External Components......................................................... 3
3.1 Front Panel ............................................................................................... 3
3.2 Rear Panel ................................................................................................ 3
Appendix A: Specifications..................................................................................... 4
Appendix B: Troubleshooting ................................................................................. 5
Chapter 1. Introduction of the Product
Thank you for choosing the TL-SF1005D/TL-SF1008D/TL-SF1016D 10/100Mbps Desktop Switch.
1.1 Overview of the Product
TL-SF1005D/TL-SF1008D/TL-SF1016D
10/100Mbps
Desktop
Switch
provides
5/8/16
10/100Mbps Auto-Negotiation RJ45 ports. All ports support Auto MDI/MDIX function, eliminating
the need for crossover cables or Uplink ports. The Switch is Plug-and-Play and each port can be
used as general ports or Uplink ports and can be simply plugged into a server, a hub, a switch or
a router and so on, using straight cable or crossover cable.
The TL-SF1005D/TL-SF1008D/TL-SF1016D 10/100M Desktop Switch provides you with a lowcost, easy-to-use, high-performance, seamless and standard upgrade to improve your old
network to a 100Mbps network. It will boost your network performance up to full duplex data
transfer. Its wire-speed switching that forwards packets can be as fast as the speed that your
network delivers those packets to them.
1.2 Convention
The Switch or TL-SF1005D/TL-SF1008D/TL-SF1016D mentioned in this User Guide stands for
TL-SF1005D/TL-SF1008D/TL-SF1016D 10/100Mbps Desktop Switch without any explanation.
) Note:
The three devices of TL-SF1005D, TL-SF1008D and TL-SF1016D are sharing this User Guide.
For simplicity, we will take TL-SF1016D for example throughout this Guide,
The differences between them are:
¾
TL-SF1005D Switch with 5 10/100Mbps Auto-Negotiation RJ45 ports.
¾
TL-SF1008D Switch with 8 10/100Mbps Auto-Negotiation RJ45 ports.
¾
TL-SF1016D Switch with 16 10/100Mbps Auto-Negotiation RJ45 ports.
1.3 Features
¾
Complies with IEEE 802.3, IEEE 802.3u standards
¾
5/8/16 10/100Mbps Auto-Negotiation RJ45 ports supporting Auto-MDI/MDIX
¾
Supports IEEE802.3x flow control for Full Duplex mode and backpressure for Half Duplex
mode
¾
Supports MAC address auto-learning and auto-aging
¾
LED indicators for monitoring power, link, activity
1
¾
Plastic case, desktop or wall-mounting design
¾
External Power Adapter supply
Chapter 2.
Installation
2.1 Mounting the Switch on a Desk
To install the Switch, please follow the steps:
1)
You can place the Switch on a flat desk.
2)
Please inspect the Power Adapter carefully and make sure that it is properly connected to a
power source.
3)
Ensure adequate ventilation space around the switch for dissipating heat and air.
) Note:
Please avoid any heavy thing placed on the switch.
2.2 Power On
Powering on the Switch, it will automatically initialize and its LED indicators will respond as
follows:
1)
All of the Link/Act LED indicators will flash momentarily, which represents a resetting of the
system.
2)
The Power LED indicator will light all the time.
) Note:
If the LED indicators don’t respond as described above, please check the power supply and its
connection.
2
Chapter 3. Identifying External Components
This Chapter describes the front panel, rear panel and LED indicators of the Switch.
3.1 Front Panel
Figure 3-1 TL-SF1016D Switch Front Panel
The Switch’s LEDs are located on the front panel.
¾ Power LED:
This indicator will light up when the Switch powers on.
¾ LEDs (1-16):
One LED indicator will light green when a device is connected to the
corresponding port. It flashes when data is being transmitted or received
on the connection.
3.2 Rear Panel
Figure 3-2 TL-SF1016D Switch Rear Panel
The following parts are located on the rear panel:
¾ Power:
The Power socket is where you will connect the power adapter. Please use
the power adapter provided with this TL-SF1016D Switch.
¾ Port (1-16): The TL-SF1016D Switch is equipped with 16 10/100Mbps Auto-Negociation
RJ45 ports where you will connect your network devices. The working
status can be indicated by the corresponding LEDs on the front panel.
Appendix A: Specifications
General
Standards
IEEE802.3 10Base-T, IEEE802.3u 100Base-TX
Topology
Star
Protocol
CSMA/CD
Data Transfer Rate
Network Media(Cable)
Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex)
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)
10Base-T: UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100Base-TX: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
Number of Ports
5/8/16 10/100Mbps Auto-Negotiation RJ45 ports
LED indicators
Power, 10/100Mbps Link/Act
Transfer Method
Store-and-Forward
MAC Address Learning
Automatically learning, automatically aging
Frame Filter Rate
10Base-T: 14880pps/Port
100Base-Tx: 148800pps/Port
10Base-T: 14880pps/Port
Frame Forward Rate
100Base-Tx: 148800pps/Port
Environmental and Physical
Operating Temperature
0℃ ~40℃ (32℉~104℉ )
Storage Temperature
-40℃ ~70℃ (-40℉ ~158℉)
Operating Humidity
10%~90% non-condensing
Storage Humidity
5%~90% non-condensing
4
Appendix B: Troubleshooting
1.
The Power LED is not lit
Check to see if the power cord is connected to the Switch properly, and make sure the
power source is ON.
2.
The Link/Act LED is not lit when a device is connected to the corresponding port
Check to see if the cable connectors are firmly plugged into the Switch and the device, and
verify the connected device is turned on and working well. Make sure the cable is not longer
than 100 meters (328 feet).
5
User Guide
TL-SF1005D
TL-SF1008D
TL-SF1016D
10/100Mbps Desktop Switch
Rev:2.0.1
7106503708
FCC STATEMENT
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2)This device must accept any interference received,
including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this
product may cause radio interference, in which case the
user may be required to take adequate measures.
Package Contents
The following items should be found in your box:
¾
One TL-SF1005D/TL-SF1008D/TL-SF1016D Switch
¾
One Power Adapter
¾
This User Guide
Note:
The wall-mounting screws are not provided. Please
contact your distributor if any of the listed items are
damaged or missing.
1
The Switch mentioned in this User Guide stands
for TL-SF1005D/TL-SF1008D/TL-SF1016D 10/100Mbps
Desktop Switch without any explanation. For Simplicity, we
will take TL-SF1016D for example throughout this Guide.
Refer to the steps below to mount the Switch on a Wall.
1. Drill two holes into the wall. Insert a screw into each
hole and leave a part of its head exposed.
2. Place the two wall-mounting slots over the screws and
slide the Switch down to fasten it.
Note: Without slots on the bottom, TL-SF1005D cannot
be mounted on a wall.
2
The Switch's LEDs are located on the front panel:
LED
Status
Indication
Power
On
The switch is powered on.
Off
No Power Source.
*Please check if the power cord
is connected to the Switch
properly, and make sure the
power is ON.
Ethernet On
LED
The corresponding ethernet port
is connected to a network device.
Flashing Data is being transmitted or received.
Off
No device is connected to the
corresponding port.
*Please check if the cable
connectors are firmly plugged
into the switch and the device,
and verify the connected device
is turned on and working well.
COPYRIGHT & TRADEMARKS
is a registered trademark of TP-LINK
TECHNOLOGIES CO., LTD. Other brands and product
names are trademarks or registered trademarks of their
respective holders.
Copyright © 2011 TP-LINK TECHNOLOGIES CO., LTD.
All rights reserved.
http://www.tp-link.com
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising