Manual 1200.1D EVO II REV 3.1_inglês.cdr

Manual 1200.1D EVO II REV 3.1_inglês.cdr
1200.1D EVO
Owner's Manual
English
INTRODUCTION
Dear customer,
Congratulations on acquiring your SounDigital!
You've just purchased a product of high quality and
technology. The SounDigital products are developed to
assure maximum efficiency and reliability to your sound
system.
Warning!
Ÿ
To prevent personal injuries or damage to the
amplifier,, read all the safety instructions written on
this manual;
Ÿ
If you have questions about the installation of this
equipment, get in touch with our tech support or with
a professional specialized in car audio installation;
Ÿ
Before proceeding with the installation of any
electric equipment on your vehicle, unplug the
negative (-) terminal of the battery to avoid fires,
injuries or damages;
Ÿ
Use your sound system safely, exposure to
continuous sound pressure over 85 dB may cause
irreversible hearing loss.
Class D Amplifiers:
The main characteristics of Class D amplifiers are:
audio quality, efficiency, versatility and compact design.
Here are the advantages of these characteristics:
Audio Quality – Class D amplifiers used to have a
limited response in the past and they used to have a
worse performance regarding higher frequencies than
Class AB amps, despite being more efficient.
Introducing new technologies, SounDigital developed a
Class D amplifier superior to the Class AB ones in
efficiency and performance.
Efficiency – The SounDigital Class D amplifiers have a
total efficiency (power source + output) higher than
70%, assuring a battery consumption and a heating
lower than the expected.
Versatility of uses –The flat response of all the
frequencies of SounDigital amplifiers allows them to be
used in all the kinds of systems: SPL, Sound Quality,
and Pancadao, meeting the needs with extreme quality.
Compact design – The high efficiency and technology
allow our amplifiers to be really compact, making it easy
to install them in vehicles where you have limited space.
IMPORTANT INFO
Read this manual and follow its instructions and
information carefully. It contains extremely important
information to have your amplifier working properly. If you
feel the need to contact our Tech Support, you can reach
our technicians through the e-mail
.
info@soundigitalusa.com .
We recommend the use of SounDigital original
accessories for a batter performance. The crossovers,
power supplies and voltmeters offered by SounDigital
follow the same quality standards as our amplifiers,
assuring an excelent quality and high power sound
system to our customers.
To know our complete line of amplifiers and accessories,
visit www.soundigitalusa.com .
This “Warning” sign alerts the user
of important info. Not following this
instructions may cause injuries to
the user or damage to the
equipment.
ADDITIONAL INFORMATION
PACKAGE CONTENTS
1 1200.1D EVO Amplifier
1 Owner’s Manual
1 Allen wrench 2.5mm
1 Allen wrench 4mm
1 Promotional Sticker
CONTACT CHANNEL
Customer Service
+1 786-600-1056
info@soundigitalusa.com
Tech Support
info@soundigitalusa.com
Website
soundigitalusa.com
Social Media
facebook.com/SounDigitalUSA
1
PANELS DESCRIPTION
1
3
2
9
4
10
5
11
6
7
12
8
13
14
15
16
17
2
PANELS DESCRIPTION
01
Audio Output RCA connector;
02
Audio Input RCA connector;
03
Variable Low Pass Filter control (50Hz - 500Hz);
04
Selector switch - low pass filter / filter off / audio mute;
05
Variable High Pass Filter control (5Hz - 60Hz);
06
Variable signal gain control;
07
Variable bass boost control (0dB - +12dB);
08
Variable bass reinforcement frequency control (35Hz ~ 70Hz);
09
Negative speaker connector (-);
10
Minimum speaker load allowed (impedance);
11
Positive speaker connector (+);
12
Positive power supply connector (+12V);
13
Remote power supply connector (REM);
14
Negative power supply connector (GND);
15
“Protection” LED indicator (Red);
16
“Clip” LED indicator (Yellow);
17
“Power On” LED indicator (Blue).
Declaration of Conformity
J. Anflor Eletrônicos - ME
Gravataí - RS
Brazil
Declare in own responsability that the products
described in this owner´s manual are in
compliance with technical standards:
- EN 60065:2002+A1:2002+A11:2008+A2:2010+A12:2010
- IEC 60065:2014-06
Juliano Anflor
J. Anflor Eletrônicos
Brazil
3
INSTALLATION
Eletrical Dimensioning
For proper operation your amplifier needs the correct
size of cables and batteries.
Warning!
The protection fuse or circuit
breaker must be installed at a max
distance of 30 cm (1 foot) from the
battery.
Minimum capacity of the battery
Recommend capacity of the battery
60A
Warning!
5 AWG/16mm²
Use good quality cables (copper if possible) for the
connections to the amplifier. CCAW cables should be
double the size (see table above).
Warning!
Securely mount the amplifier so that it does not
come loose in the event of a collision or a sudden jolt
to the vehicle. Avoid mounting it on metallic parts of
the vehicle, because it may cause an earth loop (you
might have noise issues).
63Ah
127Ah
Fuse/circuit breaker size
Size of recommended cable
Choose a proper place to install the amplifier and
avoid blocking the side ventilation panels.
Unplug the negative (-) terminal of
the battery before proceeding with
any electrical installation in the
vehicle to avoid fire starts, wounds
or damage to the amplifier.
Be careful when drilling holes in
the vehicle. Verify if you're not
drilling holes in the fuel tank,
brake lines or electrical cables of
the vehicle.
Use speakers accordingly to the power and impedance
of the amplifier. Verify if the adjustment filters can be
used to increase the performance of the equipment.
Warning!
Never use speakers with
impedance under the nominal
impedance of the amplifier or you
may damage it.
Installation Tips
The ground cable should be the shortest possible
and should be connected to the chassis of the
vehicle. The surface should be sanded at the
contact point to create a clean, metal-to-metal
connection between the chassis and the
termination of the ground wire.
Remove de paint between
the terminal and chassis
Keep the RCA cables together, but away from the
power or the audio output cables and away from
electric equipment such as electronic fuel injection
centrals, electric engines, etc.
Warning!
You should never connect or
disconnect RCA cables with the
amplifier on, because it may
damage the headunit or the
amplifier.
When passing cables through metallic walls, use
rubber grommets to avoid damage to the cable and
short circuits.
4
INSTALLATION
Fuse 60A
Unplug the negative (-) terminal of the battery before
proceeding with any eletrical installation in the vehicle.
OUTPUT
Output for additional
amplifier
To avoid unwanted noise in the system, join the
ground points of the equipment and audio output to
only one point.
After the end of the electrical installation, connect
the negative cable of the battery and, before starting
the audio system, check if all connections are
correctly done.
In order to adjust the gain, use the headunit volume
in 70% of its total, play a musical program of your
preference and turn up the gain until the clip led
blinks. Set the gain in a position where the “CLIP’’
LED doesn't blink.
Some headunits with strong signal output may
reach max power even when the gain is next to its
minimum. In that case, limit the volume of the
headunit right before the point where the clip led
starts blinking.
Warning!
Gain positioning over the correct
spot may cause noise, trigger
protection state or damage to the
speakers.
If you have any doubts, talk to the speaker's
manufacture.
The selection key only defines the low pass filter.
The high pass filter is always in action, regardless
the key position. (Unless it is in the "mute" position).
If you need to increase the bass response, adjust
the frequency and gain of the bass boost according
to your preference. Make sure the “CLIP’’ LED does
not blink with the new setting.
Adjust the Low and High pass filters according to
your preference and needs of the speakers.
5
6
LIMITED WARRANTY
SounDigital warrants the original purchaser that this product shall be free of defects in materials an workmanship for a
period of twelve (12) months from the original date of purchase. Some countries have extended warranty in case the
product is installed by an authorized dealer. This warranty is not transferrable and applies only to the original customer
from an authorized SounDigital dealer.
Warranty is void when:
Ÿ
Defect or problem caused by misuse of the product;
Ÿ
Incorrect installation or non-conformity with the Manual;
Ÿ
Maintenance made by unauthorized personnel;
Ÿ
Alteration or removal of the seal/serial number;
Ÿ
Exposure to adverse conditions (weather, humidity, etc);
Ÿ
Damage caused by fall, impact or natural depreciation, caused by transport and/or handling, risks, or smashings;
Ÿ
Products was purchased more than 12 months ago.
Warranty covers:
Ÿ
Component or material with manufacturing defects;
Ÿ
Workmanship/service needed to repair the
Ÿ
If you need service on your SounDigital amplifier, send it (freight-prepaid) to SounDigital's Amplifier Repair Center
through an authorized SounDigital dealer (must be accompanied by proof of purchase);
equipment;
Ÿ
Any extra information you can get by contacting us at the e-mail address: info@soundigitalusa.com;
Ÿ
In case of manufacturing defect or bad quality of raw material, the max compensation will be the replacement of the
product, not allowing any kind of compensation payment;
Ÿ New modifications/iterations on a product don't obligate the manufacturer to modify products formerly produced.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising