BTR-160 / DPR-16C
BTR-160 / DPR-16C
GB
Version 1
GB
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SANGEAN
ELECTRONICS INC. is under license.
1
Controls and connections
BTR-160
2
DPR-16C
Controls and connections
1.Speaker
2. Mode button
3. LCD display
4. Info button
5. Menu button
6. Back button
7. Forward button
8. Standby button
9. Battery charge indicator/Low battery indicator
10. Tuning Control Rotary/Select/Seek knob
11. Volume button
12. Mute button
13. BTR-160:Preset 5/Fast-forward button
DPR-16C: Preset 5
14. BTR-160: Preset 4/Play/Pause button
DPR-16C: Preset 4
15. BTR-160: Preset 3/Rewind button
DPR-16C: Preset 3
16. Preset 2
17. BTR-160:Preset 1/Bluetooth pairing button
DPR-16C: Preset 1
18. Telescopic aerial
19. USB socket for software upgrade
20. Headphone jack
21. DC in jack
22. Battery compartment
23. Alkaline / NiMH / NiCad rechargeable battery switch
GB
3
4
Battery operation
Battery operation using rechargeable batteries
Battery operation using alkaline batteries
1.Remove the battery cover on the rear of the unit by pressing the
catch.
Note:
Before you insert the batteries, if you use non-rechargeable batteries,
make sure the NiMH/Alkaline switch which located inside the battery
compartment is switched to Alkaline position. If you use rechargeable
batteries, make sure to switch NiMH/Alkaline switch to NiMH position.
2.Insert 4 UM-1(D size) batteries into the spaces in the compartment.
3.Take care to ensure all batteries are inserted with correct polarity as
shown on the rear cabinet. Replace the battery cover.
4.Reduced power, distortion and a “stuttering sound” or low battery
LED indicator in red color is on are all signs that the batteries need
replacing or recharged.
5.If the radio is not to be used for any extended period of time, it is
recommended that the batteries are removed from the radio.
1.Slide the battery switch to the NiHM position.
2.Insert 4 UM-1 batteries into spaces in the compartment. Make
sure all batteries are inserted with the correct polarity as shown on
the rear cabinet. The radio is also designed to be used with NiMH
rechargeable batteries.
Note:
Do not use a mix of old and new rechargeable batteries.
Do not use a mix of full and empty rechargeable batteries.
Do not use batteries that have a different mAh capacity
Do not use damaged or leaking batteries
3.Make sure the radio is switched off and connected to the AC adaptor.
When the charge indicator flashes green indicating batteries are
charging. Batteries will be fully charged in around 10 hours. The
battery shows steady green light when the battery charging is
complete.
Note:
Duration for charging your battery fully can be varied according to
the mAh capacity of a battery. Higher mAh batteries required longer
charging time.
Important:
Under some conditions the charging LED indicator may switch off
after flashing briefly. This may happen if the batteries are already
freshly charged, or if the radio detects that you may be attempting
to recharge alkaline batteries or mixed different types or capacity of
rechargeable battery. In these cases the charging will be stopped.
Using the AC power adaptor
The AC power adaptor required for this unit should be 7.5 volts DC at 0.8A center pin positve.
Insert the adaptor plug into the DC socket on the left side of the radio.
Plug the adaptor into a standard mains socket outlet.
Whenever the adaptor is used, the batteries are automatically disconnected.
The AC adaptor should be disconnected from the main supply when not in use.
Navigation controls
This page describes the basic means of controlling your radio.
Instructions for each operating mode are given in the later section of this book.
1.Pressing the Standby button brings your radio out of Standby mode. Pressing Standby while
the radio is in use will cause it to return to the Standby mode with the clock display.
2.Pressing the Mode button gives you access to each of the operating modes: DAB+ radio, FM
radio and BLUETOOTH (available only in BTR-160).
3.Pressing the Menu button will access the menu system, whereas the Info button allows the
display of information relating to the radio station or music file being played.
4.Many operations require the user to make a selection from the menu. Highlight the menu item
using the Tuning Control Rotary on the right side of the radio. Press the Tuning Control
Rotary to select that item. If there are more than five items in a menu, then the display will
automatically scroll up or down so that the additional items become visible. If there are many
items in a menu, then the radio allows the menu to “wrap around” in either direction. This can
make it easier to reach items at the end of a long menu.
5.If an error is made when navigating the menus, it is generally possible to go back to a higher
level menu by pressing the Back button.
GB
1
2
3
3
4
5
5
Using the radio for the first time
1.Place your radio on a flat surface and plug the mains lead into the mains socket located on the
left side of your radio ensuring that the plug is pushed fully into the socket.
2.Plug the other end of the mains lead into the wall socket and switch on the wall socket.
IMPORTANT:
The mains adaptor is used as the means of connecting the radio to the mains supply. The
mains socket used for the radio must remain accessible during normal use. In order to disconnect the radio from the mains completely, the mains adaptor should be removed from the
mains outlet completely.
3.When you apply power, the display on the radio will light up and say: 'SANGEAN'. The first
time that you use your radio (or after Factory Reset) the display will show “Setup wizard” and
“YES” will be highlighted on the screen. Press the Tuning Control Rotary to start the setup
wizard. The screen will ask if you wish to run the setup wizard again at the next start up. This
will lead to the main menu.
4.Rotate the Tuning Control Rotary on the right hand side of the unit to highlight the desired
clock format (either 12 or 24 hour) then press the Tuning Control Rotary to enter your
selection. A menu allowing you to specify the auto update option for the clock will appear on
the display.
5.Rotate the Tuning Control Rotary to choose an auto-update option for the clock. This can be
updated from DAB or FM radio, or not updated. The default is to auto update from the DAB.
If you choose “No update” you will need to set the clock manually later( see the section of
‘Manually setting the clock’). Press the Tuning Control Rotary to confirm your choice.
3-5
WELCOME TO
DIGITAL RADIO
Setup wizard
Start now?
Time / Date
12/24 hour format
Auto update
Update from DAB
Update from FM
No update
Setup wizard
Run wizard again at
next start up?
*
6
*
DAB Radio
Using DAB mode for the first time
1.Carefully extend the telescopic aerial.
2.Press the Standby button to switch on the radio. If the radio has been used before the last
used mode will be selected.
3.Press the Mode button and rotate the Tuning control Rotary as needed so that DAB radio
mode is selected on the display. Press the Tuning Control Rotary to select the option.
4.If this is the first time that DAB mode is used a quick scan of the Band III DAB channels will be
carried out. The display will show 'Scanning'. (If the radio has been used before the last used
station will be selected instead.) During the scanning process, as new stations are detected
the station counter will increase and the stations will be added to the list which is stored in the
radio. The bar graph indicates the progress of the scan.
5.When scanning is completed the radio will list the stations found (in numeric-alpha order
0....9...A...Z), unless it has previously been tuned to a DAB station. Rotate the Tuning Control
Rotary to scroll through the list of available DAB radio stations. Press the Tuning Control
Rotary to select the highlighted station. The display may show 'Connecting...' while the radio
re-tunes. Press the Volume buttons to set the sound level as needed.
6.If the station list is still empty after the scan the display w ill show "No stations found". If
no stations are found it may be necessary to relocate your radio to a position giving better
reception.
2
GB
DAB
radio
DAB Radio
Scan
3
Stations: 24
Scanning
Station list
3.5
Heart
heat
Kerrang
Kiss
LBC
DAB
12:34
LBC
London’s Biggest
Conversation - LBC
5
7
Selecting a DAB radio station
1.When playing a DAB radio station, the display normally shows the name of the current station
with other related information.
2.Rotate the Tuning Control Rotary to access the radio station list and to scroll through the
available stations.
3.Press the Tuning Control Rotary to select the highlighted station. The display may show
‘Connecting...’ while the radio re-tunes.
4.Use the Volume buttons to set the sound level as needed.
Note:
If the display shows 'Station Not Available' it may be necessary to relocate your radio to a
position giving better reception. A question-mark in front of the station name merely indicates that
the station has not recently been detected by the radio. It may still be available.
2.3
DAB
12:34
Heart
More music variety on
Heart
Station list
4
Heart
heat
Kerrang
Kiss
LBC
DAB
LBC
Connecting...
Secondary services
Some DAB radio stations can have one or more secondary stations associated with them.
Typically these are not broadcast continually. If a station has a secondary station available then
the secondary will appear in the list of station names beneath the main (or primary) station.
Examples are the programs ‘Daily Service’ and ‘Parliament’ on BBC Radio 4.
1.To listen to a secondary service, rotate the Tuning Control Rotary to scroll to the chosen
station, and press the Tuning Control Rotary to tune to the station. If the secondary service is
not available (off-air) then the primary service will be selected.
8
Station list
1
BBC Radio 3
BBC Radio 4
Daily Service
?Parliament
BBC Radio 5 Live
12:34
Display modes
Your radio has a range of display options when in DAB mode:
1. Press the Info button to cycle through the different options.
a. Text
Displays text messages such as the artist or track name,
phone in number, traffic alerts, etc.
b. Program Type
Displays the type of station being listened to such as
Pop, Classic, News etc.
c. Multiplex Name / Frequency
Displays the name of the DAB multiplex to which
the current station belongs as well as its broadcast
frequency.
d. Signal error / strength
Displays the signal error and strength for the station
being listened to. A lower error number indicates a better
quality of radio signal. The signal strength graph can be
used when positioning the radio or its antenna. For good
reception the graph should occupy three or more blocks.
e. Bit rate and audio type
Displays the digital bit rate and audio coding information
for the station being listened to.
f . Date
Displays the current date.
A signal strength indicator is always shown in the lower area of the display on the right hand side.
If the broadcast being received is in stereo, then the stereo speaker symbol will be shown.
If the currently tuned station has been stored as a preset, then the preset number will also be
shown.
DAB
SHORT X-PAD
1
16:32
*** Short X-PAD”
DLS” Test Data fr
om VP-7664B by P
anasonic***
GB
DAB
SHORT X-PAD
16:32
News
DAB
SHORT X-PAD
16:32
Panasonic DAB SG
Freq:202.928 MHz
DAB
SHORT X-PAD
16:32
Signal Error: 0%
Strength:
DAB
SHORT X-PAD
16:32
Bit Rate:192 kbps
Codec: MP2
Channels: Stereo
DAB
SHORT X-PAD
16:33
Today’s Date:
2016/07/12
9
Finding new DAB radio stations
Should you wish to use your radio for DAB reception in a new location, or if no stations were
detected during the initial scan, you can follow this procedure to allow your radio to find out which
DAB radio stations are available.
1.Ensure that the telescopic antenna is extended, and then press the Mode button and rotate
the Tuning Control Rotary as needed to highlight DAB radio mode. Press the Tuning
Control Rotary to select the option.
2.Once in DAB mode press the Menu button.
3.Rotate the Tuning Control Rotary until 'Scan' is highlighted on the display.
4.Press the Tuning Control Rotary to initiate the scan. The display will show 'Scanning' and
your radio will perform a scan of the DAB Band III frequencies. As new stations are found the
station counter will increase and stations will be added to the list. The bar graph indicates the
progress of the scan.
DAB
1
Scan
2
3,4
10
Station list
Scan
Manual tune
Prune invalid
DRC
Stations: 24
Scanning
>
>
>
Manual Tuning
Manual tuning allows you to tune directly to the various Band III DAB channels (5A to 13F).
1.When in DAB mode press the Menu button so that the display shows the DAB menu.
2.Rotate the Tuning Control Rotary until 'Manual tune' is highlighted.
3.Press the Tuning Control Rotary to enter manual tune option.
4.Rotate the Tuning Control Rotary to choose the required DAB channel.
5.Press the Tuning Control Rotary to cause the radio to tune to the chosen channel. When
the radio has tuned, the display shows the channel number and frequ ency, and the name of
the DAB multiplex found (if any). A bar graph shows the signal strength and is useful if you
need to reposition the radio or its aerial. The minimum signal marker 'I' which separates the
left and right parts of the signal graph shows the minimum signal level required for satisfactory
reception. Any new radio stations found on the tuned DAB multiplex will be added to the list
stored in the radio.
6.Press the Back button to choose a different frequency.
7.Press the Menu button a second time to access the main DAB menu then select ' Station list'
to return to normal tuning.
DAB
1,7
Station list
Scan
Manual tune
Prune invalid
DRC
>
>
GB
>
Manual tune
2-5
11B 218.640 MHz
11C 220.352 MHz
11D 222.064 MHz
12A 223.936 MHz
12B 225.648 MHz
Manual tune
6
11C 220.352 MHz NOW Cam
Strength:
11
Dynamic Range Control setting
Dynamic Range Control (also known as DRC) can make quieter sounds easier to hear when
your radio is used in a noisy environment by reducing the dynamic range of the audio signal.
1.Press the Standby button to switch on your radio.
2.Press the Mode button and rotate the Tuning Control Rotary as needed to highlight DAB
radio mode. Press the Tuning Control to select the option.
3.Press the Menu button to enter the DAB menu.
4.Rotate the Tuning Control Rotary until 'DRC' is highlighted on the display.
5.Press the Tuning Control Rotary to enter the DRC adjustment mode. The current DRC
setting will be indicated with an asterisk.
6.Rotate the Tuning Control Rotary to highlight the required DRC setting (the default is Off).
'DRC high' - DRC is set as sent by broadcaster.
'DRC low' - DRC level is set to 1/2 that sent by broadcaster.
'DRC Off' - DRC is switched off, Broadcast DRC will be ignored.
7.Press the Tuning Control Rotary to confirm the setting.
Note:
Not all DAB broadcasts use the DRC function. If the broadcast does not provide DRC
information, then the DRC setting in the radio will have no effect.
1
DAB
radio
DAB
2
Station list
Scan
Manual tune
Prune invalid
DRC
>
>
>
DRC
DRC high
DRC low
DRC off
3
4-7
12
DAB Radio
*
Station order setup
Your radio has 3 station order settings from which you can choose. The station order settings
are, alphanumeric, ensemble and valid.
Note:
The default station order on your radio is alphanumeric.
1.Press the Standby button to switch on your radio.
2.Press the Mode button and rotate the Tuning Control Rotary as needed to highlight DAB radio
mode. Press the Tuning Control Rotary to select the option.
3.Press the Menu button to enter the DAB menu list.
4.Rotate the Tuning Control Rotary until 'Station order' is highlighted. Press the Tuning
Control Rotary to enter the station order adjustment mode.
5.Rotate the Tuning Control Rotary to choose between 'Alphanumeric', 'Ensemble' and 'Valid'.
'Alphanumeric' - sorts the station list alpha-numerically 0...9 A...Z.
'Ensemble' - organizes the station list by DAB multiplex.
'Valid' - shows only those stations for which a signal can be found.
The current setting is indicated by an asterisk.
6.Press the Tuning Control Rotary to select the required station order.
7.Press the Back button as needed to return to the DAB menu or to the stations list.
1
DAB Radio
DAB
radio
GB
DAB
2
Scan
Manual tune
Prune invalid
DRC
Station order
>
>
>
Station order
3
Alphanumeric
Ensemble
Valid
*
4-6
7
13
Prune stations
If you move to a different part of the country, some of the stations which were listed may no
longer be available. Also, from time to time, some DAB services may stop broadcasting, or may
change location or frequency. Stations which cannot be found, or which have not been received
for a very long time are shown in the station list with a question mark. The Prune stations function
will delete the marked DAB stations from your station list.
1.Press the Standby button to switch on your radio.
2.Press the Mode button and rotate the Tuning Control Rotary as needed to highlight DAB
radio mode. Press the Tuning Control Rotary to select the option.
3.Press the Menu button to enter the DAB menu.
4.Press the Tuning Control Rotary until 'Prune invalid' is highlighted. Press the Tuning Control
Rotary.
5.To cause the stations list to be pruned, eliminating unavailable stations rotate the Tuning
Control Rotary until 'YES' is highlighted on the display.
6.Press the Tuning Control Rotary to cause the invalid station names to be removed from
the station list. If you do not wish to prune stations, highlight 'NO' and then press the Tuning
Control Rotary. The display will revert to the previous menu.
Note:
If you have moved your radio to a different part of the country you should also carry out a search
for new stations (please see the section 'Finding new stations').
1
DAB
radio
DAB
2
Scan
Manual tune
Prune invalid
DRC
Station order
Prune invalid
3
4-6
14
DAB Radio
This removes all invalid
Stations, continue?
>
>
>
FM Radio
Operating your radio in FM mode
1.Carefully extend the telescopic aerial and press the Standby button to switch on your radio.
2.Press the Mode button and rotate the Tuning Control Rotary as needed to highlight FM radio
mode. Press the Tuning Control Rotary to select the option.
3.Rotate the Tuning Control Rotary in a clockwise direction. The displayed frequency will
increase. Press the Tuning Control Rotary to carry out an auto-tune. Your radio will scan
up the FM band from the currently displayed frequency and will stop scanning when it finds a
station of sufficient strength.
4.The display will show the frequency of the signal which has been found. If RDS information
is available, after a few seconds the display will show the radio station name. If you only hear
hiss or interference, simply press the Tuning Control Rotary to scan further. Your radio may
have found a spurious interference signal.
5.To find more FM stations press the Tuning Control Rotary to repeat the scan operation. To
scan down in frequency, rotate the Tuning Control Rotary in a anti-clockwise direction first
and then press the Tuning Control Rotary. Your radio will scan down the FM band from
the currently displayed frequency and will stop scanning when it finds a signal of sufficient
strength.
6.When the end of the waveband is reached your radio will recommence tuning from the
opposite end of the waveband. Use the Volume buttons to adjust the sound level as needed.
FM
104.90MHz
1
FM Radio
FM
V.H.B.N.
2
10:38
FM
radio
GB
10:39
FM Radio
2-5
6
15
Manual tuning
1.Carefully extend the telescopic aerial and press the Standby button to switch on your radio.
2.Press the Mode button and rotate the Tuning Control Rotary as needed to highlight FM radio
mode. Press the Tuning Control Rotary to select the option.
3.Rotate the Tuning Control Rotary to control the frequency that the radio will tune to. The
frequency will change in steps of 50kHz.When the end of the waveband is reached the radio
will recommence tuning from the opposite end of the waveband.
4.Use the Volume buttons to adjust the sound level as needed.
FM
104.90MHz
1
FM Radio
FM
V.H.B.N.
2
4
16
FM Radio
10:38
FM
radio
10:39
Display modes
Your radio has a range of display options when in FM mode:
1. Press the Info button to cycle through the different options.
a. Text
Displays text messages such as the artist or track name, phone in
number, traffic alerts, etc.
b. Program Type
Displays the type of station being listened to such as Pop, Classic,
News etc.
c. Frequency
Displays the frequency of the FM signal.
d. Date
Displays the current date.
Note:
If no RDS information is available, then the radio will only be able to display the frequency.
There will be no text or program type information available under these conditions.
The radio only provides displays when there is information available. So if there is no text, for
example, that display is not available.
The RDS indicator at the bottom of the display shows that there is some RDS data present in the
broadcast being received.
The stereo speaker display shows that the radio is receiving a stereo broadcast (please see also
'Stereo/Mono switching').
FM
V.H.B.N.
1
10:39
GB
FM Radio
FM
V.H.B.N.
10:43
Arts
FM Radio
FM
V.H.B.N.
10:42
106.50MHz
FM Radio
FM
V.H.B.N.
FM Radio
10:43
Today’s Date:
15/04/2014
17
Scan setting
When using the FM mode your radio can be set to either scan local stations or to scan all
stations including distant radio stations.
1.Press the Mode button and rotate the Tuning Control Rotary as needed to highlight FM radio
mode. Press the Tuning Control Rotary to select the option.
2.Press the Menu button to enter the FM menu.
3.Rotate the Tuning Control Rotary until 'Scan setting' is highlighted and then press the Tuning
Control Rotary to enter the scan adjustment mode. The current scan setting is indicated with
an asterisk.
4.To set your radio so that only the stations with the strongest signals are found during scanning
rotate Tuning Control Rotary until 'YES' is highlighted. Press the Tuning Control Rotary to
confirm the setting. (Normally this will restrict scanning to local transmissions.) Alternatively,
to set your radio so that all available stations are found during scanning (local and distant
transmissions) rotate the Tuning Control Rotary until 'NO' is highlighted. Press the Tuning
Control Rotary to confirm the setting.
FM
104.90MHz
1
FM Radio
10:38
FM
radio
FM
2
Scan setting
Audio setting
System setting
Main menu
FM station scan
Strong stations only?
3,4
FM station scan
Strong stations only?
18
>
>
Stereo / Mono switching
If the FM radio station being listened to has a weak signal, some hiss may be audible. It is
possible to reduce this hiss by forcing the radio to play the station in mono rather than stereo.
1.Press the Mode button. Rotate and press the Tuning Control Rotary as needed to select the
FM radio mode display and tune to the required FM station as previously described.
2.Press the Menu button to enter the FM menu.
3.Rotate the Tuning Control Rotary until 'Audio setting' is highlighted on the display. Press the
Tuning Control Rotary to enter the audio setting mode. The current setting is indicated with
an asterisk.
4.To switch to mono in order to reduce the hiss from a weak FM signal rotate the Tuning
Control Rotary until 'YES' is highlighted. Press the Tuning Control Rotary to confirm the
setting. Alternatively, to return to the normal automatic 'stereo or mono' mode press the
Tuning Control Rotary until 'NO' is highlighted. Press the Tuning Control rotary to confirm
the setting.
FM
104.90MHz
1
FM Radio
10:38
FM
radio
GB
FM
2
Scan setting
Audio setting
System setting
Main menu
>
>
FM weak reception
Listen in Mono only?
1,3,4
FM weak reception
Listen in Mono only?
19
Presetting stations in DAB and FM modes
There are 5 memory presets each for DAB and FM radio. They are used in the same way for
each operating mode.
1.Press the Standby button to switch on your radio.
2.Tune to the required radio station as previously described.
3.To store the station as a preset, press and hold the required Preset button (1-5) until the
display shows 'Preset stored'. The station will be stored under the chosen preset button.
Repeat this procedure as needed for the remaining presets.
4.Stations which are already stored in the presets may be over written by following the above
procedure.
Note:
The radio station presets are retained in memory when the radio is switched off and disconnected
from the mains supply.
Preset stored
Recalling a preset in DAB and FM modes
1.Press the Standby button to switch on your radio.
2.Select the required operating mode.
3.Momentarily press the required Preset button. Your radio will then tune to the station stored in
the selected preset memory. The chosen preset number is also shown in the lower area of the
radio display, e.g. '★4'.
FM
106.00 MHz
00:00
FM Radio
4
20
Listening music via Bluetooth streaming (available only in BTR-160)
You need to pair your Bluetooth device with your BTR-160 before you can auto-link to play/
stream Bluetooth music through your BTR-160. Paring creates a ‘bond’ so two devices can
recognize each other.
Pairing and playing your Bluetooth device for the first time
1.Press the Mode button and rotate the Tuning Control Rotary as needed to highlight
BLUETOOTH mode. Press the Tuning Control Rotary to select the option. The “Pairing” will
show on the display.
2.Activate Bluetooth on your device according to the device’s user manual to link to the
radio. Locate the Bluetooth device list and select the device named ‘BTR-160’ (With some
Smartphone’s that are equipped with earlier versions than BT2.1 Bluetooth device, you may
need to input the pass code “0000”)
3.Once connected, there will be a confirmation tone sound and the name of your connected
Bluetooth device will show on the display. You can simply select and play any music from your
source device. The volume control can be adjusted from your source device, or directly from
the radio.
4.Use the controls on your Bluetooth-enabled device or on the radio to play/pause and navigate
tracks.
Note:
1)If 2 Bluetooth devices are pairing for the first time, both must search for your radio, it will show
its availability on both devices. However, if one device links with this unit first, then the other
Bluetooth device won’t find it on the list.
2)If you take your source device out of range, the connection will be temporarily disconnected
to your radio. Your radio will automatically reconnect if the source device is brought back in
range. Be aware that during the period of disconnection, no other Bluetooth device can pair or
link with your radio.
3)If ‘BTR-160’ shows in your Bluetooth device list but your device cannot connect with it, please
delete the item from your list and pair the device with the radio again following the steps
described previously.
GB
BT
music
BLUETOOTH
Pairing...
00:00
21
4)The effective operation range between the system and the paired
device is approximately 10 meters (30 feet). Any obstacle between
the system and the device can reduce the operational range.
5)B luetooth connectivity performance may vary depending on
the connected Bluetooth devices. Please refer to the Bluetooth
capabilities of your device before connecting to your radio. All
features may not be supported on some paired Bluetooth devices.
6)With some mobile phones, making/receiving calls, text messages,
e-mails or any other activities unrelated to audio streaming may
mute the Bluetooth audio streaming or even temporarily disconnect
from your device. Such behavior is a function of the connected
device and does not indicate a fault with your BTR-160.
Display modes - Bluetooth
Your radio has a range of display options when in Bluetooth mode. Note
that the availability of information depends on the specific media format.
1. Press the Info button to cycle through the different options.
a. Artist
Displays the artist information for the track
currently playing.
b. Album
Displays the album information for the track
currently playing.
c. Date
Displays the current date.
d. Device name
Displays the device name for the track
currently playing.
22
Playing audio files in Bluetooth mode
When you have successfully connected your radio with the chosen
Bluetooth device you can start to play your music using the controls on
your connected Bluetooth device.
1.Once playing has started adjust the volume to the required setting
using the Volume control on your radio or on your enabled Bluetooth
device.
2.Use the controls on your device to play/pause and navigate tracks.
Alternatively, control the playback using Play/Pause (
), Next track
( ), Previous track buttons ( ) on the radio.
3.Press and hold the Fast-forward or Rewind button to move through
the current track. Release the button when the desired point is
reached.
Note:
Not all player applications or devices may respond to all of these
controls.
Playing a previously-paired Bluetooth source device
The BTR-160 can memorize up to 8 sets of paired Bluetooth source
devices, when the memory exceed this amount, the earliest paring
device will be over written from the device.
If your Bluetooth source device already paired with the BTR-160
previously, the unit will memorize your Bluetooth source device and it
attempts to reconnect with a Bluetooth source device in memory which
is last connected.
To connect to the required memorized Bluetooth device, you can also
press and release the Pair button to enter the Bluetooth device memory.
Then rotate the Tuning Control Rotary to find the desired memorized
Bluetooth device and press the Tuning Control Rotary to connect to
the required Bluetooth device.
Disconnecting your Bluetooth device
Press and hold the Bluetooth pairing button for 2-3 seconds to disconnect with your Bluetooth
device. You can also press the Mode button and rotate the Tuning Control Rotary to select any
mode other than Bluetooth mode and then press the Tuning Control Rotary or turn off Bluetooth
on your Bluetooth source device to disable the connection.
If you disconnect the Bluetooth device when you are in Bluetooth mode, the “Pairing” will show
on the display, indicating Bluetooth is available again for pairing.
GB
Clock and Alarms
Automatically updating the clock
You may specify that the radio sets its clock from DAB or FM radio broadcasts. After a power
failure the radio will then set its clock the next time that you turn on the radio in DAB or FM mode.
Alternatively you may specify that the time is not automatically updated. In this case the clock
must always be set manually after a power interruption.
1.With your radio switched on, press the Menu button to access the menu for the current mode.
2.Rotate the Tuning Control Rotary until 'System settings' is highlighted on the display. Press
the Tuning Control Rotary to enter the system settings menu.
3.Rotate the Tuning Control Rotary until 'Time/Date' is highlighted on the display. Press the
Tuning Control Rotary to enter the time setup.
4.Rotate Tuning Control Rotary until 'Auto update' is highlighted on the display. Press Tuning
Control Rotary to enter the auto-update menu.
5.Rotate the Tuning Control Rotary to choose an update option from 'Update from DAB',
'Update from FM', or 'No update' as required. Press the Tuning Control Rotary to confirm
your choice. The radio will then exit to the previous menu display.
System settings
1
Backlight
Equaliset
Time/Date
Inactive Standby
Language
>
>
>
>
Time/Date
2-5
Set Time/Date
Auto update
Set format
>
Auto update
Update from DAB
Update from FM
No update
*
23
Setting the clock format
The clock display used in standby mode and on the playing mode screens can be set to 12 or 24
hour format. The selected format is then also used when setting the alarms.
1.With your radio switched on, press the Menu button to access the menu for the current mode.
2.Rotate the Tuning Control Rotary until 'System settings' is highlighted on the display. Press
the Tuning Control Rotary to enter the system settings menu.
3.Rotate the Tuning Control Rotary until 'Time/Date' is highlighted on the display. Press the
Tuning Control Rotary to enter the time setup.
4.Rotate the Tuning Control Rotary until 'Set format' is highlighted on the display. Press the
Tuning Control Rotary to enter the clock format menu. The current clock display format is
marked with an asterisk.
5.Rotate the Tuning Control Rotary to select either 12 or 24 hour format. Press the Tuning
Control Rotary to confirm your choice of clock format. The display will then revert to the
previous menu. If the 12 hour clock format is chosen, the radio will then use the 12 hour clock
for the setting of alarms, and will display a 12 hour clock with an AM or PM indicator when in
standby mode.
24
System settings
1
Backlight
Equaliset
Time/Date
Inactive Standby
Language
>
>
>
>
Time/Date
2-5
Set Time/Date
Auto update
Set format
Set format
12/24 hour format
>
Manually setting the clock
1. Press the Standby button to switch on your radio.
2. To set all time settings press the Menu button to access the menu for the current mode.
3.Rotate the Tuning Control Rotary until 'System settings' is highlighted on the display. Press
the Tuning Control Rotary to enter the system settings menu.
4.Rotate the Tuning Control Rotary until 'Time/Date' is highlighted on the display, then press
the Tuning Control Rotary to enter the time and date setting screen.
5.Rotate the Tuning Control Rotary until 'Set Time/Date' is highlighted on the display. Press
the Tuning Control Rotary to enter the clock setup. The day digits will flash.
6.Rotate the Tuning Control Rotary until the correct day is shown on the display. Press the
Tuning Control Rotary to enter the selection. The month digits will then flash.
7.Rotate the Tuning Control Rotary to select the correct month. Press the Tuning Control
Rotary. The year digits will then flash.
8.Rotate the Tuning Control Rotary to select the correct year. Press the Tuning Control
Rotary to enter the selection. The hour digits will then flash.
9.Rotate the Tuning Control Rotary to select the correct hour. Press the Tuning Control
Rotary to enter the selection. The minute digits will then flash.
10.Rotate the Tuning Control Rotary to select the correct minutes. Press the Tuning Control
Rotary to enter the selection. The display will then return to the previous menu.
●If the radio has been set to use a 12 hour format, there will be an option here for setting
AM or PM for the clock time.
System settings
1
Backlight
Equaliset
Time/Date
Inactive Standby
Language
>
>
>
>
GB
Time/Date
Set Time/Date
Auto update
Set format
>
2
Set Time/Date
24-08-2010
13:53
3-10
Set Time/Date
24-08-2010
13:53
Set Time/Date
24-08-2010
13:53
Set Time/Date
24-08-2010
13:53
Set Time/Date
24-08-2010
13:53
25
Setting the alarm clock
Your radio has two separate alarms which can be set to wake you to either the radio or a buzzer
alarm. In the event of a power interruption your radio has built in memory that will retain your
alarm settings. Ensure that the time is set correctly before setting the alarms.
1.Press the Menu button and rotate the Tuning Control Rotary until ‘Main menu’ is highlighted.
Press the Tuning Control Rotary to enter the menu.
2.Rotate the Tuning Control Rotary until ‘Alarms’ is highlighted and the press the Tuning
Control Rotary to enter the selection.
3.Rotate the Tuning Control Rotary until the desired alarm (1 or 2) is highlighted on the display.
Press the Tuning Control Rotary to enter alarm setup.
4.Rotate the Tuning Control Rotary until 'Time' is highlighted on the display. Press the Tuning
Control Rotary to adjust the alarm time.
5.Rotate the Tuning Control Rotary to choose the alarm hour. Press the Tuning Control
Rotary to confirm the setting.
6.Rotate the Tuning Control Rotary to choose the alarm minute. Press the Tuning Control
Rotary to confirm the setting. The display will then return to the alarm setting menu. If the
radio has been set to use a 12 hour clock format, there will also be an option here for setting
AM or PM for the alarm time.
7.Rotate the Tuning Control Rotary to highlight 'Enable' and press the Tuning Control Rotary.
The display will show the Frequency options for the alarm. The alarm frequency options are as
follows:
'Off' - the alarm will be disabled
'Daily' - the alarm will sound everyday
'Once' - the alarm will sound once
'Weekends' - the alarm will sound only at weekends
'Weekdays' - the alarm will sound on weekdays only
Rotate the Tuning Control Rotary to choose the required alarm frequency option. Choosing
Off will disable the alarm. Press the Tuning Control Rotary to confirm the selection. If you
choose to set the alarm to Once you will also need to set the date using the Tuning Control
Rotary.
26
Alarms
Alarm 1: Off [00:00]
Alarm 2: Off [00:00]
1
Alarm 1
1-11
Enable:Off
Time: 00:00
Mode: Buzzer
Volume: 20
Save
Alarm 1 time
07:00
Alarm 1 frequency
Off
Dailf
Once
Weekends
Weekdays
Alarm 1 date/time
26-04-2016
07:30
Alarm 1 time
07:30
Alarm 1
Enable:Off
Time: 07:30
Mode: Buzzer
Volume: 20
Save
8.The alarm can be set to buzzer,DAB radio, FM radio. For whichever radio mode is selected,
the radio alarm may be set to any of the stations which have been stored as presets or to the
station most recently listened to. Rotate the Tuning Control Rotary to highlight the current
'Mode' option for the alarm, then press the Tuning Control Rotary if you wish to change it.
Rotate the Tuning Control Rotary to highlight either 'Buzzer' or the required mode. Press the
Tuning Control Rotary to confirm the selection.
9.If setting the alarm to a radio option, rotate the Tuning Control Rotary to highlight the
'Preset:' option then press the Tuning Control Rotary if you wish to change it. Choose from
either the radio station 'Last listened' to, or from the presets 1 - 5. Scroll to the chosen option
and press the Tuning Control Rotary to confirm the selection. Note that you can only set
the alarm to use a preset which has already been stored.
10.Rotate the Tuning Control Rotary until the 'Volume:' option is highlighted on the display and
press the Tuning Control Rotary if you wish to change it. The radio uses the saved volume
setting for each alarm when it sounds. Set the required volume using the Tuning Control
Rotary to confirm the setting.
11.In order to store the alarm settings rotate the Tuning Control Rotary until 'Save' is
highlighted. Press the Tuning Control Rotary to store the alarm settings. Your radio will
show 'saved' and will then go back to the list of alarms with the new alarm setting shown in
the display. If you decide not to save the settings, press the Back button. The display will
show 'Save changes' with a 'YES' or 'NO' option. Rotate the Tuning Control Rotary to choose
'NO' and then press the Tuning Control Rotary. 'Alarm not saved' will show on the display.
Active alarms are shown using small alarm indicators at the bottom of the playing displays
and on the clock display when in standby.
Note:
If you make a mistake at any point while setting the alarms, use the Back button to go back to
the previous screen.
Alarm 1
Enable:Once
Time: 07:30
Date: 26/04/2016
Mode: Buzzer
Volume:20
Alarm 1 mode
Buzzer
DAB
FM
Alarm 1
GB
Alarm 1
Time: 07:30
Date: 26/04/2016
Mode: FM
Preset: 1
Volume:20
Alarm 1 volume
Enable:Once
Time: 07:30
Date: 26/04/2016
Mode: FM
Preset: Last listened
Alarm 1 preset
Last listened
1. 104.90MHz
2.
90.00MHz
3.
98.00MHz
4. 104.90MHz
Alarm 1
Enable:Once
Time: 07:30
Date: 26/04/2016
Mode: FM
Preset: 1
Alarm 1
Date: 26/04/2016
Mode: FM
Preset: 1
Volume: 15
Save
Saved
27
When the alarm sounds
The buzzer or radio alarm will sound at the selected times for up to 60 minutes unless cancelled.
The volume used for the alarm will be as specified during the alarm setting procedure. If the
radio cannot connect to the specified radio station, the buzzer alarm will be used instead. To
cancel an alarm, press the Standby button to return to standby mode. The alarm icon will flash at
the bottom of the playing mode displays, and the radio will automatically switch back to standby
mode when the 60 minutes have elapsed.
Note:
If you have your earphone insert while the alarm is sounding, the sound of the alarm will come
out from your earphone.
Alarms
Alarm 1: On [07:30]
Alarm 2: Off [00:00]
1
17:31
Buzzer
1
Disabling alarms
1.To disable a single alarm enter the alarm setup menu and rotate the Tuning Control Rotary
until the desired alarm is highlighted on the display. Press the Tuning Control Rotary to
confirm.
2.Rotate the Tuning Control Rotary until the 'Enable:' option is highlighted on the display. Press
the Tuning Control Rotary.
3.Rotate the Tuning Control Rotary to highlight 'Off' and press the Tuning Control Rotary.
4.Rotate the Tuning Control Rotary until the 'Save' option is highlighted on the display then
press the Tuning Control Rotary to save the new setting. The chosen alarm will now be
disabled.
28
Alarm 1
1-4
Enable:Off
Time: 07:30
Mode: Buzzer
Volume: 20
Save
Snooze timer
1.The buzzer or radio alarm can be silenced for 5 minutes by pressing any button other than the
Standby button.
2.Should you wish for a longer snooze duration this can be extended. Press the Menu button to
access the menu for the current mode. Rotate the Tuning Control Rotary until ‘Main menu’ is
highlighted. Press the Tuning Control Rotary to enter the menu. Rotate the Tuning Control
Rotary until ‘Snooze’ is highlighted and press the Tuning Control Rotary to enter the setting.
Rotate the Tuning Control Rotary to select the desired snooze time. The options are
5,10,15,20,25,30 minutes. Press the Tuning Control Rotary to confirm the setting.
3.In order to cancel the Snooze timer while the alarm is suspended, press the Standby button.
The display will briefly show an 'Alarm Off' message.
17:32
Snooze
GB
1
Set snooze time
5MINS
Sleep timer
Your radio can be set to turn off after a preset time has elapsed. The sleep timer setting can be
adjusted between 15 and 120 minutes in 15 minute increments.
1.Press the Menu button and rotate the Tuning Control Rotary until ‘Main menu’ is highlighted.
Press the Tuning Control Rotary to enter the menu.
2.Rotate the Tuning Control Rotary until ‘Sleep’ is highlighted. Press the Tuning Control
Rotary to enter the setup. 'Sleep off' will appear on the display.
3.Rotate the Tuning Control Rotary to select the desired sleep time. The options are 15 to 120
minutes in 15 minutes increment. Use the OFF option to cancel the sleep function.
4.Your radio will switch off after the preset sleep time has elapsed.
5.Your radio will switch into standby mode after the preset time has elapsed. An active sleep
timer is shown using a small timer indicator at the bottom of the playing displays. This indicator
also shows the sleep time remaining before the radio switches itself into standby mode.
6.To cancel the sleep time before the preset time has elapsed and to turn off the radio, press
the Standby button to turn the unit off manually. To cancel the sleep timer and leave the radio
playing, go back into the sleep timer settings (steps 1 to 3 above) and select the Off option in
step 3. Alternatively, simply press the Standby button twice in succession to cancel the timer
and switch the radio back on again.
Set sleep time
Sleep Off
Set sleep time
15MINS
FM
98.90MHz
00:00
FM Radio
12
29
Inactive standby
Your radio can be set to standby mode automatically if it idles for a preset period of time. The idle
time setting can be adjusted between 2, 4, 5 and 6 hours.
1.Press the Menu button and rotate the Tuning control Rotary until 'System Settings' is
highlighted. Press the Tuning Control Rotary to enter the menu.
2.Rotate the Tuning Control Rotary until 'Inactive Standby' is highlighted. Press the Tuning
Control Rotary to enter the setup. Options for idle time will appear on the display.
3.Rotate the Tuning Control Rotary to select the desired idle time. Use the OFF option to
cancel the inactive standby function.
4.You radio will switch to standby mode when your radio idle for a preset period of time.
System settings
Backlight
Equaliser
Time/Date
Inactive Standby
Language
>
>
>
>
Timeout
Off
2 hours
4 hours
5 hours
6 hours
*
Mute function
Pressing the Mute button will mute the output from the loudspeakers.
1. Press the Mute button to mute the sound output.
2. Press the Mute button again or one of Volume buttons to un-mute the sound output.
Volume
1,2
30
Muted
Display and Audio
Equalizer function
The sound on your radio can be adjusted to suit your personal taste for the material that you are
listening to. The radio has a range of equalizer modes. Alternatively you may set the treble and
bass levels to your own preferences which can be accessed from the My EQ menu item.
1.Press the Menu button and rotate the Tuning Control Rotary until ‘System settings’ is
highlighted. Press the Tuning Control Rotary to enter the setup.
2.Rotate the Tuning Control Rotary until 'Equalizer' is highlighted on the display. Press the
Tuning Control Rotary to confirm.
3.Rotate the Tuning Control Rotary to cycle through and highlight the various modes. Press
the Tuning Control Rotary to confirm your selection.
a - Flat
b - Rock
c - Pop
d - Jazz
e - Classic
f - News
g - Movie
h - My EQ
The currently selected mode is marked with an asterisk.
FM
Scan Setting
Audio Setting
System settings
Main menu
GB
>
>
System settings
Backlight
Equaliser
Time/Date
Inactive Standby
Language
>
>
>
>
Equaliser
Flat
Rock
Pop
Jazz
Classic
*
31
Setting up your My EQ profile
If you find the preset equalizer functions not to your liking, you may set up a custom treble and
bass setting as follows:
1.Follow steps 1-2 in the previous section in order to enter the Equalizer menu.
2.Rotate the Tuning Control Rotary until 'My EQ profile setup' is highlighted on the display.
Press the Tuning Control Rotary to enter the adjustment mode.
3.To adjust the bass level rotate the Tuning Control Rotary until 'Bass' is highlighted on the
display. Press the Tuning Control Rotary to enter the adjustment mode and rotate the Tuning
Control Rotary until the desired level (between -14 and +14) is displayed. The sound will
change as you adjust the level. Press the Tuning Control Rotary when you are happy with
the bass setting.
4.To adjust the treble level rotate the Tuning Control Rotary until 'Treble' is highlighted on the
display. Press the Tuning Control Rotary to enter the adjustment mode and rotate the Tuning
Control Rotary until the desired level (between -14 and +14) is displayed. The sound will
change as you adjust the level. Press the Tuning Control Rotary when you are happy with
the treble setting.
5.To adjust the loudness rotate the Tuning Control Rotary until 'Loudness' is highlighted on
the display. Press the Tuning Control Rotary to enter the setting and repeatedly press the
Tuning Control Rotary to choose to activate or deactivate the loudness function.
6.Press the Back button and the display will prompt you to save the changes. If you wish to
save the changes highlight 'YES'. If you do not wish to save the changes highlight 'NO'. Press
the Tuning Control Rotary to enter the selection.
7.To use the 'My EQ' profile rotate the Tuning Control Rotary until 'My EQ' is highlighted, and
then press the Tuning Control Rotary to make the selection. The treble and bass settings will
be remembered for the next time that you wish to use the 'My EQ' setting.
32
Equaliser
Classic
News
Movie
My EQ
My EQ profile setup
My EQ profile setup
Bass:
Treble:
Loudness:
Bass
Treble
0
0
OFF
>
Brightness control
The brightness of the display can be adjusted for when the radio is in standby and for when it is
in use. If you use the unit in the bedroom, you may prefer a lower standby brightness level than a
higher brightness setting.
1.Press the Standby button to switch on your radio. Access the menu for the current mode by
pressing the Menu button.
2.Rotate the Tuning Control Rotary until 'System settings' is highlighted on the display. Press
the Tuning Control Rotary to enter the system settings menu. Rotate the Tuning Control
Rotary until 'Backlight' is highlighted on the display. Press the Tuning Control Rotary to
confirm the setting.
3.In Backlight menu, there are 2 settings:
On level: to adjust the brightness when the radio is in use.
Dim level: to adjust the brightness when the radio is in standby.
Rotate the Tuning Control Rotary to select your option and press the Tuning Control Rotary
to confirm your setting.
FM
Scan Setting
Audio Settting
System settings
Main menu
>
>
System settings
Backlight
Equaliser
Time/Date
Inactive Standby
Language
GB
Backlight
>
>
>
On level
Dim level
>
>
Language selection
By default your radio will display all menus and messages in English. You can choose your
preferred language.
1.Access the menu for the current mode by pressing the Menu button. Rotate the Tuning
Control Rotary until 'System settings' is highlighted on the display. Press the Tuning Control
Rotary to enter the settings menu.
2.Rotate the Tuning Control Rotary until 'Language' is highlighted on the display. Press the
Tuning Control Rotary to enter the menu.
3.Rotate the Tuning Control Rotary until your preferred language is highlighted and press the
Tuning Control Rotary to confirm the setting.
FM
Scan Setting
Audio Settting
System settings
Main menu
>
>
System settings
Backlight
Equaliser
Time/Date
Inactive Standby
Language
Language
>
>
>
>
English
Francais
Deutsch
Italiano
Dansk
*
33
Headphone socket
A 3.5mm Headphone Socket located on the left hand side of your radio is provided for use with
headphones. Inserting a plug automatically mutes the internal loudspeaker.
Please be aware that the sensitivity of headphones can vary widely. We therefore recommend
setting volume to a low level before connecting headphones to the radio. It is also recommended
to reduce the volume before unplugging your headphones.
IMPORTANT:
Excessive sound pressure from earphones and headphones can cause hearing loss.
To prevent possible hearing damage, do not listen at high volume levels for long periods.
34
Information
Factory reset
If you wish to completely reset your radio to its initial state this may be performed by following
this procedure. By performing a factory reset, all user entered settings will be erased.
1.Access the menu for the current mode by pressing the Menu button. Rotate the Tuning
Control Rotary to highlight the 'Main menu' option, then press the Tuning Control Rotary to
confirm.
2.Rotate the Tuning Control Rotary until 'System settings' is highlighted and then press the
Tuning Control Rotary to confirm the setting.
3.Rotate the Tuning Control Rotary until 'Factory Reset' is highlighted and then press the
Tuning Control Rotary to confirm the setting. Rotate the Tuning Control Rotary to highlight
'YES' to proceed. If you do not wish to carry out a system reset, highlight 'NO' and then press
the Tuning Control Rotary to confirm the setting. The display will revert to the previous menu.
4.With 'YES' highlighted, a full reset will be performed and the radio will restart as if first plugged
in. The DAB stations list together with any preset stations will be erased. All configuration
settings will be restored to their defaults,the clock and alarms will be reset.
In case of malfunction for any reason, reset the product as described above to resume normal
operation. It may be necessary in some cases to disconnect the mains power, then reconnect
power after 10 seconds. In case of malfunction due to electrical fast transient (burst), reset
the product as above (reconnection of the power source may be required) to resume normal
operation.
System settings
Equaliser
Time/Date
Inactive Standby
Language
Factory Reset
>
>
GB
>
Factory reset
Proceed?
Restarting...
WELCOME TO
DIGITAL RADIO
Setup wizard
Start now?
35
USB socket for software upgrade
From time to time, new software features for your radio may be developed. Your radio has
therefore been designed to allow its internal software to be updated using your USB upgrade
port.
You should not attempt to update your radio unless it is recommended to you by Sangean
Customer Services. Updating the software may remove radio station presets and alarm settings
from your radio.
Software updates for your radio may be available in the future.
As software updates become available software and information on how to update your radio can
be found at:
http://sg.sangean.com.tw/first/first.asp
http://www.sangean.eu/first/first.asp
www.sangean.com.au
For more information, please contact our Head Office by sending an email to info@sangean.com
1.Using the micro USB cable (not supplied) to connect the USB socket on the left hand side of
the radio and your PC USB port.
2.Go to the website above to download the latest software. Follow the on-screen instructions on
your PC provided with the upgrade software to complete the software upgrade.
Software version display
The software version display is provided for reference and customer support purposes and
cannot be changed.
1.Access the menu for the current mode by pressing the Menu button. Rotate the Tuning Control
Rotary until 'System settings' is highlighted on the display. Press the Tuning Control Rotary
to enter the System settings menu.
2.Rotate the Tuning Control Rotary until 'Info' is highlighted on the display. Press the Tuning
Control Rotary to display the software version.
36
System settings
Inactive Standby
Language
Factory Reset
Setup wizard
Info
>
Cautions
Do not allow your radio to be exposed to water, steam or sand.
Do not leave your radio where excessive heat could cause damage.
The name plate is located on the rear of the radio.
●T he radio shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the radio.
●I t is recommended to operate the product such that there is a
minimum distance (10cm recommended) to adjacent objects in order
to ensure good ventilation.
●The ventilation of the product should not be restricted by covering it
with items such as newspapers, tablecloths, curtains etc.
●No naked flame sources such as lighted candles should be placed on
the product.
●It is recommended to avoid using or storing the product at extremes
of temperature. Avoid leaving the unit in cars, on windows sills, in
direct sunlight etc.
● The radio must be used in a moderate climate.
●The apparatus shall not be exposed to dripping of splashing and that
no objects filled with liquids, such as vases, shall be placed on the
apparatus.
●T he batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
●The MAINS plug or an appliance coupler is used as the disconnect
device, the disconnect device shall remain readily operable.
37
GB
Specifications
Power Requirements
Mains Power Supply
Batteries
Frequency Coverage
FM
DAB
Circuit features
AC 100- 240 V/50/60 Hz/12W
4 x UM-1(D size, LR20), Alkaline or NiMH
battery
Output power
Headphone socket
Aerial System
DAB
FM
1W
3.5 mm diameter, stereo
Telescopic aerial
Telescopic aerial
87.5 - 108 MHz
174.928 - 239.200 MHz
Bluetooth (available only in BTR-160)
Bluetooth specification
Bluetooth® 4.1 EDR compliant
Profile Support
A2DP, AVRCP
Bluetooth Audio CODEC
AAC, SBC
Transmitting Power
Power Class 2
Line of sight range
10 meters/30 feet
The company reserves the right to amend the specification without notice.
Different model names are applied according to various market areas.
If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be disposed
of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. (Waste
Electrical and Electronic Equipment Directive)
38
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising