HDMI Extender over Single CAT5/6 with IR

HDMI Extender over Single CAT5/6 with IR
HDMI Extender over
Single CAT5/6 with IR/
RS-232 & Auto EDID
Quick Installation Guide
Introduction
The HDMI Extender over Single CAT5/6 with IR/RS-232
& Audio EDID supports is equipped with bi-directional
IR pass-through path and RS-232 serial port control.
These bonus features allow users to boost IR control
distance up to 100m (330ft) and makes IR control possible
through a single Cat5/5e/6 cable.
Features and Benefits
•
•
•
•
•
•
•
•
•
•
HDMI & HDCP compatible
Supports HDMI Deep Color & full 3D
Supports video solution up to 1080p at 60Hz
Extends HDMI signals up to 60m (200ft) from the
HDMI source at HD 1080i or 720p 24-bit
Extends HDMI signals up to 40m (130ft) from the
HDMI source at Full HD 1080p 24-bit
Supports uncompressed 7.1-channel or stereo digital
audio
Supports full frequency IR signal from 20KHz to
60KHz
Full Duplex RS-232 control up to 115,200 bps
Auto EDID learning feature
Allows cascading
04-0819A
1
Package Contents
•
HDMI Extender over Single CAT5/6 with IR/
RS-232 & Audio EDID kit (Tx & Rx units)
•
2x Power adapter
•
IR blaster extension cable
•
IR receiver extension cable
•
Quick installation guide
Layout
HDMI IN
MODE
DIP Switch
IR Receiver
IR Blaster
Figure 1: Transmitter Front Panel
•
Mode
A = EDID Full-HD (1080p@60)-24bit 2D video & 7.1ch audio
B = EDID Full-HD (1080p@60)-24bit 2D video & 2ch audio
C = EDID Full-HD (1080p@60)-24bit 3D video & 7.1ch audio
D = EDID Full-HD (1080p@60)-24bit 3D video & 2ch audio
E = EDID HD (1080p@30) (1080i@60) (720p@60)-24bit
2D video & 7.1ch audio
F = EDID HD (1080p@30) (1080i@30) (720P@60)-24bit
2D video & 2ch audio
G = EDID Full-HD (1080p@60)-36bit 2D video & 7.1ch audio
H = Auto EDID leaning
2
•
•
•
•
DIP Switch: Sets RS-232 serial communication
mode.
HDMI IN: Connects to an HDMI source with an
HDMI male-male cable.
IR Receiver: 3.5mm socket for plugging in the IR
receiver extension cable.
IR Blaster: 3.5mm socket for plugging in the IR
blaster extension cable.
+5V Power
Adapter
RJ45
RS-232
Figure 2: Transmitter Rear Panel
•
•
•
+5V Power Adapter: Connects to 5V DC Power
supply.
RJ45: Plug in a Cat5/5e/6 cable to be linked to the
receiver.
RS-232: Connects to PC serial port with a DB-9
Male-Male cable.
3
HDMI OUT
Signal Level
DIP Switch
IR Receiver
IR Blaster
Figure 3: Receiver Front Panel
•
•
•
•
•
Signal Level: Adjusts the equalization of the HDMI
signals for the best picture/sound quality. Turn the
rotary dial from Min (weakest) to Max (strongest)
until the audio/video is playing normally.
DIP Switch: Sets RS-232 serial communication mode.
HDMI OUT: Connects to an HDMI display with an
HDMI male-male cable.
IR Receiver: 3.5mm socket for plugging in the IR
receiver extension cable.
IR Blaster: 3.5mm socket for plugging in the IR
blister extension cable.
+5V Power
Adapter
RJ45
RS-232
Figure 4: Receiver Rear Panel
4
•
•
•
+5V Power Adapter: Connects to 5V DC power
supply.
RJ45: Plug in a Cat5/5e/6 cable to be linked to the
transmitter.
RS-232: Connects to serial port device with a DB-9
male-male cable.
IR Extenders
Figure 5: IR Blaster
•
•
Figure 6: IR Receiver
IR Blaster: Plug in the IR blaster to emit all IR
command signals received from the IR receiver
from the other end to control the devices
corresponding to the IR signals.
IR Receiver: plug in the IR receiver to receive all IR
command signals from the IR remote controls of the
corresponding devices
Note: Incorrect placement of IR Blaster and
Receiver may result in the failure of the IR
extenders. Please check carefully before plugging
in the IR extender to the respective IR sockets.
5
Specification of IR Earphone Jack
1. IR Signal [20-60kHz]
2. Grounding
Figure 7: IR Blaster
1. IR Signal [20-60kHz]
2. Grounding
3. Power
Figure 8: IR Receiver
Note: You can buy any IR extension cable that
meet the specification of the IR sockets if necessary
for replacement use. However, IR cables longer
that 2m (6-ft) may not work.
Application Diagram
Figure 9: Application diagram
6
Hardware Installation
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Power off all devices, including the source HDMI
device and display.
Connect your HDMI source (such as a Bluray Disc
player) to the transmitter's HDMI IN connector.
Connect the RS-232 cable (not included) to the
transmitter's RS-232 connector.
Connect the IR cable to the transmitter's IR connector.
Use the appropriate IR cable and socket depending
on the desired IR direction.
Connect your HDMI display (such as a LCD TV) to
the receiver's HDMI OUT connector.
Connect your Cat5/5e/6 LAN cable (do not use
crosscover LAN cable) between the transmitter and
receiver. Make sure the cable is securely connected
and not loose.
Connect the RS-232 cable (not included) to the
receiver's RS-232 connector.
Connect the IR cable to the receiver's IR connector.
Use the appropriate IR cable and socket depending
on the desired IR direction.
Plug one of the included power adapters into to the
+5V DC power jack of the transmitter, plug the
second power adapter into the +5V DC power jack
of the receiver, then plug both power adapters into
reliable power sources.
If you see flickering or blinking image on the display,
please adjust the Signal level switch to improve the
cable equalization. MAX stands for the strongest
HDMI signal level for short transmission length.
Please adjust the signal level from MIN to MAX and
stop turning the rotary switch whenever the audio/
video is playing normally. Inappropriate signal
level setting may cause overpowering issue that
would shorten the product life significantly!
7
Note:
1.
2.
3.
4.
5.
6.
7.
8
When adjusting the signal level on the receiver unit,
please dial the rotary control switch from MIN to
MAX and stop turning the rotary control whenever
the audio/video is playing normally. Inappropriate
signal level setting may cause overpowering issue
that would shorten the product life significantly!
Inserting the IR blaster and IR receiver into the
wrong 3.5mm infrared sockets may result in the
failure of the IR extenders. Please check carefully
before plugging in the IR extender to the respective
IR sockets.
If the DVI or HDMI device requires EDID information
from the connected display, please use EDID
Reader/Writer to retrieve and provide DVI or HDMI
display EDID information.
All HDMI over CAT5 transmission distances are
measured using Belden 1583A Cat5e 125MHz UTP
cable and ASTRODESIGN Video Signal Generator
VG-859C & VG-870B.
The transmission length is largely affected by the
type of Cat5/5e/6 cables, the type of HDMI sources,
and the type of HDMI display. The testing result
shows solid UTP cables can transmit longer signals
than stranded UTP cables. Shielded STP cables are
better suited than unshielded UTP cables. For long
extension applications, solid UTP/STP cables are
the only viable choice.
EIA/TIA-568-B termination (T568B) for Cat5/5e/6
cables is recommended for better performance.
To reduce EMI interference over long distances,
always use shielded STP Cat5/5e/6 cabling.
8.
9.
Use high quality Cat5/5e/6 cable, especially over
longer transmission distances. For resolution greater
that 1080i or 1280x1024, a CAT6 cable is
recommended.
If your HDMI display has multiple HDMI inputs, it
is found that the first HDMI input [HDMI input #1]
generally can produce better transmission
performance among all HDMI inputs.
9
Blank Page
10
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site
at www.siig.com and click Support. Our online support database is updated
daily with new drivers and solutions. Answers to your questions could be just
a few clicks away. You can also submit questions online and a technical support
analyst will promptly respond.
SIIG offers a 3-year manufacturer warranty with this product. This warranty
covers the original purchaser and guarantees the product to be free of any
defects in materials or workmanship for three (3) years from the date of
purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or
product having similar features and functionality) the product if defective in
materials or workmanship. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state. Please see our
web site for more warranty details.
If you encounter any problems with this product, please follow the procedures
below.
A) If it is within the store's return policy period, please return the product to
the store where you purchased it.
B) If your purchase has passed the store's return policy period, please follow
these steps to have the product repaired or replaced.
Step 1: Submit your RMA request. Go to www.siig.com, click Support,
then Request A Product Replacement to submit a request to SIIG RMA or
fax a request to 510-657-5962. Your RMA request will be processed, if the
product is determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s) and any
other accessories that came with the original package must be included.
• Clearly write your RMA number on the top of the returned package.
SIIG will refuse to accept any shipping package, and will not be
responsible for a product returned without an RMA number posted on
the outside of the shipping carton.
• You are responsible for the cost of shipping to SIIG. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•
SIIG will ship the repaired or replaced product via Ground in the U.S.
and International Economy outside of the U.S. at no cost to the
customer.
11
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by
adding A/V and Digital Signage connectivity solutions to our extensive
portfolio. All centered around the distribution and switching of A/V signals
over CAT5/6, these products include matrix switches, distribution amplifiers,
extenders, converters, splitters, cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to
providing high quality products while keeping economical and competitive
prices. High-quality control standards are evident by one of the lowest
defective return rates in the industry. Our products offer comprehensive
user manuals, user-friendly features, and most products are backed by a
lifetime warranty.
SIIG products can be found in many computer retail stores, mail order
catalogs, and e-commerce sites in the Americas, as well as through major
distributors, system integrators, and VARs.
PRODUCT NAME
HDMI Extender over Single CAT5/6 with IR/RS-232 & Auto EDID
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: 510-657-8688
HDMI Extender over Single CAT5/6 with IR/RS-232 & Auto EDID is a trademark of SIIG, Inc. SIIG and
the SIIG logo are registered trademarks of SIIG, Inc. All other names used in this publication are for
identification only and may be trademarks of their respective owners.
July, 2012
Copyright© 2012 by SIIG, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising