Configuration Sheets

Configuration Sheets
PRIMERGY BX620 S4 Server Blade Configuration Sheets
About this manual
A Hardware Configuration Sheet
Use this form to record the hardware configuration of your server.
B
BIOS Setup Utility Settings Sheet
Use this form to record the BIOS settings of your server.
C
RAID Configuration Sheet
Use this form to record the logical drive definitions of RAID configuration (Array
configuration).
D
Design Sheet
Use this form to record the software settings.
E
Accident Sheet
Use this form to record any failures that occur in your server.
1
Abbreviations
The following expressions and abbreviations are used throughout this manual.
Expressions and abbreviations
Product names
PRIMERGY BX600
This server, or server
(Refers to the entire blade server.)
PRIMERGY BX600 S3 Blade Server System Unit
Chassis
PRIMERGY BX620 S4 Server Blade
Server blade
Microsoft® Windows Server® 2003 R2, Standard Edition
Windows Server 2003 R2,
Standard Edition
Microsoft® Windows Server® 2003 R2, Enterprise Edition
Windows Server 2003 R2,
Enterprise Edition
Microsoft® Windows Server® 2003 , Enterprise Edition
Windows Server 2003 ,
Enterprise Edition
Microsoft® Windows Server® 2003, Standard Edition
Windows Server 2003, Standard
Edition
Microsoft® Windows Server® 2003 R2, Standard x64 Edition
Windows Server 2003 R2,
Standard x64 Edition
Microsoft® Windows Server® 2003 R2 , Enterprise x64 Edition
Windows Server 2003 R2,
Enterprise x64 Edition
Microsoft® Windows Server® 2003, Standard x64 Edition
Windows Server 2003, Standard
x64 Edition
Microsoft® Windows Server® 2003 , Enterprise x64 Edition
Windows Server 2003 ,
Enterprise x64 Edition
Microsoft® Windows® 2000 Server
Windows 2000 Server
Microsoft® Windows® 2000 Advanced Server
Windows 2000 Advanced Server
Windows 2003
Windows 2000
Microsoft® Windows Server® 2003 Service Pack
SP
Microsoft® Windows® 2000 Service Pack
■Trademarks
Microsoft, Windows, MS, Windows Server are registered trademarks of the Microsoft Corporation in the USA and other
countries.
Intel, Xeon, Celeron and Pentium are registered trademarks or trademarks of Intel Corporation or its subsidiaries in the
USA and other countries.
All other hardware and software names used are trademarks or registered trademarks of their respective manufacturers.
Other product names are copyrights of their respective manufacturers.
All Rights Reserved, Copyright© FUJITSU LIMITED 2008
2
Contents
A Hardware Configuration Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
B BIOS Setup Utility Settings Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B.1 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B.2 Advanced Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
B.3 Security Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
B.4 Server Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
B.5 Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
C RAID Configuration Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
C.1 Integrated Mirroring SAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
D Design Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
D.1 RAID and Disk Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
D.2 OS Install Wizard (Windows 2003) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
D.3 Application Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
E Accident Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3
A Hardware Configuration Sheet
A Hardware Configuration Sheet
Use this form to record the hardware configuration and various settings of your serv
Put a check mark in parentheses of your server settings.
If you use the new supported product of this server which is not mentioned here,
please note the information on the empty space.
Installation slot of chassis (
)
■ CPU
Installation CPU
Installed number
( ) Processor Xeon E5205 (1.86GHz/6MB)
( ) Processor Xeon X5260 (3.33GHz/6MB)
( ) Processor Xeon E5405 (2GHz/12MB)
( ) Processor Xeon E5420 (2.5GHz/12MB)
( ) Processor Xeon X5460 (3.16GHz/12MB)
( ) Processor Xeon 5148 (2.33GHz/4MB)
(
) 1*
(
)2
( ) Processor Xeon L5320 (1.86GHz/2x4MB)
( ) Processor Xeon L5410 (2.33GHz/12MB)
( )
( )
*)CPU is installed in socket 1 for all models.
■ Memory
Installation memory
Installation slot
Memory slot 1
(*) 512MB ( ) 1GB ( ) 2GB ( ) 4GB
Memory slot 2
(*) 512MB ( ) 1GB ( ) 2GB ( ) 4GB
Memory slot 3
(*) 512MB ( ) 1GB ( ) 2GB ( ) 4GB
Memory slot 4
(*) 512MB ( ) 1GB ( ) 2GB ( ) 4GB
Memory slot 5
(*) 512MB ( ) 1GB ( ) 2GB ( ) 4GB
Memory slot 6
(*) 512MB ( ) 1GB ( ) 2GB ( ) 4GB
Memory slot 7
(*) 512MB ( ) 1GB ( ) 2GB ( ) 4GB
Memory slot 8
(*) 512MB ( ) 1GB ( ) 2GB ( ) 4GB
*: 512MB is installed in memory slot 1 and 2 for all models
(except when custom made service is used).
■ Hard disk
Installation internal hard disk units
Installed position
Bay 1
( ) 73.4GB/10Krpm ( ) 73.4GB/15Krpm ( ) 146.8GB/10Krpm
Bay 2
( ) 73.4GB/10Krpm ( ) 73.4GB/15Krpm ( ) 146.8GB/10Krpm
■ Expansion board
Installed expansion board
(
(
(
(
)
)
)
)
2Gbit/s FC I/O module (PG-FCD102)
4Gbit/s FC I/O module (PG-FCD201)
1Gbit/s LAN I/O module (PG-LND201)
________________________________________________
■ Expansion card
Installed expansion card
(
(
(
(
(
(
)
)
)
)
)
)
Expansion slot Module (PGBCS103)
Expansion slot Module (PGBCS104)
SCSI card (PG-1301L)
LAN card (PG-2861L)
________________________________________________
________________________________________________
4
B.1 Main menu
B BIOS Setup Utility Settings Sheet
Use this form to record the settings of the BIOS Setup Utility in your server.
Print and record the following chart depending on your number of server blades.
When the settings have not been changed since purchase, check the "( ) Settings at
time of purchase are not changed".
The settings for the framed items in the "Settings at time of purchase"can be changed.
When a setting is changed, check the bracket in the "Setting".
The items in shaded regions cannot be changed.
BIOS Setup Utility is started by the following procedures.
When the message below is displayed on the screen during POST, press the [F2] key. After POST,
BIOS Setup Utility main menu appears.
Press F2 to run Setup
Press F12 for BBS POPUP
If the system has started before the BIOS Setup Utility starts, press [Ctrl] + [Alt] + [Del] keys
to restart the system.
B.1 Main menu
( ) The initial values have been unchanged.
Parameters
Settings at time of
purchase
Setting
System Overview
AMIBIOS
Version
nn.nn.nn
Displays the AMI BIOS version.
Build Date
MM/DD/YY
Displays the date that the AMI BIOS is
built.
BIOS Version
nnnn
Displays the BIOS version.
BMC F/W Version
nnnn
Displays the BMC F/W version.
System Time *1
HH:MM:SS
Display/Enter current time.
System Date *1
*** MM/DD/YYYY
Display/Enter current date.
Sync RTC with Mgmt, Blade
Size
Enabled
nnnnMB
( )Disabled
Displays the size of the installed
*1:This item can be entered when [Sync RTC with Mgmt. Blade] is set to [Disabled].
5
B BIOS Setup Utility Settings Sheet
B.2 Advanced menu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
Advanced Settings
Reset Configuration Data
No
( )Yes
> Peripheral Configuration
To ■ Peripheral Configuration submenu
> PCI Configuration
To ■ PCI Configuration submenu
> CPU Configuration
To ■ CPU onfiguration submenu
■ Peripheral Configuration submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
Peripheral Configuration
Serial 1
Serial Port1 Address
3F8/IRQ4
> USB Configuration
( )Disabled ( )2F8/IRQ3 ( )3E8/IRQ4
( )2E8/IRQ3
To ■ USB Configuration submenu
■ USB Configuration submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
USB Configuration
Module Version
X.XX.X-XX.X
Displays the USB code version of the
AMI BIOS.
None
Displays the number of the connected
USB devices .
USB Devices Enabled :
USB Functions
4 USB Ports
( )Disabled
USB 2.0 Controller
Enabled
( )Disabled
Legacy USB Support
Auto
( )Disabled ( )Enabled
>USB Mass Storage Device Configuration*1
To ■ USB Mass Storage Device
Configuration submenu
*1: This is item appears when the USB device is connected.
6
B.2 Advanced menu
■USB Mass Storage Device Configuration submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
USB Mass Storage Device Configuration
USB Mass Storage Reset Delay *1
20Sec
( )10Sec ( )30Sec ( )40Sec
Device #1 *1
XXXXXXXXX
Displays the connected USB device.
Emulation Type *1
Auto
( )Floppy ( )Forced FDD ( )Hard Disk
( )CDROM
Displays the connected USB device.
Device #2 *1
XXXXXXXXX
Emulation Type *1
Auto
Device #3 *1
XXXXXXXXX
Emulation Type *1
Auto
Device #4 *1
XXXXXXXXX
Emulation Type *1
Auto
( )Floppy ( )Forced FDD ( )Hard Disk
( )CDROM
Displays the connected USB device.
( )Floppy ( )Forced FDD ( )Hard Disk
( )CDROM
Displays the connected USB device.
( )Floppy ( )Forced FDD ( )Hard Disk
( )CDROM
*1:This item appears for the number of the connected USB devices .
■ PCI Configuration submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
PCI Configuration
Onboard Disk OPROM
Enabled
( )Disabled
Onboard LAN 1 OPROM
Enabled
( )Disabled
Onboard LAN 2 OPROM
Disabled
( )Enabled
Onboard LAN 3 OPROM
Disabled
( )Enabled
Onboard LAN 4 OPROM
Disabled
( )Enabled
Onboard LAN 5 OPROM
Disabled
( )Enabled
Onboard LAN 6 OPROM
Disabled
( )Enabled
PCI slot OPROM
Disabled
( )Enabled
Daughter Board OPROM
Disabled
( )Enabled
7
B BIOS Setup Utility Settings Sheet
■ CPU Configuration submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
Configure Advanced CPU settings
Module Version:XX.XX
Displays the CPU code version of the
AMI BIOS.
C1E Support *1
Disabled
( )Enabled
Hardware Prefetcher
Enabled
( )Disabled
Adjacent Cache Line Prefetch
Enabled
( )Disabled
Vanderpool Technology *1
Disabled
( )Enabled
Execute Disable Bit
Disabled
( )Enabled
Intel(R) SpeedStep(tm) tech. *1
Disabled
Intel(R) C-STATE tech.
Disabled
( )Maximum Speed ( )Minimum Speed
( )Automatic
( )Enabled
*1: There is the case that is not displayed by a kind of deployment CPU.
B.3 Security menu
( ) Settings at time of purchase are not changed
Parameters
Setting
Settings at time of
purchase
Security Settings
Supervisor Password
Not Installed
Displays whether the Supervisor
Password is set or not.
User Password
Not Installed
Displays whether the User Password is
set or not.
Change Supervisor Password
Set a Supervisor Password.
Change User Password
Set a User Password.
Clear User Password *1
Pressing the [Enter] key will delete the
User Password.
Password Check *2
Setup
( )Always
Supervisor Password Lock *2
Standard
( )Extended
*1:This item appears when [User Password] is specified.
*2:This item appears when [Supervisor Password] or [User Password] is specified.
8
B.4 Server menu
B.4 Server menu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
Server Configuration
Post Errors
Enabled
( )Disabled
> ASR&R
To ■ ASR&R submenu
> CPU Status
To ■ CPU Status submenu
> Memory Status
To ■ Memory Status submenu
> Console Redirection
To ■ Console Redirection submenu
> System Information
To ■ System Information submenu
■ ASR&R submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
ASR&R
OS Boot Watchdog Timer
Disabled
( )Enabled
Timer Count Down Value *1
10 Minutes
( )2 Minutes ( )5 Minutes
( )15 Minutes ( )20 Minutes
( )30 Minutes ( )60 Minutes
( )100 Minutes
Timer Count Action *1
Reset
( )No Action ( )Power Off
( )Power Cycle
Boot Retry Counter
Retry 3 Times
(
(
(
(
ASR&R Boot Delay(Minute)
2
(
After Power Failure
Last State
( )Stay Off ( )Power On
)No Retry ( )Retry 1 Time
)Retry 2 Times ( )Retry 4 Times
)Retry 5 Times ( )Retry 6 Times
)Retry 7 Times
*1:This item appears when [OS Boot Watchdog Timer] is set to [Enabled].
9
) Enter a number 0 to 30
B BIOS Setup Utility Settings Sheet
■ CPU Status submenu
( ) Settings at time of purchase are not changed
Parameters
Setting
Settings at time of
purchase
CPU Status
CPU1 Status:
Enabled
( )Disabled ( )Failed*1 ( )Empty*2
CPU2 Status:
Enabled
( )Disabled ( )Failed*1 ( )Empty*2
*1: This setting appears when CPU IERR occurs . Can be changed to [Enabled] only.
*2: This setting appears when CPU is not installed.
■ Memory Status submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
Memory Status
Memory Scrubbing
Enabled
( )Disabled
Memory Mirror
Disabled
( )Mirror
DIMM 1,2
Enabled
( )Disabled
DIMM 3,4
Enabled
( )Disabled
DIMM 5,6
Enabled
( )Disabled
DIMM 7,8
Enabled
( )Disabled
■ Console Redirection submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
Configure Remote Access type and Parameters
Com Port Address
On-board COM A
( )Disabled
Protocol
ANSI
( )VT100 ( )VT-UTF8 ( )VT100+
Flow Control
XON/XOFF
Mode
Standard
( )Enhanced
10
B.5 Boot menu
■ System Information submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
System Information
Manufacturer:
****
Displays the name of the installed CPU
vendor.
Brand String :
**** **** *** ***
Displays the installed CPU name and
frequency.
Frequency
:
n.nnGHz
Displays the CPU frequency.
FSB Speed
:
nnnMHz
Displays the FSB speed.
Stepping
:
***
Displays the CPU stepping.
Cache L1
:
nn KB
Displays the CPU L1 cache.
Cache L2
:
nnnn KB
Displays the CPU L2 cache.
On Board LAN1 Mac Address:
nn:nn:nn:nn:nn:nn
Displays the MAC address of Onboard
LAN1.
On Board LAN2 Mac Address:
nn:nn:nn:nn:nn:nn
Displays the MAC address of Onboard
LAN2.
On Board LAN3 Mac Address:
nn:nn:nn:nn:nn:nn
Displays the MAC address of Onboard
LAN3.
On Board LAN4 Mac Address:
nn:nn:nn:nn:nn:nn
Displays the MAC address of Onboard
LAN4.
On Board LAN5 Mac Address:
nn:nn:nn:nn:nn:nn
Displays the MAC address of Onboard
LAN5.
On Board LAN6 Mac Address:
nn:nn:nn:nn:nn:nn
Displays the MAC address of Onboard
LAN6.
B.5 Boot menu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Setting
Boot Settings
Bootup Num-Lock
On
(
)Off
> Boot Device Priority
To ■ Boot Device Priority submenu
> Hard Disk Drives *1
To ■ Hard Disk Drives submenu
> Removable Drives *1
To ■ Removable Drives submenu
> CD/DVD Drives *1
To ■ CD/DVD Drives submenu
*1:This item appears when a device is connected.
11
B BIOS Setup Utility Settings Sheet
■ Boot Device Priority submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Boot Device Priority
Setting
(Fill in Boot priority)
1st Boot Device
USB:Y-E USB FDU
(
)USB:Y-E USB FDU
2nd Boot Device
USB:GENERIC CDR***
(
)USB: Virtual Floppy *1
3rd Boot Device
SCSI:#C40 ID00 LUN
(
)USB:GENERIC CDR***
4th Boot Device
Network:MBA v*.*.*
(
)USB:USB*2
5th Boot Device
Network:MBA v*.*.*
(
)SCSI:#C40 ID00 LUN
(
)SCSI:#C40 ID01 LUN
(
)Network:MBA v*.*.*
(
)Network:MBA v*.*.*
(
)Other:______________________
※Device name set as the [1st Device] in each submenu (Hard Disk Drives, Removable Drives,
CD/DVD Drives ) appears in the Setting.
*1:This item appears when an emulation-connected floppy disk drive in the client computer is
connected via an advanced KVM module.
*2:This item appears when an emulation-connected CD-ROM drive in the client computer is connected
via an advanced KVM module.
■ Hard Disk Drives submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Hard Disk Drives
Setting
(Fill in Boot priority)
1st Device *1
SCSI:#C40 ID00 LUN
(
)Disabled (
)SCSI:#C40 ID01 LUN
2nd Device *1
SCSI:#C40 ID01 LUN
(
)Disabled (
)SCSI:#C40 ID00 LUN
*1:This item appears for the number of the connected devices .
12
B.5 Boot menu
■ Removable Drives submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
Removable Drives
Setting
(Fill in Boot priority)
1st Device*1
USB:Y-E USB FDU
(
)Disabled (
)USB: Virtual Floppy *2
2nd Device*1
USB: Virtual Floppy *2
(
)Disabled (
)USB:Y-E USB FDU
*1:This item appears for the number of the connected devices.
*2:This item appears when an emulation-connected floppy disk drive in the client computer is
connected via an advanced KVM module.
■ CD/DVD Drives submenu
( ) Settings at time of purchase are not changed
Parameters
Settings at time of
purchase
CD/DVD Drives
1st Device *1
2nd Device *1
Setting
(Fill in Boot priority)
USB:GENERIC CDR***
(
)Disabled (
USB:USB *2
(
(
)Disabled
)USB:GENERIC CDR***
)USB:USB *2
*1:This item appears for the number of the connected devices.
*2:This item appears when an emulation-connected floppy disk drive in the client computer is
connected via an advanced KVM module.
13
C RAID Configuration Sheet
C RAID Configuration Sheet
Use this form to record the definitions of the disk groups (or the physical packs) and
the logical drives in the RAID configuration (array configuration).
C.1 Integrated Mirroring SAS
■Content of definition of the Logical Drive
Installation HDD slot/bay
HDD model name
HDD capacity
Logical drive capacity
(e.g.)
Bay 1
PG-HDB75A
73.4GB
34464 MB
(e.g.)
Bay 2
PG-HDB75A
73.4GB
34464 MB
Bay 1
Bay 2
14
D.1 RAID and Disk Wizard
D Design Sheet
When setting up the server using ServerStart, set the default values in advance to
ensure setup is performed smoothly.
D.1
RAID and Disk Wizard
Parameters
Setting
( ) Use the existing RAID configuration
(Select even if RAID configuration is
unnecessary)
( ) Create the RAID configuration
(Delete all existing RAID configuration)
( ) RAID
( ) SCSI
( ) Fibrechannel ( ) IDE
Controller
When you select "RAID" with controller's type
Configure RAID
Existing RAID Array
Controller Vendor
Controller Number
Configure
RAID :
Manually
( ) Automatically
( ) Manually
( ) Delete Existing RAID Array
RAID Level
Number of Disks
Disk Make copies when installing multiple disks .
Partition Make copies when more sheets are needed.
Volume label
File system
( ) NTFS ( ) FAT
Partition size
( ) Aut setting
Quick format
( ) Execute
Partition Usage
( ) Boot
15
( ) MB
( ) Do not execute
( ) OS ( ) Data
D Design Sheet
D.2 OS Install Wizard (Windows 2003)
Parameters
Setting
Install Windows 2003
Regional settings
(with keyboard layout)
( ) Use the default regional settings for the Windows -Version you are
installing
( ) Select here (
)
Password for Administrator
account
Computer Identification
When selecting Windows Server 2003/R2 to install
( ) Windows Server 2003, Standard Edition
( ) Windows Server 2003, Enterprise Edition
( ) Windows Server 2003 R2, Standard Edition
( ) Windows Server 2003 R2, Enterprise Edition
Operating System Type
Windows Server 2003 x64/R2 to install
( ) Windows Server 2003, Standard x64 Edition
( ) Windows Server 2003, Enterprise x64 Edition
( ) Windows Server 2003 R2, Standard x64 Edition
( ) Windows Server 2003 R2, Enterprise x64 Edition
ServicePack (SP)
License Mode
(
(
(
(
(
)
)
)
)
)
without integrated Service Pack
with integrated Service Pack1
with integrated Service Pack2
per Seat
per Server
User permitted
will participate in
(Only when concurrent users are selected)
( ) a work group
( ) a domain
Workgroup or Domain Name
User account to create computer account (only when Domain is selected)
User account
(Default - MYUSERGROUP)
Password
( ) Operating system source media in Available in local CD-ROM drive
( ) Operating system source media in Available on a remote share
when installing OS from remote share
Remote Source Path
Remote Username
Installation method
Remote Password
To install Windows Server
2003 R2 Components
( ) Install Windows Server 2003 R2 Components
( ) R2 Components source media is available in local CD-ROM drive
( ) R2 Components source media is available on a remote share
When you install it from a remote share
Remote Source
Remote Username
Reote Password
(continued)
Installation method
16
D.2 OS Install Wizard (Windows 2003)
Parameters
Setting
Installation Directory and Time zone
(Default -(GMT+01:00) Amsterdam, Berlin,
Bern, Rome, Stockholm, Vienna)
Time Zone
Installation Drive
( ) Use default
When selecting drive name
( ) C: ( ) D: ( ) E: ( ) F: ( ) G: ( ) H: ( ) I: ( ) J:
( ) K: ( ) L: ( ) M: ( ) N: ( ) O: ( ) P: ( ) Q: ( ) R:
( ) S: ( ) T: ( ) U: ( ) V: ( ) W: ( ) X: ( ) Y: ( ) Z:
Installation Directory
( ) Use default
( ) Drive Letter
( ) Prompt User
( ) Specify now
Installation destination
(Default - \winnt)
User Name
User Name
Organization
Computer Name
Product-ID
( )
―
―
―
―
Display settings
Resolution
( ) 640 * 480
( ) 1156 * 864
Vrefresh
( ) 60 ( ) 70 ( ) 72 ( ) 75 ( ) 80 ( ) 85 ( ) 100
BitsPerPel
( ) 800 * 600 ( ) 1024 * 768
( ) 1280 * 1024 ( ) 1600 * 1200
( ) 16 colors ( ) 256 colors ( ) High Color(16bits)
( ) True Color(24bits) ( ) True Color(32bits)
Network protocol
( ) Install Unattended
( ) Install Manually
Network protocol property (for auto-installation)
Connection name
Installation method
Available Protocols
Do not use DHCP
Adapter 1
Use of DHCP
(When TCP/IP selected)
IP-Address
Subnet Mask
Default Gateway
IP address (additional)
( ) TCP/IP
( ) DLC
( ) NWIPX ( ) NetBEUI
( ) NetMon ( ) PPTP
( ) Apple Talk
( ) Use DHCP
(only when added)
Subnet mask (additional)
Default gateway
(additional)
DNS domain name
(only when specified)
DNS server address
(only when specified)
Use WINS
WINS server address
NetBIOS Option
(only when added)
(only when added)
( ) Use
DHCP (only when selected to use)
( ) Use NetBIOS setting from the DHCP Server
( ) Use NetBIOS over TCP/IP
( ) Do not use NetBIOS over TCP/IP
Only when NWIPX is selected
Internal network number
0x
Network number
0x
Frame type
Make copies when installing multiple adapters.
(continued)
17
D Design Sheet
Parameters
Setting
(Continuation of Network protocol)
Connection name
Protocol binding to this
adapter
( ) TCP/IP
( ) DLC
Use of DHCP
(When TCP/IP selected)
( ) Use DHCP
( ) NWIPX ( ) NetBEUI
( ) NetMon ( ) PPTP
( ) Apple Talk
Adapter 2
Do not use DHCP
IP Address
Subnet Mask
Default Gateway
IP address (additional)
(only when added)
Subnet mask (additional)
(only when added)
Default gateway(additional)
(only when added)
DNS domain name
(only when specified)
DNS server address
(only when specified)
Use WINS
WINS server address
( ) Use
DHCP (only when selected to use)
NetBIOS Option
( ) Use NetBIOS setting from the DHCP Server
( ) Use NetBIOS over TCP/IP
( ) Do not use NetBIOS over TCP/IP
Only when NWIPX is selected
Internal network number
Network number
Frame type
0x
0x
(continued)
18
D.2 OS Install Wizard (Windows 2003)
Parameters
Setting
Software Components
Select installation method
( ) Install default Components
( ) Install customized Components
R2
( ) R2 Components
Only when selecting R2 components to install
Active Directory
(
(
(
(
(
)
)
)
)
)
Distributed File System
( ) DFS Management
( ) DFS Replication Service
File Server
( ) Management Console
Microsoft Services for NFS
(
(
(
(
(
(
(
Unix Identity Management
( ) Administration Components
( ) Password Synchronisation
( ) Server For NIS
Windows SharePoint Services
Enable Windows Sharepoint Services
Additional Components
(
(
(
(
(
(
(
(
)
)
)
)
)
)
)
)
Common Log File System
Microsoft .NET Framework2.0(English)
Microsoft .NET Framework2.0(International)
Microsoft .NET Framework2.0 Languagepack
Print Management Console
Storage Manager SAN
Storage Ressource Manager
Windows Subsystem for UNIX based Applications
Uninstall Componennts
(
(
(
(
)
)
)
)
uninstall
uninstall
uninstall
uninstall
)
)
)
)
)
)
)
Application Mode(ADAM)
Claims-Aware Applications
Traditional Applications
Federation Service
Federation Service Proxy
User Name Mapping
Microsoft Services for NFS Administration
Client for NFS
Server for NFS
RPC Portmapper
RPC External Data Representation
Server For NFS Authentication
hidden CFSCommonUIFX
hidden DFSExt
hidden DFSRHelper
set of files from FileServerManagement Console
(continued)
19
D Design Sheet
Parameters
Setting
(Continuation of Software Components)
Only when selecting component to install
Application and utilities
( ) clipboard viewer
( ) Desktop Wallpaper
( ) Document Template
( ) Paint
Accessories
( ) All available mousepointers
( ) Word pad
( ) Calculator
( ) Character Map
Accessibility Wizard
( ) Install
Communications
( ) Chat
( ) Hyper Terminal
Application server
ASP.NET web
development platform
( ) Install
Application server
console
( ) Install
(
(
(
(
(
Internet information
services
(IIS)
(
(
(
(
network COM + access
DTC network access
)
)
)
)
)
FrontPage 2002 Server Extensions
FTP (File Transfer Protocol) service
NNTP Service - NNTP Service
SMTP Service - SMTP Service
World Wide Web Server
- Internet Information Services ASP support
) World Wide Web Server
- Internet Information Services web DAV publishing
) World Wide Web Server
- World Wide Web (WWW) Service
) World Wide Web Server
- Internet Information Services internet data connector
) World Wide Web Server
- Internet Information Services web user interface
( ) Install
( ) Install
Indexing Server Files
( ) Install
Terminal Services
( ) Install
Terminal Services licensing
( ) Install
Remote install Services
( ) Install
Certificate Service
( ) Install ( ) Server components of the Certificate Services
( ) Web client component of the Certificate Services
POP3 root component
( ) Install ( ) POP3 main service
( ) POP3 web user interface
(continued)
20
D.2 OS Install Wizard (Windows 2003)
Parameters
Setting
FTP service property (Only when FTP service is selected)
FTP site directory
(Default - \Inetpub\Ftproot)
WWW service property (Only when WWW service is selected)
WWW server directory
(Default - \Inetsrv\WWWroot)
Terminal server property (Only when terminal server is selected)
Remote Desktop
( ) Permit remote access to this computer
Select the permission of the
application intercivic
( ) advanced security
( ) low level security
License mode
Other network File and Print
Services
( ) Number of connected devices
( ) Number of connected users
Services
( ) Services for Macintosh (SFM)
( ) Print Service for Macintosh
( ) Print Service for UNIX
Networking Services
(
(
(
(
(
)
)
)
)
)
WINS Server
Internet Authentication Service (IAS)
MS DNS Server
Simple TCP/IP Service
MS DHCP Serve
Management and Monitoring
Tools
( ) Network Monitor tools
( ) SNMP Service (Required to install SNMP-ServerView)
SNMP details (Only when SNMP is selected)
Trap
Community name
Trap destination
Security
Send authentication trap
Receivable community
name
Receive SNMP packet
from all hosts
Host name
( ) Send
( ) Receive
(only when specified)
Agent
Contact
Address
Service
( ) Physical
( ) End-to-End
( ) Datalink and sub network
( ) Application
( ) Internet
(continued)
21
D Design Sheet
Parameters
Setting
Active Directory details setting (only when DNS is selected)
Install Active Directory
Active Directory type
( ) Install
(
(
(
(
)
)
)
)
Create a domain in a new forest
Additional domain controller of the existing domain
Create a new child domain under the existing domain tree
Create a new domain tree in the existing fores
Database folder
Log folder
SYSVOL folder location
Compatibility with
( ) Permit
Windows 2000 or earlier
Create a domain in a new forest (only when selected)
Complete DNS name of
the new domain
Domain NetBIOS name
Additional domain controller of the existing domain (only when selected)
User name
Password
Domain
Complete DNS name of
the existing domain
Create a new child domain under the existing domain tree (only when selected)
User name
Password
Domain
Complete DNS name of
the parent domain
New child domain name
Domain NetBIOS name
Create a new domain tree in the existing forest (only when selected)
User name
Password
Domain name
Complete DNS name of
the new domain
Domain NetBIOS name
22
D.3 Application Wizard
D.3 Application Wizard
Parameters
Installable applications
Setting
( ) Fujitsu Server View (Apache version) / RAID
Management Tool
( ) Fujitsu Server View (IIS version) / RAID management
Tool
( ) HRM/server
( ) DSNAP
( ) Windows Server 2003 ServicePack
( ) Windows Server 2003 /R2 recommend Hotfix
( ) Windows Server 2003 x64/R2 X64 recommend Hotfix
Userspecific Command
Userspecific Command
(only when selecting additional software)
( ) Install selected application from Local CD
( ) Install selected application from Remote Server
When installing from remote server ( ) Install
( ) Do not install
Remote Source Path
Remote Username
Remote Password
23
E Accident Sheet
E Accident Sheet
Name (Product ID)
□ PRIMERGY BX620 S4 Server Blade (PG )
OS
Environment
LAN/WAN config.
DATE/TIME
Phase of accident
What did you do?, what message? etc.
Attached paper
Yes / No
For optional configuration and settings, use Configuration Sheet in the section A.
24
PRIMERGY BX620 S4 Server Blade
Configuration Sheets
CA92276-8179-01
Issued on April, 2008
Issued by FUJITSU LIMITED
• The contents of this manual may be revised without prior notice.
• Fujitsu assumes no liability for damages to third party copyrights or other
rights arising from the use of any information in this manual.
• No part of this manual may be reproduced in any form without the prior
written permission of Fujitsu.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising