System Remote Control SR
™
System Remote
Control SR-150
Setup Guide
Batterien.
• Versuchen Sie nicht, eine Batterie neuzuladen, es sei denn die Batterie
ist spezifisch gekennzeichnetes „nachladbares.“
• Entledigen Sie nie sich Batterien in einem Feuer.
Configure the Remote Control
1
Start Composer and connect to a Director.
2
In the System Design view, (selected by default), select the room where the
System Remote Control will reside.
3
In the My Drivers tab, locate the SR-150 under the User Interface section.
Use and Features
Control4 System Remote Control SR-150 (Model C4-SR150B-Z-B) is intended for
use in a Control4® system using OS 1.8.2 and later. This System Remote Control can
be used to:
• Navigate system menus and access media databases on a television or
monitor
• Control system devices
The properties include:
• Keypad Brightness—Set the light level (brightness) of the keypad backlight.
Choose a percentage from 0 (Off) to 100 (full brightness).
• Sleep Mode—Set how long the System Remote Control stays awake after
no activity. The default setting is 15 seconds, but can be extended up to 60
seconds or can be reduced down to 0 to conserve battery life. Select wake on
movement to wake the remote when picked up.
• Batteries—Displays the current strength of the batteries.
• Network:
MAC—Displays the System Remote Control’s own MAC address.
This System Remote Control goes beyond a typical “universal” remote that simply
learns IR codes from TVs, VCRs, CD players, and DVD players. This device features:
•
•
•
•
•
•
•
Bi-directional communication with system components
ZigBee wireless mesh networking
Full access to system components
Back-lighting on keys for ease of use in dark rooms
Quick-access buttons to select recently used audio and video devices
Programmable buttons
Standard control features for: Digital Satellite Systems (DSS), cable boxes, TV
tuners, Digital Video Recorders (DVR), DVD changers/players, CD changers/
players, MP3 players, VCRs, or TVs.
• Powered by four (4) AAA batteries (included)
Install and Maintain the Batteries
4
Double-click SR-150 to add the device to the project tree.
5
Identify the SR-150:
•
•
•
•
In the Connections view, click the Network tab.
Select System Remote Control SR-150 in the center pane.
Click Identify (or right-click and choose Identify).
When prompted to do so, press the red 4 button four (4) times to have the
device identify to the Control4 system.
• Check ZigBee Channel—To determine the current ZigBee channel: Press
Room Off, #,*,7,4,7 then count the blinks of Room Off. The number of blinks
corresponds with the channel number.
• Reset to Factory Defaults—To reset all settings to the factory defaults and
leave the ZigBee network: Press Room Off, #,*,1,3,4,1,3.
Program the Programmable Buttons
Battery Use and Care Tips
On the System Remote Control SR-150, you can program six (6) soft buttons (Red,
Green, Yellow, Blue, *, and #) to perform programmed activities. These buttons can
be programmed to execute any of the AV device’s macros or IR codes. Program
these options using the AV device Properties page.
• Keep the battery contacts and compartment clean.
• Remove the batteries from the product if it is not going to be used for
several months.
• Extreme temperatures reduce battery performance. Avoid putting the SR-150
in very warm places.
Battery Replacement and Safety Rules
CAUTION! To prevent a battery short, leakage or rupture:
• Use typical AAA Alkaline batteries only.
• Do not mix battery types, such as Alkaline and rechargeable
NiMH batteries.
• Do not attempt to recharge a battery unless the battery is specifically
marked “rechargeable.”
• Never dispose of batteries in a fire.
ATTENTION! Pour empêcher court-circuiter, fuite ou rupture de batterie:
Utilisez les accumulateurs alcalins typiques d’AAA seulement.
• Ne mélangez pas les types de batterie, tels que les batteries alkalines
et rechargeables de NiMH.
• N’essayez pas de recharger une batterie à moins que la batterie soit
spécifiquement marqué « rechargeable ».
• Ne vous débarassez jamais des batteries dans un feu.
• Ne vous débarassez jamais des batteries dans un feu.
VORSICHT! Das Batteriekurzschluß, -durchsickern oder -abbruch
verhindern:
• Benutzen Sie AAA alkalische Batterien nur im Schalter.
• Mischen Sie nicht Batteriearten, wie alkalische und nachladbare NiMH
Note: To complete the identification process, the System Remote Control
must be on the same ZigBee channel as the Controller; the Controller must
have Zserver enabled. If you need to change the ZigBee channel on the
System Remote Control, see Step 7.
• When the MAC address appears in the window, click Close.
6
View or change the System Remote Control properties as needed in
Composer. In the System Design view’s project tree, select the System
Remote Control SR-150 object to display the device’s properties.
• Select the System Design view.
• Select an AV device to display the device’s Properties page.
• On the device’s Properties page, choose Code or Macro for the button you
want to program, and then choose a code or macro from the drop-down list,
edit the Help text as needed, and then choose Set.
NOTE: Help text describes custom programming to end-users under the
House option in any of the Navigators.
Firmware Version—Displays the current firmware version.
• Watch/Listen Button Behavior—Select to start the most recently-used
device.
7
Change System Remote Control settings as needed at the SR-150 remote by
using the applicable button-press sequence:
Install the Batteries
Install the four (4) AAA batteries (included) into the back of the SR-150. Insert
them according to the diagram provided in the battery compartment (with the +
and - terminals aligned correctly).
Based on AV device (pictured):
1
Start Composer and connect to a Director.
2
Ensure the System Design view is selected.
3
Ensure that you have the following devices in your project:
For example:
(1) In System Design view, select Disc Changer.
(2) Under Red button, choose Code.
(3) From the drop-down list, choose Subtitle.
(4) Choose the Set button to create a Subtitle button.
Based on room:
Select the Programming view.
Select a room in the Device Events pane.
Select the Commands radio button in the [Room] Events pane.
Use the drop-down menu to select a command or button (such as “Blue
Button”).
• Build the script using items from the Actions pane to program the actions
desired in the selected room when you select the command or button.
•
•
•
•
For more information about programming, see the Composer Pro User Guide.
Regulatory Compliance
FCC/Industry Canada
• Controller
• System Remote Control SR-150
• An AV device to be controlled
IMPORTANT! Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
4
Select the Connections view.
5
On the Network tab, ensure the Controller and the System Remote Control
are both network identified (have a network address).
IMPORTANT! Tous les changements ou modifications pas expressément
approuvés par la partie responsable de la conformité ont pu vider
l’autorité de l’utilisateur pour actionner cet équipement.
6
Program the programmable buttons (Red, Green, Yellow, Blue, *, or #) either
based on the selected AV device or the selected room.
FCC ID: R33C4SR150Z/Canadian IC : 7848A-C4SR150Z
This device complies with Part 15 of the FCC Rules Sub-Part B and C and also
with Canada ICES-003 and RSS-Gen. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation of this device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
™
System Remote
Control SR-150
Setup Guide
Batterien.
• Versuchen Sie nicht, eine Batterie neuzuladen, es sei denn die Batterie
ist spezifisch gekennzeichnetes „nachladbares.“
• Entledigen Sie nie sich Batterien in einem Feuer.
Configure the Remote Control
1
Start Composer and connect to a Director.
2
In the System Design view, (selected by default), select the room where the
System Remote Control will reside.
3
In the My Drivers tab, locate the SR-150 under the User Interface section.
Use and Features
Control4 System Remote Control SR-150 (Model C4-SR150B-Z-B) is intended for
use in a Control4® system using OS 1.8.2 and later. This System Remote Control can
be used to:
• Navigate system menus and access media databases on a television or
monitor
• Control system devices
The properties include:
• Keypad Brightness—Set the light level (brightness) of the keypad backlight.
Choose a percentage from 0 (Off) to 100 (full brightness).
• Sleep Mode—Set how long the System Remote Control stays awake after
no activity. The default setting is 15 seconds, but can be extended up to 60
seconds or can be reduced down to 0 to conserve battery life. Select wake on
movement to wake the remote when picked up.
• Batteries—Displays the current strength of the batteries.
• Network:
MAC—Displays the System Remote Control’s own MAC address.
This System Remote Control goes beyond a typical “universal” remote that simply
learns IR codes from TVs, VCRs, CD players, and DVD players. This device features:
•
•
•
•
•
•
•
Bi-directional communication with system components
ZigBee wireless mesh networking
Full access to system components
Back-lighting on keys for ease of use in dark rooms
Quick-access buttons to select recently used audio and video devices
Programmable buttons
Standard control features for: Digital Satellite Systems (DSS), cable boxes, TV
tuners, Digital Video Recorders (DVR), DVD changers/players, CD changers/
players, MP3 players, VCRs, or TVs.
• Powered by four (4) AAA batteries (included)
Install and Maintain the Batteries
4
Double-click SR-150 to add the device to the project tree.
5
Identify the SR-150:
•
•
•
•
In the Connections view, click the Network tab.
Select System Remote Control SR-150 in the center pane.
Click Identify (or right-click and choose Identify).
When prompted to do so, press the red 4 button four (4) times to have the
device identify to the Control4 system.
• Check ZigBee Channel—To determine the current ZigBee channel: Press
Room Off, #,*,7,4,7 then count the blinks of Room Off. The number of blinks
corresponds with the channel number.
• Reset to Factory Defaults—To reset all settings to the factory defaults and
leave the ZigBee network: Press Room Off, #,*,1,3,4,1,3.
Program the Programmable Buttons
Battery Use and Care Tips
On the System Remote Control SR-150, you can program six (6) soft buttons (Red,
Green, Yellow, Blue, *, and #) to perform programmed activities. These buttons can
be programmed to execute any of the AV device’s macros or IR codes. Program
these options using the AV device Properties page.
• Keep the battery contacts and compartment clean.
• Remove the batteries from the product if it is not going to be used for
several months.
• Extreme temperatures reduce battery performance. Avoid putting the SR-150
in very warm places.
Battery Replacement and Safety Rules
CAUTION! To prevent a battery short, leakage or rupture:
• Use typical AAA Alkaline batteries only.
• Do not mix battery types, such as Alkaline and rechargeable
NiMH batteries.
• Do not attempt to recharge a battery unless the battery is specifically
marked “rechargeable.”
• Never dispose of batteries in a fire.
ATTENTION! Pour empêcher court-circuiter, fuite ou rupture de batterie:
Utilisez les accumulateurs alcalins typiques d’AAA seulement.
• Ne mélangez pas les types de batterie, tels que les batteries alkalines
et rechargeables de NiMH.
• N’essayez pas de recharger une batterie à moins que la batterie soit
spécifiquement marqué « rechargeable ».
• Ne vous débarassez jamais des batteries dans un feu.
• Ne vous débarassez jamais des batteries dans un feu.
VORSICHT! Das Batteriekurzschluß, -durchsickern oder -abbruch
verhindern:
• Benutzen Sie AAA alkalische Batterien nur im Schalter.
• Mischen Sie nicht Batteriearten, wie alkalische und nachladbare NiMH
Note: To complete the identification process, the System Remote Control
must be on the same ZigBee channel as the Controller; the Controller must
have Zserver enabled. If you need to change the ZigBee channel on the
System Remote Control, see Step 7.
• When the MAC address appears in the window, click Close.
6
View or change the System Remote Control properties as needed in
Composer. In the System Design view’s project tree, select the System
Remote Control SR-150 object to display the device’s properties.
• Select the System Design view.
• Select an AV device to display the device’s Properties page.
• On the device’s Properties page, choose Code or Macro for the button you
want to program, and then choose a code or macro from the drop-down list,
edit the Help text as needed, and then choose Set.
NOTE: Help text describes custom programming to end-users under the
House option in any of the Navigators.
Firmware Version—Displays the current firmware version.
• Watch/Listen Button Behavior—Select to start the most recently-used
device.
7
Change System Remote Control settings as needed at the SR-150 remote by
using the applicable button-press sequence:
Install the Batteries
Install the four (4) AAA batteries (included) into the back of the SR-150. Insert
them according to the diagram provided in the battery compartment (with the +
and - terminals aligned correctly).
Based on AV device (pictured):
1
Start Composer and connect to a Director.
2
Ensure the System Design view is selected.
3
Ensure that you have the following devices in your project:
For example:
(1) In System Design view, select Disc Changer.
(2) Under Red button, choose Code.
(3) From the drop-down list, choose Subtitle.
(4) Choose the Set button to create a Subtitle button.
Based on room:
Select the Programming view.
Select a room in the Device Events pane.
Select the Commands radio button in the [Room] Events pane.
Use the drop-down menu to select a command or button (such as “Blue
Button”).
• Build the script using items from the Actions pane to program the actions
desired in the selected room when you select the command or button.
•
•
•
•
For more information about programming, see the Composer Pro User Guide.
Regulatory Compliance
FCC/Industry Canada
• Controller
• System Remote Control SR-150
• An AV device to be controlled
IMPORTANT! Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
4
Select the Connections view.
5
On the Network tab, ensure the Controller and the System Remote Control
are both network identified (have a network address).
IMPORTANT! Tous les changements ou modifications pas expressément
approuvés par la partie responsable de la conformité ont pu vider
l’autorité de l’utilisateur pour actionner cet équipement.
6
Program the programmable buttons (Red, Green, Yellow, Blue, *, or #) either
based on the selected AV device or the selected room.
FCC ID: R33C4SR150Z/Canadian IC : 7848A-C4SR150Z
This device complies with Part 15 of the FCC Rules Sub-Part B and C and also
with Canada ICES-003 and RSS-Gen. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation of this device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
™
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de
l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
This equipment has been tested and found to comply with the limits for a Class
B and C digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Australian/New Zealand
This product has been tested to the requirements of, and shown to be in
compliance with, the following requisite standard:
• AS/NZS 4268:2003 +A1:2005 & A2:2006
Limited 2-Year Warranty
For complete warranty information, including details on consumer legal rights as
well as warranty exclusions, visit www.control4.com/warranty.
Recycling
For information on recycling, please go to www.control4.com/recycling.
China RoHS
™
About this Document
Part Number: 200-0070 Rev C 3/28/2011
control4.com | 888.400.4070
©2011 Control4. All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks of
Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners.
™
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de
l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
This equipment has been tested and found to comply with the limits for a Class
B and C digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Australian/New Zealand
This product has been tested to the requirements of, and shown to be in
compliance with, the following requisite standard:
• AS/NZS 4268:2003 +A1:2005 & A2:2006
Limited 2-Year Warranty
For complete warranty information, including details on consumer legal rights as
well as warranty exclusions, visit www.control4.com/warranty.
Recycling
For information on recycling, please go to www.control4.com/recycling.
China RoHS
™
About this Document
Part Number: 200-0070 Rev C 3/28/2011
control4.com | 888.400.4070
©2011 Control4. All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks of
Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising