Child Restraints Supplement 2001-2015 Minivan

Child Restraints Supplement 2001-2015 Minivan
2001–2015 MINIVAN CHILD PASSENGER SAFETY
SUPPLEMENT
Chrysler/Dodge
©2015 FCA US LLC. All Rights Reserved. Chrysler and Dodge are registered trademarks of FCA US LLC.
SECTION
TABLE OF CONTENTS
PAGE
1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2
INSTALLING CHILD RESTRAINTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
OPERATING INSTRUCTIONS FOR BUILT-IN (INTEGRATED) CHILD RESTRAINT — IF EQUIPPED . . . 8
4
INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2 INTRODUCTION
INTRODUCTION
CONTENTS
䡵 Welcome From FCA US LLC. . . . . . . . . . . . . . . . . . .3
䡵 How To Use This Supplement. . . . . . . . . . . . . . . . . .3
INTRODUCTION 3
Welcome From FCA US LLC
How To Use This Supplement
If you have opened this guide, chances are you have
questions about the correct use of child restraints in your
vehicle. This supplement has been developed to help answer those questions. This document is intended to supplement the information provided in the Owner’s Manual
and/or User Guide that came with your vehicle. If you no
longer have your Owner’s Manual or User Guide, please
visit www.techauthority.com to order a replacement.
Section two of this supplement, “Installing Child Restraints,” provides general information about the installation of child restraints in vehicles. It provides step-by-step
instructions for installing a car seat using either the seat
belts or the LATCH anchorages in your vehicle. Read this
section to learn how to:
This guide does not cover the proper selection of car seats or
the proper usage of car seats. For questions about car seat
selection and usage, please visit NHTSA’s website: http://
www.safercar.gov/parents/Car-Seat-Safety.htm.
This
website also features videos showing step-by-step installation of different types of car seats.
• Locate LATCH and Tether anchorages in vehicles
• Install a car seat using LATCH
• Install a car seat using seat belts
This section also includes key warnings about the misuse of
car seats. Read and follow all of these warnings when
transporting children in your vehicle.
Section three provides instructions for using the built-in
(integrated) child restraint, if your vehicle is equipped with
one.
Section four provides information that is specific for the
Model Year, Make and Model of your vehicle. To use this
section, first refer to the table of contents to find your
vehicle. Some listings will include a range of model years.
Click on the section for your vehicle to find information
about:
• Locating the LATCH anchorages in your vehicle
• Frequently asked questions about LATCH
• Directions for locating and using the Tether Anchorages
in your vehicle
• Seat belt systems in your vehicle for installing car seats
• Frequently asked questions about seat belts and car seats
Copyright ©2015 FCA US LLC
4 INSTALLING CHILD RESTRAINTS
INSTALLING CHILD RESTRAINTS
CONTENTS
䡵 Installing Child Restraints . . . . . . . . . . . . . . . . . . . .5
䡵 Rear-Facing Car Seats And Air Bags . . . . . . . . . . . . .5
䡵 Lower Anchors And Tethers For CHildren (LATCH)
Restraint System . . . . . . . . . . . . . . . . . . . . . . . . . . .5
䡵 Locating The LATCH And Tether Anchorages . . . . . .5
䡵 Installing Child Restraints Using The LATCH
Lower Anchorages . . . . . . . . . . . . . . . . . . . . . . . . .5
䡵 How To Stow An Unused ALR Seat Belt . . . . . . . . . .6
䡵 Installing Child Restraints Using The Vehicle
Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
䡵 Installing A Child Restraint With A Switchable
Automatic Locking Retractor (ALR) —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
䡵 Installing A Child Restraint With A Cinching Latch
Plate (CINCH) — If Equipped . . . . . . . . . . . . . . . . .6
䡵 Installing Child Restraints Using The Top Tether
Anchorage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
INSTALLING CHILD RESTRAINTS 5
Installing Child Restraints
Locating The LATCH And Tether Anchorages
Children 12 years or younger should ride properly buckled
up in a rear seat, if available. According to crash statistics,
children are safer when properly restrained in the rear seats
rather than in the front.
The lower anchorages are round bars that are found at the
rear of the seat cushion where it meets the seatback. If the bars are not readily visible, they are
located below the anchorage symbols on the seatback (if equipped). You will easily feel them if you
run your finger along the gap between the seatback and seat cushion.
Every state in the United States and all Canadian provinces
require that small children ride in proper restraint systems.
This is the law, and you can be prosecuted for ignoring it.
NOTE: For additional information, refer to www.seatcheck.org
or call 1-866-SEATCHECK. Canadian residents should
refer to Transport Canada’s website for additional information: http://www.tc.gc.ca/eng/motorvehiclesafety/
safedrivers-childsafety-index-53.htm
Rear-Facing Car Seats And Air Bags
WARNING!
• Never place a rear-facing child restraint in front of an
air bag. A deploying passenger Advanced Front Air
Bag can cause death or serious injury to a child 12
years or younger, including a child in a rear-facing
child restraint.
• Only use a rear-facing child restraint in a vehicle with
a rear seat.
Lower Anchors And Tethers For CHildren (LATCH)
Restraint System
There are tether strap anchorages behind the rear
seating positions located on the back of the seat or
near the floor. See the section “LATCH and Tethers in Your Vehicle” for more information about
finding tethers in your vehicle, as not all seating positions
have a tether anchorage and some may be hidden behind a
panel or cover.
Always follow the directions of the child restraint manufacturer when installing your child restraint. Not all child
restraint systems will be installed as described here.
Installing Child Restraints Using The LATCH Lower
Anchorages
1. If the selected seating position has a Switchable Automatic Locking Retractor (ALR) seat belt, stow the seat
belt, following the instructions below. See the section
“Seat Belt Systems in Your Vehicle” to check what type of
seat belt each seating position has.
2. Loosen the adjusters on the lower straps and on the
tether strap of the child seat so that you can more easily
attach the hooks or connectors to the vehicle anchorages.
3. Place the child seat between the lower anchorages for
that seating position. For some second row seats, you
may need to recline the seat and/or raise the head
restraint to get a better fit. If the rear seat can be moved
forward and rearward in the vehicle, you may wish to
move it to its rear-most position to make room for the
child seat. You may also move the front seat forward to
allow more room for the child seat.
Your vehicle is equipped with the child restraint anchorage
system called LATCH, which stands for Lower Anchors and
Tethers for CHildren. The LATCH system has three vehicle
anchor points for installing LATCH-equipped child seats.
There are two lower anchorages located at the back of the
seat cushion where it meets the seatback and one top tether
anchorage located behind the seating position. These anchorages are used to install LATCH-equipped child seats
without using the vehicle’s seat belts. Some seating positions may have a top tether anchorage but no lower anchorages. In these seating positions, the seat belt must be used
with the top tether anchorage to install the child restraint.
NOTE: The LATCH system was phased into vehicles during
the 2000–2002 model years. Certain 2000 and 2001 model
year vehicles did not feature lower anchorages. These
vehicles had tether anchorages only. See the section
“LATCH and Tethers in Your Vehicle” for more information.
4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seating
position.
5. If the child restraint has a tether strap, connect it to the
top tether anchorage. See the section “LATCH and Tethers in Your Vehicle” for directions to attach a tether
anchor.
6. Tighten all of the straps as you push the child restraint
rearward and downward into the seat. Remove slack in
the straps according to the child restraint manufacturer’s
instructions.
7. Test that the child restraint is installed tightly by pulling
back and forth on the child seat at the belt path. It should
not move more than 1 inch (25.4 mm) in any direction.
6 INSTALLING CHILD RESTRAINTS
How To Stow An Unused ALR Seat Belt
When using the LATCH attaching system to install a child
restraint, stow all ALR seat belts that are not being used by
other occupants or being used to secure child restraints. An
unused belt could injure a child if they play with it and
accidentally lock the seat belt retractor. Before installing a
child restraint using the LATCH system, buckle the seat belt
behind the child restraint and out of the child’s reach. If the
buckled seat belt interferes with the child restraint installation, instead of buckling it behind the child restraint, route
the seat belt through the child restraint belt path and then
buckle it. Do not lock the seat belt. Remind all children in
the vehicle that the seat belts are not toys and that they
should not play with them.
WARNING!
• Improper installation of a child restraint to the
LATCH anchorages can lead to failure of the restraint.
The child could be badly injured or killed. Follow the
child restraint manufacturer’s directions exactly when
installing an infant or child restraint.
• Child restraint anchorages are designed to withstand
only those loads imposed by correctly-fitted child
restraints. Under no circumstances are they to be used
for adult seat belts, harnesses, or for attaching other
items or equipment to the vehicle.
Installing Child Restraints Using The Vehicle Seat
Belt
The seat belts in the passenger seating positions are
equipped with either a Switchable Automatic Locking Retractor (ALR) or a cinching latch plate or both. Both types of
seat belts are designed to keep the lap portion of the seat belt
tight around the child restraint so that it is not necessary to
use a locking clip.
The ALR retractor can be “switched” into a locked mode by
pulling all of the webbing out of the retractor and then letting
the webbing retract back into the retractor. If it is locked, the
ALR will make a clicking noise while the webbing is pulled
back into the retractor. For additional information on ALR,
refer to the section “Seat Belt Systems in Your Vehicle.” The
cinching latch plate is designed to hold the lap portion of the
seat belt tight when webbing is pulled tight and straight
through a child restraint’s belt path.
When installing a forward-facing child restraint, always use
the tether anchor up to the maximum weight allowed. See
the section “LATCH and Tethers in Your Vehicle” for more
information about LATCH weight limits.
Installing A Child Restraint With A Switchable
Automatic Locking Retractor (ALR) — If Equipped
1. Place the child seat in the center of the seating position.
For some second row seats, you may need to recline the
seat and/or raise the head restraint to get a better fit. If
the rear seat can be moved forward and rearward in the
vehicle, you may wish to move it to its rear-most position
to make room for the child seat. You may also move the
front seat forward to allow more room for the child seat.
2. Pull enough of the seat belt webbing from the retractor to
pass it through the belt path of the child restraint. Do not
twist the belt webbing in the belt path.
3. Slide the latch plate into the buckle until you hear a “click.”
4. Pull on the webbing to make the lap portion tight against
the child seat.
5. To lock the seat belt, pull down on the shoulder part of
the belt until you have pulled all the seat belt webbing
out of the retractor. Then, allow the webbing to retract
back into the retractor. As the webbing retracts, you will
hear a clicking sound. This means the seat belt is now in
the Automatic Locking mode.
6. Try to pull the webbing out of the retractor. If it is locked,
you should not be able to pull out any webbing. If the
retractor is not locked, repeat step 5.
7. Finally, pull up on any excess webbing to tighten the lap
portion around the child restraint while you push the child
restraint rearward and downward into the vehicle seat.
8. If the child restraint has a top tether strap and the seating
position has a top tether anchorage, connect the tether
strap to the anchorage and tighten the tether strap. See
the section “LATCH and Tethers in Your Vehicle” for
directions to attach a tether anchor.
9. Test that the child restraint is installed tightly by pulling
back and forth on the child seat at the belt path. It should
not move more than 1 inch (25.4 mm) in any direction.
Any seat belt system will loosen with time, so check the belt
occasionally, and pull it tight if necessary.
WARNING!
Do not use the Automatic Locking Mode to restrain
occupants who are wearing the seat belt or children who
are using booster seats. The locked mode is only used to
install rear-facing or forward-facing child restraints that
have a harness for restraining the child.
Installing A Child Restraint With A Cinching Latch
Plate (CINCH) — If Equipped
1. Place the child seat in the center of the seating position.
For some second row seats, you may need to recline the
seat and/or raise the head restraint to get a better fit. If
the rear seat can be moved forward and rearward in the
vehicle, you may wish to move it to its rear-most position
to make room for the child seat. You may also move the
front seat forward to allow more room for the child seat.
2. Next, pull enough of the seat belt webbing from the
retractor to pass it through the belt path of the child
restraint. Do not twist the belt webbing in the belt path.
3. Slide the latch plate into the buckle until you hear a
“click.”
INSTALLING CHILD RESTRAINTS 7
4. Finally, pull up on any excess webbing to tighten the lap
portion around the child restraint while you push the
child restraint rearward and downward into the vehicle
seat.
5. If the child restraint has a top tether strap and the seating
position has a top tether anchorage, connect the tether
strap to the anchorage and tighten the tether strap. See
the section “LATCH and Tethers in Your Vehicle” for
directions to attach a tether anchor.
6. Test that the child restraint is installed tightly by pulling
back and forth on the child seat at the belt path. It should
not move more than 1 inch (25.4 mm) in any direction.
Any seat belt system will loosen with time, so check the belt
occasionally, and pull it tight if necessary.
If the buckle or the cinching latch plate is too close to the belt
path opening of the child restraint, you may have trouble
tightening the seat belt. If this happens, disconnect the latch
plate from the buckle and twist the short buckle-end belt up
to three full turns to shorten it. Insert the latch plate into the
buckle with the release button facing out, away from the
child restraint. Repeat steps 4 to 6, above, to complete the
installation of the child restraint.
If the belt still cannot be tightened after you shorten the
buckle, disconnect the latch plate from the buckle, turn the
buckle around one half turn, and insert the latch plate into
the buckle again. If you still cannot make the child restraint
installation tight, try a different seating position.
Installing Child Restraints Using The Top Tether
Anchorage
WARNING!
• In a collision, an unrestrained child, even a tiny baby,
can become a projectile inside the vehicle. The force
required to hold even an infant on your lap could
become so great that you could not hold the child, no
matter how strong you are. The child and others could
be severely injured or killed. Any child riding in your
vehicle should be in a proper restraint for the child’s
size.
• Never place a rear-facing child restraint in front of an
air bag. A deploying Passenger Advanced Front Air
Bag can cause death or serious injury to a child 12
years or younger, including a child in a rear-facing
child restraint.
• Only use a rear-facing child restraint in a vehicle with
a rear seat.
• Improper installation of a child restraint to the
LATCH anchorages can lead to failure of an infant or
child restraint. The child could be severely injured or
killed. Follow the manufacturer’s directions exactly
when installing an infant or child restraint.
• An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the
child. Use only the anchor positions directly behind
the child seat to secure a child restraint top tether
strap.
• If your vehicle is equipped with a split rear seat, make
sure the tether strap does not slip into the opening
between the seatbacks as you remove slack in the
strap.
WARNING!
See the section “LATCH and Tethers in Your Vehicle” for
specific instructions for using the tether anchorages in your
vehicle.
WARNING!
Do not attach a tether strap for a rear-facing car seat to
any location in front of the car seat, including the seat
frame or a tether anchorage. Only attach the tether strap
of a rear-facing car seat to the tether anchorage that is
approved for that seating position, located behind the
top of the vehicle seat. See the section “LATCH and
Tethers in Your Vehicle” for the location of approved
tether anchorages in your vehicle.
If your vehicle is equipped with in-floor storage, do not
install a rear-facing car seat using a rear support leg in
this vehicle. The floor of this vehicle is not designed to
manage the crash forces of this type of car seat. In a
crash, the support leg may not function as it was
designed by the car seat manufacturer, and your child
may be more severely injured as a result.
8 OPERATING INSTRUCTIONS FOR BUILT-IN (INTEGRATED) CHILD RESTRAINT — IF EQUIPPED
OPERATING INSTRUCTIONS FOR BUILT-IN (INTEGRATED)
CHILD RESTRAINT — IF EQUIPPED
CONTENTS
䡵 Operating Instructions For Built-In (Integrated)
Child Restraint — If Equipped . . . . . . . . . . . . . . . . .9
䡵 Who Should Use This Child Seat: . . . . . . . . . . . . . . .9
䡵 Who Should Use Adult Seat And Belts: . . . . . . . . . . .9
䡵 To Open The Child Restraint: . . . . . . . . . . . . . . . . . .9
䡵 To Secure The Child: . . . . . . . . . . . . . . . . . . . . . . .10
䡵 To Remove The Child: . . . . . . . . . . . . . . . . . . . . . .11
䡵 To Clean The Removable Pad: . . . . . . . . . . . . . . . . .11
䡵 To Recline The Child Seat:. . . . . . . . . . . . . . . . . . . .11
䡵 Rear Bucket Seats Equipped With Child Restraint . . .12
OPERATING INSTRUCTIONS FOR BUILT-IN (INTEGRATED) CHILD RESTRAINT — IF EQUIPPED
Operating Instructions For Built-In (Integrated) Child
Restraint — If Equipped
9
Who Should Use Adult Seat And Belts:
Children over 23 kg (50 pounds) and adults.
Refer to the picture below to become familiar with the parts
of the child seat and five-point seat belts. This child restraint
system conforms to U.S. Federal Motor Vehicle Safety
Standard 213 and Canada Motor Vehicle Safety Standard
No. 213.4.
Children over 23 kg (50 pounds) should find that the adult
seat when used with the adult belts equipped with adjustable upper anchorages provide a safe and comfortable fit
(Figure 3).
Figure 1
A – Removable Pad
B – Buckle
C – Seat Belt Latch Plates
D – Buckle Release Button
E – Release Handle
F – Shoulder Belt Adjustment
Strap
G – Shoulder Belt Clip
Figure 3
To Open The Child Restraint:
Grasp the upper portion (leg rest pad) (Figure 4) and lower
the child seat cushion.
It is important to use an approved rear-facing infant restraint for a full year to allow the neck and spine to develop
enough to support the weight of the child’s head in the
event of a collision.
WARNING!
Failure to follow these instructions can result in your
child striking the vehicle’s interior during a sudden
stop or crash. Snugly adjust the belts provided with the
child restraint around your child.
Who Should Use This Child Seat:
Figure 4
Children 10-23 kg (22-50 pounds).
This integrated child seat is designed for use only by
children who weigh between 10 and 23 kg (22 and 50
pounds) and whose shoulders are not above the shoulder
belt slot position and who are capable of sitting upright
alone (Figure 2).
Figure 2
WARNING!
Do not use this cushion as a booster chair with adult
seat belts. Serious or fatal injury to the child could
result in the event of an accident.
10 OPERATING INSTRUCTIONS FOR BUILT-IN (INTEGRATED) CHILD RESTRAINT — IF EQUIPPED
To Secure The Child:
1. Before placing the child in the seat, add slack to the
shoulder belts. Release the seat belts by pulling up on the
shoulder belt adjustment strap located at the top of the
seat, then pull on the seat belts (Figure 5).
Figure 7
4. Pull the shoulder belt adjustment strap firmly until the
shoulder belts are tight against the child’s shoulders. You
should not be able to put more than two fingers between
the shoulder belts and the child’s chest (Figure 8).
Figure 5
WARNING!
Whenever a child is using the integrated child seat, be
sure that the head restraint is installed in the fully
lowered position or personal injury may result in the
event of an accident.
2. Place the child into the child seat and put a shoulder belt
over each shoulder. Insert both seat belt latch plates into
the buckle and pull up on them to make sure they are
firmly latched (Figure 6).
Figure 8
A ratcheting sound should be heard as the excess belt
material returns to the retractor and belts become secure
around the child.
NOTE: Once properly adjusted there is no need to release
the seat belts until a change in clothing or height or weight
occurs.
WARNING!
Figure 6
NOTE: Be sure that the seat belt buckle is free of foreign
objects that may prevent you from properly latching the
latch plates. If an object is in the opening, and cannot be
removed, see your dealer for service immediately.
3. Fasten the two halves of the shoulder belt clip together
and put it 5-8 cm (2-3 inches) below the child’s chin. The
purpose of the clip is to keep the shoulder belts positioned correctly on the shoulders (Figure 7).
• A frayed or torn child restraint belt could rip apart in
a collision and leave your child with no protection.
Inspect the belt system periodically, checking for cuts,
frays, or loose parts. Damaged parts must be replaced
immediately.
• Do not disassemble or modify the system.
• Child restraint belt systems must be replaced after a
collision if they have been damaged (bent buckle or
5-point connector, torn webbing, etc.). Similarly, the
child restraint-equipped bench or bucket seat must be
replaced after a collision if it is damaged (bent or
broken seat frame, etc.).
OPERATING INSTRUCTIONS FOR BUILT-IN (INTEGRATED) CHILD RESTRAINT — IF EQUIPPED
To Remove The Child:
1. To release the child from the seat belts, separate the
halves of the shoulder belt clip. Then push the red release
button in the buckle. Move the shoulder belts to the side
and remove the child from the seat.
11
To replace the removable pad, align the opening in the pad
with the crotch belt and buckle and press the pad into place
(Figure 11).
2. Return the buckle assembly to its lowered position for
stowage after each use (Figure 9). This will allow the
child seat to be neatly folded when not in use.
Figure 11
CAUTION!
Failure to follow the washing instructions on the removable pad may result in premature wear.
Figure 9
To Recline The Child Seat:
To Clean The Removable Pad:
The cloth pad is attached to the seat frame with a fastener
strip and can be easily removed (Figure 10) and machine
washed according to directions on the pad.
1. Unlatch the recliner by lifting the release handle (Figure
12).
Figure 12
Figure 10
2. Recline the seat by pushing rearward on the seat back
(Figure 13).
Figure 13
12 OPERATING INSTRUCTIONS FOR BUILT-IN (INTEGRATED) CHILD RESTRAINT — IF EQUIPPED
NOTE: The seat is equipped with an interlock mechanism
to prevent the seat back from being folded while the child
seat is open (Figure 14). Returning the child seat(s) to their
stowed position(s) will allow the seat back to be folded.
Rear Bucket Seats Equipped With Child Restraint
WARNING!
The rear bucket seats can be tilted forward for easy
access to the third seat or rear cargo area. Do not tilt the
seat forward when a child is using the child restraint
equipped seat or personal injury may result.
Figure 14
Figure 15
INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
13
INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
CONTENTS
䡵 2001 MODEL YEAR: CHRYSLER TOWN &
COUNTRY/CHRYSLER VOYAGER/DODGE
CARAVAN/DODGE GRAND CARAVAN . . . . . . . .14
▫ LATCH And Tethers In Your Vehicle . . . . . . . . . .14
▫ Center Seat LATCH . . . . . . . . . . . . . . . . . . . . . .15
▫ Connecting The Top Tether Strap (With Either
Lower Anchors Or Vehicle Seat Belt) . . . . . . . . . .15
▫ Seat Belt Systems In Your Vehicle . . . . . . . . . . . . .16
䡵 2002–2004 MODEL YEARS: CHRYSLER TOWN &
COUNTRY/CHRYSLER VOYAGER/DODGE
CARAVAN/DODGE GRAND CARAVAN . . . . . . . .17
▫ LATCH And Tethers In Your Vehicle . . . . . . . . . .17
▫ Connecting The Top Tether Strap (With Either
Lower Anchors Or Vehicle Seat Belt) . . . . . . . . . .18
▫ Seat Belt Systems In Your Vehicle . . . . . . . . . . . . .19
䡵 2005–2007 MODEL YEARS: CHRYSLER TOWN &
COUNTRY/DODGE CARAVAN/
DODGE GRAND CARAVAN . . . . . . . . . . . . . . . . .20
▫ LATCH And Tethers In Your Vehicle . . . . . . . . . .20
▫ Center Seat LATCH — With Stow ’n Go . . . . . . . .22
▫ Connecting The Top Tether Strap (With Either
Lower Anchors Or Vehicle Seat Belt) . . . . . . . . . .22
▫ Seat Belt Systems In Your Vehicle . . . . . . . . . . . . .23
䡵 2008–2015 MODEL YEARS: CHRYSLER TOWN &
COUNTRY/DODGE GRAND CARAVAN . . . . . . . .24
▫ LATCH And Tethers In Your Vehicle . . . . . . . . . .24
▫ Center Seat LATCH . . . . . . . . . . . . . . . . . . . . . .26
▫ Connecting The Top Tether Strap (With Either
Lower Anchors Or Vehicle Seat Belt) . . . . . . . . . .26
▫ Seat Belt Systems In Your Vehicle . . . . . . . . . . . . .27
▫ Integrated Child Booster Seat — If Equipped . . . .28
14 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
2001 MODEL YEAR: CHRYSLER TOWN & COUNTRY/CHRYSLER VOYAGER/DODGE CARAVAN/
DODGE GRAND CARAVAN
LATCH And Tethers In Your Vehicle
LATCH Positions For Installing Child Restraints In This
Vehicle
2nd Row Quad Seat LATCH Lower Anchorages
2nd Row Bench Seat
3rd Row Bench Seat LATCH Lower Anchorages
Locating The Tether Anchorages In This Vehicle
2nd Row Quad Seating
•
•
Lower Anchorage Symbol (2 Anchorages Per
Seating Position)
Top Tether Anchorage Symbol
Locating The LATCH Lower Anchorages In This
Vehicle
2nd Row Bench Seat Tether Strap Anchorages
2nd Row Bench Seat LATCH Lower Anchorages
INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
3rd Row Bench Seat Tether Strap Anchorages
2nd Row Quad Tether Strap Anchorage
Frequently Asked Questions
What is the weight limit (child’s weight + weight of
65
the child restraint) for using the LATCH anchorage
pounds
system to attach the child restraint?
Can the LATCH anchorages and the seat belt be
used together to attach a rear-facing or forwardfacing child restraint?
Can two child restraints be attached using a common
lower LATCH anchorage?
No
No
Can the rear-facing child restraint touch the back of
the front passenger seat?
Yes
Can the head restraints be removed?
Yes
Center Seat LATCH
To install a child restraint in the center position using the
LATCH anchorages, attach the lower hooks or connectors
on the child restraint to the two inner bars in the row. If
LATCH is used for the center seating position, do not use
the lower anchorages in the outboard positions.
If a child restraint installed in the center position blocks the
seat belt webbing or buckle for the outboard position, do not
use that outboard position. If a child seat in the center
position blocks the outboard LATCH anchors or seat belt, do
not install a child seat in that outboard position.
WARNING!
Never use the same lower anchorage to attach more than
one child restraint. Please refer to “Installing The
LATCH-Compatible Child Restraint System” for typical
installation instructions.
15
About LATCH
Use the LATCH anchorage system until the combined weight of the child and the child restraint is
65 lbs (29.5 kg). Use the seat belt and tether anchor
instead of the LATCH system once the combined
weight is more than 65 lbs (29.5 kg).
Do not use the seat belt when you use the LATCH
anchorage system to attach a rear-facing or forwardfacing child restraint.
Never “share” a LATCH anchorage with two or
more child restraints. If the center position does not
have dedicated LATCH lower anchorages, use the
seat belt to install a child seat in the center position
next to a child seat using the LATCH anchorages in
an outboard position.
The child seat may touch the back of the front passenger seat if the child restraint manufacturer also
allows contact. See your child restraint Owner’s
Manual for more information.
All adjustable head restraints may be removed.
Connecting The Top Tether Strap (With Either Lower
Anchors Or Vehicle Seat Belt)
When installing a forward-facing child restraint, always
secure the top tether strap, up to the tether anchor weight
limit, whether the child restraint is installed with the lower
anchors or the vehicle seat belt.
1. Look behind the seating position where you plan to
install the child restraint to find the tether anchorage. You
may need to move the seat forward to provide better
access to the tether anchorage. If there is no top tether
anchorage for that seating position, move the child
restraint to another position in the vehicle if one is
available.
2. Route the tether strap to provide the most direct path for
the strap between the anchor and the child seat. If your
vehicle is equipped with adjustable rear head restraints,
raise the head restraint, and where possible, route the
tether strap under the head restraint and between the two
posts. If not possible, lower the head restraint and pass
the tether strap around the outboard side of the head
restraint.
16 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
3. Attach the tether strap hook of the child restraint to the
top tether anchorage.
4. Remove slack in the tether strap according to the child
restraint manufacturer’s instructions.
WARNING!
• An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the
child. Use only the anchorage position directly behind
the child seat to secure a child restraint top tether
strap.
• If your vehicle is equipped with a split rear seat, make
sure the tether strap does not slip into the opening
between the seatbacks as you remove slack in the
strap.
2nd Row Quad Seating – All Positions CINCH,
3rd Center CINCH Lap Belt
Seat Belt Systems In Your Vehicle
Lap/Shoulder Belt Systems For Installing Child Restraints
In This Vehicle
2nd Row Bench Seat – All Positions CINCH,
3rd Center CINCH Lap Belt
Frequently Asked Questions About Seat Belts And Car Seats
What is the weight limit (child’s weight + weight
Weight limit
Always use the tether anchor when using the seat
of the child restraint) for using the Tether Anchor
of the Child
belt to install a forward facing child restraint, up
with the seat belt to attach a forward facing child
Restraint
to the recommended weight limit of the child rerestraint?
straint.
Can the rear-facing child restraint touch the back
Yes
The child seat may touch the back of the front
of the front passenger seat?
passenger seat if the child restraint manufacturer
also allows contact. See your child restraint Owner’s Manual for more information.
Can the head restraints be removed?
Yes
All adjustable head restraints may be removed.
Yes
In positions with cinching latch plates (CINCH),
Can the buckle stalk be twisted to tighten the seat
belt against the seat belt path of the child rethe buckle stalk may be twisted up to 3 full turns.
straint?
INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
2002–2004 MODEL YEARS: CHRYSLER TOWN & COUNTRY/CHRYSLER VOYAGER/DODGE CARAVAN/
DODGE GRAND CARAVAN
LATCH And Tethers In Your Vehicle
LATCH Positions For Installing Child Restraints In This
Vehicle
2nd Row Quad Seat LATCH Lower Anchorages
2nd Row Bench Seat
3rd Row Bench Seat Has No LATCH Lower Anchorages
Locating The Tether Anchorages In This Vehicle
2nd Row Quad Seating
•
•
Lower Anchorage Symbol (2 Anchorages Per
Seating Position)
Top Tether Anchorage Symbol
Locating the LATCH Lower Anchorages In This
Vehicle
2nd Row Bench Seat Tether Strap Anchorages
2nd Row Bench Seat LATCH Lower Anchorages
17
18 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
3rd Row Bench Seat Tether Strap Anchorage
2nd Row Quad Seat Tether Strap Anchorage
Frequently Asked Questions
What is the weight limit (child’s weight + weight of
65
the child restraint) for using the LATCH anchorage
pounds
system to attach the child restraint?
Can the LATCH anchorages and the seat belt be
used together to attach a rear-facing or forwardfacing child restraint?
Can two child restraints be attached using a common
lower LATCH anchorage?
No
No
Can the rear-facing child restraint touch the back of
the front passenger seat?
Yes
Can the head restraints be removed?
Yes
WARNING!
Never use the same lower anchorage to attach more than
one child restraint. Please refer to “Installing The
LATCH-Compatible Child Restraint System” for typical
installation instructions.
Connecting The Top Tether Strap (With Either Lower
Anchors Or Vehicle Seat Belt)
When installing a forward-facing child restraint, always
secure the top tether strap, up to the tether anchor weight
limit, whether the child restraint is installed with the lower
anchors or the vehicle seat belt.
1. Look behind the seating position where you plan to
install the child restraint to find the tether anchorage. You
may need to move the seat forward to provide better
access to the tether anchorage. If there is no top tether
anchorage for that seating position, move the child
restraint to another position in the vehicle if one is
available.
About LATCH
Use the LATCH anchorage system until the combined weight of the child and the child restraint is
65 lbs (29.5 kg). Use the seat belt and tether anchor
instead of the LATCH system once the combined
weight is more than 65 lbs (29.5 kg).
Do not use the seat belt when you use the LATCH
anchorage system to attach a rear-facing or forwardfacing child restraint.
Never “share” a LATCH anchorage with two or
more child restraints. If the center position does not
have dedicated LATCH lower anchorages, use the
seat belt to install a child seat in the center position
next to a child seat using the LATCH anchorages in
an outboard position.
The child seat may touch the back of the front passenger seat if the child restraint manufacturer also
allows contact. See your child restraint Owner’s
Manual for more information.
All adjustable head restraints may be removed.
2. Route the tether strap to provide the most direct path for
the strap between the anchor and the child seat. If your
vehicle is equipped with adjustable rear head restraints,
raise the head restraint, and where possible, route the
tether strap under the head restraint and between the two
posts. If not possible, lower the head restraint and pass
the tether strap around the outboard side of the head
restraint.
3. Attach the tether strap hook of the child restraint to the
top tether anchorage.
4. Remove slack in the tether strap according to the child
restraint manufacturer’s instructions.
INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
19
WARNING!
• An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the
child. Use only the anchorage position directly behind
the child seat to secure a child restraint top tether
strap.
• If your vehicle is equipped with a split rear seat, make
sure the tether strap does not slip into the opening
between the seatbacks as you remove slack in the
strap.
Seat Belt Systems In Your Vehicle
Lap/Shoulder Belt Systems For Installing Child Restraints
In This Vehicle
2nd Row Quad Seating – All Positions CINCH, 3rd
Center CINCH Lap Belt
2nd Row Bench Seat – All Positions CINCH, 3rd Center
CINCH Lap Belt
Frequently Asked Questions About Seat Belts And Car Seats
What is the weight limit (child’s weight + weight
Weight limit
Always use the tether anchor when using the seat
of the child restraint) for using the Tether Anchor
of the Child
belt to install a forward facing child restraint, up
with the seat belt to attach a forward facing child
Restraint
to the recommended weight limit of the child rerestraint?
straint.
Can the rear-facing child restraint touch the back
Yes
The child seat may touch the back of the front
of the front passenger seat?
passenger seat if the child restraint manufacturer
also allows contact. See your child restraint Owner’s Manual for more information.
Can the head restraints be removed?
Yes
All adjustable head restraints may be removed.
Can the buckle stalk be twisted to tighten the seat
Yes
In positions with cinching latch plates (CINCH),
belt against the seat belt path of the child rethe buckle stalk may be twisted up to 3 full turns.
straint?
20 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
2005–2007 MODEL YEARS: CHRYSLER TOWN & COUNTRY/DODGE CARAVAN/DODGE GRAND CARAVAN
LATCH And Tethers In Your Vehicle
LATCH Positions For Installing Child Restraints In This
Vehicle
2nd Row Quad Seating – Stow ‘n Go
•
2nd Row Bench Seat – Non-Stow ‘n Go
•
Lower Anchorage Symbol (2 Anchorages Per
Seating Position)
Top Tether Anchorage Symbol
Locating The LATCH Lower Anchorages In This
Vehicle
2nd Row Quad Seating – Non-Stow ‘n Go
2nd Row Bench Seat LATCH Lower Anchorages
2nd Row Bench Seat – Stow ‘n Go
2nd Row Quad Seat LATCH Lower Anchorages
INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
21
2nd Row Quad Seat Tether Strap Anchorage
3rd Row Bench Seat Has No LATCH Lower Anchorages –
Non-Stow ‘n Go
3rd Row Bench Seat Tether Strap Anchorage
3rd Row Bench Seat LATCH Lower Anchorage – Stow ‘n
Go
Locating The Tether Anchorages In This Vehicle
3rd Row 60/40 Seat Tether Strap Anchorage
2nd Row Bench Seat Tether Strap Anchorages
Frequently Asked Questions
What is the weight limit (child’s weight + weight of
65
the child restraint) for using the LATCH anchorage
pounds
system to attach the child restraint?
Can the LATCH anchorages and the seat belt be
used together to attach a rear-facing or forwardfacing child restraint?
No
About LATCH
Use the LATCH anchorage system until the combined weight of the child and the child restraint is
65 lbs (29.5 kg). Use the seat belt and tether anchor
instead of the LATCH system once the combined
weight is more than 65 lbs (29.5 kg).
Do not use the seat belt when you use the LATCH
anchorage system to attach a rear-facing or forwardfacing child restraint.
22 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
Frequently Asked Questions About LATCH
Can two child restraints be attached using a common
No
Never “share” a LATCH anchorage with two or
lower LATCH anchorage?
more child restraints. If the center position does not
have dedicated LATCH lower anchorages, use the
seat belt to install a child seat in the center position
next to a child seat using the LATCH anchorages in
an outboard position.
Can the rear-facing child restraint touch the back of
No
Contact between the front passenger seat and a child
the front passenger seat?
restraint can affect the passenger air bag suppression
system. See the vehicle Owner’s Manual for more
information about the occupant classification system
in your vehicle.
Can the head restraints be removed? (Non-Stow ‘n
Yes
Non-Stow ‘n Go Seats: All adjustable head restraints
Go Equipped Vehicles)
may be removed.
Can the head restraints be removed? (Stow ‘n Go
No
Stow ‘n Go Seats: Head restraints are not removable.
Equipped Vehicles)
Center Seat LATCH — With Stow ’n Go
If a child restraint installed in the center position blocks the
seat belt webbing or buckle for the outboard position, do not
use that outboard position. If a child seat in the center
position blocks the outboard LATCH anchors or seat belt, do
not install a child seat in that outboard position.
WARNING!
Never use the same lower anchorage to attach more than
one child restraint. Please refer to “Installing The
LATCH-Compatible Child Restraint System” for typical
installation instructions.
Connecting The Top Tether Strap (With Either Lower
Anchors Or Vehicle Seat Belt)
When installing a forward-facing child restraint, always
secure the top tether strap, up to the tether anchor weight
limit, whether the child restraint is installed with the lower
anchors or the vehicle seat belt.
1. Look behind the seating position where you plan to
install the child restraint to find the tether anchorage. You
may need to move the seat forward to provide better
access to the tether anchorage. If there is no top tether
anchorage for that seating position, move the child
restraint to another position in the vehicle if one is
available.
2. Route the tether strap to provide the most direct path for
the strap between the anchor and the child seat. If your
vehicle is equipped with adjustable rear head restraints,
raise the head restraint, and where possible, route the
tether strap under the head restraint and between the two
posts. If not possible, lower the head restraint and pass
the tether strap around the outboard side of the head
restraint.
3. Attach the tether strap hook of the child restraint to the
top tether anchorage.
4. Remove slack in the tether strap according to the child
restraint manufacturer’s instructions.
WARNING!
• An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the child.
Use only the anchorage position directly behind the
child seat to secure a child restraint top tether strap.
• If your vehicle is equipped with a split rear seat, make
sure the tether strap does not slip into the opening
between the seatbacks as you remove slack in the strap.
INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
23
Seat Belt Systems In Your Vehicle
Lap/Shoulder Belt Systems For Installing Child Restraints
In This Vehicle
2nd Row Quad Seating – All Positions CINCH, 3rd
Center CINCH Lap Belt
2nd Row Bench Seat – All Positions CINCH, 3rd Center
CINCH Lap Belt
Frequently Asked Questions About Seat Belts And Car Seats
What is the weight limit (child’s weight + weight
Weight limit
Always use the tether anchor when using the seat
of the child restraint) for using the Tether Anchor
of the Child
belt to install a forward facing child restraint, up
with the seat belt to attach a forward facing child
Restraint
to the recommended weight limit of the child rerestraint?
straint.
Can the rear-facing child restraint touch the back
No
Contact between the front passenger seat and a
of the front passenger seat?
child restraint can affect the passenger air bag
suppression system. See the vehicle Owner’s
Manual for more information about the occupant
classification system in your vehicle.
Can the head restraints be removed? (Non-Stow ‘n
Yes
Non-Stow ‘n Go Seats: All adjustable head reGo Equipped Vehicles)
straints may be removed.
Can the head restraints be removed? (Stow ‘n Go
No
Stow ‘n Go Seats: Head restraints are not removEquipped Vehicles)
able.
Can the buckle stalk be twisted to tighten the seat
Yes
In positions with cinching latch plates (CINCH),
belt against the seat belt path of the child rethe buckle stalk may be twisted up to 3 full turns.
straint?
24 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
2008–2015 MODEL YEARS: CHRYSLER TOWN & COUNTRY/DODGE GRAND CARAVAN
LATCH And Tethers In Your Vehicle
LATCH Positions For Installing Child Restraints In This
Vehicle
Locating The LATCH Lower Anchorages In This
Vehicle
2nd Row Bench Seat LATCH Lower Anchorages
2nd Row Bench Seat – Non-Stow ‘n Go
2nd Row Swivel ‘n Go Seating
2nd Row Quad Seat LATCH Lower Anchorages
2nd Row Quad Seating – Same For Stow ‘n Go And Non
Stow ‘n Go
3rd Row 60/40 Seat LATCH Lower Anchorages
•
•
Lower Anchorage Symbol (2 Anchorages Per
Seating Position)
Top Tether Anchorage Symbol
INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
25
Locating The Tether Anchorages In This Vehicle
3rd Row 60/40 Tether Strap Anchorages
2nd Row Bench Seat Tether Strap Anchorages
2nd Row Quad Seat Tether Strap Anchorages
Frequently Asked Questions
What is the weight limit (child’s weight + weight of
65
the child restraint) for using the LATCH anchorage
pounds
system to attach the child restraint?
Can the LATCH anchorages and the seat belt be
used together to attach a rear-facing or forwardfacing child restraint?
Can two child restraints be attached using a common
lower LATCH anchorage?
No
No
Can the rear-facing child restraint touch the back of
the front passenger seat?
Yes
Can the head restraints be removed? (Non-Stow ‘n
Go Equipped Vehicles)
Can the head restraints be removed? (Stow ‘n Go
Equipped Vehicles)
Yes
Yes
About LATCH
Use the LATCH anchorage system until the combined weight of the child and the child restraint is
65 lbs (29.5 kg). Use the seat belt and tether anchor
instead of the LATCH system once the combined
weight is more than 65 lbs (29.5 kg).
Do not use the seat belt when you use the LATCH
anchorage system to attach a rear-facing or forwardfacing child restraint.
Never “share” a LATCH anchorage with two or
more child restraints. If the center position does not
have dedicated LATCH lower anchorages, use the
seat belt to install a child seat in the center position
next to a child seat using the LATCH anchorages in
an outboard position.
The child seat may touch the back of the front passenger seat if the child restraint manufacturer also
allows contact. See your child restraint Owner’s
Manual for more information.
Second row and the third row center head restraints
are removable.
Only the third row center head restraint is removable.
26 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
NOTE: 2011-2015 Model Years: If the folding, nonadjustable head restraint interferes with the installation of
the child restraint, the head restraint may be folded and the
child seat installed in front of it.
WARNING!
Always make sure the head restraint is in its upright
position when the seat is to be used by an occupant who
is not in a child restraint. Sitting in a seat with the head
restraint in its lowered position could result in serious
injury or death in a collision.
Connecting The Top Tether Strap (With Either Lower
Anchors Or Vehicle Seat Belt)
When installing a forward-facing child restraint, always
secure the top tether strap, up to the tether anchor weight
limit, whether the child restraint is installed with the lower
anchors or the vehicle seat belt.
1. Look behind the seating position where you plan to
install the child restraint to find the tether anchorage. You
may need to move the seat forward to provide better
access to the tether anchorage. If there is no top tether
anchorage for that seating position, move the child
restraint to another position in the vehicle if one is
available.
2. Route the tether strap to provide the most direct path for
the strap between the anchor and the child seat. If your
vehicle is equipped with adjustable rear head restraints,
raise the head restraint, and where possible, route the
tether strap under the head restraint and between the two
posts. If not possible, lower the head restraint and pass
the tether strap around the outboard side of the head
restraint.
3. Attach the tether strap hook of the child restraint to the
top tether anchorage.
Car Seat With Head Restraint Folded
1 – Folded Headrest
2 – Child Restraint
4. Remove slack in the tether strap according to the child
restraint manufacturer’s instructions.
WARNING!
Center Seat LATCH
If a child restraint installed in the center position blocks the
seat belt webbing or buckle for the outboard position, do not
use that outboard position. If a child seat in the center
position blocks the outboard LATCH anchors or seat belt, do
not install a child seat in that outboard position.
WARNING!
Never use the same lower anchorage to attach more than
one child restraint. Please refer to “Installing The
LATCH-Compatible Child Restraint System” for typical
installation instructions.
• An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the
child. Use only the anchorage position directly behind
the child seat to secure a child restraint top tether
strap.
• If your vehicle is equipped with a split rear seat, make
sure the tether strap does not slip into the opening
between the seatbacks as you remove slack in the
strap.
INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
27
Seat Belt Systems In Your Vehicle
Lap/Shoulder Belt Systems For Installing Child Restraints
In This Vehicle
2nd Row Quad Seating – All ALR Except 3rd Center
CINCH
2nd Row Bench Seat – All ALR Except 3rd Center CINCH
2nd Row Swivel ‘n Go Seating
Frequently Asked Questions About Seat Belts And Car Seats
What is the weight limit (child’s weight + weight
Weight limit
Always use the tether anchor when using the seat
of the child restraint) for using the Tether Anchor
of the Child
belt to install a forward facing child restraint, up
with the seat belt to attach a forward facing child
Restraint
to the recommended weight limit of the child rerestraint?
straint.
Can the rear-facing child restraint touch the back
Yes
The child seat may touch the back of the front
of the front passenger seat?
passenger seat if the child restraint manufacturer
also allows contact. See your child restraint Owner’s Manual for more information.
Can the head restraints be removed? (Non-Stow ‘n
Yes
Non-Stow ‘n Go Seats: Second row and third row
Go Equipped Vehicles)
center head restraints are removable.
Can the head restraints be removed? (Stow ‘n Go
Yes
Second Row Bench, Quad Seats and the third row
Equipped Vehicles)
center head restraints are removable.
Can the buckle stalk be twisted to tighten the seat
Yes
In positions with cinching latch plates (CINCH),
belt against the seat belt path of the child rethe buckle stalk may be twisted up to 3 full turns.
straint?
Do not twist the buckle stalk in a seating position
with an ALR retractor.
28 INSTALLING CHILD RESTRAINTS IN YOUR VEHICLE
Integrated Child Booster Seat — If Equipped
The Integrated Child Booster Seat (if equipped) is located in
each second-row passenger seat. The booster seat is designed for children weighing between 48 and 85 lbs (22 and
39 kg) and between 47 in (119 cm) and 57 in (145 cm) tall.
The booster seat is designed to raise the child high enough
to use the vehicle lap and shoulder belt. The booster seat
latch release handle is located at the front of the seat
cushion.
2. Place the child upright in the seat with their back firmly
against the seatback.
3. Grasp the latch plate and pull out the seat belt.
4. Slide the latch plate up the webbing as far as necessary to
allow the seat belt to go around the child’s lap.
NOTE: The lap portion of the seat belt should be low on the
hips and as snug as possible.
5. Once the seat belt is long enough to fit properly, insert the
latch plate into the buckle until you hear a “click.”
6. To remove the slack from the lap belt, pull upward on the
shoulder portion of the seat belt.
Booster Seat Release Handle
1. Pull the release handle forward to release the latch and
seat cushion. Then, lift seat cushion up and push back to
lock it in the booster seat position.
Integrated Child Booster Seat
7. To release the seat belt, push the red button on the buckle.
Booster Seat Position
WARNING!
Failure to comply with the following conditions could
result in serious injury or death:
• The swivel seat should be locked in the forward
facing position when using the booster seat with the
vehicle in motion.
• Be certain that the seat cushion is locked securely into
position before using the seat. Otherwise, the seat will
not provide the proper stability for child seats and/or
passengers. An improperly latched seat cushion could
cause serious injury or death.
INDEX 29
INDEX
Automatic Locking Retractor (ALR) . . . . . . . . . . . . . . . .6
Center Seat LATCH. . . . . . . . . . . . . . . . . . . .6, 15, 22, 26
Child Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Connecting The Top Tether Strap . . . . . . . . .15, 18, 22, 26
Frequently Asked Questions About LATCH . .14, 17, 20, 24
Frequently Asked Questions About Seat Belts
And Car Seats . . . . . . . . . . . . . . . . . . . . .16, 19, 23, 27
How To Stow An Unused ALR Seat Belt. . . . . . . . . . . . .6
Installing A Child Restraint With A Cinching
atch Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installing A Child Restraint With ALR . . . . . . . . . . . . . .6
Installing Child Restraints In Your Vehicle . . . . . . . . .1, 14
Installing Child Restraints Using The LATCH
Lower Anchorages . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installing Child Restraints Using The Top Tether
Anchorage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installing Child Restraints Using The Vehicle
Seat Belt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Integrated Child Booster Seat. . . . . . . . . . . . . . . . . . . .28
Integrated Child Seat . . . . . . . . . . . . . . . . . . . . . . . .1, 9
LATCH And Tethers In Your Vehicle . . . . . . .14, 17, 20, 24
LATCH Lower Anchorages. . . . . . . . . . . . . .14, 17, 20, 24
Locating The LATCH And Tether Anchorages. . . . . . . . .5
Lower Anchors And Tether For CHildren (LATCH) . . . . .5
Operating Instructions For Built-In (Integrated)
Child Restraint). . . . . . . . . . . . . . . . . . . . . . . . . . .1, 9
Rear Facing Car Seats And Air Bags. . . . . . . . . . . . . . . .5
Seat Belt Systems In Your Vehicle . . . . . . . . .16, 19, 23, 27
Top Tether Anchorages . . . . .7, 14, 15, 17, 18, 20, 22, 24, 26
VAN-226-AA
FCA US LLC
© 2015 FCA US LLC, All Rights Reserved
Chrysler and Dodge are registered trademarks of FCA US LLC.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising