User Manual Clipper Pro

User Manual Clipper Pro
材质:封面封底128G双铜 + 单色印刷
内页臻品上质80g高白纸 2个小号骑马钉
大约16页, 尺寸W 105 x H 75mm
1. AptX Low Latency
Contents
For a Better Experience
User Manual
1.
AptX Low Latency
1
2.
Product overview & basic operation
2
3.
What’s in the box?
4
4.
Pairing and connecting
5
4.1. Connecting to a mobile phone/tablet
5-6
4.2. Connecting to a Bluetooth transmitter
6-7
Clipper Pro
4.3. Connecting to two Bluetooth devices simultaneously
7-8
5.
How to reset to factory default setting?
8
6.
LED indications
9
Audio delay by transmitter type Transmitter support aptX Low Latency codec
aptX codec
SBC codec (most standard Bluetooth audio)
7.
Charging
10
8.
Product Specifications
11
www.avantree.com
A.
B.
C.
4.1. Connecting to a mobile phone/tablet
Step 1. Ensure Clipper Pro is off.
Step 2. Set Clipper Pro to PAIRING MODE (Press and hold MFB for 6 seconds
until the LED flashes BLUE and RED alternately).
Step 3. Activate Bluetooth on your phone/tablet and select “Avantree
Clipper Pro” to connect.
D.
Pair
Connect
Settings
3
Enjoy
Bluetooth
Bluetooth
Devices
A.
B.
C.
D.
E.
Avantree Clipper Pro
For a Better Experience
Avantree Clipper Pro
Avantree 3.5mm audio splitter *1
3.5mm audio cable *1
Micro USB charging cable *1
User manual & Quick user guide
User Manual
Wireless Receiver for Headphones
Clipper Pro
Hold MFB 6S
From off, hold for 6s, LED
flashes BLUE and RED
alternately
Activate Bluetooth, search
and select “Clipper Pro” to
connect.
6. LED indications
4.2. Connecting to a Bluetooth transmitter
Step 1. Ensure Clipper Pro is off.
Step 2. Set Clipper Pro to PAIRING MODE – Press and hold MFB for 6 seconds
until the LED flashes BLUE and RED alternately.
Step 3. Set your Bluetooth transmitter to PAIRING MODE**.
Step 4. Keep the devices close and wait for 5~30 seconds. Once connected, the
LEDs on both devices will slow down.
Stream music wirelessly
-6-
Status
Power on
LED indicator
LED flashes BLUE for 2 seconds
Power off
Pairing mode
LED flashes RED for 2 seconds
LED flashes BLUE and RED alternately
Connected
LED flashes BLUE once every 10 seconds
Disconnected
LED flashes BLUE twice every 10 seconds
Restore to default setting
LED flashes BLUE and RED together twice
(appears PINK)
Low battery
LED flashes RED once every 30 seconds
Charging
LED stays RED
Fully charged
Red LED turns off
7. Charging
8. Product Specifications
When the LED flashes RED, you should recharge the device. Please remove the
micro-USB protector and charge it. It normally takes around 2 hours to fully charge
the battery. The LED will stay RED when charging and will turn off when charging is
complete.
Charging Requirement
You can connect Clipper Pro via the supplied micro USB cable to your own USB
chargers (wall charger/travel charger/car charger, etc.) with 5V/500mA-1A or PC
USB port. It’s ok to use most mobile phone chargers on the market.
•
•
•
•
•
•
•
•
•
For a Better Experience
www.avantree.com
support@avantree.com
Z-PKMN-AS7L-V1
- 10 -
Charge from PC
MFB
BT version: 4.2
BT profile: A2DP, AVRCP, HFP, HSP
Audio codec: aptX Low Latency, aptX, SBC
Operational range: Class II, up to 10 meters
Working time: Up to 6 hours
Standby time: 100 hours
Charging time: 2 hours
Product weight: approx. 15g
Product size: 50.5*26*18mm
-2-
Connect
Pair
Set Clipper
pro to pairing
mode
- 11 -
Operation
Power on/off
Hold MFB for 2~3 seconds to turn Clipper Pro on/off
From off mode, press & hold for 6 seconds until the
LED indicator flashes BLUE and RED alternately.
Press MFB once when a call is incoming or in progress
Press & hold MFB for 2 seconds when a call is incoming
Double click MFB
Press once MFB when streaming music
Press V+ once
Press and hold
Press V- once
Answer/End a call
Reject a call
Last number redial
Play/Pause
Volume up
Next track
Volume down
Press and hold
Previous track
Mute ON
Press and hold V- for 1 second
Voice Dial (Siri)
Press V+ and V- together once
V+& V- Restore to
Press and hold V+ and V- together for 7 seconds, the
default settings
LED flashes BLUE and RED together ( appears PINK)
Note: Some functions may not work when used with different mobile phones or
other Bluetooth devices.
-3-
Microphone
Set transmitter
to PAIRING
MODE*
V+
V–
3
Enjoy
Keep them
close & wait
Step 4. Once connected, turn Clipper Pro off and on again. It will then
automatically reconnect to the two devices simultaneously.
Note: Once disconnected over 10 minutes, Clipper Pro will automatically power
itself off.
Once connected, the LEDs on Use your existing headphones
both devices will slow down.
to listen to the TV wirelessly
Dual Link
**PARING MODE: Discoverable mode for Bluetooth device, normally the LED
blinks quickly or flashes between two colors alternately.
4.3. Connecting to two Bluetooth devices simultaneously
Step 1. Connect the first Bluetooth device as above. Then turn off Clipper Pro.
Step 2. Set Clipper Pro to PAIRING MODE again – Press and hold MFB for 6
seconds until the LED flashes BLUE and RED alternately.
Step 3. Connect Clipper Pro to the second Bluetooth device as above.
5. How to reset to factory default setting?
Step 1. Turn on the Clipper Pro
Step 2. Press and hold the V+ and V- button for 5 seconds
Step 3. The Blue and Red LED will flashes twice then power off at the same time
-7-
-8-
Video user guide for Clipper Pro is available on Youtube.com
Telephone support: booking from Avantree.com
More FAQs and instructions on support.avantree.com
Email support: support@avantree.com
Avantree US Customer Serivce Line: 800 232 2078
Avantree Europe Customer Serivce Line: +1 408 600 0579
Note: The talk and standby times may vary when used with different mobile phones
or other devices and also defendent upon different usage styles, settings and
operating environment.
Charge from USB charger
-9-
Volume up (Next track)
LED indicator
Multi-function
button (MFB)
Hold MFB 6S, LED
flashes BLUE and
RED alternately
Function
Enter pairing mode
3.5 mm Audio jack
The audio delay will be
Around 40ms
Around 180ms
Around 250ms
Reconnect:
Whenever you turn Clipper Pro on again, it will automatically reconnect to your
phone.
-5-
-4-
Button
Micro USB port
www.avantree.com
E.
Volume down (Previous track)
-1-
4. Pairing and connecting
3. What’s in the box?
Avantree Clipper Pro is a Bluetooth audio receiver incorporating the latest “aptX low
latency” technology, for CD-like quality sound and with virtually no audio delay.
Ideal for games, watching TV and movies without lip sync delay.
To take advantage of the better performance offered by APTX low latency
codec, the other device must also support the same codec (Such as Avantree’s
Saturn Pro, Priva II, Leaf, etc). If the transmitter only supports the normal
AptX codec, or the SBC one, these codecs will be used instead.
Wireless Receiver for Headphones
Basic operation
2. Product overview & basic operation
Dispose of the packaging and
this product in accordance with
the latest provisions.
- 12 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising