Manual - Brightlink Cables
Operation instruction
Thank you for purchasing this product. For optimum performance and safety, please read these instructions
carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric
shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and
extend the life of your equipment.
Operation instruction
Table of Contents
1.
Introduction......................................................................................... ....4
2.
Featur es............................................................................................... ......4
3.
Panel Descriptions................................................................................. ........................4
4.
Remote Control Descriptions ............................................................. ..............................6
5.
Application Diagram.................................................................... ....................................7
6.
Spec ifi cati ons ............. ....................................... ................... ................ .... ...............8
7.
Pa ckage Co ntents ................................................................................ .......8
8.
RS- 2 3 2 Pin As s ig n m e n t . .. . .. . .. ... . .. . .. . .. . .. . .. . .. . ... . .. . .. . .. . .. . .. . .. . ... .. . .. . .. . .. . .. . .. ... . .. . .. . .. . .. .9
9.
DI P f o r ED I D S e t t i n g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
10. G U I c o n t r o l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0
11. RS-232 Commands....................................................................................... ..........................19
12. Warranty Poli cy................................................................................. ...................... 20
Introduction:
Operation instruction
The 4×4 Matrix withIR matrixfor HDMI routes four Hi-Def sources to any four HDTV displays, supporting
R
1080p Full HD up to 4K plus all 3D formats, along withmultichanneldigitalaudio formatssuch as Dolby O
True
R
HD and DTS-HD O
Master Audio . Each source can be routedto any display using the front-panelpush buttons,
IR remotecontrol, and RS-232 interface .
Features:
Supports resolutionsup to 1080p@60HZ,48-bit deep color, 4k@30HZ
Allows any source to be displayed on multipledisplays at the same time
Allows any HDMI display to view any HDMI source at any time
Dolby TrueHD and DTS-HD master audio pass throughHDMI output
Advanced EDID managementfor rapid integrationof sources and displays
Multipleswitchingmode, push-in button,IR remotecontrol,and RS-232 control
Easy installationwithrack-mountingears
Full 3D pass - through.
Compliant HDCP
Panel Descriptions
Front Panel
1. IR receiver window----Receivethe IR from the remotecontrolof SX-MX444-4K2K.
2. Power LED indicator---Indicatethe status of the power for the matrix.
3. HDMI outputselection button1 to 4---Press to select the outputfrom 1 to 4.
4. InputLED indicator---Indicatethe status of the inputfor the matrix.
Operation instruction
Back Panel
1. IR inputs 1 to 4 ---- 3.5mm stereo phone-jack
2. IR outputs 1 to4 ---- 3.5mm stereo phone-jack
3. IR extension receiver input ---- 3.5mm stereo phone-jack
4. Power switcher---- Press to power on/off the matrix
5. HDMI inputs 1 to 4----Connect HDMI sources
6. HDMI outputs 1 to 4----Output for displays, AVR etc.
7. RS232 female port----Connect to the PC using RS232 cable
8. Power port---Use included DC adaptor to power the matrix switcher.
Operation instruction
Remote Control Description
Output and Input select
A. OUTPUT-X select INPUT-Y:
1. Press OUTPUT-X (X means 1 to 4 of outputs)Press INPUT-Y ( Y means 1 to 4 of inputs )
2. Press OUTPUT-X (X means 1 to 4 of outputs) press the left and right arrow buttons to select the input.
B. All outputs select INPUT-Y: Press ALL button in zone OUTPUTPress INPUT-Y button ( Y means 1 to 4 of
inputs ), then INPUT-Y switched to ALL OUTPUTS
C. Mirror all inputs and outputs (Ex. Input 1 to output 1, input 2 to output 2, etc): Press PTP button in Zone
OUTPUT
Operation instruction
EDID Set Up
A. Fixed EDID to INPUT-Y/ALL
Press 1080I/1080P/3D/4KPress 2.0CH/5.1CH/7.1CHINPUT-Y/ALL button in Zone INPUT
B. Copy EDID of OUTPUT-X to INPUT-Y/ALL
Press COPY buttonPress OUTPUT-X buttonPress INPUT-Y/ALL button
C. User defined EDID to INPUT-Y/ALL
Press USER1/USER2 buttonPress INPUT-Y/ALL
NOTE: Pressing button sequence should be finished in 5 seconds, otherwise, operation discarded.
Application Diagram
Specifications:
Bandwidth:
2.97Gbps per color
Video Input Connectors:
4x HDMI Type A, 19-pin, female, locking
Video Output Connectors:
4x HDMI Type A, 19-pin, female, locking
RS-232 serial port:
IR Input ports:
IR Output ports:
Rack-Mountable:
Dimensions (W x H x D):
Shipping Weight:
DB-9, female
5x 3.5mm stereo jack
4x 3.5mm stereo jack
Rack ears included
256mm x 114mm x 43mm , without feet
1.0kg
Operating Temperature:
32°F to 104°F (0°C to 40°C)
Storage Temperature :
-4°F to 140°F (-20°C to 60°C)
Power Supply:
12V/2A DC
Operation instruction
Package Contents:
1.
1x HDMI Martix
2.
1x 12V DC power supply
3.
1x Remote control
4.
4x IR Transmitter,
5.
5x IR Receiver.
6.
1x mounting kit.
7.
1x CD for control software & user manual.
RS-232 Pin Assignment
Remote Control
Matrix
PIN
Assignment
PIN
Assignment
1
NC
1
NC
2
Tx
2
Rx
3
Rx
3
Tx
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
Baud Rate: 57600 bps
Data Bit: 8-bit
Parity: None
Stop Bit: 1-bit
Flow Control: None
Console
Operation instruction
DIP for EDID Setting
[DIP]=0000: HDMI 1080p@60Hz, Audio 2CH PCM
[DIP]=0001: HDMI 1080p@60Hz, Audio 5.1CH PCM/DTS/DOLBY
[DIP]=0010: HDMI 1080p@60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
[DIP]=0011: HDMI 1080i@60Hz, Audio 2CH PCM
[DIP]=0100: HDMI 1080i@60Hz, Audio 5.1CH PCM/DTS/DOLBY
[DIP]=0101: HDMI 1080i@60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
[DIP]=0110: HDMI 1080p@60Hz/3D, Audio 2CH PCM
[DIP]=0111: HDMI 1080p@60Hz/3D, Audio 5.1CH PCM/DTS/DOLBY
[DIP]=1000: HDMI 1080p@60Hz/3D, Audio 7.1CH PCM/DTS/DOLBY/HD
[DIP]=1001: HDMI 4K2K, Audio 2CH PCM
[DIP]=1010: HDMI 4K2K, Audio 5.1CH PCM/DTS/DOLBY
[DIP]=1011: HDMI 4K2K, Audio 7.1CH PCM/DTS/DOLBY/HD
[DIP]=1100: DVI 1280x1024@60Hz, Audio None
[DIP]=1101: DVI 1920x1080@60Hz, Audio None
[DIP]=1110: DVI 1920x1200@60Hz, Audio None
GUI Control
PC System: Microsoft Windows Operation System
Installation
4x4 HDMI Matrix controller is a green software. You just need to copy “4x4 HDMI Matrix Controller vx.x.exe” to
the PC which is used to control the Matrix by RS232 COM or TCP to complete installation.
Preparation
1.
Connect PC and Matrix by RS232 cable
2.
Power up Matrix (It will take about 5 seconds to be ready with “Di” beep sound )
3.
Double click “4x4 HDMI Matrix Controller vx.x.exe” icon to run it
How to control Matrix
Common information
Click to select tab page
1
2
1 COM port connect status
3
4
Operation instruction
2 Control command process status
3 Prompt message display area
4 Date and Time display
“General” page
1
○
6
○
2
○
3
○
7
○
4
○
5
○
1 RS232 COM mode
2 List detected COM ports
3 Click to connect or disconnect PC and Matrix ( Connection will be established automatically before control
commands sending )
4 Click to refresh device status: include device information displayed in
connection status in
5
○
area and Input/output port
6 area.
○
NOTE: Tab pages cannot be changed during control command is processing.
5 To enable or disable Input/output tags displaying when setting buttons on “Setting” page focused
6 Device information display area
Operation instruction
7 Input/output port connection status
“Port Tag” page
1
○
3
○
2
○
4
○
1 Input port tags
2 Click to edit Input port tags
3 Output port tags
4
Click to edit Output port tags
NOTE: Edit boxes are read only, click “Edit” button to pop up window to edit the tags.
One set of Input/output port tags can be set for Matrix device when COM control mode selected.
Edit Input port tags
After action of
②, edit form will pop-up as below:
Operation instruction
Define tags for respective Input port, then devices connect the Input ports can be easily remembered.
Click buttons with “×” caption to delete tag which is no use any more, if tag is still used by any other Input port,
delete action will be discarded.
Edit Output port tags
After action of
④, edit form will pop-up as below:
Define tags for respective Output port, then displays connect the Output ports can be easily remembered.
Click buttons with “×” caption to delete tag which is no use any more, if tag is still used by any other Output port,
delete action will be discarded.
Operation instruction
“Setting” page
5
○
1
○
2
○
6
○
3
○
4
○
7
○
1 LED which displays Input number for respective Output port
2 Click to select Input port for respective Output port
3 Click to select previous or next Input port for respective Output port
4 Display Output from Input with tag information when mouse moves over ② buttons
5 Pre-Setting items: Default is Port to Port
6 Click to edit selected pre-setting item
7 Set selected pre-setting item to Matrix
NOTE: When Change to this “Setting” page, software will try to refresh source selection status of Output port.
Operation instruction
Pop-up tag messages
When “Display Input, Output tags when focus setting buttons” checkbox on “General” page is checked and
Input/output port tag has been defined, tag messages will pop up like as:
Pop-up Menu
When mouse moves over
② setting buttons, and click mouse right button, menu will pop up like as:
All Outputs: All Outputs from same Input
Operation instruction
“1 Output” to “4 Outputs”: Set current Output (where mouse right clicked) and the next x-1 ( x range is from 1 to 4,
set total x Outputs at the same time ) Output(s) from same Input
Port to Port: Output1 from Input1, Output2 from Input2, Output3 from Input3, etc.
Edit selected pre-setting item
After action of
⑥, edit form will pop-up as below:
1
○
3
○
1 Pre-Setting name
2 Set all Output ports from same Input
3 Select Input for respective Output
2
○
Operation instruction
“EDID control” page
1 Set EDID mode for selected Input port or All Input ports, click “Set” button to complete action.
NOTE: When set User1/User2 EDID mode, should Download EDID content to User1 Memory/User2
Memory first. User1/User2 default EDID content is 1080p, Stereo Audio 2.0.
2 Copy EDID from Output port to selected Input port or All Input ports, click “Copy” button to complete
action.
3 Read EDID content from Output port and display in grid, click “Read” button to complete action.
4 Save EDID content which displayed in grid to binary file (file extension is “.bin”)
5 Open EDID binary file and display in grid
6 Download EDID content which displayed in grid to selected Input port or All Input ports, click “Download”
button to complete action. When User1 Memory/User2 Memory selected, download EDID content to
respective memory then User1/User2 EDID mode can be set.
7 EDID content displaying grid
NOTE: EDID content displayed in grid is read only.
8 Click to clear EDID content displayed in grid
Operation instruction
“IR Configuration” page
To enable or disable IR control function. When box checked, IR control function enabled, otherwise, IR control
function disabled. This setting is not memorized. IR control function is always enabled after power up.
“FW upgrade” page
Operation instruction
1 Click to open firmware file (file extension is “.fw”).
2 Firmware upgrade progress
3 Click the button to upgrade firmware.
NOTE: If failure occurs during upgrading firmware process, the following steps SHOULD be done sequentially to
establish next upgrading procedure:
1.
Power down the Matrix
2.
Close the 4x4 HDMI Matrix Controller
3.
Re-power up the Matrix, then wait for 10 seconds to ensure the Matrix is ready
4.
Run 4x4 HDMI Matrix Controller, open firmware file and upgrade again
4 Firmware upgrading messages display
5 Click to clear the messages displayed in the memo box.
Operation instruction
RS-232 Commands
================================================================
HDMI Matrix-4x4 Help Info
FW Version: 1.67
============= System Information Command
?
HELP
STATUS
Print Help Information
Print Help Information
Print System Status And Port Status
============= System Control Command
PON
Power On, System Run On Normal State
POFF
Power Off, System Run On Power Save State
IR ON/OFF
Set System IR Control On Or Off
KEY ON/OFF
Set System KEY Control On Or Off
APM ON/OFF
Set Advanced Process Mode On Or Off
BEEP ON/OFF
Set Onboard Beep On Or Off
RESET
Reset System To Default Setting
(Should Type "Yes" To Confirm, "No" To Discard)
============= Input And Output Port Control Command
OUT xx ON/OFF Set OUTPUT:xx On Or Off
OUT xx FR yy
Set OUTPUT:xx From INPUT:yy
xx=00: Select All OUTPUT Port
xx=[01...04]: Select One OUTPUT Port
yy=[01...04]: Select One INPUT Port
Operation instruction
EDID xx CP yy Set Input:xx EDID Copy From Output:yy
EDID xx DF zz Set Input:xx EDID To Default EDID:zz
xx=00: Select All INPUT Port
xx=[01...04]: Select One INPUT Port
yy=[01...04]: Select One OUTPUT Port
zz=00: HDMI 1080p@60Hz, Audio 2CH PCM
zz=01: HDMI 1080p@60Hz, Audio 5.1CH PCM/DTS/DOLBY
zz=02: HDMI 1080p@60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=03: HDMI 1080i@60Hz, Audio 2CH PCM
zz=04: HDMI 1080i@60Hz, Audio 5.1CH PCM/DTS/DOLBY
zz=05: HDMI 1080i@60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=06: HDMI 1080p@60Hz/3D, Audio 2CH PCM
zz=07: HDMI 1080p@60Hz/3D, Audio 5.1CH PCM/DTS/DOLBY
zz=08: HDMI 1080p@60Hz/3D, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=09: HDMI 4K2K, Audio 2CH PCM
zz=10: HDMI 4K2K, Audio 5.1CH PCM/DTS/DOLBY
zz=11: HDMI 4K2K, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=12: DVI 1280x1024@60Hz, Audio None
zz=13: DVI 1920x1080@60Hz, Audio None
zz=14: DVI 1920x1200@60Hz, Audio None
================================================================
Operation instruction
Safety information
safeguards
To reduce the risk of electric shock, do not expose this product to rain or moisture
PRODUCT SERVICE
1) Damage requiring service: The unit should be serviced by qualified service personnel if:
(a)The DC power supply cord or AC adaptor has been damaged;
(b)Objects or liquids have gotten into the unit;
(c)The unit has been exposed to rain;
(d)The unit does not operate normally or exhibits a marked change in performance;
(e)The unit has been dropped or the cabinet damaged.
2) Servicing Personnel: Do not attempt to service the unit beyond that described in these operating instructions. Refer all
other servicing to authorized servicing personnel.
3) Replacement parts: When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts
that have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other
hazards.
4) Safety check: After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper
working condition.
WARRANTY
If your product does not work properly because of a defect in materials or workmanship, our Company (referred to as "the
warrantor" ) will , for the length of the period indicated as below, (Parts(1)Year ,Labor(90) Days) which starts with the date of
original purchase ("Limited Warranty period"), at its option either(a) repair your product with new or refurbished parts, or (b)
replace it with a new of a refurbished product. The decision to repair or replace will be made by the warrantor.
During the "Labor" Limited Warranty period there will be no charge for labor.
During the "Parts" warranty period, there will be no charge for parts. You must mail-in your product during the warranty
period. This Limited Warranty is extended only to the original purchaser and only covers product purchased as new. A
purchase receipt or other proof of original purchase date is required for Limited Warranty service.
Mail-In Service
When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the original carton. Include a
letter detailing the complaint and provide a day time phone and/or email address where you can be reached.
LIMITED WARRANTY LIMITS AND EXCLUSIONS
1) This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER
normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damages which occurred in
shipment, or failures which are caused by products not supplied by warrantor,or failures which result from
accidents,misuse,abuse,neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments,
misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, or service by
anyone other than a Factory Service center or other Authorized Servicer, or damage that is attributable to acts of God.
2) THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER "LIMITED WARRANTY COVERAGE".THE
WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF
THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRNTY. (As examples, this excludes damages for lost
time, cost of having someone remove or re-install an installed unit if applicable, travel to and from the service, loss of or
damage to media or images, data or other recorded content. The items listed are not exclusive, but are for illustration only.)
3) PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising