LUXOMAT® CdS-DALI/DSI

LUXOMAT® CdS-DALI/DSI
EN
LUXOMAT ® CdS-DALI/DSI
Installation and Operating Instruction for B.E.G. - Photocells CdS-DALI/DSI-SM/-FC
1a. Features
1b. Mounting preparations
•
For connection of up to 50 lamps
•
Suitable for dimmable electronic
ballasts and control modules
•
DALI/DSI output
•
Manual dimming by remote
control
•
Constant light control
•
Manual dimming
•
Luminance (brightness) set point
adjustable
•
Sensor and power sections in
one housing
•
Infrared remote control
•
Dynamic delay
2c. Self test cycle
2a. Mounting LUXOMAT® CdS-DALI/DSI-SM
The detector must be in­stalled
on a solid and level surface.
The circular cover ring must be
removed prior to assembly. To do
this, twist the coverring (D) anticlockwise through approximately
5° and lift off.
Work on the 230 V mains supply
may only be carried out by qualified professionals or by instructed
persons under the direction and
supervision of qualified skilled electrical personnel in accordance with
electrotechnical regulations.
2b. Mounting LUXOMAT®
CdS-DALI/DSI-FC
C
close
68 mm
open
Disconnect supply before installing!
A circular opening of diameter 68 mm
must be produced in the ceiling. Having
connected up the cables in accor­dance
with regulations, the detector is inserted
into the opening as shown in the drawing
opposite and fixed into position with the
assistance of the spring clips.
Having connected up the wires
in accordance with regulations, secure the detector with 2
screws. After installation replace
the lens and lock (turn clockwise). Mains to be connected.
2e. Position DIP-Switches, LEDs and Potentiometer FC
2d. Position DIP-Switches, LEDs and Potentiometer SM
I
ON
C
B
A
The product enters an initial 60-second
self-test cycle, when the supply is first
connected. The occupancy detector is
ready for operation.
OFF
A B C
DIP
1 2 3
II III
I II III
1
2
DIP
CdS-DALI/DSISurface mounting
ON
OFF
CdS-DALI/DSIFalse ceiling mounting
DIP 1 100 % ON/OFF
Potentiometer A Lux
LED Igreen
DIP 2 LED ON/OFF
Potentiometer B Follow-up time
LED II red
DIP 3 DALI/DSI = Change between DALI/DSI mode
Potentiometer C Stoving time
LED IIIwhite
3. Putting into operation / Settings
25
30 60 22
120
5018
A
4016
R1
3010
15
TEST 5110
36
16 10
5
2
1
TEST 15 30
R2
2000
1200
600
200
40
Symbol
100 h
75 h
25 h
50 h
120 60 50
A
40
30
15
5 10
The ON delay time is determined automatically. The sooner the
brightness decreases, the shorter the time.
Twilight-switch for light control
The switch-on value for the light can be set at between 10 and 2000 Lux.
Using the rotary control, the luminance set points can be set as desired.
Symbol : Night-time operation
16 10
5
2
1
TEST 15 30
1
30 25 22
18
16
R1
10
TEST 1 3 6
2
2000
1200
600
200
40
: 300 Lux
Stoving time 25 - 100 h
The stoving time can be set at between 25 and 100 h in 4 steps.
Activation with remote control
The DIP switch settings are overriden
using the remote control.
4. Settings carried out using remote control (optional)
Delay OFF time for light control
The time can be set infinitely variably at between 1 and 30 minutes.
Symbol TEST: 5 min.
The ON delay time avoids further multiple On and Off switching in the
area of brightness.
3
1
30 25 22
18
16
R1
10
TEST 1 3 6
2
2000
1200
600
200
40
Remote control LUXOMAT® IR-CdS
1. Check Battery:
open battery compartment by pressing the plastic springs together and
removing the battery-holder.
2. IMPORTANT
Please pay attention, that the setting is Potentio-meter 1 at “TEST” and
Potentiometer 2 not at “SUN”. All values which have been programmed using the remote control will be deleted in the event of power
failure in the position “TEST /SUN”. Please switch Potentiometer 2 over
to “MOON” or any other value.
Caution:
Settings with remote control override the potentiometer settings.
5. Option:
B.E.G.
6. Settings by remote control when open
LUXOMAT ®
DSI/
DALI
IR-CdS-DALI
+ +
- -
+
max
-
min
DSI/
DALI
1
min
5
min
10
min
15
min
30
min
ON
5
min
10
30
min min
60
min
OFF
LED
Resetting when
open: Deletes
all values set
with the remote
control, light
OFF.
IR-CdS
Unlocking device - Activation of
the programming mode
Lock device
Switching between DSI and
DALI program
Dimming the lights to the desired brightness value
Automatic reading in the
current light value as new
luminance set point
–
or
1
min
Set brightness value is saved
Dimming of the lighting on the
desired luminance value
or
+
RESET 10 0 h
7. Description of the key functions
30
min
to
t < 5s
Adjusting of the luminance set point
+ / – small steps
/
big steps
The procedure for leaving this mode is as follows:
+ –
50
Lux
Delay OFF time light
60
min
to
1500
Lux
max
ON
Permanent protection against sabotage
This function blocks the unit permanently (green LED is
illuminated). This operating mode can only be activated
during the period of 5 seconds after pressing the “lock“ button. This status will only permit actuating the function “Light
on/Light off”.
Follow-up time light
after button function
ON
100 h-stolving time active, stolving
time via potentiometerOFF
adjustable
LED-Display ON/OFF
1. Switch off the current
2. Apply current for 31 – 59 seconds
3. Switch of the current again
4. Apply current
5. Open detector
Light on /off when closed
The light will remain switched on/off for as long as the
follow-up time after button function is adjusted via the IRCdS. Permanent light by pushing the ON-button. The followup time can be set back by pushing the RESET-button.
The time can be reset with the RESET button.
Locking device – Exit
programming mode
Wall bracket for remote control
IR-CdS
t < 5s
LED flashes
Permanent protection against
sabotage
50
Lux
8. Wiring diagram
max
Standard mode with CdS-DALI/DSI
Schaltbild_CdS-DALI-DSI_270513.pdf 1 5/27/2013 12:45:22 PM
ON
L
N
OFF
L
N
DA
DA
N
L
L‘
1500
Lux
10. Article / Part nr. / Accessory
+
SM
FC
CdS-DALI/DSI
92563
92562
LUXOMAT® remote control:
IR-CdS (incl. wall bracket)
92577
Accessory:
BSK Ball basket guard
92199
Wall bracket for remote control as replacement92100
SM-Socket IP54
92161
E1
DALI/DSI
11. Technical data CdS-DALI/DSI
–
DA1
9. CdS-DAL I/DSI – Connections
L
N
L
N
DA –
DA +
L L L‘ L‘ N
Type
– +
CdS-DALI/DSI-SM
Sensor and power supply in one case
Power supply: 230 V~ ±10 %
Power consumption: < 1W
Ambient temperature: -25°C to +50°C
Degree of protection/class:SM/FC IP20, SM with accessory
IP54 / II
Recommended height for mounting: 2 - 3 m
Settings: locally and by remote control
Light values - IR-CdS: 10 - 2000 Lux
Light measurement: Mixed light, daylight + artificial light
Lux values-Potentiometer: 10 - 2000 Lux
• Switch contact
Type of contact: NOC
Contact load: 2300W cosφ=1 /
1150VA cosφ=0,5, µ-Contact
• DALI-Output
digital BUS control wire, 2-core, no polarity (broadcast only)
Max. no. of series-connected
electronic ballasts: up to 50 digital electronic dimmable
ballasts as a group.
Time-settings: 1 - 30 min.
Dimensions H x Ø [mm]SM
FC
CdS-DALI/DSI
48x 102 75 x 80
Visible portion when built into ceiling: 6 mm
WE RECOMMEND THAT BEFORE DIMMING OF THE CONNECTED
LIGHTS A 100 h BURN IN (T5 TUBES OR 80 HOURS FOR T8 TUBES)
FUNCTION TAKES PLACE.
THE LIFESPAN OF THE LAMPS CAN BE REDUCED IF THE BURN IN
DOES NOT TAKE PLACE.
12. LED-functional indicators
LED function indicators
Process
Initialisation time
unprogrammed
Initialisation time
programmed
Too bright detected
Standard mode
Double-locked
red flashes
red flashes quickly
green flashes 2x
each second
Too bright / too dark /
undefined in opened state
Switching DALI/DSI
DSI active
Switching DALI/DSI
DALI active
green flashes very
quickly
IR signal valid received
red shines 3 sec.
green flashes
quickly
green flashes
2x each
second
green flashes
very quickly
red shines 3 sec.
green shines 3 sec.
green shines
3sec.
green shines
IR signal invalid received
red shines 0,5 sec.
0,5sec.
red permaStolving phase active
red permanently on
nently on
Delay time switching-on
red flashes
red flashes quickly
active
quickly
red flashes 2x each red flashes 2x
Manuel switching / dimming
second
each second
Default
red and green lightning succes(Set Potentiometer on Sun
sively (10 sec. after setting the
and Test)
Potentiometer)
Declaration of Conformity: The product complies with
the low voltage recommendation 2006/95/EC and the EMV
recommendation 2004/108/EC.
L
N
DA +
DA –
+–
L‘ L N
CdS-DALI/DSI-FC
MAN 7682–CdS-DALI/DSI–EN–300813–1
L
N
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising