HD3HDIH/X 1080p Indoor High Resolution True Day/Night IP Dome

HD3HDIH/X 1080p Indoor High Resolution True Day/Night IP Dome
Power Supply
EQUIP ® Series
FCC Compliance Statement
Operating Notes
This dome camera can operate on 24V AC or PoE.
Operating Conditions Avoid:
• Viewing bright objects (for example, light fixtures) for extended
periods
• Operating or storing the unit in the following locations.
• Extremely humid, dusty, hot/cold environments (where the
operating temperature is outside the recommended range of
14°F to 122°F [-10°C to +50°C])
• Close to sources of powerful electromagnetic radiation, such
as radio or TV transmitters
• Close to fluorescent lamps or objects reflecting light
• Under unstable light sources (may cause flickering)
Warnings
Installation and servicing should be performed only by qualified and experienced technicians
to conform to all local codes and to maintain your warranty.
WARNING! 24V AC models require the use of CSA Certified/UL Listed Class 2 power
adapters to ensure compliance with electrical safety standards. Power over
Ethernet (PoE) should meet the IEEE 802.3 af PoE standard.
Information to the User: This equipment has been tested and found to comply with the limits for a
Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
3. 50
3 Camera Adjustment
4 Network Setup
5 Camera Operation
The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-1.
Manufacturer’s Declaration of Conformance
Introduction
The manufacturer declares that the equipment supplied with this guide is compliant with the
essential protection requirements of the EMC directive 2004/108/EC and the General Product Safety
Directive 2001/95/EC, conforming to the requirements of standards EN 55022 for emissions, EN
50130-4 for immunity, and EN 60950 for Electrical Equipment safety.
Thank you for purchasing a Honeywell EQUIP Series 1080p Indoor High Resolution True Day/
Night IP Dome Camera. Before installing the camera, please read this guide carefully and verify
your model:
HD3HDIH/HD3HDIHX, 1080p resolution, 2.9 - 9 mm Motorized Focus and Zoom (MFZ) lens
Before installing the camera, Honeywell recommends that you download the latest software
updates. Go to www.honeywellsystems.com/support/downloadcenter/index.html and follow the
instructions on the page to logon, find your camera, and then download software updates.
1
Preparation
1. Preparing the Camera
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
HVSsupport@honeywell.com
1.
( 46. 8 ”
0 mm
)
4.89”
(124.2 mm)
2 Camera Mounting
North America
1.84”
(46.7 mm)
3.05”
(77.5 mm)
1 Preparation
This Class B digital apparatus complies with Canadian ICES-003.
” (8
9.0 m
m)
(82.
5m
m)
4.9” (125.1 mm)
HD3HDIH(X)
Caution Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Contact Information
 2.88”
(73.10 mm)
Document 800-09854V1 – Rev A – 11/2011
For detailed information for your specific camera, please refer to the appropriate user guide located on
the IP Utility DVD.
Product Dimensions
3.2”
Quick Install Guide
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference. For example, try reorienting or relocating the receiving antenna, increasing the
separation between the equipment and receiver, or connecting the equipment to an outlet on a
different circuit.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of
this product (applicable in the European Union and other European
countries with separate collection systems). This product should be
disposed of, at the end of its useful life, as per applicable local laws,
regulations, and procedures.
4.9” (125.1 mm)
1080p Indoor High Resolution True Day/Night IP Dome Camera
Document 800-09854V1 – Rev A – 11/2011
© 2011 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without
written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However,
Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained
herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such
changes.
a.
Rotate the bubble counterclockwise until it
disconnects.
b.
Remove the turret.
c.
Rotate the camera counterclockwise until it
disconnects from the skirt.
d.
Set aside the bubble, turret, and camera.
Skirt
Camera
Turret
Bubble
2. Preparing the Mounting Surface
(Surface or Flush Mount)
a.
b.
Mark the mounting surface for the screw holes and the wire access hole.
•
Use the mounting template if you are surface mounting your camera.
•
Use the flush mount adapter plate as a template if you are flush mounting
your camera.
Pre-drill holes in the mounting surface as required.
Document 800-09854V1 – Rev A – 11/2011
3. Connecting the Wiring
a.
Pull the wires through the hole until you have at least 4 inches of wire.
b.
Remove the green connector strip from the camera base and make all the necessary
connections.
Alarm
24V AC
Audio
In
In
Out
Out
1
c.
2
3 4
5
6
7
8
PIN
Definition
1
Audio In +
2
Audio In –
3
Audio Out +
4
Audio Out –
5
Alarm In +
6
Alarm In –
7
Alarm Out +
8
Alarm Out –
3
4
Camera Adjustment
1.
2.
Apply power to the camera.
Connect the BNC video cable to the local video out connector and view the
video signal (see illustration below).
Note
If your installation involves a 24V AC power source, then please wait
approximately 60 seconds after connecting to a power source for video to
appear on the local video out.
Loosen the thumbscrew that locks the gimbal assembly in place to adjust the
tilt rotation.
Adjust the camera to the desired view. Adjust the horizontal, pan, and tilt
rotations so that the area of interest is at the center. Final zoom and focus
adjustments can be made using the camera’s web client. See Camera
Operation.
3.
4.
Local video out connector
(for aim and focus)
Top view
Thumbscrew (loosen to
adjust tilt, horizontal, and
Legend
pan rotation)
A = Tilt rotation
B = Horizontal rotation
C = Pan rotation
Connect a twisted pair (UTP) cable from each peripheral alarm contact to each alarm input
on the terminal block. For detailed audio and alarm configuration information, refer to the
appropriate user guide located on your software DVD.
RJ45 Ethernet network connection (using
any type of CAT5 cable). Also for Power
over Ethernet (PoE 802.3af).
Network Setup
Honeywell IP Utility
Note
Before installing and using the Honeywell IP Utility, ensure that your camera is
connected to your network through a CAT5 Ethernet cable.
Note
It is recommended that you disable any Norton’s AntiVirus software that might be
running on the workstation.
To discover the IP camera devices and configure their network settings, you must first install
the IP Utility. See the appropriate user guide located on your software DVD or on the
Honeywell product web site. You must have Windows administrator privileges for the
workstation on which the Honeywell IP Utility is being installed.
1.
Insert the DVD. Autorun will start the installation. If autorun does not start, browse to the
DVD drive and run Honeywell IP Utility Setup.exe.
Follow the steps in the InstallShield Wizard.
Log on to the IP Utility:
a. Double-click the IP Utility icon (
) on the desktop. The logon dialog box
appears.
2.
3.
b.
From the User Name list, select Admin or Guest.
c.
Enter the case-sensitive Password and click
(Administrator) or guest (Guest user).
Note
. The default passwords are 1234
This camera supports the PSIA specification for interoperability between network
video products. There is no support for legacy EQUIP and EQUIP2 products.
Configuring the Network
Power, Alarm, Audio
1.
Cover plate
5.
Note
d.
It is not recommended that you supply both 24V AC and PoE at the same time.
Pull the cables through the back or side entries of the camera skirt, then connect to the
camera assembly. You might have to remove the cover plate for flush mount.
2
6.
Retighten the thumbscrew to lock the gimbal
assembly in place.
Disconnect the BNC video cable.
Camera Mounting
Flush Mount (with or without 4S box)(4S box shown)
1.
Secure the skirt to the ceiling
(hardware not supplied) or to the
wall using the supplied hardware.
1.
Note
You must use screws that are
able to support at least three
times the weight of the camera.
Rotate and align the camera
assembly yellow label (
)
Secure the camera assembly to the
skirt by pushing it into the skirt,
then twisting it clockwise until it
clicks securely in place.
Adjust the camera’s field of view
(see Camera Adjustment).
Install the turret by clicking it into
place.
Install the bubble by placing it on
the camera with the tabs to the left
of the slots, then turning it
clockwise until the tabs click
securely into place.
3.
4.
5.
6.
2.
3.
Surface Mount
2.
After you log on to the IP utility, the devices on the network are automatically
discovered and listed in the Discovery pane. After the initial discovery, auto-refresh
continues to discover newly added network devices.
Connect to your IP camera device by double-clicking it in the Discovery pane or by
selecting it and clicking
.
Configure the IP network settings:
•
Automatically. Connect to the device, click the System tab, select to Obtain an
IP Address automatically, enter the Device Name, and click Apply. The network
settings are automatically assigned from the network server.
•
Manually. Connect to the device, click the System tab. Ensure Obtain an IP
Address automatically is not selected, then enter the Device Name, IP Address,
Subnet Mask, and Gateway values. Click Apply.
Skirt
Screws
Note
Camera assembly
2.
3.
Turret
4.
Bubble
5.
6.
Use the screws (not supplied) to
connect the adapter plate directly
to the ceiling or wall. Or, use your
own screws to connect the adapter
plate to the 4S box which is
attached to the ceiling or wall.
You must use screws that are
able to support at least three
times the weight of the camera.
Gently push the screw caps into
place over the screw heads.
Secure the camera assembly to the
adapter plate by twisting clockwise
until it clicks securely in place.
Adjust the camera’s field of view
(see Camera Adjustment).
Install the turret by clicking it into
place.
Install the bubble by placing it on
the camera with the tabs to the left
of the slots, then turning it
clockwise until the tabs click
securely into place.
Caution Check the IP network settings before clicking Apply. Incorrect values might cause
a failure when connecting to the device.
Note
Contact your network administrator if you have any network-related issues or
questions about your network.
4S box (not supplied and optional)
Adapter plate
Screws
Screw caps
Camera assembly
Turret
Bubble
5
Camera Operation
The camera has a web client that enables you to view video and configure device settings
for the camera using a standard web browser. See the appropriate user guide located on
your software DVD to set up your web browser to view video. To log on to the web client
application:
1.
2.
3.
4.
Launch Internet Explorer and enter the URL (IP address) for the network camera.
OR, launch the web client application from the IP Utility by clicking Launch Browser.
Select the User Name as admin or Guest.
Enter the case-sensitive password and click
. The default passwords are 1234
(Administrator) or guest (Guest user).
Select the Zoom and Focus tab. Adjust the field of view by changing the zoom range
and re-focusing.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising