high performance square camera

high performance square camera
M076-DNR700-003
HIGH PERFORMANCE
SQUARE CAMERA
O P E R AT I O N M A N U AL
C AU T I O N S
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.”
WARNING -
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Caution -
Any changes or modifications in construction of this devies which are not
expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
CAUTION
Thank you for choosing our high quality camera.
Before attempting to connect or operate, please
r e a d a n d f o l l o w these instructions.
C O MPONENTS
C AU T I O N S
FEATURES
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European
countries with separate collection systems)
This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes
purchased this product, or their local government office, for details
of where and how they can take item for environmentally safe
recycling.
Business users should contact their supplier and check the terms
and conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.
1. A regulated DC12V 300mA power supply is recommended for use with
this camera for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to high
impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal
componets. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reflective light,
which may cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER(OR BACK). NO USER.
SERVICING TO QUALIFED SERVICE PERSONNEL.
MOUNTING POSITION
CONNECTION
This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient mangnitude to constitute
a risk of electric shock to persons.
TV MONITOR
RS-485(-)
LEAD WIRE
RS-485(+)
LEAD WIRE CONNECTION (STANDARD)
12V REGULATED
POWER SUPPLY
Screw 4ea
VIDEO IN
WHITE(RS-485(+))
BLACK(RS-485(-))
DIY CABLE CONNECTION
LEAD
cable
DIY
cable
This camera has realized high resolution of 600TV lines using the
top-notch full digital image processing, 10 Bit A/D serial signal
processing and special algorithm technologies.
• 3D DNR (3D Digital Noise Reduction)
The DNR technology eliminates noise thus generating a distinct
and clear image.
This camera DNR function utilizes an adaptive 3D Filter reducing
noise caused by movement.
• DAY&NIGHT
Day&Night operation feature an ‘auto’ mode which switches
between day and night mode automatically based upon the level
of illumination on the scene. And also, the COLOR mode operates
in daytime conditions to provide optimum colors, and B/W mode
operates in night-time conditions to enhance the definition of the
image.
Privacy masking allows for the ‘blanking’ of specific areas of a
scene, where the viewing or recording of images is prohibited or
undesired.
• OSD (On Screen Display)
This camera can easily controlled by multi-language OSD function
on the monitor screen.
DIMENSIONS
VIDEO IN
LEAD cable
(DIY cable)
• High Resolution 600TV Lines
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
Square
Camera
Operation
Manual
0.0001Lux(F2.0, 30 IRE, Sense-up X256, AGC high)
S/N Ratio 50dB
• Privacy Mask Function
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
12V REGULATED
POWER SUPPLY
Mounting
Bracket
• 1/3" 410K/470K Sony Super-HAD CCDⅡ
Minimum illumination
TV MONITOR
Unit(mm)
S P ECIFICATION
Signal Format
NTSC
Image Device
PAL
1/3" Sony Super HAD CCDⅡ
Total Pixels
811(H) x 508(V)
795(H) x 596(V)
Effective
Pixels
768(H) x 494(V)
752(H) x 582(V)
Inter. H/V
15,734/59.94Hz
15,625/50Hz
H.Resolution
600TV Lines
Minimum
illumination
Manual
Shutter
Sense-up
O S D M A N UA L
OSD MANUAL
GENERAL STRUCTURE
OSD FUNCTION DESCRIPTION
3. WHITE BALANCE
: Enable user to represent the accurate white color by controlling
the R.G.B level.
More than 50dB (AGC Off)
1/60 ~ 1/100.000 sec
1/50 ~ 1/100.000 sec
1/60(50), FLK, 1/250, 1/500, /2K, 1/5K, 1/10K, 1/100K
X2, X4, X8, X16, X32, X64, X128, X256
X2, X4, X8, X16, X32, X64, X128, X256
AGC
Off / Low / Middle / High
1.LENS
• MANUAL : Fixed for MANUAL Iris Lens.
SETUP MENU
LENS
EXPOSURE
WHITE BAL
• A T W •PUSH •PUSH-LOCK
• M A NUAL •INDOOR •OUTDOOR
DAY&NIGHT
• C O LOR
IMAGE
• F R EEZE •MIRROR •D-ZOOM
• S H ARPNESS •COLOR GAIN
• G A MMA •NEG.IMAGE •RETURN
3DNR
• L E VEL
•B/W
•AUTO
•RETURN
White
Balance
ATW / PUSH / PUSH-LOCK / MANUAL / Indoor / Outdoor
SPECIAL
Sync
System
• C A M TITLE •LANGUAGE •RS485
• M O TION •PRIVACY •SYNC
• R E TURN
Internal
RESET
• F A CTORY RESET •RETURN
8 Zone
EXIT
Privacy Zone
Flickerless
OFF/ON
Lens
Board Lens, Pinhole Lens, Varifocal Lens
3DNR
Off / On(Level setting)
Motion
Detection
4 Areas
Language
Standard: English, French, Russian,German, Spanish, Dutch
Option1: English, Chinese / Option2: English, Japanese
Etc.
Mirror(H,V,H/V), Digital Zoom, Freeze, Negative Image,
BLC, D-WDR, RS-485
Video Output
CVBS
Input Power
Source
DC12V ±10% Max 120mA
Operating
Temperature
-10˚C ~ +50˚C
WHITE BAL MANUAL
LENS
• S H UTTER • BRIGHTNESS • AGC
• S E NSE-UP • BLC • D-WDR
• R E TURN
0.0001 Lux / F2.0 ( Sens-up)
S/N Ratio
Electronic
Shutter
O S D M A N UA L
UP
MENU
(SELECTION KEY)
RIGHT
LEFT
DOWN
MANUAL
2. EXPOSURE
: Enable user to set up the function of SHUTTER, AGC,
SENSE-UP, BLC, D-WDR
EXPOSURE
- SHUTTER
SHUTTER
AUTO
• AUTO : Exposure is controlled
BRIGHTNESS
50
by established a standard.
AGC
OFF
• FLK : Enable user to set up the
SENSE-UP
AUTO
BLC
BLC┛
FLICKERLESS.
D-WDR
OFF
(NTSC: 1/100, PAL: 1/120)
RETURN
RET┛
• FIXED : Enable user to set up the
Shutter Speed.
> 1/60(50), 1/250, 1/500, 1/2K, 1/5K,
1/10K, 1/100K * ( ) is for PAL TYPE
- BRIGHTNESS : AUTO Mode Only.
- AGC : Low, Middle, High.
*If AGC feature is turned off,
3D-DNR & SENS-UP Features will not be able to use.
- SENSE-UP : Low-speed shutter control.
- BLC : The Function of Back Light Compensation.
• HSBLC : Highlight Suppression BLC will darken
image portions for clearer images.
- D-WDR : allows every detail to be captured accurately even if one
portion is bright while other portions are dark.
O S D M A N UA L
O S D M A N UA L
7. SPECIAL
: Setting up the CAM TITLE, LANGUAGE, RS485, MOTION,
PRIVACY, SYNC.
- PRIVACY : Privacy is the function that covers the some part on
screen to prevent private life Maximum 8 point covered.
• AREA SELECT : Enable user to set up a area from 1 to 8.
• AREA DISPLAY : Enable user to set up ON/OFF in selected area
• LEFT/RIGHT : Enable user to set up LEFT/RIGHT position in
selected area.
• WIDTH : Enable user to set up width in selected area.
• TOP/BOTTOM : Enable user to set up TOP/BOTTOM position in
selected area.
• HEIGHT : Enable user to set up height in selected area.
• COLOR : Enable user to set up MASK COLOR
- SYNC : Synchronization pulses for lock the viewing
monitor on the picture.
• INT : Internal Synchronization system
FREEZE
MIRROR
D-ZOOM
SHARPNESS
COLOR GAIN
GAMMA
NEG.IMAGE
RETURN
OFF
OFF
ON┛
5
┛
0.45
OFF
RET┛
- FREEZE : Setting of moving images in freeze-frame mode
- MIRROR
• MIRROR : Enable user to set up reversed LEFT and RIGHT image
• V-FLIP : Enable user to set up vertically flipped video.
• ROTATION : Enable user to set up 180-degree
rotation filp function.
- D-ZOOM : Enable user to expand one part of the monitor
screen for viewing.
- SHARPNESS : Enable user to set up sharpness control.
- COLOR GAIN : Enable user to set the RED GAIN or BLUE GAIN.
- GAMMA : Enable user to set up compensation
according to gamma value.
- NEG.IMAGE : Enable user to set up negative image ON/OFF.
6. 3DNR
: Three-dimensional noise reduction
- LEVEL : Enable user to set up noise reduction level.
3DNR
LEVEL
RETURN
50
RET┛
SPECIAL
CAM TITLE
LANGUAGE
RS485
MOTION
PRIVACY
SYNC
RETURN
OFF
ENGLISH
┛
ON┛
ON┛
INT
RET┛
- CAMERA TITLE : Display the title editing menu
- LANGUAGE :
Enable user to set up Language for OSD
• Standard: English, Russian, Spanish, German, French, Dutch
• Option1: English, Chinese / Option2: English, Japanese
- RS485
• CAM ID : Camera identification number
• BAUD RATE : Serial communication speed
(2400/4800/9600/19200/38400/57600 bps)
- MOTION : The camera monitors the movement of image,
and it sends an alarm signal or OSD icon.
• AREA SELECT : Enable user to select the 4 motion area.
• AREA DISPLAY : Enable user to set up ON/OFF in selected area
• LEFT/RIGHT : Enable user to set up LEFT/RIGHT position in
selected area.
• WIDTH : Enable user to set up width in selected area.
• TOP/BOTTOM : Enable user to set up TOP/BOTTOM position in
selected area.
• HEIGHT : Enable user to set up height in selected area.
• SENSITIVITY : Enable user to set up the movement detection
threshold value.
• MOTION VIEW : Display the motion area on the screen.
8. RESET
: Enable user to reset all of the status as the factory default
RESET
FACTORY
RETURN
24
32
RET┛
4. DAY&NIGHT
: Conversion of output image COLOR/BW depending on exterior
environment.
DAY & NIGHT AUTO
10sec
- AUTO : Color or B/W mode auto change DWELL TIME
DN LEVEL
4
• DETECT MODE
ND LEVEL
6
VIDEO : Select to detect mode as
RETURN
RET┛
level of VIDEO.
• DWELL TIME :
Time to protect susceptible
conversion of COLOR/BW (0~10 SEC).
• D>N LEVEL : Turnover level from
COLOR(Day) to BW(Night).
• N>D LEVEL : Turnover level from BW(Night) to COLOR(Day).
- B/W : Enable user to fix the output image in B/W.
• BURST ON/OFF : Select the burst signal ON/OFF when Night
condition.
- COLOR : Enable user to fix the output image in COLOR.
Pelco “D” Protocol Commands
O S D MANUAL
5. IMAGE
: Setting up the FREEZE, MIRROR, D-ZOOM, SHARPNESS,
COLOR GAIN, GAMMA, NEGATIVE IMAGE.
IMAGE
BLUE
RED
RETURN • ATW : Enable user to trace the
White Balance automatically
in the Wide range
(2,500K ~ 9,500K)
• PUSH : Enable user to trace the
White Balance automatically
in all the range.
• P-LOCK : Enable user to set up automatically
readjusted only at the request of the user.
• MANUAL : Enable user to set the RED GAIN or BLUE GAIN.
• INDOOR : Enable user to set up 3,200K base mode.
• OUTDOOR : Enable user to set up 5,400K base mode
RESET┛
RET┛
BYTE1 BYTE2 BYTE3 BYTE4 BYTE5 BYTE6 BYTE7
UP
0xFF
CamID
0x00
0x08
0x00
0x00
CS
DOWN
0xFF
CamID
0x00
0x10
0x00
0x00
CS
LEFT
0xFF
CamID
0x00
0x04
0x00
0x00
CS
RIGHT
0xFF
CamID
0x00
0x02
0x00
0x00
CS
SET
0xFF
CamID
0x02
0x00
0x00
0x00
CS
* Sync Byte : FFh(BYTE1)
* Address : Camera ID (1~255) (01h ~ FFh)
* Check sum : It is 8 bit(module 256) sum of the payload
bytes(BYTE2~BYTE6)
BYTE7 = BYTE2+…+BYTE6
ex) if BYTE2+…+BYTE6 = 1FCh, then BYTE7 = FCh
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising