AII 24379 Cassette MP3 In dash

AII 24379 Cassette MP3 In dash
www.HandA-Accessories.com
INSTALLATION
INSTRUCTIONS
Attachment Kit :
P/N 08B06-SDA-100
Accessory
Application
CASSETTE/MULTIMEDIA/
IN-DASH CD PLAYER
ATTACHMENT
ACCORD
2- AND 4-DOOR
Publications No.
AII 24379
Issue Date
AUG 2002
BUS cable
Left player bracket
2 Latches
8 Flange nuts, 6 mm
Right player bracket
2 Grommet screws
2 Wire ties
Left player subbracket
3 EPT sealers
Right player subbracket
2 Self-tapping screws, 4 x 12 mm
Player base-bracket
Bus Cable:
P/N 08A31-0E1-010
Player panel
BUS cable
(for navigation equipped model only)
Pocket
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24379 (0208)
08B06-SDA-1000-91
1 of 9
Cassette Player :
P/N 08A03-5E1-000
In-Dash CD Player :
P/N 08A06-3E1-300
Cassette player
In-dash CD changer
4 Washer-screws, 5 x 8 mm
6 Washer-screws, 5 x 8 mm
Washer-screw, 4 x 6 mm
Owner’s Manual
Wire tie
Multimedia Player :
P/N 08A06-4E1-200
Multi media player
Harness clip
4 Washer-screws, 5 x 8 mm
Owner’s Manual
2 of 9
AII 24379 (0208)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
10 mm Combination wrench
Ratchet
10 mm Socket
File
Utility knife
Scissors
Shop towel
Hook tool
Masking tape
Tape measure
•
Gently pry up on the trim ring to release the six
clips.
•
Unplug the two seat heater connectors
(if equipped), and remove the trim ring.
CLIPS (2)
CLIPS (4)
INSTALLATION
TRIM
RING
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your car. These procedures should not
be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons.
2.
Disconnect the negative cable from the battery.
3.
Remove the trim ring.
2206041K
A/T Model
M/T Model
•
SEAT HEATER
CONNECTORS
(If equipped)
Squeeze the plastic clip and pull down on the
shift boot. Remove the shift knob by turning it
counterclockwise.
•
Gently pry up on the trim ring to release the
six clips.
•
Unplug the two seat heater connectors
(if equipped), and remove the trim ring.
CLIPS (4)
CLIPS (2)
SHIFT
KNOB
PLASTIC
CLIP
TRIM
RING
SHIFT BOOT 2206031K
SEAT HEATER
CONNECTOR
(If equipped)
2206112K
TRIM RING
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24379 (0208)
3 of 9
4.
Remove the dashboard center holder:
5.
Remove the pocket:
•
Open the coin pocket lid and remove the coin
pocket.
•
Apply masking tape to the edge of the center
panel.
•
Remove the two self-tapping screws.
•
Remove the two self-tapping screws.
•
Gently pull out on the dashboard center holder
to release the two retaining clips, unplug the
vehicle connector, and remove the center
holder.
•
Push in on the bottom of the pocket, then pull
out on the top by inserting the end of a hook
tool between the pocket and center panel, and
pull it out toward you to release the two
retaining clips.
COIN
POCKET
LID
DASHBOARD
CENTER HOLDER
CENTER
PANEL
HOOK TOOL
SELF-TAPPING
SCREW
(Reuse.)
RETAINING
CLIPS (2)
MASKING
TAPE
LID
Push
POCKET
CLIPS (2)
VEHICLE
CONNECTOR
SELF-TAPPING
SCREW (Reuse.)
2206061K
With Ashtray
6.
•
Open the lid and remove the ashtray.
•
Remove the two-self-tapping screws.
•
Gently pull out on the two retaining clips,
unplug the cigarette lighter harness connector,
vehicle connector, illumination bulb, and
remove the center holder.
ASHTRAY
2206073K
Remove the right and left inner covers (one hook
and one clip for each cover).
CLIP
LEFT INNER
COVER
DASHBOARD
CENTER
HOLDER
RIGHT INNER
COVER
SELF-TAPPING
SCREW (Reuse.)
ILLUMINATION
BULB
HOOK
POCKET
OPENING
CIGARETTE
LIGHTER
HARNESS
CONNECTOR
RETAINING
CLIPS (2)
2226010K
VEHICLE
CONNECTOR
2730010K
4 of 9
AII 24379 (0208)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
Installing the Player
7.
9.
Remove the vehicle harness clip from the vehicle
frame, and move it out of the way.
PLAYER BASEBRACKET
VEHICLE
FRAME
Insert the studs of the left and right player subbrackets into the holes in the vehicle frame, then
install one 6 mm flange nut on the end of each
stud while pushing each sub bracket upward.
VEHICLE
FRAME
VEHICLE
HARNESS
CLIP
(Remove.)
6 mm FLANGE NUT
6 mm
FLANGE
NUT
VEHICLE
FRAME
VEHICLE
FRAME
6 mm
FLANGE
NUT
VEHICLE HARNESS CLIP
(Insert into the hole of the
player base-bracket.)
8.
LEFT PLAYER
SUBBRACKET
2306011T
RIGHT PLAYER
SUBBRACKET
Insert the studs from the player base-bracket into
the holes in the vehicle frame from the back, then
install the two 6 mm flange nuts while holding the
bracket firmly against the vehicle frame. Insert the
harness clip (removed in step 7) into the hole in
the player base-bracket.
2306021T
10. If you are installing an in-dash CD player, remove
the shipping bracket.
SHIPPING
BRACKET
IN-DASH
CD PLAYER
2506020T
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24379 (0208)
5 of 9
14. Plug the BUS cable to the player.
11. Get the pocket. Using a utility knife, cut the two
lugs off from the pocket.
Without Navigation System
Cassette Player
LUG
(Cut off.)
•
Make loops in the BUS cable and secure it
with one wire tie, so that the distance between
the ends of the cable connectors are 200 mm.
Plug the BUS cable connector into the
cassette player connector.
CASSETTE
PLAYER
LUG
BUS CABLE
CONNECTOR
2529041T
POCKET
BUS CABLE
12. Install the one latch to the left and right player
brackets.
WIRE TIE
200 mm
1 mm
1 mm
LATCH
BUS CABLE
CONNECTOR
2306051T
LATCH
LATCH
Multimedia Player
LATCH
LEFT PLAYER
BRACKET
PLAYER
•
5 x 8 mm
WASHERSCREWS (4)
POCKET RIGHT PLAYER
4 x 8 mm
BRACKET
SELF-TAPPING
4 x 8 mm
SCREW
SELF-TAPPING
SCREW
Make loops in the BUS cable and secure it
with one wire tie, so that the distance between
the ends of the cable connectors are 200 mm.
Plug the BUS cable connector into the
multimedia player connector.
MULTIMEDIA
PLAYER
2306031T
13. Position the left and right player brackets on the
player and pocket, and install four 5 x 8 mm
washer-screws, and two 4 x 8 mm self-tapping
screws.
WIRE TIE
BUS CABLE
CONNECTOR
BUS
CABLE
200 mm
BUS CABLE
CONNECTOR
2306061T
6 of 9
AII 24379 (0208)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
In-Dash CD Player
•
•
Cassette Player
Make loops in the BUS cable and secure it
with one wire tie, so that the distance between
the ends of the cable connectors are 180 mm.
Plug the BUS cable connector into the
connector from the in-dash CD player.
CASSETTE
PLAYER
BUS CABLE
CONNECTOR
After connecting, secure the connectors to the
rear of the in-dash player with one wire tie
from in the in-dash CD player kit.
WIRE TIE
(Supplied with
player kit.)
IN-DASH
CD PLAYER
BUS CABLE
(Sold separately)
2306090T
Multimedia Player
MULTIMEDIA
PLAYER
BUS CABLE
CONNECTOR
WIRE TIE
BUS CABLE
180 mm
BUS CABLE
CONNECTOR
2306070T
BUS CABLE
CONNECTOR
With Navigation System
•
BUS CABLE
(Sold separately)
Remove the tape that secures the vehicle
harness to the upper left pocket opening, and
pull the harness out through the pocket
opening.
2306100T
VEHICLE
CONNECTOR
POCKET
OPENING
TAPE
(Remove.)
2306080T
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24379 (0208)
7 of 9
In-Dash CD Player
•
Secure the connectors to the rear of the indash CD player with one wire tie from in the indash CD player kit.
16. Plug the BUS cable connector into the vehicle
connector.
With Navigation System
•
Wrap the plugged connectors with one EPT
sealer.
IN-DASH CD
PLAYER
VEHICLE
CONNECTOR
(With navigation
system)
BUS CABLE
CONNECTOR
(With
navigation
system.)
IN-DASH CD
CHANGER
CONNECTOR
BUS CABLE
(Sold
separately)
BUS CABLE
CONNECTOR
(Without
navigation
system)
LEFT PLAYER
BRACKET
LEFT PLAYER
SUBBRACKET
WIRE TIE
(Supplied with
player kit)
BUS CABLE
CONNECTOR
VEHICLE CONNECTOR
(Without navigation
system)
2306110T
15. To protect the center panel, attach the masking
tape to the panel in the area shown.
6 mm
FLANGE
NUT
CENTER
PANEL
MASKING
TAPE
RIGHT
PLAYER
BRACKET
PLAYER BASEBRACKET
2306121T
RIGHT PLAYER
SUBBRACKET
17. Insert the studs of the left and right player
subbrackets and player base-bracket into the
holes in the left and right player brackets, then
install one 6 mm flange nut on the end of each
stud.
18. Attach two grommet screws to the player panel in
the square holes shown.
PLAYER
PANEL
2506010T
GROMMET
SCREW
8 of 9
AII 24379 (0208)
2306131T
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
19. Measure and cut one EPT sealer in three pieces
using scissors.
EPT SEALER
(Cut off the
marked area.)
22. Check that all wire harnesses are routed properly
and all connectors are plugged in.
23. Reconnect the negative cable to the battery.
PLAYER
PANEL
24. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
25. Set the clock.
26. Check the operation of the player according to the
its Owner’s Manual.
27. Put the player Owner’s Manual in the glove box.
28. Reinstall all removed parts.
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
8 mm
29. Start the engine. Push down fully on the driver’s
window switch until the window is open.
8 mm
EPT SEALER
2612010T
30. Pull up on the driver’s window switch to close the
window completely, then hold the switch for 2
seconds.
31. Test the driver's window AUTO function.
20. Clean the player panel with isopropyl alcohol
where the EPT sealers will attach. Attach the EPT
sealer to the player panel and cut off the excess
area from the player panel.
21. Insert the player panel clips into their latches, and
attach the player panel to the instrument panel
with the two self-tapping screws you removed in
step 5. Remove the masking tape.
CLIP
LATCH
PLAYER
PANEL
SELF TAPPING
SCREW
(Reused)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
2306141T
AII 24379 (0208)
9 of 9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising