Toshiba SD-M1711 Computer Drive User manual


Add to my manuals
18 Pages

advertisement

Toshiba SD-M1711 Computer Drive User manual | Manualzz

TOSHIBA AMERICA INFORMATION SYSTEMS

STORAGE DEVICE DIVISION

IRVINE, CALIFORNIA

SD-M1711

DVD-ROM SCSI DRIVE

USER MANUAL

CONTENTS

Introduction..............................................................................1

Setup ........................................................................................3

Using the DVD-ROM Drive ......................................................7

Troubleshooting.....................................................................10

Specifications ........................................................................11

Drive Connectors...................................................................15

INTRODUCTION – SD-M1711 DVD-ROM Drive

General Features

Tray Loading Mechanism

3-way Disc Eject (eject button, software, emergency eject hole)

Average Random Access Time

CD-ROM 85ms

DVD 105ms

DVD-RAM 170ms

DAE (Digital Audio Extraction) Audio Capability

MPC3 Compatibility

Headphone Output Volume Control

Multi-Read Capability

Regionalization (RPC2 compliance) (DVD)

SCSI BUS Interface:

Types of Disc Formats Supported

DVD

• DVD-ROM

DVD-5 - Single-sided/Single Layer

DVD-9 - Single-sided/Dual Layer

DVD-10 - Double-sided/Single Layer

DVD-18 - Double-sided/Dual Layer

• DVD-R, DVD-RW

1

CD

• CD-DA

• CD+(E)G

• CD-MIDI

• CD-TEXT

• CD-ROM

• CD-ROM-XA

• CD-I Bridge (Photo-CD, Video CD)

• CD-I

• Multi-session (Photo-CD, CD Extra, CD-RW, CD-R)

• CD-R (Read)

• CD-RW (Read)

Front Panel

Figure 1.SD-M1711 DVD-ROM Drive Front Panel

Loading Tray

Load disc using tray.

Busy Indicator

When you install a disc into the DVD-ROM drive, the BUSY light flashes slowly as it attempts to locate the disc. One of the following will occur:

• BUSY light goes out. The DVD-ROM drive is ready to read data from the disc.

• BUSY light flashes slowly. The disc may be dirty.

• BUSY light remains ON. The DVD-ROM is accessing data.

• BUSY light remains ON indefinitely. The DVD-ROM is experiencing an error

Eject

Button

The Eject button is used to open the disc tray so you can install or remove a disc.

Emergency

Eject Hole

The emergency eject hole is to be used only when the Loading Tray will not open when

Eject button is pressed.

SETUP – SD-M1711 DVD-ROM

The following steps must be performed to properly install your drive:

• Set DVD-ROM Drive Jumper Settings:

SCSI ID, Parity, Termination, 512/2K, Power

• Connect Audio Cable

• Attach SCSI Interface Cable

• Attach Power Cable

• Daisy-Chaining SCSI Drives (if applicable)

• Mount Drive

Jumper Settings

A block of mode select jumpers are located on the rear of the DVD-ROM. If a jumper covers both pins on the jumper block, it is ON; if there is no jumper or only one of the pins is covered, the jumper is

OFF. The jumper settings include SCSI ID, Parity,

Termination, Block Selectability, Test and Power

Supply.

Figure 2. Jumper Block

Figure 1. Jumper Location

SCSI ID - All SCSI devices attached to your computer are assigned a SCSI-ID number from 0 to

7. Your DVD-ROMs SCSI ID must be set so that its

ID number does not conflict with any other devices

SCSI-ID in your system. In most cases, your DVD-

ROM will be set to SCSI ID 4 at the factory. Also note that your SCSI interface card in most cases has a SCSI ID of 7. This following chart (figure 3) shows the jumper settings for the eight possible ID numbers

Figure 3. SCSI ID Examples

Parity - In the OFF mode, the parity bit check function on the SCSI data bus is activated which enhances data bus reliability. Therefore, the jumper should remain in the OFF mode.

3

Terminator ON/OFF - This jumper turns termination power ON or OFF. If you are connecting more than one SCSI device to your system, and the DVD-ROM is not at the end of the chain, then terminator jumper is not required.

512/2K (Block Size Selectability) - This jumper is used to select default block size. When the jumper is present, the default block size equals 512Bytes, when the jumper is not present, the default block size is

2048Bytes. This is effective for CD media only, not DVD media.

Test - This setting selects the drive operation between normal CD-ROM and CD-Audio player mode.

When jumper is set to ON position, commands from the host computer are ignored. This jumper is for test purposes only and should be set to OFF for proper CD-ROM function.

Power Supply - Toshiba SCSI DVD-ROM drives can supply power to other equipment on the SCSI

BUS. When the jumper is ON, the drive will supply termination power. If you are not sure if any other device supplies termination power, it is fine to leave the jumper ON.

Placing DVD-ROM Drive inside your Computer

Now that you have set the jumpers, you are ready to install your DVD-ROM drive inside your computer.

Important Note: Disconnect power from your computer system before beginning installation.

Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. If the DVD-ROM drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system.

Your Toshiba DVD-ROM drive can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vertically.)

Carefully start sliding the DVD-ROM drive into the opening with the disc tray facing the front of the computer. Before you push the drive all the way in you will need to connect the IDE BUS cable, Audio cable and the Power cable on the back of the drive.

Connecting Cables

SCSI Interface Cable (not supplied with drive) - The internal SCSI interface cable is connect to your

SCSI host adapter card and fits into the socket on the back of your DVD-ROM. The stripe or red-colored side of the ribbon cable connects to pin 1 of the drive's SCSI connector which is found next to the drive's power connector. Carefully push the SCSI connector into the socket, making sure it fits snugly

Power Cable - Connect an internal computer power supply cable to the power socket at the back of the DVD-

ROM drive. One side of the plug has chamfered edges, so the power connector fits only one way. Push plug completely into the socket making sure the plug fits correctly.

Figure 4.Installing Power Cable

4

Audio Cable (optional) - If you have a sound card and speakers, and would like to play audio CDs on your computer, you will need to install a CD/DVD audio cable.

Toshiba's DVD-ROM drives use a standard 4-pin audio cable that can be purchased from most local computer suppliers. The sound cable connects to your sound card at one end and the other end connects to the digital audio connector at the left rear of the DVD-ROM drive

(see DVD-ROM drive Back Panel photo for location).

Refer to the instructions that came with your sound card for details on any sound-driver software required.

Figure 5.Installing Audio Cable

Daisy-Chaining - If the DVD-ROM you are installing is one of two or more SCSI devices you are connecting to your system, you will need to use a custom built SCSI interface cable. Remember that the terminator jumper on the DVD-ROM drive must have the jumper installed when the drive is the last device in the chain.

Figure 6. Daisy-Chaining Multiple Drives

5

Completing Installation

After you have connected all the necessary cables, push the DVD-ROM drive completely into the computers drive slot. Mount drive per your computers instructions. The screw length should not exceed

30.5mm (measured from outside surface of side or bottom of drive to tip of screw). Replace computer cover and all outer screws.

Figure 7.Mounting Illustration

Software Driver - Toshiba's optical drives do not require any unique device drivers for Windows

'95/'98/2000/Me/XP/NT. After installing your drive and re-booting, your system should recognize your drive. Windows '95/'98/2000/Me/XP/NT Operating Systems support all Toshiba optical drives natively If you prefer using DOS, download the DOS ATAPI driver from our web site.

6

USING THE DVD DVD-ROM Drive – SD-M1711

Drive Operation

Inserting a Disc - Horizontally

To insert a disc into a drive that is mounted horizontally, perform the following steps:

Figure 1.Inserting Disc

1. Open the drive's Loading tray by pressing the Eject Button.

2. Place disc into drive's Loading tray

3. Press Eject button again or gently push on the open disc tray. Tray will automatically close.

Inserting a Disc - Vertically

To insert a disc in a drive that is mounted vertically, perform the following steps:

1. Locate sliding disc holders (4 locations) on drive's Loading Tray.

2. Position the disc behind the disc holders

3. Close the drive by gently pushing in the tray or pressing the eject button.

Figure 2.Inserting Disc Vertically

7

Removing a Disc

To remove a disc from the DVD-ROM drive, perform the following steps:

1. Open the Loading Tray by pressing the Eject Button.

2. Grasp disc by edges, and lift out of loading tray.

3. Press Eject Button again to close Loading Tray.

Usage Guidelines

• Keep the disc tray closed when not using the DVD-ROM Drive.

• Do not press down on the disc tray when opening or closing it.

• Do not place objects on the disc tray.

• Never use a damaged, broken, or deformed disc.

• Do not press the Open/Close button while the drive is playing a DVD movie or accessing a disc.

To stop a DVD movie, click Stop button in the DVD player application program.

NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of the disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high speed, causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high-speed technology and do not indicate a problem with the drive.

Emergency Ejection

CAUTION: The following procedure is intended only as a last resort when pressing the

eject button fails to open the Loading Tray

1. Turn computer power OFF by properly shutting down system.

2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push as shown in the picture below

3. DVD tray will open/eject.

8

Figure 3.Using Emergency Eject

This procedure cannot be repeated without cycling the DVD-ROMs (computer's) power.

After the media is removed and the loading tray is closed, the tray will not reopen without first turning the power ON/OFF.

NOTE: Use a bar that is less than 1.5 mm in diameter.

Do not insert more than 50mm in depth.

Inserting more than 50mm may damage the DVD-ROM drive.

Handling Media

DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVD movie skips or hangs during playback, clean the media. Most DVD video playback issues are media-related and can be remedied by proper handling and care of media.

Cleaning Media

Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc accessing speed.

If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather from the inner side outward.

9

TROUBLESHOOTING – SD-M1711

Problem

Disc tray cannot be opened

Drive is not recognized by system

Drive is not recognized by system during Boot process, but is recognized by the Operating

System (i.e. XP, Win2000, Win98,

Win NT, etc.)

BUSY Indicator LED flashes slowly

BUSY Indicator LED is constantly

ON

DVD-ROM can not play a DVD in the drive or certain types of CD media (i.e. CD-plus, etc.)

Solution

Check that there is power to drive.

Use Emergency Eject instructions to open tray.

Is the drive connected properly? Are all cables plugged in properly (e.g.

Power Cable, Interface Cable and Audio Cables).

Are the drive configuration jumpers on the DVD-ROM drive set properly?

Check to see that there is no SCSI ID conflict with another SCSI device connected to your system

Is the SCSI host adapter software driver loaded? On a step-by-step

(F8) Boot of the system is the DVD-ROM recognized?

(BIOS / DOS reports "device driver not found" or "no valid DVD-ROM drivers selected."). If not, Contact you SCSI host adapter manufacturer.

Has the DVD-ROM drive software driver been corrupted by a virus. Run a Virus Scan program and repair if possible. Contact Technical Support if the Virus renders the DVD-ROM drive software drivers not useable.

Is the SCSI host adapter software driver loaded? On a step-by-step

(F8) Boot of the system is the DVD-ROM recognized?

(BIOS / DOS reports "device driver not found" or "no valid DVD-ROM drivers selected."). If not, Contact you SCSI host adapter manufacturer.

Has the Windows DVD-ROM SCSI host adapter driver program been corrupted by a virus. Run a Virus Scan program and repair if possible.

Contact you SCSI host adapter manufacturer if the Virus renders the software driver not useable.

The disc may be dirty Clean it with a soft damp cloth. Avoid cleaning the disc using a circular motion. The disc should be wiped in a radial direction. That is, from the inner side outward.

The laser lens may have become cloudy or blocked by particulate matter. Please contact Technical Support.

Possible Hardware Problem. Please contact Technical Support.

Is the SCSI host adapter driver loaded

Is the DVD disc the correct format for the type of system that you are using? (i.e. on a PC an ISO9660 IBM compatible PC format as opposed to Apple/Mac HFS disc or UNIX disc formats which will not function).

Do you have the correct software applications program/drivers installed to run a DVD disc?

Has the Windows DVD-ROM drive software driver program been corrupted by a virus. Run a Virus Scan program and repair if possible.

Contact Technical Support if the Virus renders the software drivers not useable.

10

SPECIFICATIONS –SD-M1711

General

Interface SCSI

Compatible DVD-ROM Standards

DVD

CD CD-DA

CD-ROM

CD-I Bridge (Photo-CD, Video CD)

Multi-session (Photo-CD, CD Extra, CD-RW, CD-R)

CD-MINI

CD-TEXT

CD+(E)G

CD-ROM-XA

CD-I

CD-R (Read)

CD-RW (Read)

Storage Capacities

DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18)

DVD-R, DVD-RW, DVD-RAM

7.959GB (DVD-9)

8.754GB (DVD-10)

15.917GB (DVD-18)

3.679GB (DVD-R, Ver. 1.0)

4.377GB (DVD-R, Ver. 2.0)

2.324GB (DVD-RAM, Ver 1.0)

4.377GB (DVD-RAM, Ver 2.1)

748.8MB (mode 2)

Performance

Rotational Speed

DVD-ROM single layer dual layer

DVD-R/-RW (Ver 2.0)

DVD-R (Ver 1.0)

DVD-RAM (Ver 1.0)

DVD-Video CSS-disc

CD-ROM, CD-R/RW

CD-DA Transfer

CD-DA/Video CD

11

6,900rpm (5X - 12X)

6,300rpm (4.1X - 10X)

2,780rpm (2 - 4.8X)

3,200rpm (2 - 4.8X)

2,160 - 4,800rpm (2X)

2,780rpm (2 - 4.8X)

9,500rpm (20.7 - 48X)

1,800 - 4,300rpm (14 - 32X)

1,200 - 2,000rpm (4X - 7.8X)

Data Transfer Rate

DVD (Single)

DVD (Dual)

DVD-Video

DVD-R, DVD-RW

DVD-RAM ( Ver 1.0)

CD (mode 1)

CD-(mode 2)

Burst (SCSI Interface)

6,750 – 16,200 KBytes/s

5,540 - 13,500 KBytes/s

2,704 – 6,536 KBytes/s

2,704 – 6,536 KBytes/s

2,704 KBytes/s

3,105 – 7,200 KBytes/s

3,541 – 8,212 KBytes/s

Random Access Time

CD 95ms

DVD 85ms

DVD-RAM 170ms

Data Error Rate

DVD 10

-15

Max

CD 10

-15

Max (Mode 1)

10

-12

Max (Mode 2)

Spin-up Time

DVD-RAM (Ver 2.1) 1.5s Typ

Data Buffer

Reliability

192Kbytes

5,436 hours/year

313 cycles/yea

600,000 accesses/year

20% of Power ON time (Reading/Seeking)

Power ON Hours

ON/OFF Cycles

Number of Access

Operating Duty Cycle

Audio

Number of Channels

Frequency Response

Distortion

Output Levels

Headphone

2

20Hz to 20,000 Hz

-80 dB (at 1kHz JIS A-weighted)

12

Environmental

Ambient Temperature

Operating

Storage

Shipping

Temperature Gradient

5° to 50° C (41° to 122° F)

-10° to 60° C (-14° to 140° F)

-40° to 65° C (-40° to 149° F)

Relative Humidity

Operating

Storage/Shipping

Vibration

Operating

8% to 80%

5% to 95% (wet bulb 27 C max)

Non-operating no hard error: 10 to 500 Hz 2.45 m/s

2

[0.25G] (O-P)

(excludes resonance point) no damage: 5 - 10Hz 5mm (P-P)

10 - 500Hz 9.8m/s

2

[1G] (O-P)

Shock (Non-operating)

Acoustical Noise

490 m/s

2

[50G] (Half sine wave 11ms)

<45dB

Power

DC Voltage and Current Requirements 5V 5%, 12V 5%

+5V +5V

Idle (Laser ON, Motor ON)

Continuous Read (Data/Audio)

Standby (Laser OFF, Motor OFF)

Random Access (average)

470mA (DVD)

490mA (CD)

800mA (DVD)

850mA (CD)

110mA (DVD)

110mA (CD)

660mA (DVD)

760mA (CD)

300mA (DVD/CD) 0mA (DVD)

710mA (DVD)

720mA (CD)

680mA (DVD)

780mA (CD)

Physical

Connectors

DC input

IDE Interface Connector

Analog Audio Line Output Connector

13

AMP 1-480424-0 or equivalent

50 Pin SCSI (core type)

3 Pin Audio Connector

Lasers

CD Laser

Type

Wave Length

DVD Laser

Type

Wave Length

Semiconductor Laser and 3-beam System

770 - 795 nm

Semiconductor Laser and 1-beam System

770 - 650 nm

Regulatory

The SD-M1711 DVD-ROM drive has been certified by the following regulatory agencies:

• UL 1950

• CSA C22.2 No. 950

• TUV (EN60950I)

• CE standard

• CB

• DHHS 21 CFR Sub-Chapter J

14

DRIVE CONNECTORS –SD-M1711

Figure 1.SD-M1711 DVD-ROM Drive Rear Panel - Connectors

Power

Connector

Power is supplied to your DVD-ROM drive by the connection with your computer's

+5V/+12V power cable to the power socket at the back of drive. One side of the plug has chamfered edges, so the power connector fits only one way

CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in

upside-down with power ON

Audio

Connectors

SCSI

Connector

Supplies Analog sound to your system

The SD-M1711 DVD drive is connected to your computer system through the SCSI connector.

15

Table 1.Interface Pin Assignments

PIN

NO.

SIGNAL NAME PIN

NO

SIGNAL NAME

1 GND 2 -DB0

3 GND 4 -DB1

5 GND 6 -DB2

7 GND 8 -DB3

9 GND 10 -DB4

11 GND 12 -DB5

13 GND 14 -DB6

15 GND 16 -DB7

17 GND 18 -DBP

19 GND 20 GND

21 GND 22 GND

23 GND 24 GND

25 NO CONNECTION 26 TERM POWER (+5v)

27 GND 28 GND

29 GND 30 GND

31 GND 32 -ATN

33 GND 34 GND

35 GND 36 -BSY

37 GND 38 -ACK

39 GND 40 -RST

41 GND 42 -MSG

43 GND 44 -SEL

45 GND 46 -C/D

47 GND 48 -REQ

49 GND 50 -I/O

16

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement