Intel Core C2D T5270
Intel® Core™2 Duo Mobile
Processor, Intel® Core™2 Solo
Mobile Processor and Intel® Core™2
Extreme Mobile Processor on 45-nm
Process
Datasheet
For platforms based on Mobile Intel® 4 Series Express Chipset Family
March 2009
Document Number: 320120-004
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR
OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS
OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING
TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,
MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS OTHERWISE AGREED IN WRITING BY INTEL, THE INTEL PRODUCTS ARE NOT DESIGNED NOR INTENDED FOR ANY APPLICATION IN WHICH THE
FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL INJURY OR DEATH MAY OCCUR.
Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics
of any features or instructions marked “reserved” or “undefined.” Intel reserves these for future definition and shall have no responsibility whatsoever for
conflicts or incompatibilities arising from future changes to them. The information here is subject to change without notice. Do not finalize a design with
this information.
The products described in this document may contain design defects or errors known as errata which may cause the product to deviate from published
specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Φ 64-bit computing on Intel architecture requires a computer system with a processor, chipset, BIOS, operating system, device drivers and applications
enabled for IntelÆ 64 architecture. Performance will vary depending on your hardware and software configurations. Consult with your system vendor for
more information.
Enhanced Intel SpeedStep® Technology for specified units of this processor are available. See the Processor Spec Finder at http://
processorfinder.intel.com or contact your Intel representative for more information.
Enabling Execute Disable Bit functionality requires a PC with a processor with Execute Disable Bit capability and a supporting operating system. Check
with your PC manufacturer on whether your system delivers Execute Disable Bit functionality.
Φ
Intel® Virtualization Technology requires a computer system with an enabled Intel® processor, BIOS, virtual machine monitor (VMM) and, for some
uses, certain platform software enabled for it. Functionality, performance or other benefits will vary depending on hardware and software configurations
and may require a BIOS update. Software applications may not be compatible with all operating systems. Please check with your application vendor.
Intel, Pentium, Centrino, Intel Core Duo, Intel SpeedStep, MMX and the Intel logo are trademarks of Intel Corporation in the U.S. and other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 2008-2009, Intel Corporation. All rights reserved.
2
Datasheet
Contents
1
Introduction .............................................................................................................. 7
1.1
Terminology ....................................................................................................... 8
1.2
References ......................................................................................................... 9
2
Low Power Features ................................................................................................ 11
2.1
Clock Control and Low-Power States .................................................................... 11
2.1.1 Core Low-Power State Descriptions........................................................... 13
2.1.1.1 Core C0 State........................................................................... 13
2.1.1.2 Core C1/AutoHALT Powerdown State ........................................... 13
2.1.1.3 Core C1/MWAIT Powerdown State ............................................... 14
2.1.1.4 Core C2 State........................................................................... 14
2.1.1.5 Core C3 State........................................................................... 14
2.1.1.6 Core C4 State........................................................................... 14
2.1.1.7 Core Deep Power Down Technology (Code Name C6) State ............ 15
2.1.2 Package Low-power State Descriptions...................................................... 15
2.1.2.1 Normal State............................................................................ 15
2.1.2.2 Stop-Grant State ...................................................................... 15
2.1.2.3 Stop-Grant Snoop State............................................................. 16
2.1.2.4 Sleep State .............................................................................. 16
2.1.2.5 Deep Sleep State ...................................................................... 16
2.1.2.6 Deeper Sleep State ................................................................... 17
2.2
Enhanced Intel SpeedStep® Technology .............................................................. 19
2.3
Extended Low-Power States................................................................................ 20
2.4
FSB Low Power Enhancements ............................................................................ 21
2.4.1 Dynamic FSB Frequency Switching ........................................................... 21
2.4.2 Enhanced Intel® Dynamic Acceleration Technology .................................... 22
2.5
VID-x .............................................................................................................. 23
2.6
Processor Power Status Indicator (PSI-2) Signal .................................................... 23
3
Electrical Specifications ........................................................................................... 25
3.1
Power and Ground Pins ...................................................................................... 25
3.2
Decoupling Guidelines ........................................................................................ 25
3.2.1 VCC Decoupling...................................................................................... 25
3.2.2 FSB AGTL+ Decoupling ........................................................................... 25
3.2.3 FSB Clock (BCLK[1:0]) and Processor Clocking ........................................... 25
3.3
Voltage Identification and Power Sequencing ........................................................ 26
3.4
Catastrophic Thermal Protection .......................................................................... 29
3.5
Reserved and Unused Pins.................................................................................. 29
3.6
FSB Frequency Select Signals (BSEL[2:0])............................................................ 29
3.7
FSB Signal Groups............................................................................................. 30
3.8
CMOS Signals ................................................................................................... 31
3.9
Maximum Ratings.............................................................................................. 31
3.10 Processor DC Specifications ................................................................................ 32
4
Package Mechanical Specifications and Pin Information .......................................... 51
4.1
Package Mechanical Specifications ....................................................................... 51
4.2
Processor Pinout and Pin List .............................................................................. 59
4.3
Alphabetical Signals Reference ............................................................................ 93
5
Thermal Specifications and Design Considerations ................................................ 101
5.1
Monitoring Die Temperature ............................................................................. 108
5.1.1 Thermal Diode ..................................................................................... 108
5.1.2 Intel® Thermal Monitor......................................................................... 109
Datasheet
3
5.2
5.3
5.1.3 Digital Thermal Sensor .......................................................................... 111
Out of Specification Detection............................................................................ 112
PROCHOT# Signal Pin ...................................................................................... 112
Figures
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Core Low-Power States .............................................................................................12
Package Low-Power States ........................................................................................13
Dynamic FSB Frequency Switching Protocol..................................................................22
Active VCC and ICC Loadline for Standard Voltage, Low-Power SV (25 W) and Dual-Core,
Extreme Edition Processors ........................................................................................43
Deeper Sleep VCC and ICC Loadline for Standard-Voltage, Low-Power SV (25 W) and DualCore Extreme Edition Processors ................................................................................44
Deeper Sleep VCC and ICC Loadline for Low-Power Standard-Voltage Processors ..............45
Active VCC and ICC Loadline for Low-Voltage, Ultra-Low-Voltage and Power Optimized
Performance Processor ..............................................................................................46
Deeper Sleep VCC and ICC Loadline for Low-Voltage, Ultra-Low-Voltage and Power Optimized
Performance Processor ..............................................................................................47
6-MB and 3-MB on 6-MB Die Micro-FCPGA Package Drawing (Sheet 1 of 2) ......................52
3-MB die Micro-FCPGA Processor Package Drawing (Sheet 1 of 2) ...................................53
3-MB Die Micro-FCPGA Processor Package Drawing (Sheet 2 of 2)...................................54
3-MB Die Micro-FCBGA Processor Package Drawing (Sheet 1 of 2) ..................................55
3-MB Die Micro-FCBGA Processor Package Drawing (Sheet 2 of 2) ..................................56
Intel Core 2 Duo Mobile Processor (POP and LV) Die Micro-FCBGA Processor Package
Drawing ..................................................................................................................57
Intel Core 2 Duo Mobile Processor (ULV SC and ULV DC) Die Micro-FCBGA Processor Package
Drawing ..................................................................................................................58
Processor Pinout (Top Package View, Left Side) ............................................................59
Processor Pinout (Top Package View, Right Side) ..........................................................60
Intel Core 2 Duo Mobile Processor in SFF Package Top View Upper Left Side .....................80
Intel Core 2 Duo Mobile Processor in SFF Package Top View Upper Right Side ...................81
Intel Core 2 Duo Mobile Processor in SFF Package Top View Lower Left Side .....................82
Intel Core 2 Duo Mobile Processor in SFF Package Top View Lower Right Side ...................83
Tables
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
4
Coordination of Core Low-Power States at the Package Level..........................................13
Voltage Identification Definition ..................................................................................26
BSEL[2:0] Encoding for BCLK Frequency......................................................................29
FSB Pin Groups ........................................................................................................30
Processor Absolute Maximum Ratings..........................................................................31
Voltage and Current Specifications for the Dual-Core, Extreme Edition Processors .............32
Voltage and Current Specifications for the Dual-Core, Standard-Voltage Processors ...........34
Voltage and Current Specifications for the Dual-Core, Low-Power Standard-Voltage Processors
(25 W) in Standard Package ......................................................................................35
Voltage and Current Specifications for the Dual-Core, Power Optimized Performance (25 W)
SFF Processors.........................................................................................................37
Voltage and Current Specifications for the Dual-Core, Low-Voltage SFF Processor .............38
Voltage and Current Specifications for the Dual-Core, Ultra-Low-Voltage SFF Processor .....40
Voltage and Current Specifications for the Ultra-Low-Voltage, Single-Core
(5.5 W) SFF Processor...............................................................................................41
AGTL+ Signal Group DC Specifications ........................................................................48
CMOS Signal Group DC Specifications..........................................................................49
Open Drain Signal Group DC Specifications ..................................................................49
Datasheet
16
17
18
19
20
21
22
23
24
25
26
27
28
Pin Name Listing ...................................................................................................... 61
Pin # Listing............................................................................................................ 72
Intel Core 2 Duo Mobile Processor in SFF Package Listing by Ball Name ........................... 84
Signal Description .................................................................................................... 93
Power Specifications for the Dual-Core Extreme Edition Processor................................. 101
Power Specifications for the Dual-Core Standard Voltage Processor............................... 102
Power Specifications for the Dual-Core Low Power Standard Voltage Processors (25 W) in
Standard Package .................................................................................................. 103
Power Specifications for the Dual-Core Power Optimized Performance (25 W) SFF
Processors ............................................................................................................ 104
Power Specifications fro the Dual-Core Low Voltage (LV) SFF Processors ....................... 105
Power Specifications for the Dual-Core Ultra-Low-Voltage (ULV) Processors ................... 106
Power Specifications for the Single-Core Ultra-Low-Voltage (5.5 W) SFF Processors ........ 107
Thermal Diode Interface ......................................................................................... 108
Thermal Diode Parameters Using Transistor Model...................................................... 109
Datasheet
5
Revision History
Document
Number
Revision
Number
320120
-001
Description
Initial Release
Date
July 2008
• Chapter Update
— Chapter 1: Added introduction to the Intel Core 2 Duo
Processor in SFF Package
— Section 4.1: Added the package coplanarity information for
the processors in SFF Package
• Figure Update
320120
-002
— Added Figure
— Added Figure
— Added Figure
— Added Figure
— Added Figure
• Table Update
—
—
—
—
—
—
—
—
—
320120
-003
7
8
14
15
18 through Figure 21
August 2008
Added Table 9
Added Table 10
Added Table 11
Added Table 12
Updated Table 16: Added Intel Core 2 Duo SFF Package
Processor Ball listing by Pin name
Added Table 18
Added Table 23
Added Table 24
Added Table 25
• Added information for Intel Core 2 Duo T9800, T9550, P9600,
P8700
January 2009
• Added information for Intel Core 2 Duo processor skus below:
320120
-004
—
—
—
—
—
Updated Table 7 and 21 with T9900
Updated Table 9 and 23 with SP9600
Updated Table 10 and 24 with SL9600
Updataed Table 11 and 25 with SU9600
Updated Table 12 and 26 with SU3500
March 2009
§
6
Datasheet
Introduction
1
Introduction
The Intel® Core™2 Duo mobile processor, Intel® Core™2 Duo mobile processor lowvoltage (LV), ultra low-voltage (ULV) in small form factor (SFF) package and Intel®
Core™2 Extreme mobile are high-performance, low-power mobile processor based on
the Intel Core microarchitecture for Intel® Centrino® 2 processor technology.
This document contains electrical, mechanical and thermal specifications for the
following processors:
• The Intel Core 2 Duo processors and Intel Core 2 Extreme processors support the
Mobile Intel® 4 Series Express Chipset and Intel® ICH9M I/O controller.
— Dual-core extreme edition (DC-XE)
— Standard voltage (SV)
— 25-W processor in standard package (Power Optimized Performance-POP)
• The Intel Core 2 Duo processor in SFF package supports the Mobile Intel® GS45
Express Chipset and Intel® ICH9M SFF I/O controller.
This document contains electrical, mechanical and thermal specifications for:
— Power Optimized Performance (POP) in SFF package
— Low-voltage (LV) Processor in SFF package
— Ultra-low voltage (ULV) dual-core (DC) and single-core (SC) Processors in SFF
package
Notes:
In this document
1. Intel Core 2 Duo processor, and the Intel Core 2 Extreme processor are referred to
as the processor
2. Intel Core 2 Duo LV/ULV/POP processors are referred to as SFF processor
3. Mobile Intel 4 Series Express Chipset is referred as the GMCH.
Key features include:
• Dual-core processor for mobile with enhanced performance
• Supports Intel architecture with Intel® Wide Dynamic Execution
• Supports L1 cache-to-cache (C2C) transfer
• On-die, primary 32-KB instruction cache and 32-KB, write-back data cache in each
core
• The processor in DC-XE, standard voltage (SV) and LV have an on-die, up to 6-MB
second-level, shared cache with Advanced Transfer Cache architecture
• The processor in ULV single-core and dual-core have an on-die, up to 3-MB
second-level, shared cache with Advanced Transfer Cache architecture
• Streaming SIMD extensions 2 (SSE2), streaming SIMD extensions 3 (SSE3),
supplemental streaming SIMD extensions 3 (SSSE3) and SSE4.1 instruction sets
• The processor in DC-XE, SV and LV are offered at 1066-MHz, source-synchronous
front side bus (FSB)
• The processor in ULV are offered at 800-MHz, source-synchronous FSB
• Advanced power management features including Enhanced Intel SpeedStep®
Technology and dynamic FSB frequency switching
Datasheet
7
Introduction
• Digital thermal sensor (DTS)
• Intel® 64 architecture
• Supports enhanced Intel® Virtualization Technology
• Enhanced Intel® Dynamic Acceleration Technology and Enhanced Multi-Threaded
Thermal Management (EMTTM)
• Supports PSI2 functionality
• SV processor offered in Micro-FCPGA and Micro-FCBGA packaging technologies
• Processor in POP, LV and ULV are offered in Micro-FCBGA packaging technologies
only
• Execute Disable Bit support for enhanced security
• Intel® Deep Power Down low-power state with P_LVL6 I/O support
• Support for Intel® Trusted Execution Technology
• Half ratio support (N/2) for core to bus ratio
1.1
Terminology
Term
8
Definition
#
A “#” symbol after a signal name refers to an active low signal, indicating a
signal is in the active state when driven to a low level. For example, when
RESET# is low, a reset has been requested. Conversely, when NMI is high,
a nonmaskable interrupt has occurred. In the case of signals where the
name does not imply an active state but describes part of a binary
sequence (such as address or data), the “#” symbol implies that the signal
is inverted. For example, D[3:0] = “HLHL” refers to a hex ‘A’, and D[3:0]#
= “LHLH” also refers to a hex “A” (H= High logic level, L= Low logic level).
Front Side Bus
(FSB)
Refers to the interface between the processor and system core logic (also
known as the chipset components).
AGTL+
Advanced Gunning Transceiver Logic. Used to refer to Assisted GTL+
signaling technology on some Intel processors.
Storage
Conditions
Refers to a non-operational state. The processor may be installed in a
platform, in a tray, or loose. Processors may be sealed in packaging or
exposed to free air. Under these conditions, processor landings should not
be connected to any supply voltages, have any I/Os biased or receive any
clocks. Upon exposure to “free air” (i.e., unsealed packaging or a device
removed from packaging material) the processor must be handled in
accordance with moisture sensitivity labeling (MSL) as indicated on the
packaging material.
Enhanced Intel
SpeedStep®
Technology
Technology that provides power management capabilities to laptops.
Processor Core
Processor core die with integrated L1 and L2 cache. All AC timing and signal
integrity specifications are at the pads of the processor core.
Datasheet
Introduction
Term
1.2
Definition
Execute Disable
Bit
The Execute Disable bit allows memory to be marked as executable or nonexecutable, when combined with a supporting operating system. If code
attempts to run in non-executable memory the processor raises an error to
the operating system. This feature can prevent some classes of viruses or
worms that exploit buffer overrun vulnerabilities and can thus help improve
the overall security of the system. See the Intel® 64 and IA-32
Architectures Software Developer's Manuals for more detailed information.
Intel® 64
Technology
64-bit memory extensions to the IA-32 architecture.
Intel®
Virtualization
Technology
Processor virtualization that, when used in conjunction with Virtual Machine
Monitor software, enables multiple, robust independent software
environments inside a single platform.
Half ratio support
(N/2) for Core to
Bus ratio
Intel Core 2 Duo processors and Intel Core 2 Extreme processors support
the N/2 feature that allows having fractional core-to-bus ratios. This feature
provides the flexibility of having more frequency options and being able to
have products with smaller frequency steps.
TDP
Thermal Design Power.
VCC
The processor core power supply.
VSS
The processor ground.
LV
Low-voltage
ULV
Ultra-Low-Voltage
DC-XE
Dual-core Extreme Edition
References
Material and concepts available in the following documents may be beneficial when
reading this document.
Document
Document
Number
Intel® Core™2 Duo Mobile Processor, Intel® Core™2 Solo Mobile
Processor, Intel® Core™2 Extreme Processor on 45-nm Technology
Specification Update
320121
Mobile Intel® 4 Series Express Chipset Family Datasheet
320122
Mobile Intel® 4 Series Express Chipset Family Specification Update
320123
Intel® I/O Controller Hub 9 (ICH9)/ I/O Controller Hub 9M (ICH9M)
Datasheet
316972
Intel® I/O Controller Hub 9 (ICH9)/ I/O Controller Hub 9M (ICH9M)
Specification Update
316973
Intel® 64 and IA-32 Architectures Software Developer's Manuals
Volume 1: Basic Architecture
253665
Volume 2A: Instruction Set Reference, A-M
253666
Datasheet
9
Introduction
Document
Number
Document
Volume 2B: Instruction Set Reference, N-Z
253667
Volume 3A: System Programming Guide
253668
Volume 3B: System Programming Guide
253669
NOTE: Contact your Intel representative for the latest revision of this document.
§
10
Datasheet
Low Power Features
2
Low Power Features
2.1
Clock Control and Low-Power States
The processor supports low-power states both at the individual core level and the
package level for optimal power management.
A core may independently enter the C1/AutoHALT, C1/MWAIT, C2, C3, C4, Intel®
Enhanced Deeper Sleep and Intel® Deep Power Down Technology low-power states.
When both cores coincide in a common core low-power state, the central power
management logic ensures the entire processor enters the respective package lowpower state by initiating a P_LVLx (P_LVL2, P_LVL3, P_LVL4, P_LVL5,P_LVL6) I/O read
to the GMCH.
The processor implements two software interfaces for requesting low-power states:
MWAIT instruction extensions with sub-state hints and P_LVLx reads to the ACPI P_BLK
register block mapped in the processor’s I/O address space. The P_LVLx I/O reads are
converted to equivalent MWAIT C-state requests inside the processor and do not
directly result in I/O reads on the processor FSB. The P_LVLx I/O Monitor address does
not need to be set up before using the P_LVLx I/O read interface. The sub-state hints
used for each P_LVLx read can be configured through the IA32_MISC_ENABLES model
specific register (MSR).
If a core encounters a GMCH break event while STPCLK# is asserted, it asserts the
PBE# output signal. Assertion of PBE# when STPCLK# is asserted indicates to system
logic that individual cores should return to the C0 state and the processor should return
to the Normal state.
Figure 1 shows the core low-power states and Figure 2 shows the package low-power
states for the processor. Table 1 maps the core low-power states to package low-power
states.
Datasheet
11
Low Power Features
Figure 1.
Core Low-Power States
Stop
Grant
STPCLK#
asserted
STPCLK#
deasserted
C1/MWAIT
STPCLK#
deasserted
STPCLK#
STPCLK# asserted
deasserted
STPCLK#
asserted
Core state
break
HLT instruction
MWAIT(C1)
Halt break
C0
Core State
break
P_LVL4 or
P_LVL5/P_LVL6ø
MWAIT(C4/C6)
C4† ‡/C6
C1/Auto
Halt
P_LVL2 or
MWAIT(C2)
Core state
break
P_LVL3 or
Core MWAIT(C3)
state
break
C2†
C3†
halt break = A20M# transition, INIT#, INTR, NMI, PREQ#, RESET#, SMI#, or APIC interrupt
core state break = (halt break OR Monitor event) AND STPCLK# high (not asserted)
† — STPCLK# assertion and de-assertion have no effect if a core is in C2, C3, or C4.
‡ — Core C4 state supports the package level Deep C4 sub-state.
Ø — P_LVL5/P_LVL6 read is issued once the L2 cache is reduced to zero.
12
Datasheet
Low Power Features
Figure 2.
Package Low-Power States
SLP# asserted
STPCLK# asserted
DPSLP# asserted
Stop
Grant
Normal
Sleep
STPCLK# deasserted
DPRSTP# asserted
Deep
Sleep
SLP# deasserted
DPSLP# deasserted
Deeper
Sleep†
DPRSTP# deasserted
Snoop Snoop
serviced occurs
Stop Grant
Snoop
† — Deeper Sleep includes the Deeper Sleep state, Deep C4 sub-state, and C6
Table 1.
Coordination of Core Low-Power States at the Package Level
Package State
Core1 State
Core0 State
C0
C11
C2
C3
C4/Deep Power Down
Technology State
(Code Named C6 State)
C0
Normal
Normal
Normal
Normal
Normal
C11
Normal
Normal
Normal
Normal
Normal
C2
Normal
Normal
Stop-Grant
Stop-Grant
Stop-Grant
C3
Normal
Normal
Stop-Grant
Deep Sleep
Deep Sleep
Deep Sleep
Deeper Sleep /Intel®
Enhanced Deeper Sleep/
Intel® Deep Power Down
C4/Deep Power
Down Technology
Normal
Normal
Stop-Grant
NOTE:
1.
AutoHALT or MWAIT/C1.
2.1.1
Core Low-Power State Descriptions
2.1.1.1
Core C0 State
This is the normal operating state for cores in the processor.
2.1.1.2
Core C1/AutoHALT Powerdown State
C1/AutoHALT is a low-power state entered when a core executes the HALT instruction.
The processor core will transition to the C0 state upon occurrence of SMI#, INIT#,
LINT[1:0] (NMI, INTR), or FSB interrupt messages. RESET# will cause the processor to
immediately initialize itself.
A System Management Interrupt (SMI) handler will return execution to either Normal
state or the AutoHALT Powerdown state. See the Intel® 64 and IA-32 Architectures
Software Developer's Manuals, Volume 3A/3B: System Programmer's Guide for more
information.
Datasheet
13
Low Power Features
The system can generate a STPCLK# while the processor is in the AutoHALT
Powerdown state. When the system deasserts the STPCLK# interrupt, the processor
will return execution to the HALT state.
While in AutoHALT Powerdown state, the dual-core processor will process bus snoops
and snoops from the other core. The processor core will enter a snoopable sub-state
(not shown in Figure 1) to process the snoop and then return to the AutoHALT
Powerdown state.
2.1.1.3
Core C1/MWAIT Powerdown State
C1/MWAIT is a low-power state entered when the processor core executes the
MWAIT(C1) instruction. Processor behavior in the MWAIT state is identical to the
AutoHALT state except that Monitor events can cause the processor core to return to
the C0 state. See the Intel® 64 and IA-32 Architectures Software Developer's Manuals,
Volume 2A: Instruction Set Reference, A-M and Volume 2B: Instruction Set Reference,
N-Z, for more information.
2.1.1.4
Core C2 State
Individual cores of the dual-core processor can enter the C2 state by initiating a P_LVL2
I/O read to the P_BLK or an MWAIT(C2) instruction, but the processor will not issue a
Stop-Grant Acknowledge special bus cycle unless the STPCLK# pin is also asserted.
While in the C2 state, the dual-core processor will process bus snoops and snoops from
the other core. The processor core will enter a snoopable sub-state (not shown in
Figure 1) to process the snoop and then return to the C2 state.
2.1.1.5
Core C3 State
Individual cores of the dual-core processor can enter the C3 state by initiating a P_LVL3
I/O read to the P_BLK or an MWAIT(C3) instruction. Before entering C3, the processor
core flushes the contents of its L1 caches into the processor’s L2 cache. Except for the
caches, the processor core maintains all its architectural states in the C3 state. The
Monitor remains armed if it is configured. All of the clocks in the processor core are
stopped in the C3 state.
Because the core’s caches are flushed the processor keeps the core in the C3 state
when the processor detects a snoop on the FSB or when the other core of the dual-core
processor accesses cacheable memory. The processor core will transition to the C0
state upon occurrence of a Monitor event, SMI#, INIT#, LINT[1:0] (NMI, INTR), or FSB
interrupt message. RESET# will cause the processor core to immediately initialize itself.
2.1.1.6
Core C4 State
Individual cores of the dual-core processor can enter the C4 state by initiating a P_LVL4
or P_LVL5 I/O read to the P_BLK or an MWAIT(C4) instruction. The processor core
behavior in the C4 state is nearly identical to the behavior in the C3 state. The only
difference is that if both processor cores are in C4, the central power management logic
will request that the entire processor enter the Deeper Sleep package low-power state
(see Section 2.1.2.6).
To enable the package-level Intel Enhanced Deeper Sleep state, Dynamic Cache Sizing
and Intel Enhanced Deeper Sleep state fields must be configured in the
PMG_CST_CONFIG_CONTROL MSR. Refer to Section 2.1.2.6 for further details on Intel
Enhanced Deeper Sleep state.
14
Datasheet
Low Power Features
2.1.1.7
Core Deep Power Down Technology (Code Name C6) State
Deep Power Down Technology state is a new, power-saving state which is being
implemented on the processor. In Deep Power Down Technology the processor saves its
entire architectural state onto an on-die SRAM hence allowing it to lower its main core
voltage to any value, even as low as 0-V.
When the core enters Deep Power Down Technology state, it saves the processor state
that is relevant to the processor context in an on-die SRAM that resides on a separate
power plane VCCP (I/O power supply). This allows the main core Vcc to be lowered to
any arbitrary voltage including 0-V. The on-die storage for saving the processor state is
implemented as a per-core SRAM.
2.1.2
Package Low-power State Descriptions
2.1.2.1
Normal State
This is the normal operating state for the processor. The processor remains in the
Normal state when at least one of its cores is in the C0, C1/AutoHALT, or C1/MWAIT
state.
2.1.2.2
Stop-Grant State
When the STPCLK# pin is asserted, each core of the dual-core processor enters the
Stop-Grant state within 20 bus clocks after the response phase of the processor-issued
Stop-Grant Acknowledge special bus cycle. Processor cores that are already in the C2,
C3, or C4 state remain in their current low-power state. When the STPCLK# pin is
deasserted, each core returns to its previous core low-power state.
Since the AGTL+ signal pins receive power from the FSB, these pins should not be
driven (allowing the level to return to VCCP) for minimum power drawn by the
termination resistors in this state. In addition, all other input pins on the FSB should be
driven to the inactive state.
RESET# causes the processor to immediately initialize itself, but the processor will stay
in Stop-Grant state. When RESET# is asserted by the system, the STPCLK#, SLP#,
DPSLP#, and DPRSTP# pins must be deasserted prior to RESET# deassertion as per AC
Specification T45. When re-entering the Stop-Grant state from the Sleep state,
STPCLK# should be deasserted after the deassertion of SLP# as per AC Specification
T75.
While in Stop-Grant state, the processor will service snoops and latch interrupts
delivered on the FSB. The processor will latch SMI#, INIT# and LINT[1:0] interrupts
and will service only one of each upon return to the Normal state.
The PBE# signal may be driven when the processor is in Stop-Grant state. PBE# will be
asserted if there is any pending interrupt or Monitor event latched within the processor.
Pending interrupts that are blocked by the EFLAGS.IF bit being clear will still cause
assertion of PBE#. Assertion of PBE# indicates to system logic that the entire processor
should return to the Normal state.
A transition to the Stop-Grant Snoop state occurs when the processor detects a snoop
on the FSB (see Section 2.1.2.3). A transition to the Sleep state (see Section 2.1.2.4)
occurs with the assertion of the SLP# signal.
Datasheet
15
Low Power Features
2.1.2.3
Stop-Grant Snoop State
The processor responds to snoop or interrupt transactions on the FSB while in StopGrant state by entering the Stop-Grant Snoop state. The processor will stay in this
state until the snoop on the FSB has been serviced (whether by the processor or
another agent on the FSB) or the interrupt has been latched. The processor returns to
the Stop-Grant state once the snoop has been serviced or the interrupt has been
latched.
2.1.2.4
Sleep State
The Sleep state is a low-power state in which the processor maintains its context,
maintains the phase-locked loop (PLL), and stops all internal clocks. The Sleep state is
entered through assertion of the SLP# signal while in the Stop-Grant state. The SLP#
pin should only be asserted when the processor is in the Stop-Grant state. SLP#
assertions while the processor is not in the Stop-Grant state is out of specification and
may result in unapproved operation.
In the Sleep state, the processor is incapable of responding to snoop transactions or
latching interrupt signals. No transitions or assertions of signals (with the exception of
SLP#, DPSLP# or RESET#) are allowed on the FSB while the processor is in Sleep
state. Snoop events that occur while in Sleep state or during a transition into or out of
Sleep state will cause unpredictable behavior. Any transition on an input signal before
the processor has returned to the Stop-Grant state will result in unpredictable behavior.
If RESET# is driven active while the processor is in the Sleep state, and held active as
specified in the RESET# pin specification, then the processor will reset itself, ignoring
the transition through the Stop-Grant state. If RESET# is driven active while the
processor is in the Sleep state, the SLP# and STPCLK# signals should be deasserted
immediately after RESET# is asserted to ensure the processor correctly executes the
Reset sequence.
While in the Sleep state, the processor is capable of entering an even lower power
state, the Deep Sleep state, by asserting the DPSLP# pin (See Section 2.1.2.5). While
the processor is in the Sleep state, the SLP# pin must be deasserted if another
asynchronous FSB event needs to occur.
2.1.2.5
Deep Sleep State
The Deep Sleep state is entered through assertion of the DPSLP# pin while in the Sleep
state. BCLK may be stopped during the Deep Sleep state for additional platform-level
power savings. BCLK stop/restart timings on appropriate GMCH-based platforms with
the CK505 clock chip are as follows:
• Deep Sleep entry: the system clock chip may stop/tristate BCLK within 2 BCLKs
of DPSLP# assertion. It is permissible to leave BCLK running during Deep Sleep.
• Deep Sleep exit: the system clock chip must drive BCLK to differential DC levels
within 2-3 ns of DPSLP# deassertion and start toggling BCLK within 10 BCLK
periods.
To re-enter the Sleep state, the DPSLP# pin must be deasserted. BCLK can be restarted after DPSLP# deassertion as described above. A period of 15 microseconds (to
allow for PLL stabilization) must occur before the processor can be considered to be in
the Sleep state. Once in the Sleep state, the SLP# pin must be deasserted to re-enter
the Stop-Grant state.
While in Deep Sleep state, the processor is incapable of responding to snoop
transactions or latching interrupt signals. No transitions of signals are allowed on the
FSB while the processor is in Deep Sleep state. When the processor is in Deep Sleep
16
Datasheet
Low Power Features
state, it will not respond to interrupts or snoop transactions. Any transition on an input
signal before the processor has returned to Stop-Grant state will result in unpredictable
behavior.
2.1.2.6
Deeper Sleep State
The Deeper Sleep state is similar to the Deep Sleep state but further reduces core
voltage levels. One of the potential lower core voltage levels is achieved by entering the
base Deeper Sleep state. The Deeper Sleep state is entered through assertion of the
DPRSTP# pin while in the Deep Sleep state. The following lower core voltage level is
achieved by entering the Intel Enhanced Deeper Sleep state which is a sub-state of
Deeper Sleep state. Intel Enhanced Deeper Sleep state is entered through assertion of
the DPRSTP# pin while in the Deep Sleep only when the L2 cache has been completely
shut down. Refer to Section 2.1.2.6.1 and Section 2.1.2.6.3 for further details on
reducing the L2 cache and entering Intel Enhanced Deeper Sleep state.
In response to entering Deeper Sleep, the processor drives the VID code corresponding
to the Deeper Sleep core voltage on the VID[6:0] pins.
Exit from Deeper Sleep or Intel Enhanced Deeper Sleep state is initiated by DPRSTP#
deassertion when either core requests a core state other than C4 or either core
requests a processor performance state other than the lowest operating point.
2.1.2.6.1
Intel® Enhanced Deeper Sleep State
Intel Enhanced Deeper Sleep state is a sub-state of Deeper Sleep that extends powersaving capabilities by allowing the processor to further reduce core voltage once the L2
cache has been reduced to zero ways and completely shut down. The following events
occur when the processor enters Intel Enhanced Deeper Sleep state:
• The last core entering C4 issues a P_LVL4 or P_LVL5 I/O read or an MWAIT(C4)
instruction and then progressively reduces the L2 cache to zero
• Once the L2 cache has been reduced to zero, the processor triggers a special
chipset sequence to notify the chipset to redirect all FSB traffic, except APIC
messages, to memory. The snoops are replied as misses by the chipset and are
directed to main memory instead of the L2 cache. This allows for higher residency
of the processor’s Intel Enhanced Deeper Sleep state.
• The processor drives the VID code corresponding to the Intel Enhanced Deeper
Sleep state core voltage on the VID[6:0] pins.
2.1.2.6.2
Deep Power Down State Technology (Code Named C6) State
When both cores have entered the CC6 state and the L2 cache has been shrunk down
to zero ways, the processor will enter the Deep Power Down Technology state. To do so
both cores save their architectural states in the on-die SRAM that resides in the VCCP
domain. At this point, the core VCC will be dropped to the lowest core voltage closer to
0-V. The processor is now in an extremely low-power state.
In Intel Deep Power Down Technology state, the processor does not need to be
snooped as all the caches are flushed before entering this state.
Datasheet
17
Low Power Features
2.1.2.6.3
Dynamic Cache Sizing
Dynamic Cache Sizing allows the processor to flush and disable a programmable
number of L2 cache ways upon each Deeper Sleep entry under the following
conditions:
• The second core is already in C4 and Intel Enhanced Deeper Sleep state or Deep
Power Down Technology state (C6) is enabled (as specified in Section 2.1.1.6).
• The C0 timer that tracks continuous residency in the Normal package state has not
expired. This timer is cleared during the first entry into Deeper Sleep to allow
consecutive Deeper Sleep entries to shrink the L2 cache as needed.
• The FSB speed to processor core speed ratio is below the predefined L2 shrink
threshold.
The number of L2 cache ways disabled upon each Deeper Sleep entry is configured in
the BBL_CR_CTL3 MSR. The C0 timer is referenced through the
CLOCK_CORE_CST_CONTROL_STT MSR. The shrink threshold under which the L2
cache size is reduced is configured in the PMG_CST_CONFIG_CONTROL MSR. If the
FSB speed to processor core speed ratio is above the predefined L2 shrink threshold,
then L2 cache expansion will be requested. If the ratio is zero, then the ratio will not be
taken into account for Dynamic Cache Sizing decisions.
Upon STPCLK# deassertion, the first core exiting Intel Enhanced Deeper Sleep state or
Deep Power Down Technology state will expand the L2 cache to two ways and
invalidate previously disabled cache ways. If the L2 cache reduction conditions stated
above still exist when the last core returns to C4 and the package enters Intel
Enhanced Deeper Sleep state or Deep Power Down Technology state (C6), then the L2
will be shrunk to zero again. If a core requests a processor performance state resulting
in a higher ratio than the predefined L2 shrink threshold, the C0 timer expires, or the
second core (not the one currently entering the interrupt routine) requests the C1, C2,
or C3 states, then the whole L2 will be expanded upon the next interrupt event.
In addition, the processor supports Full Shrink on L2 cache. When the MWAIT Deep
Power Down Technology state instruction is executed with a hint=0x2 in ECX[3:0], the
micro code will shrink all the active ways of the L2 cache in one step. This ensures that
the package enters Deep Power Down Technology immediately when both cores are in
CC6 instead of iterating till the cache is reduced to zero. The operating system (OS) is
expected to use this hint when it wants to enter the lowest power state and can
tolerate the longer entry latency.
L2 cache shrink prevention may be enabled as needed on occasion through an
MWAIT(C4) sub-state field. If shrink prevention is enabled, the processor does not
enter Intel Enhanced Deeper Sleep state or Intel Deep Power Down state since the L2
cache remains valid and in full size.
18
Datasheet
Low Power Features
2.2
Enhanced Intel SpeedStep® Technology
The processor features Enhanced Intel SpeedStep Technology. Following are the key
features of Enhanced Intel SpeedStep Technology:
• Multiple voltage and frequency operating points provide optimal performance at the
lowest power.
• Voltage and frequency selection is software-controlled by writing to processor
MSRs:
— If the target frequency is higher than the current frequency, VCC is ramped up
in steps by placing new values on the VID pins, and the PLL then locks to the
new frequency.
— If the target frequency is lower than the current frequency, the PLL locks to the
new frequency and the VCC is changed through the VID pin mechanism.
— Software transitions are accepted at any time. If a previous transition is in
progress, the new transition is deferred until the previous transition completes.
• The processor controls voltage ramp rates internally to ensure glitch-free
transitions.
• Low transition latency and large number of transitions possible per second:
— Processor core (including L2 cache) is unavailable for up to 10 μs during the
frequency transition.
— The bus protocol (BNR# mechanism) is used to block snooping.
• Improved Intel® Thermal Monitor mode:
— When the on-die thermal sensor indicates that the die temperature is too high
the processor can automatically perform a transition to a lower frequency and
voltage specified in a software-programmable MSR.
— The processor waits for a fixed time period. If the die temperature is down to
acceptable levels, an up-transition to the previous frequency and voltage point
occurs.
— An interrupt is generated for the up and down Intel Thermal Monitor transitions
enabling better system-level thermal management.
• Enhanced thermal management features:
— Digital Thermal Sensor and Out of Specification detection.
— Intel Thermal Monitor 1 (TM1) in addition to Intel Thermal Monitor 2 (TM2) in
case of unsuccessful TM2 transition.
— Dual-core thermal management synchronization.
Each core in the dual-core processor implements an independent MSR for controlling
Enhanced Intel SpeedStep Technology, but both cores must operate at the same
frequency and voltage. The processor has performance state coordination logic to
resolve frequency and voltage requests from the two cores into a single frequency and
voltage request for the package as a whole. If both cores request the same frequency
and voltage, then the processor will transition to the requested common frequency and
voltage. If the two cores have different frequency and voltage requests, then the
processor will take the highest of the two frequencies and voltages as the resolved
request and transition to that frequency and voltage.
The processor also supports Dynamic FSB Frequency Switching and Intel Dynamic
Acceleration Technology mode on select SKUs. The operating system can take
advantage of these features and request a lower operating point called SuperLFM (due
to Dynamic FSB Frequency Switching) and a higher operating point Intel Dynamic
Acceleration Technology mode.
Datasheet
19
Low Power Features
2.3
Extended Low-Power States
Extended low-power states (CXE) optimize for power by forcibly reducing the
performance state of the processor when it enters a package low-power state. Instead
of directly transitioning into the package low-power state, the enhanced package lowpower state first reduces the performance state of the processor by performing an
Enhanced Intel SpeedStep Technology transition down to the lowest operating point.
Upon receiving a break event from the package low-power state, control will be
returned to software while an Enhanced Intel SpeedStep Technology transition up to
the initial operating point occurs. The advantage of this feature is that it significantly
reduces leakage while in the Stop-Grant and Deeper Sleep states.
Deep Power Down Technology is always enabled in the extended low power state as
described above.
Note:
Long-term reliability cannot be assured unless all the Extended Low Power States are
enabled.
The processor implements two software interfaces for requesting enhanced package
low-power states: MWAIT instruction extensions with sub-state hints and via BIOS by
configuring IA32_MISC_ENABLES MSR bits to automatically promote package lowpower states to enhanced package low-power states.
Caution:
Extended Stop-Grant and Enhanced Deeper Sleep must be enabled via the
BIOS for the processor to remain within specification. As processor technology
changes, enabling the extended low power states becomes increasingly crucial when
building computer systems. Maintaining the proper BIOS configuration is key to
reliable, long-term system operation. Not complying to this guideline may affect the
long-term reliability of the processor.
Caution:
Enhanced Intel SpeedStep Technology transitions are multistep processes
that require clocked control. These transitions cannot occur when the processor is in
the Sleep or Deep Sleep package low-power states since processor clocks are not
active in these states. Extended Deeper Sleep is an exception to this rule when the
Hard C4E configuration is enabled in the IA32_MISC_ENABLES MSR. This Extended
Deeper Sleep state configuration will lower core voltage to the Deeper Sleep level while
in Deeper Sleep and, upon exit, will automatically transition to the lowest operating
voltage and frequency to reduce snoop service latency. The transition to the lowest
operating point or back to the original software-requested point may not be
instantaneous. Furthermore, upon very frequent transitions between active and idle
states, the transitions may lag behind the idle state entry resulting in the processor
either executing for a longer time at the lowest operating point or running idle at a high
operating point. Observations and analyses show this behavior should not significantly
impact total power savings or performance score while providing power benefits in
most other cases.
20
Datasheet
Low Power Features
2.4
FSB Low Power Enhancements
The processor incorporates FSB low power enhancements:
• Dynamic FSB Power Down
• BPRI# control for address and control input buffers
• Dynamic Bus Parking
• Dynamic On-Die Termination disabling
• Low VCCP (I/O termination voltage)
• Dynamic FSB frequency switching
The processor incorporates the DPWR# signal that controls the data bus input buffers
on the processor. The DPWR# signal disables the buffers when not used and activates
them only when data bus activity occurs, resulting in significant power savings with no
performance impact. BPRI# control also allows the processor address and control input
buffers to be turned off when the BPRI# signal is inactive. Dynamic Bus Parking allows
a reciprocal power reduction in GMCH address and control input buffers when the
processor deasserts its BR0# pin. The On-Die Termination on the processor FSB buffers
is disabled when the signals are driven low, resulting in additional power savings. The
low I/O termination voltage is on a dedicated voltage plane independent of the core
voltage, enabling low I/O switching power at all times.
2.4.1
Dynamic FSB Frequency Switching
Dynamic FSB frequency switching effectively reduces the internal bus clock frequency
in half to further decrease the minimum processor operating frequency from the
Enhanced Intel SpeedStep Technology performance states and achieve the Super Low
Frequency Mode (Super LFM). This feature is supported at FSB frequencies of
1066 MHz, 800 MHz and 667 MHz and does not entail a change in the external bus
signal (BCLK) frequency. Instead, both the processor and GMCH internally lower their
BCLK reference frequency to 50% of the externally visible frequency. Both the
processor and GMCH maintain a virtual BCLK signal (VBCLK) that is aligned to the
external BCLK but at half the frequency. After a downward shift, it would appear
externally as if the bus is running with a 133-MHz base clock in all aspects, except that
the actual external BCLK remains at 266 MHz. See Figure 3 for details. The transition
into Super LFM, a “down-shift,” is done following a handshake between the processor
and GMCH. A similar handshake is used to indicate an “up-shift,” a change back to
normal operating mode. Please ensure this feature is enabled and supported in the
BIOS.
Datasheet
21
Low Power Features
Figure 3.
Dynamic FSB Frequency Switching Protocol
NOTES:
1.
All common clock signals will be active for two BCLKs instead of one (e.g., ADS#, HIT#).
2.
The double-pumped signal strobes will have only one transition per BCLK when active,
instead of two.
3.
The quad-pumped signal strobes will have only two transitions per BCLK when active,
instead of four.
4.
Same setup and hold times apply, but relative to every second rising BCLK.
5.
Following a RESET#, the bus will be in the legacy full-frequency mode.
6.
There will not be a down-shift right after RESET# deassertion.
7.
There is no backing out of a transition into or out of half-frequency mode. Once the
sequence starts it must be completed.
2.4.2
Enhanced Intel® Dynamic Acceleration Technology
The processor supports Intel Dynamic Acceleration Technology mode. The Intel
Dynamic Acceleration Technology feature allows one core of the processor to operate at
a higher frequency point when the other core is inactive and the operating system
requests increased performance. This higher frequency is called the opportunistic
frequency and the maximum rated operating frequency is the ensured frequency.
The processor includes a hysteresis mechanism that improves overall Intel Dynamic
Acceleration Technology performance by decreasing unnecessary transitions of the
cores in and out of Intel Dynamic Acceleration Technology mode. Normally, the
processor would exit Intel Dynamic Acceleration Technology as soon as two cores are
active. This can become an issue if the idle core is frequently awakened for a short
periods (i.e., high timer tick rates). The hysteresis mechanism allows two cores to be
active for a limited time before it transitions out of Intel Dynamic Acceleration
Technology mode.
Intel Dynamic Acceleration Technology mode enabling requires:
• Exposure, via BIOS, of the opportunistic frequency as the highest ACPI P state
• Enhanced Multi-Threaded Thermal Management (EMTTM)
• Intel Dynamic Acceleration Technology mode and EMTTM MSR configuration via
BIOS.
22
Datasheet
Low Power Features
When in Intel Dynamic Acceleration Technology mode, it is possible for both cores to be
active under certain internal conditions. In such a scenario the processor may draw a
Instantaneous current (ICC_CORE_INST) for a short duration of tINST; however, the
average ICC current will be lesser than or equal to ICCDES current specification. Please
refer to the Processor DC Specifications section for more details.
2.5
VID-x
The processor implements the VID-x feature for improved control of core voltage levels
when the processor enters a reduced power consumption state. VID-x applies only
when the processor is in the Intel Dynamic Acceleration Technology performance state
and one or more cores are in low-power state (i.e., CC3/CC4/CC6). VID-x provides the
ability for the processor to request core voltage level reductions greater than one VID
tick. The amount of VID tick reduction is fixed and only occurs while the processor is in
Intel Dynamic Acceleration Technology mode. This improved voltage regulator
efficiency during periods of reduced power consumption allows for leakage current
reduction which results in platform power savings and extended battery life.
When in Intel Dynamic Acceleration Technology mode, it is possible for both cores to be
active under certain internal conditions. In such a scenario the processor may draw a
Instantaneous current (ICC_CORE_INST) for a short duration of tINST; however, the
average ICC current will be lesser than or equal to ICCDES current specification. Please
refer to the Processor DC Specifications section for more details.
2.6
Processor Power Status Indicator (PSI-2) Signal
The processor incorporates the PSI# signal that is asserted when the processor is in a
reduced power consumption state. PSI# can be used to improve intermediate and light
load efficiency of the voltage regulator, resulting in platform power savings and
extended battery life. The algorithm that the processor uses for determining when to
assert PSI# is different from the algorithm used in previous mobile processors. PSI-2
functionality is expanded further to support three processor states:
• Both cores are in idle state
• Only one core active state
• Both cores are in active state
PSI-2 functionality improves overall voltage regulator efficiency over a wide power
range based on the C-state and P-state of the two cores. The combined C-state and Pstate of both cores are used to dynamically predict processor power.
The real-time power prediction is compared against a set of predefined and configured
values of CHH and CHL. CHH is indicative of the active C-state of both the cores and
CHL is indicative that only one core is in active C-state and the other core is in low
power core state. PSI-2# output is asserted upon crossing these thresholds indicating
that the processor requires lower power. The voltage regulator will adapt its power
output accordingly. Additionally the voltage regulator may switch to a single phase and/
or asynchronous mode when the processor is idle and fused leakage limit is less than or
equal to the BIOS threshold value.
§
Datasheet
23
Low Power Features
24
Datasheet
Electrical Specifications
3
Electrical Specifications
3.1
Power and Ground Pins
For clean, on-chip power distribution, the processor will have a large number of VCC
(power) and VSS (ground) inputs. All power pins must be connected to VCC power
planes while all VSS pins must be connected to system ground planes. Use of multiple
power and ground planes is recommended to reduce I*R drop. The processor VCC pins
must be supplied the voltage determined by the VID (Voltage ID) pins.
3.2
Decoupling Guidelines
Due to its large number of transistors and high internal clock speeds, the processor is
capable of generating large average current swings between low and full power states.
This may cause voltages on power planes to sag below their minimum values if bulk
decoupling is not adequate. Larger bulk storage, such as electrolytic capacitors, supply
current during longer lasting changes in current demand by the component, such as
coming out of an idle condition. Similarly, they act as a storage well for current when
entering an idle condition from a running condition. Care must be taken in the board
design to ensure that the voltage provided to the processor remains within the
specifications listed in the tables in Section 3.10. Failure to do so can result in timing
violations or reduced lifetime of the component.
3.2.1
VCC Decoupling
VCC regulator solutions need to provide bulk capacitance with a low Effective Series
Resistance (ESR) and keep a low interconnect resistance from the regulator to the
socket. Bulk decoupling for the large current swings when the part is powering on, or
entering/exiting low-power states, should be provided by the voltage regulator solution
depending on the specific system design.
3.2.2
FSB AGTL+ Decoupling
The processors integrate signal termination on the die as well as incorporate high
frequency decoupling capacitance on the processor package. Decoupling must also be
provided by the system motherboard for proper AGTL+ bus operation.
3.2.3
FSB Clock (BCLK[1:0]) and Processor Clocking
BCLK[1:0] directly controls the FSB interface speed as well as the core frequency of the
processor. As in previous-generation processors, the processor core frequency is a
multiple of the BCLK[1:0] frequency. The processor bus ratio multiplier will be set at its
default ratio at manufacturing. The processor uses a differential clocking
implementation.
Datasheet
25
Electrical Specifications
3.3
Voltage Identification and Power Sequencing
The processor uses seven voltage identification pins,VID[6:0], to support automatic
selection of power supply voltages. The VID pins for the processor are CMOS outputs
driven by the processor VID circuitry. Table 2 specifies the voltage level corresponding
to the state of VID[6:0]. A 1 in the table refers to a high-voltage level and a 0 refers to
a low-voltage level.
Table 2.
26
Voltage Identification Definition (Sheet 1 of 3)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VCC (V)
0
0
0
0
0
0
0
1.5000
0
0
0
0
0
0
1
1.4875
0
0
0
0
0
1
0
1.4750
0
0
0
0
0
1
1
1.4625
0
0
0
0
1
0
0
1.4500
0
0
0
0
1
0
1
1.4375
0
0
0
0
1
1
0
1.4250
0
0
0
0
1
1
1
1.4125
0
0
0
1
0
0
0
1.4000
0
0
0
1
0
0
1
1.3875
0
0
0
1
0
1
0
1.3750
0
0
0
1
0
1
1
1.3625
0
0
0
1
1
0
0
1.3500
0
0
0
1
1
0
1
1.3375
0
0
0
1
1
1
0
1.3250
0
0
0
1
1
1
1
1.3125
0
0
1
0
0
0
0
1.3000
0
0
1
0
0
0
1
1.2875
0
0
1
0
0
1
0
1.2750
0
0
1
0
0
1
1
1.2625
0
0
1
0
1
0
0
1.2500
0
0
1
0
1
0
1
1.2375
0
0
1
0
1
1
0
1.2250
0
0
1
0
1
1
1
1.2125
0
0
1
1
0
0
0
1.2000
0
0
1
1
0
0
1
1.1875
0
0
1
1
0
1
0
1.1750
0
0
1
1
0
1
1
1.1625
0
0
1
1
1
0
0
1.1500
0
0
1
1
1
0
1
1.1375
0
0
1
1
1
1
0
1.1250
0
0
1
1
1
1
1
1.1125
0
1
0
0
0
0
0
1.1000
0
1
0
0
0
0
1
1.0875
0
1
0
0
0
1
0
1.0750
0
1
0
0
0
1
1
1.0625
0
1
0
0
1
0
0
1.0500
0
1
0
0
1
0
1
1.0375
0
1
0
0
1
1
0
1.0250
0
1
0
0
1
1
1
1.0125
Datasheet
Electrical Specifications
Table 2.
Voltage Identification Definition (Sheet 2 of 3)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VCC (V)
0
1
0
1
0
0
0
1.0000
0
1
0
1
0
0
1
0.9875
0
1
0
1
0
1
0
0.9750
0
1
0
1
0
1
1
0.9625
0
1
0
1
1
0
0
0.9500
0
1
0
1
1
0
1
0.9375
0
1
0
1
1
1
0
0.9250
0
1
0
1
1
1
1
0.9125
0
1
1
0
0
0
0
0.9000
0
1
1
0
0
0
1
0.8875
0
1
1
0
0
1
0
0.8750
0
1
1
0
0
1
1
0.8625
0
1
1
0
1
0
0
0.8500
0
1
1
0
1
0
1
0.8375
0
1
1
0
1
1
0
0.8250
0
1
1
0
1
1
1
0.8125
0
1
1
1
0
0
0
0.8000
0
1
1
1
0
0
1
0.7875
0
1
1
1
0
1
0
0.7750
0
1
1
1
0
1
1
0.7625
0
1
1
1
1
0
0
0.7500
0
1
1
1
1
0
1
0.7375
0
1
1
1
1
1
0
0.7250
0
1
1
1
1
1
1
0.7125
1
0
0
0
0
0
0
0.7000
1
0
0
0
0
0
1
0.6875
1
0
0
0
0
1
0
0.6750
1
0
0
0
0
1
1
0.6625
1
0
0
0
1
0
0
0.6500
1
0
0
0
1
0
1
0.6375
1
0
0
0
1
1
0
0.6250
1
0
0
0
1
1
1
0.6125
1
0
0
1
0
0
0
0.6000
1
0
0
1
0
0
1
0.5875
1
0
0
1
0
1
0
0.5750
1
0
0
1
0
1
1
0.5625
1
0
0
1
1
0
0
0.5500
1
0
0
1
1
0
1
0.5375
1
0
0
1
1
1
0
0.5250
1
0
0
1
1
1
1
0.5125
1
0
1
0
0
0
0
0.5000
1
0
1
0
0
0
1
0.4875
1
0
1
0
0
1
0
0.4750
1
0
1
0
0
1
1
0.4625
1
0
1
0
1
0
0
0.4500
1
0
1
0
1
0
1
0.4375
1
0
1
0
1
1
0
0.4250
Datasheet
27
Electrical Specifications
Table 2.
28
Voltage Identification Definition (Sheet 3 of 3)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VCC (V)
1
0
1
0
1
1
1
0.4125
1
0
1
1
0
0
0
0.4000
1
0
1
1
0
0
1
0.3875
1
0
1
1
0
1
0
0.3750
1
0
1
1
0
1
1
0.3625
1
0
1
1
1
0
0
0.3500
1
0
1
1
1
0
1
0.3375
1
0
1
1
1
1
0
0.3250
1
0
1
1
1
1
1
0.3125
1
1
0
0
0
0
0
0.3000
1
1
0
0
0
0
1
0.2875
1
1
0
0
0
1
0
0.2750
1
1
0
0
0
1
1
0.2625
1
1
0
0
1
0
0
0.2500
1
1
0
0
1
0
1
0.2375
1
1
0
0
1
1
0
0.2250
1
1
0
0
1
1
1
0.2125
1
1
0
1
0
0
0
0.2000
1
1
0
1
0
0
1
0.1875
1
1
0
1
0
1
0
0.1750
1
1
0
1
0
1
1
0.1625
1
1
0
1
1
0
0
0.1500
1
1
0
1
1
0
1
0.1375
1
1
0
1
1
1
0
0.1250
1
1
0
1
1
1
1
0.1125
1
1
1
0
0
0
0
0.1000
1
1
1
0
0
0
1
0.0875
1
1
1
0
0
1
0
0.0750
1
1
1
0
0
1
1
0.0625
1
1
1
0
1
0
0
0.0500
1
1
1
0
1
0
1
0.0375
1
1
1
0
1
1
0
0.0250
1
1
1
0
1
1
1
0.0125
1
1
1
1
0
0
0
0.0000
1
1
1
1
0
0
1
0.0000
1
1
1
1
0
1
0
0.0000
1
1
1
1
0
1
1
0.0000
1
1
1
1
1
0
0
0.0000
1
1
1
1
1
0
1
0.0000
1
1
1
1
1
1
0
0.0000
1
1
1
1
1
1
1
0.0000
Datasheet
Electrical Specifications
3.4
Catastrophic Thermal Protection
The processor supports the THERMTRIP# signal for catastrophic thermal protection. An
external thermal sensor should also be used to protect the processor and the system
against excessive temperatures. Even with the activation of THERMTRIP#, which halts
all processor internal clocks and activity, leakage current can be high enough that the
processor cannot be protected in all conditions without the removal of power to the
processor. If the external thermal sensor detects a catastrophic processor temperature
of approximately 125°C (maximum), or if the THERMTRIP# signal is asserted, the VCC
supply to the processor must be turned off within 500 ms to prevent permanent silicon
damage due to thermal runaway of the processor. THERMTRIP# functionality is not
ensured if the PWRGOOD signal is not asserted, and during Deep Power Down
Technology State (C6).
3.5
Reserved and Unused Pins
All RESERVED (RSVD) pins must remain unconnected. Connection of these pins to VCC,
VSS, or to any other signal (including each other) can result in component malfunction
or incompatibility with future processors. See Section 4.2 for a pin listing of the
processor and the location of all RSVD pins.
For reliable operation, always connect unused inputs or bidirectional signals to an
appropriate signal level. Unused active low AGTL+ inputs may be left as no-connects if
AGTL+ termination is provided on the processor silicon. Unused active high inputs
should be connected through a resistor to ground (VSS). Unused outputs can be left
unconnected. The TEST1,TEST2,TEST3,TEST4,TEST5,TEST6,TEST7 pins are used for
test purposes internally and can be left as “No Connects”.
3.6
FSB Frequency Select Signals (BSEL[2:0])
The BSEL[2:0] signals are used to select the frequency of the processor input clock
(BCLK[1:0]). These signals should be connected to the clock chip and the appropriate
chipset on the platform. The BSEL encoding for BCLK[1:0] is shown in Table 3.
Table 3.
BSEL[2:0] Encoding for BCLK Frequency
BSEL[2]
BSEL[1]
BSEL[0]
L
L
L
BCLK Frequency
266 MHz
L
L
H
RESERVED
L
H
H
RESERVED
L
H
L
200 MHz
H
H
L
RESERVED
H
H
H
RESERVED
H
L
H
RESERVED
H
L
L
RESERVED
Datasheet
29
Electrical Specifications
3.7
FSB Signal Groups
The FSB signals have been combined into groups by buffer type in the following
sections. In this document, the term “AGTL+ Input” refers to the AGTL+ input group as
well as the AGTL+ I/O group when receiving. Similarly, “AGTL+ Output” refers to the
AGTL+ output group as well as the AGTL+ I/O group when driving.
With the implementation of a source-synchronous data bus, two sets of timing
parameters are specified. One set is for common clock signals, which are dependent
upon the rising edge of BCLK0 (ADS#, HIT#, HITM#, etc.), and the second set is for
the source-synchronous signals which are relative to their respective strobe lines (data
and address) as well as the rising edge of BCLK0. Asychronous signals are still present
(A20M#, IGNNE#, etc.) and can become active at any time during the clock cycle.
Table 4 identifies which signals are common clock, source synchronous, and
asynchronous.
Table 4.
FSB Pin Groups
Signal Group
Signals1
Type
AGTL+ Common
Clock Input
Synchronous to
BCLK[1:0]
BPRI#, DEFER#, PREQ#5, RESET#, RS[2:0]#, TRDY#
AGTL+ Common
Clock I/O
Synchronous to
BCLK[1:0]
ADS#, BNR#, BPM[3:0]#3, BR0#, DBSY#, DRDY#,
HIT#, HITM#, LOCK#, PRDY#3, DPWR#
Signals
AGTL+ Source
Synchronous
I/O
Synchronous to
assoc. strobe
Associated Strobe
REQ[4:0]#, A[16:3]#
ADSTB[0]#
A[35:17]#
ADSTB[1]#
D[15:0]#, DINV0#
DSTBP0#, DSTBN0#
D[31:16]#, DINV1#
DSTBP1#, DSTBN1#
D[47:32]#, DINV2#
DSTBP2#, DSTBN2#
D[63:48]#, DINV3#
DSTBP3#, DSTBN3#
AGTL+ Strobes
Synchronous to
BCLK[1:0]
ADSTB[1:0]#, DSTBP[3:0]#, DSTBN[3:0]#
CMOS Input
Asynchronous
A20M#, DPRSTP#, DPSLP#, IGNNE#, INIT#, LINT0/
INTR, LINT1/NMI, PWRGOOD, SMI#, SLP#, STPCLK#
Open Drain
Output
Asynchronous
FERR#, IERR#, THERMTRIP#
Open Drain I/O
Asynchronous
PROCHOT#4
CMOS Output
Asynchronous
PSI#, VID[6:0], BSEL[2:0]
CMOS Input
Synchronous to TCK TCK, TDI, TMS, TRST#
Open Drain
Output
Synchronous to TCK
FSB Clock
Clock
Power/Other
TDO
BCLK[1:0]
COMP[3:0], DBR#2, GTLREF, RSVD, TEST2, TEST1,
THERMDA, THERMDC, VCC, VCCA, VCCP, VCC_SENSE,
VSS, VSS_SENSE
NOTES:See next page
30
Datasheet
Electrical Specifications
1.
2.
Refer to Chapter 4 for signal descriptions and termination requirements.
In processor systems where there is no debug port implemented on the system board,
these signals are used to support a debug port interposer. In systems with the debug port
implemented on the system board, these signals are no connects.
BPM[2:1]# and PRDY# are AGTL+ output-only signals.
PROCHOT# signal type is open drain output and CMOS input.
On-die termination differs from other AGTL+ signals.
3.
4.
5.
3.8
CMOS Signals
CMOS input signals are shown in Table 4. Legacy output FERR#, IERR# and other nonAGTL+ signals (THERMTRIP# and PROCHOT#) use Open Drain output buffers. These
signals do not have setup or hold time specifications in relation to BCLK[1:0]. However,
all of the CMOS signals are required to be asserted for more than four BCLKs for the
processor to recognize them. See Section 3.10 for the DC specifications for the CMOS
signal groups.
3.9
Maximum Ratings
Table 5 specifies absolute maximum and minimum ratings only, which lie outside the
functional limits of the processor. Only within specified operation limits, can
functionality and long-term reliability be expected.
At conditions outside functional operation condition limits, but within absolute
maximum and minimum ratings, neither functionality nor long-term reliability can be
expected. If a device is returned to conditions within functional operation limits after
having been subjected to conditions outside these limits, but within the absolute
maximum and minimum ratings, the device may be functional, but with its lifetime
degraded depending on exposure to conditions exceeding the functional operation
condition limits.
At conditions exceeding absolute maximum and minimum ratings, neither functionality
nor long-term reliability can be expected. Moreover, if a device is subjected to these
conditions for any length of time then, when returned to conditions within the
functional operating condition limits, it will either not function, or its reliability will be
severely degraded.
Caution:
Although the processor contains protective circuitry to resist damage from static
electric discharge, precautions should always be taken to avoid high static voltages or
electric fields.
Table 5.
Processor Absolute Maximum Ratings
Symbol
Parameter
Min
Max
Unit
Notes1,2
85
°C
3,4,5
°C
6
TSTORAGE
Processor Storage Temperature
-40
TSTORAGE
Processor Storage Temperature
-25
VCC
Any Processor Supply Voltage with
Respect to VSS
-0.3
1.45
V
VinAGTL+
AGTL+ Buffer DC Input Voltage with
Respect to VSS
-0.1
1.45
V
VinAsynch_CMOS
CMOS Buffer DC Input Voltage with
Respect to VSS
-0.1
1.45
V
NOTES:
1.
For functional operation, all processor electrical, signal quality, mechanical and thermal
specifications must be satisfied.
Datasheet
31
Electrical Specifications
2.
3.
4.
5.
6.
3.10
Excessive overshoot or undershoot on any signal will likely result in permanent damage to
the processor.
Storage temperature is applicable to storage conditions only. In this scenario, the
processor must not receive a clock, and no lands can be connected to a voltage bias.
Storage within these limits will not affect the long-term reliability of the device. For
functional operation, please refer to the processor case temperature specifications.
This rating applies to the processor and does not include any tray or packaging.
Failure to adhere to this specification can affect the long-term reliability of the processor.
For Intel® Core™2 Duo mobile processors in 22x22 mm package.
Processor DC Specifications
The processor DC specifications in this section are defined at the processor
core (pads) unless noted otherwise.
The tables list the DC specifications for the processor and are valid only while meeting
specifications for junction temperature, clock frequency, and input voltages. The
Highest Frequency Mode (HFM) and Lowest Frequency Mode (LFM) refer to the highest
and lowest core operating frequencies supported on the processor. Active mode load
line specifications apply in all states except in the Deep Sleep and Deeper Sleep states.
VCC,BOOT is the default voltage driven by the voltage regulator at power up in order to
set the VID values. Unless specified otherwise, all specifications for the processor are at
TJ = 105 °C. Read all notes associated with each parameter.
Table 6.
Voltage and Current Specifications for the Dual-Core, Extreme Edition
Processors (Sheet 1 of 2)
Symbol
Parameter
Min
VCCDAM
VCC in Enhanced Intel® Dynamic Acceleration
Technology Mode
1.0
VCCHFM
VCC at Highest Frequency Mode (HFM)
1.0
VCCLFM
VCC at Lowest Frequency Mode (LFM)
VCCSLFM
VCC at Super Low Frequency Mode
(Super LFM)
VCC,BOOT
Default VCC Voltage for Initial Power Up
VCCP
AGTL+ Termination Voltage
VCCA
PLL Supply Voltage
VCCDPRSLP
VCC at Deeper Sleep
VDC4
Max
Unit
Notes
1.325
V
1, 2
—
1.275
V
1, 2
0.85
—
1.1
V
1, 2
0.8
—
1.0
V
1, 2
—
1.20
V
2, 6
1.00
1.05
1.10
V
1.425
1.5
1.575
V
0.65
—
0.85
V
1, 2
VCC at Intel® Enhanced Deeper Sleep State
0.6
—
0.85
V
1, 2
VCCDPPWDN
VCC at Deep Power Down Technology State
(C6)
0.35
—
0.7
V
ICCDES
ICC for Processors Recommended Design
Target
—
—
60
A
12
ICC for Processors
—
—
—
Processor
Number
Core Frequency/Voltage
—
—
—
3.06 GHz & VCCHFM
1.6 GHz & VCCLFM
0.8 GHz & VCCSLFM
—
—
59
34
24
A
3, 4, 10
ICC
32
X9100
Typ
Datasheet
Electrical Specifications
Table 6.
Voltage and Current Specifications for the Dual-Core, Extreme Edition
Processors (Sheet 2 of 2)
Symbol
Parameter
Min
Typ
Max
Unit
Notes
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
SuperLFM
—
—
29.7
16.7
A
3, 4, 10
ISLP
ICC Sleep
HFM
SuperLFM
—
—
28.8
16.5
A
3, 4, 10
IDSLP
ICC Deep Sleep
HFM
SuperLFM
—
—
26.8
16.0
A
3, 4, 10
IDPRSLP
ICC Deeper Sleep (C4)
—
—
12.2
A
3, 4
IDC4
ICC Intel Enhanced Deeper Sleep State
—
—
11.7
A
3, 4
IPPWDN
ICC Deep Power Down Technology State (C6)
—
—
11.0
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at
Processor Package Pin
—
—
600
mA/µs
5, 7
ICCA
ICC for VCCA Supply
—
—
130
mA
ICCP
ICC for VCCP Supply before VCC Stable
ICC for VCCP Supply after VCC Stable
—
—
4.5
2.5
A
A
8
9
NOTES:
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
2.
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-MΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
3.
Specified at 105 °C TJ.
4.
Specified at the nominal VCC.
5.
Measured at the bulk capacitors on the motherboard.
6.
VCC,BOOT tolerance shown in Figure 4 and Figure 5.
7.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
8.
This is a power-up peak current specification, which is applicable when VCCP is high and VCC_CORE is low.
9.
This is a steady-state ICC current specification, which is applicable when both VCCP and VCC_CORE are high.
10.
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor will be lesser than or
equal to 300 mV.
11.
The ICCDES (max) specification of 60 A is for Intel® Core™2 Extreme processors only.
Datasheet
33
Electrical Specifications
Table 7.
Voltage and Current Specifications for the Dual-Core, Standard-Voltage
Processors
Symbol
Parameter
Min
Typ
Max
Unit
Notes
VCCDAM
VCC in Enhanced Intel® Dynamic Acceleration
Technology Mode
1.0
1.3
V
1, 2
VCCHFM
VCC at Highest Frequency Mode (HFM)
1.0
1.25
V
1, 2
VCCLFM
VCC at Lowest Frequency Mode (LFM)
0.85
—
1.1
V
1, 2
0.75
—
0.95
V
1, 2
—
1.2
—
V
2, 6
1.0
1.05
1.1
V
1.425
1.5
1.575
V
0.65
—
0.85
V
1, 2
0.6
—
0.85
V
1, 2
VCCSLFM
VCC at Super Low Frequency Mode (Super LFM)
VCC,BOOT
Default VCC Voltage for Initial Power Up
VCCP
AGTL+ Termination Voltage
VCCA
PLL Supply Voltage
VCCDPRSLP
VCC at Deeper Sleep
VDC4
VCC at Intel® Enhanced Deeper Sleep State
VCCDPPWDN
VCC at Deep Power Down Technology State (C6)
0.35
—
0.7
V
1, 2
ICCDES
ICC for Processors Recommended Design Target
—
—
47
A
12
ICC for Processors
—
—
—
—
—
—
—
—
47
47
47
47
47
31.4
22.4
A
3, 4, 10
Processor
Number
ICC
T9900
T9800
T9600
T9550
T9400
Core Frequency/Voltage
3.06 GHz & VCCHFM
2.93 GHz & VCCHFM
2.80 GHz & VCCHFM
2.66 GHz & VCCHFM
2.53 GHz & VCCHFM
1.6 GHz & VCCLFM
0.8 GHz & VCCSLFM
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
SuperLFM
—
—
25.4
13.7
A
3, 4, 10
ISLP
ICC Sleep
HFM
SuperLFM
—
—
24.7
13.5
A
3, 4, 10
IDSLP
ICC Deep Sleep
HFM
SuperLFM
—
—
22.9
13.0
A
3, 4, 10
IDPRSLP
ICC Deeper Sleep (C4)
—
—
11.7
A
3, 4
IDC4
ICC Intel Enhanced Deeper Sleep
—
—
10.5
A
3, 4
IPPWDN
ICC Deep Power Down Technology State (C6)
—
—
5.7
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at Processor
Package Pin
—
—
600
mA/µs
5, 7
ICCA
ICC for VCCA Supply
—
—
130
mA
ICCP
ICCC for VCCP Supply before VCC Stable
ICC for VCCP Supply after VCC Stable
—
—
4.5
2.5
A
A
8
9
NOTES:See next page.
34
Datasheet
Electrical Specifications
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-MΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
Specified at 105 °C TJ.
Specified at the nominal VCC.
Measured at the bulk capacitors on the motherboard.
VCC,BOOT tolerance shown in Figure 7 and Figure 8.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
This is a power-up peak current specification that is applicable when VCCP is high and VCC_CORE is low.
This is a steady-state ICCcurrent specification that is applicable when both VCCP and VCC_CORE are high.
Processor ICC requirements in Intel Dynamic Acceleration Technology mode are lesser than ICC in HFM
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor will be lesser than or
equal to 300 mV.
Instantaneous current ICC_CORE_INST of 57 A has to be sustained for short time (tINST) of 35 µs. Average
current will be less than maximum specified ICCDES. VR OCP threshold should be high enough to support
current levels described herein.
Table 8.
Voltage and Current Specifications for the Dual-Core, Low-Power
Standard-Voltage Processors (25 W) in Standard Package
Symbol
Parameter
Min
Typ
Max
Unit
Notes
1.3
V
1, 2
VCCDAM
VCC in Enhanced Intel® Dynamic Acceleration
Technology Mode
VCCHFM
VCC at Highest Frequency Mode (HFM)
0.9
1.25
V
1, 2
VCCLFM
VCC at Lowest Frequency Mode (LFM)
0.85
—
1.025
V
1, 2
VCCSLFM
VCC at Super Low Frequency Mode (Super LFM)
0.75
—
0.95
V
1, 2
VCC,BOOT
Default VCC Voltage for Initial Power Up
—
1.2
—
V
2, 6
VCCP
AGTL+ Termination Voltage
VCCA
PLL Supply Voltage
VCCDPRSLP
VCC at Deeper Sleep
VDC4
VCC at Intel® Enhanced Deeper Sleep State
VCCDPPWDN
VCC at Deep Power Down Technology State (C6)
ICCDES
ICC for Processors Recommended Design Target
ICC for Processors
Processor
Number
ICC
P9700
P9600
P8800
P9500
P8700
P8600
P8400
Core Frequency/Voltage
2.8 GHz & VCCHFM
2.667 GHz & VCCHFM
2.667 GHz & VCCHFM
2.53 GHz & VCCHFM
2.53 GHz & VCCHFM
2.4 GHz & VCCHFM
2.267 GHz & VCCHFM
1.6 GHz & VCCLFM
0.8 GHz & VCCSLFM
0.9
1.0
1.05
1.1
V
1.425
1.5
1.575
V
0.65
—
0.85
V
1, 2
0.6
—
0.85
V
1, 2
0.35
—
0.7
V
1, 2
—
—
38
A
12
—
—
—
—
—
—
—
38
38
38
38
38
38
38
27.7
17.5
A
3, 4, 10
—
Datasheet
35
Electrical Specifications
Table 8.
Voltage and Current Specifications for the Dual-Core, Low-Power
Standard-Voltage Processors (25 W) in Standard Package
Symbol
Parameter
Min
Typ
Max
Unit
Notes
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
SuperLFM
—
—
15.3
10.5
A
3, 4, 10
ISLP
ICC Sleep
HFM
SuperLFM
—
—
14.6
10.3
A
3, 4, 10
IDSLP
ICC Deep Sleep
HFM
SuperLFM
—
—
12.9
9.8
A
3, 4, 10
IDPRSLP
ICC Deeper Sleep
—
—
7.3
A
3, 4
IDC4
ICC Intel Enhanced Deeper Sleep
—
—
6.7
A
3, 4
IPPWDN
ICC Deep Power Down Technology State (C6)
—
—
4.3
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at Processor
Package Pin
—
—
600
mA/µs
5, 7
ICCA
ICC for VCCA Supply
—
—
130
mA
ICCP
ICCC for VCCP Supply before VCC Stable
ICC for VCCP Supply after VCC Stable
—
—
4.5
2.5
A
A
8
9
NOTES:.
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
2.
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-MΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
3.
Specified at 105 °C TJ.
4.
Specified at the nominal VCC.
5.
Measured at the bulk capacitors on the motherboard.
6.
VCC,BOOT tolerance shown in Figure 4 and Figure 5.
7.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
8.
This is a power-up peak current specification that is applicable when VCCP is high and VCC_CORE is low.
9.
This is a steady-state ICCcurrent specification that is applicable when both VCCP and VCC_CORE are high.
10.
Processor ICC requirements in Intel Dynamic Acceleration Technology mode are lesser than ICC in HFM
11.
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor will be lesser than or
equal to 300 mV.
12.
Instantaneous current ICC_CORE_INST of 49 A has to be sustained for short time (tINST) of 35 µs. Average
current will be less than maximum specified ICCDES. VR OCP threshold should be high enough to support
current levels described herein.
36
Datasheet
Electrical Specifications
Table 9.
Voltage and Current Specifications for the Dual-Core, Power Optimized
Performance (25 W) SFF Processors
Symbol
Parameter
Min
Typ
Max
Unit
Notes
VCCDAM
VCC in Enhanced Intel® Dynamic Acceleration
Technology Mode
0.9
—
1.275
V
1, 2
VCCHFM
VCC at Highest Frequency Mode (HFM)
0.9
—
1.2125
V
1, 2
VCCLFM
VCC at Lowest Frequency Mode (LFM)
0.85
—
1.025
V
1, 2
VCCSLFM
VCC at Super Low Frequency Mode (Super LFM)
0.75
—
0.95
V
1, 2
VCC,BOOT
Default VCC Voltage for Initial Power Up
—
1.20
—
V
2, 6, 8
VCCP
AGTL+ Termination Voltage
1.00
1.05
1.10
V
VCCA
PLL Supply Voltage
1.425
1.5
1.575
V
VCCDPRSLP
VCC at Deeper Sleep
0.65
—
0.85
V
1, 2
VDC4
VCC at Intel® Enhanced Deeper Sleep State
0.6
—
0.85
V
1, 2
VCCDPPWDN
VCC at Deep Power Down Technology State (C6)
0.35
—
0.7
V
1, 2
ICCDES
ICC for Processors Recommended Design Target
—
—
37
A
5
Processor
Number
Core Frequency/Voltage
—
—
—
SP9600
2.53 GHz & VCCHFM
SP9400
2.4 GHz & VCCHFM
SP9300
2.26 GHz & VCCHFM
—
—
37
37
37
28
17
A
3, 4, 12
14.8
8.8
A
3, 4, 12
ICC
1.2 GHz & VCCLFM
0.8 GHz & VCCSLFM
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
SuperLFM
—
—
ISLP
ICC Sleep
HFM
SuperLFM
—
—
14.2
8.6
A
3, 4, 12
IDSLP
ICC Deep Sleep
HFM
SuperLFM
—
—
12.5
8.1
A
3, 4, 12
IDPRSLP
ICC Deeper Sleep
—
—
6.9
A
3, 4
IDC4
ICC Intel Enhanced Deeper Sleep State
—
—
5.9
A
3, 4
IDPWDN
ICC Deep Power Down Technology State (C6)
—
—
3.5
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at Processor
Package Pin
—
—
600
mA/µs
7, 9
ICCA
ICC for VCCA Supply
—
—
130
mA
ICCP
ICC for VCCP Supply before VCC Stable
ICC for VCCPSupply after VCC Stable
—
—
4.5
2.5
A
A
10
11
NOTES:
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
Datasheet
37
Electrical Specifications
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-MΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
Specified at 105 °C TJ.
Specified at the nominal VCC.
Measured at the bulk capacitors on the motherboard.
VCC,BOOT tolerance shown in Figure 7 and Figure 8.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
This is a power-up peak current specification that is applicable when VCCP is high and VCC_CORE is low.
This is a steady-state ICC current specification that is applicable when both VCCP and VCC_CORE are high.
Processor ICC requirements in Intel Dynamic Acceleration Technology mode are lesser than ICC in HFM
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor will be lesser than or
equal to 300 mV.
Instantaneous current ICC_CORE_INST of 44 A has to be sustained for short time (tINST) of 35 µs. Average
current will be less than maximum specified ICCDES. VR OCP threshold should be high enough to support
current levels described herein.
Table 10.
Voltage and Current Specifications for the Dual-Core, Low-Voltage SFF
Processor
Symbol
Parameter
Min
Typ
Max
Unit
Notes
VCCDAM
VCC in Enhanced Intel® Dynamic Acceleration
Technology Mode
0.9
—
1.25
V
1, 2
VCCHFM
VCC at Highest Frequency Mode (HFM)
0.9
—
1.175
V
1, 2
VCCLFM
VCC at Lowest Frequency Mode (LFM)
0.85
—
1.025
V
1, 2
VCCSLFM
VCC at Super Low Frequency Mode (Super LFM)
0.75
—
0.95
V
1, 2
VCC,BOOT
Default VCC Voltage for Initial Power Up
—
1.20
—
V
2, 6, 8
VCCP
AGTL+ Termination Voltage
1.00
1.05
1.10
V
VCCA
PLL Supply Voltage
1.425
1.5
1.575
V
VCCDPRSLP
VCC at Deeper Sleep
0.65
—
0.85
V
1, 2
VDC4
VCC at Intel® Enhanced Deeper Sleep State
0.6
—
0.85
V
1, 2
VCCDPPWDN
VCC at Deep Power Down Technology State (C6)
0.35
—
0.7
V
1, 2
ICCDES
ICC for Processors Recommended Design Target
—
—
27
A
5
Processor
Number
—
—
—
—
—
27
27
27
25.5
15
A
3, 4, 12
SL9600
ICC
SL9400
SL9300
Core Frequency/Voltage
2.13 GHz & VCCHFM
1.86 GHz & VCCHFM
1.6 GHz & VCCHFM
1.6 GHz & VCCLFM
0.8 GHz & VCCSLFM
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
SuperLFM
—
—
12.3
8.2
A
3, 4, 12
ISLP
ICC Sleep
HFM
SuperLFM
—
—
11.8
8.0
A
3, 4, 12
38
Datasheet
Electrical Specifications
Table 10.
Voltage and Current Specifications for the Dual-Core, Low-Voltage SFF
Processor
Symbol
Parameter
Min
Typ
Max
Unit
Notes
IDSLP
ICC Deep Sleep
HFM
SuperLFM
—
—
10.5
7.5
A
3, 4, 12
IDPRSLP
ICC Deeper Sleep
—
—
6.5
A
3, 4
IDC4
ICC Intel Enhanced Deeper Sleep
—
—
5.6
A
3, 4
IDPWDN
ICC Deep Power Down Technology State (C6)
—
—
3.2
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at Processor
Package Pin
—
—
600
mA/µs
7, 9
ICCA
ICC for VCCA Supply
—
—
130
mA
ICCP
ICC for VCCP Supply before VCC Stable
ICC for VCCP Supply after VCC Stable
—
4.5
2.5
A
A
—
10
11
NOTES:
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
2.
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-MΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
3.
Specified at 105 °C TJ.
4.
Specified at the nominal VCC.
5.
Measured at the bulk capacitors on the motherboard.
6.
VCC,BOOT tolerance shown in Figure 7 and Figure 8.
7.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
8.
This is a power-up peak current specification that is applicable when VCCP is high and VCC_CORE is low.
9.
This is a steady-state ICC current specification that is applicable when both VCCP and VCC_CORE are high.
10.
Processor ICC requirements in Intel Dynamic Acceleration Technology mode are lesser than ICC in HFM
11.
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor will be lesser than or
equal to 300 mV.
12.
Instantaneous current ICC_CORE_INST of 36 A has to be sustained for short time (tINST) of 35 µs. Average
current will be less than maximum specified ICCDES. VR OCP threshold should be high enough to support
current levels described herein.
Datasheet
39
Electrical Specifications
Table 11.
Voltage and Current Specifications for the Dual-Core, Ultra-Low-Voltage SFF
Processor
Symbol
Parameter
VCCDAM
VCC in Enhanced Intel® Dynamic Acceleration
Technology Mode
Min
Typ
Max
Unit
Notes
0.8
—
1.1625
V
1, 2
VCCHFM
VCC at Highest Frequency Mode (HFM)
0.775
—
1.1
V
1, 2
VCCLFM
VCC at Lowest Frequency Mode (LFM)
0.8
—
0.975
V
1, 2
VCCSLFM
VCC at Super Low Frequency Mode (Super LFM)
0.725
—
0.925
V
1, 2
VCC,BOOT
Default VCC Voltage for Initial Power Up
—
1.20
—
V
2, 6, 8
VCCP
AGTL+ Termination Voltage
VCCA
PLL Supply Voltage
VCCDPRSLP
VCC at Deeper Sleep
VDC4
VCC at Intel® Enhanced Deeper Sleep State
VCCDPPWDN
VCC at Deep Power Down Technology State (C6)
ICCDES
ICC for Processors Recommended Design Target
Processor
Number
ICC
SU9600
SU9400
SU9300
Core Frequency/Voltage
1.6
1.4
1.2
1.2
0.8
GHz
GHz
GHz
GHz
GHz
&
&
&
&
&
VCCHFM
VCCHFM
VCCHFM
VCCLFM
VCCSLFM
1.00
1.05
1.10
V
1.425
1.5
1.575
V
0.65
—
0.8
V
1, 2
0.6
—
0.8
V
1, 2
0.35
—
0.6
V
1, 2
—
—
18
A
5
—
—
—
—
—
18
18
18
18
13
A
3, 4, 12
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
SuperLFM
—
—
6.3
4.4
A
3, 4, 12
ISLP
ICC Sleep
HFM
SuperLFM
—
—
5.9
4.2
A
3, 4, 12
IDSLP
ICC Deep Sleep
HFM
SuperLFM
—
—
5.0
3.7
A
3, 4, 12
IDPRSLP
ICC Deeper Sleep
—
—
3.2
A
3, 4
IDC4
ICC Intel Enhanced Deeper Sleep State
—
—
2.8
A
3, 4
IDPWDN
ICC Deep Power Down Technology State (C6)
—
—
2.4
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at Processor
Package Pin
—
—
600
mA/µs
7, 9
ICCA
ICC for VCCA Supply
—
—
130
mA
ICCP
ICC for VCCP Supply before VCC Stable
ICC for VCCPSupply after VCC Stable
—
—
4.5
2.5
A
A
10
11
NOTES:See next page.
40
Datasheet
Electrical Specifications
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-MΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
Specified at 105 °C TJ.
Specified at the nominal VCC.
Measured at the bulk capacitors on the motherboard.
VCC,BOOT tolerance shown in Figure 7 and Figure 8.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
This is a power-up peak current specification that is applicable when VCCP is high and VCC_CORE is low.
This is a steady-state ICC current specification that is applicable when both VCCP and VCC_CORE are high.
Processor ICC requirements in Intel Dynamic Acceleration Technology mode are lesser than ICC in HFM
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor will be lesser than or
equal to 300 mV.
Instantaneous current ICC_CORE_INST of 24 A has to be sustained for short time (tINST) of 35µs. Average
current will be less than maximum specified ICCDES. VR OCP threshold should be high enough to support
current levels described herein.
Table 12.
Voltage and Current Specifications for the Ultra-Low-Voltage, Single-Core
(5.5 W) SFF Processor
Symbol
Parameter
Min
Typ
Max
Unit
Notes
VCCHFM
VCC at Highest Frequency Mode (HFM)
0.775
—
1.1
V
1, 2
VCCLFM
VCC at Lowest Frequency Mode (LFM)
0.8
—
0.975
V
1, 2
VCCSLFM
VCC at Super Low Frequency Mode (Super LFM)
0.725
—
0.925
V
1, 2
2, 6, 8
VCC,BOOT
Default VCC Voltage for Initial Power Up
VCCP
AGTL+ Termination Voltage
VCCA
PLL Supply Voltage
VCCDPRSLP
VCC at Deeper Sleep
VDC4
VCC at Intel® Enhanced Deeper Sleep State
0.6
—
0.8
V
1, 2
VCCDPPWDN
VCC at Deep Power Down Technology State (C6)
0.35
—
0.6
V
1, 2
ICCDES
ICC for Processors Recommended Design Target
—
—
9
A
5
Processor
Number
—
—
—
—
—
9
9
9
7
A
3, 4, 12
ICC
SU3500
SU3300
Core Frequency/Voltage
1.4
1.2
1.2
0.8
GHz
GHz
GHz
GHz
&
&
&
&
VCCHFM
VCCHFM
VCCLFM
VCCSLFM
—
1.20
—
V
1.00
1.05
1.10
V
1.425
1.5
1.575
V
0.65
—
0.8
V
1, 2
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
SuperLFM
—
—
4.4
3.7
A
3, 4, 12
ISLP
ICC Sleep
HFM
SuperLFM
—
—
4.1
3.5
A
3, 4, 12
Datasheet
41
Electrical Specifications
Table 12.
Voltage and Current Specifications for the Ultra-Low-Voltage, Single-Core
(5.5 W) SFF Processor
Symbol
Parameter
Min
Typ
Max
Unit
Notes
IDSLP
ICC Deep Sleep
HFM
SuperLFM
—
—
3.3
3.0
A
3, 4, 12
IDPRSLP
ICC Deeper Sleep
—
—
2.1
A
3, 4
IDC4
ICC Intel Enhanced Deeper Sleep State
—
—
1.9
A
3, 4
IDPWDN
ICC Deep Power Down Technology State (C6)
—
—
1.7
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at Processor
Package Pin
—
—
600
mA/µs
7, 9
ICCA
ICC for VCCA Supply
—
—
130
mA
ICCP
ICC for VCCP Supply before VCC Stable
ICC for VCCPSupply after VCC Stable
—
4.5
2.5
A
A
—
10
11
NOTES:
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
2.
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-MΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
3.
Specified at 100 °C TJ.
4.
Specified at the nominal VCC.
5.
Measured at the bulk capacitors on the motherboard.
6.
VCC,BOOT tolerance shown in Figure 4 and Figure 5.
7.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
8.
This is a power-up peak current specification that is applicable when VCCP is high and VCC_CORE is low.
9.
This is a steady-state ICC current specification that is applicable when both VCCP and VCC_CORE are high.
10.
Processor ICC requirements in Intel Dynamic Acceleration Technology mode are lesser than ICC in HFM
11.
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor will be lesser than or
equal to 300 mV.
42
Datasheet
Electrical Specifications
Figure 4.
Active VCC and ICC Loadline for Standard Voltage, Low-Power SV (25 W) and
Dual-Core, Extreme Edition Processors
VCC-CORE [V]
Slope = -2.1 mV/A at package
VccSense, VssSense pins.
Differential Remote Sense required.
VCC-CORE max {HFM|LFM}
VCC-CORE, DC max {HFM|LFM}
10mV= RIPPLE
VCC-CORE nom {HFM|LFM}
VCC-CORE, DC min {HFM|LFM}
VCC-CORE min {HFM|LFM}
+/-VCC-CORE Tolerance
= VR St. Pt. Error 1/
0
ICC-CORE max
{HFM|LFM}
ICC-CORE
[A]
Note 1 / V C C - C O R E S et P oi n t Er ro r T o l er a nce i s pe r b el o w :
T ol e ra n c e
-- - - -- - - -- - -- - + / - 1. 5%
+ / - 11 .5 mV
V C C - C O R E V ID V ol t ag e R an ge
-- - - -- - - -- - -- - - -- - - -- - - -- - - -- - -- - - -- - - -- - - -- - - -- - -- - - -- V C C - C O R E > 0 .7 50 0 V
0 . 50 00 V < /= V c c _ c o r e </ = 0. 75 00 0 V
Datasheet
43
Electrical Specifications
Figure 5.
Deeper Sleep VCC and ICC Loadline for Standard-Voltage, Low-Power SV
(25 W) and Dual-Core Extreme Edition Processors
VCC-CORE [V]
Slope = -2.1 mV/A at package
VccSense, VssSense pins.
Differential Remote Sense required.
VCC-CORE max {HFM|LFM}
VCC-CORE, DC max {HFM|LFM}
13mV= RIPPLE
VCC-CORE nom {HFM|LFM}
VCC-CORE, DC min {HFM|LFM}
VCC-CORE min {HFM|LFM}
+/-VCC-CORE Tolerance
= VR St. Pt. Error 1/
0
Note 1/ V C C - C O R E Set Point Error Tolerance is per below :
ICC-CORE max
{HFM|LFM}
ICC-CORE
[A]
Tolerance
V C C - C O R E VID Voltage Range
--------------- -------------------------------------------------------+/-[(VID*1.5%)-3mV]
V C C - C O R E > 0.7500V
+/-(11.5mV-3mV)
0.5000V </= V C C - C O R E </= 0.7500V
Total tolerance window
including ripple is +/-35mV for C6
0.3000V </= V C C - C O R E < 0.5000V
NOTE: Deeper Sleep mode tolerance depends on VID value.
44
Datasheet
Electrical Specifications
Figure 6.
Deeper Sleep VCC and ICC Loadline for Low-Power Standard-Voltage
Processors
VCC-CORE [V]
Slope = -4.0 mV/A at package
VccSense, VssSense pins.
Differential Remote Sense required.
VCC-CORE max {HFM|LFM}
VCC-CORE, DC max {HFM|LFM}
10mV= RIPPLE
VCC-CORE nom
{HFM|LFM}
VCC-CORE, DC min
{HFM|LFM}
+/-VCC-CORE Tolerance
= VR St. Pt. Error 1/
VCC-CORE min {HFM|LFM}
0
ICC-CORE max
{HFM|LFM}
ICC-CORE
[A]
Note 1/ V CC- CORE Set Point Error Tolerance is per below :
Tolerance
V CC- CORE VID Voltage Range
--------------- -------------------------------------------------------+/-[(VID*1.5%)-3mV]
V CC- CORE > 0.7500V
+/-(11.5mV-3mV)
0.5000V </= V CC- CORE </= 0.7500V
Total tolerance window
including ripple is +/-35mV for C6
0.3000V </= V CC- CORE < 0.5000V
NOTES:
1.
Applies to low-power standard-voltage 22-mm (dual-core) processors.
2.
Deeper Sleep mode tolerance depends on VID value.
Datasheet
45
Electrical Specifications
Figure 7.
Active VCC and ICC Loadline for Low-Voltage, Ultra-Low-Voltage and Power
Optimized Performance Processor
VCC-CORE [V]
Slope = -4.0 mV/A at package
VccSense, VssSense pins.
Differential Remote Sense required.
VCC-CORE max {HFM|LFM}
VCC-CORE, DC max {HFM|LFM}
10mV= RIPPLE
VCC-CORE nom {HFM|LFM}
VCC-CORE, DC min {HFM|LFM}
VCC-CORE min {HFM|LFM}
+/-VCC-CORE Tolerance
= VR St. Pt. Error 1/
0
ICC-CORE max
Note 1/ V C C - C O R E Set Point Error Tolerance is per below : {HFM|LFM}
ICC-CORE
[A]
Tolerance
V C C - C O R E VID Voltage Range
--------------- -------------------------------------------------------+/-1.5%
V C C - C O R E > 0.7500V
+/-11.5mV
0.5000V </= V C C - C O R E </= 0.7500V
+/-25mV
0.3000V </= V C C - C O R E < 0.5000V
NOTES:
1.
Applies to Low-Voltage, Ultra-Low-Voltage and Power Optimised Performance processors in
22 mmx22 mm package.
2.
Active mode tolerance depends on VID value
46
Datasheet
Electrical Specifications
Figure 8.
Deeper Sleep VCC and ICC Loadline for Low-Voltage, Ultra-Low-Voltage and
Power Optimized Performance Processor
VCC-CORE [V]
Slope = -4.0 mV/A at package
VccSense, VssSense pins.
Differential Remote Sense required.
VCC-CORE max {HFM|LFM}
VCC-CORE, DC max {HFM|LFM}
10mV= RIPPLE
VCC-CORE nom
{HFM|LFM}
VCC-CORE, DC min
{HFM|LFM}
+/-VCC-CORE Tolerance
= VR St. Pt. Error 1/
VCC-CORE min {HFM|LFM}
0
ICC-CORE max
{HFM|LFM}
ICC-CORE
[A]
Note 1/ V CC- CORE Set Point Error Tolerance is per below :
Tolerance
V CC- CORE VID Voltage Range
--------------- -------------------------------------------------------+/-[(VID*1.5%)-3mV]
V CC- CORE > 0.7500V
+/-(11.5mV-3mV)
0.5000V </= V CC- CORE </= 0.7500V
Total tolerance window
including ripple is +/-35mV for C6
0.3000V </= V CC- CORE < 0.5000V
NOTES:
1.
Applies to Low-Voltage, Ultra-Low-Voltage and Power Optimised Performance processors in
22 mmx22 mm package.
2.
Deeper Sleep mode tolerance depends on VID value.
Datasheet
47
Electrical Specifications
Table 13.
Symbol
VCCP
GTLREF
AGTL+ Signal Group DC Specifications
Parameter
I/O Voltage
Reference Voltage
Min
Typ
Max
Unit
1.00
1.05
1.10
V
Notes1
0.65
0.70
0.72
V
6
27.23
27.5
27.78
Ω
10
Termination Resistor Address
49
55
63
Ω
11, 12
Termination Resistor Data
49
55
63
Ω
11, 13
RCOMP
Compensation Resistor
RODT/A
RODT/D
49
55
63
Ω
11, 14
VIH
Input High Voltage
0.82
1.05
1.20
V
3,6
VIL
Input Low Voltage
-0.10
0
0.55
V
2,4
VOH
Output High Voltage
0.90
VCCP
1.10
V
6
RODT/Cntrl
Termination Resistor Control
RTT/A
Termination Resistance Address
50
55
61
Ω
7, 12
RTT/D
Termination Resistance Data
50
55
61
Ω
7, 13
Termination Resistance Control
50
55
61
Ω
7, 14
RON/A
Buffer On Resistance Address
23
25
29
Ω
5, 12
RON/D
Buffer On Resistance Data
23
25
29
Ω
5, 13
Buffer On Resistance Control
23
25
29
Ω
5, 14
Input Leakage Current
—
—
± 100
µA
8
1.80
2.30
2.75
pF
9
RTT/Cntrl
RON/Cntrl
ILI
Cpad
Pad Capacitance
NOTES:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
VIL is defined as the maximum voltage level at a receiving agent that will be interpreted as a logical low
value.
3.
VIH is defined as the minimum voltage level at a receiving agent that will be interpreted as a logical high
value.
4.
VIH and VOH may experience excursions above VCCP. However, input signal drivers must comply with the
signal quality specifications.
5.
This is the pulldown driver resistance. Measured at 0.31*VCCP. RON (min) = 0.418*RTT, RON (typ) =
0.455*RTT,
RON (max) = 0.527*RTT. RTT typical value of 55 Ω is used for RON typ/min/max calculations.
6.
GTLREF should be generated from VCCP with a 1% tolerance resistor divider. The VCCP referred to in these
specifications is the instantaneous VCCP.
7.
RTT is the on-die termination resistance measured at VOL of the AGTL+ output driver. Measured at
0.31*VCCP. RTT is connected to VCCP on die. Refer to processor I/O buffer models for I/V characteristics.
8.
Specified with on-die RTT and RON turned off. Vin between 0 and VCCP.
9.
Cpad includes die capacitance only. No package parasitics are included.
10.
This is the external resistor on the comp pins.
11.
On-die termination resistance, measured at 0.33*VCCP.
12.
Applies to Signals A[35:3].
13.
Applies to Signals D[63:0].
14.
Applies to Signals BPRI#, DEFER#, PREQ#, PREST#, RS[2:0]#, TRDY#, ADS#, BNR#, BPM[3:0], BR0#,
DBSY#, DRDY#, HIT#, HITM#, LOCK#, PRDY#, DPWR#, DSTB[1:0]#, DSTBP[3:0] and DSTBN[3:0]#.
48
Datasheet
Electrical Specifications
Table 14.
CMOS Signal Group DC Specifications
Symbol
VCCP
Parameter
I/O Voltage
Min
Typ
Max
Unit
1.00
1.05
1.10
V
Notes1
VIL
Input Low Voltage CMOS
-0.10
0.00
0.3*VCCP
V
2
VIH
Input High Voltage
0.7*VCCP
VCCP
VCCP+0.1
V
2
VOL
Output Low Voltage
-0.10
0
0.1*VCCP
V
2
VOH
Output High Voltage
0.9*VCCP
VCCP
VCCP+0.1
V
2
IOL
Output Low Current
1.5
—
4.1
mA
3
IOH
Output High Current
1.5
—
4.1
mA
4
ILI
Input Leakage Current
—
—
±100
µA
5
Cpad1
Pad Capacitance
1.80
2.30
2.75
pF
6
Cpad2
Pad Capacitance for CMOS Input
0.95
1.2
1.45
pF
7
NOTES:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
The VCCP referred to in these specifications refers to instantaneous VCCP.
3.
Measured at 0.1 *VCCP.
4.
Measured at 0.9 *VCCP.
5.
For Vin between 0 V and VCCP. Measured when the driver is tristated.
6.
Cpad1 includes die capacitance only for DPRSTP#, DPSLP#, PWRGOOD. No package parasitics are
included.
7.
Cpad2 includes die capacitance for all other CMOS input signals. No package parasitics are included.
Table 15.
Symbol
Open Drain Signal Group DC Specifications
Parameter
Min
Typ
Max
Unit
Notes1
3
VOH
Output High Voltage
VCCP–5%
VCCP
VCCP+5%
V
VOL
Output Low Voltage
0
—
0.20
V
IOL
Output Low Current
16
—
50
mA
2
ILO
Output Leakage Current
—
—
±200
µA
4
1.80
2.30
2.75
pF
5
Cpad
Pad Capacitance
NOTES:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
Measured at 0.2 V.
3.
VOH is determined by value of the external pull-up resistor to VCCP.
4.
For Vin between 0 V and VOH.
5.
Cpad includes die capacitance only. No package parasitics are included.
§
Datasheet
49
Electrical Specifications
50
Datasheet
Package Mechanical Specifications and Pin Information
4
Package Mechanical
Specifications and Pin
Information
4.1
Package Mechanical Specifications
The processor (XE and SV) is available in 478-pin Micro-FCPGA packages as well as
479-ball Micro-FCBGA packages. The package mechanical dimensions are shown in
Figure 9 through Figure 13.
The processor (POP, LV, ULV DC and ULV SC) is available 956-ball Micro-FCBGA
packages. The package mechanical dimensions are shown in Figure 14 and Figure 15.
The maximum outgoing co-planarity is 0.2 mm (8 mils) for SFF processors.
The mechanical package pressure specifications are in a direction normal to the surface
of the processor. This protects the processor die from fracture risk due to uneven die
pressure distribution under tilt, stack-up tolerances and other similar conditions. These
specifications assume that a mechanical attach is designed specifically to load one type
of processor.
A 15-lbf load limit should not be exceeded on BGA packages so as to not impact solder
joint reliability after reflow. This load limit ensures that impact to the package solder
joints due to transient bend, shock, or tensile loading is minimized. The 15-lbf metric
should be used in parallel with the 689-kPa (100 psi) pressure limit as long as neither
limits are exceeded. In some cases, designing to 15 lbf will exceed the pressure
specification of 689 kPa (100 psi) and therefore should be reduced to ensure both limits
are maintained.
Moreover, the processor package substrate should not be used as a mechanical
reference or load-bearing surface for the thermal or mechanical solution.
Caution:
Datasheet
The Micro-FCBGA package incorporates land-side capacitors. The land-side capacitors
are electrically conductive so care should be taken to avoid contacting the capacitors
with other electrically conductive materials on the motherboard. Doing so may short
the capacitors and possibly damage the device or render it inactive.
51
C2
B
A
C1
52
FRONT VIEW
A
B2
Package Substrate
0.65 MAX
0.37 MAX
Underfill
A
DETAIL
SCALE 20
Die
SIDE VIEW
478 PINS
P
F2
J1
F3
2.03±0.08
0.65 MAX
J2
C
H1
1.27 BASIC
1.27 BASIC
J1
J2
W
Keying Pins
0.355
15.875 BASIC
H2
6g
15.875 BASIC
H1
0.255
31.75 BASIC
P
31.75 BASIC
G2
2.102
0.88
G1
1.862
12.4
F2
F3
C2
35.05
8.7
34.95
MAX
35.05
C1
B2
MIN
MILLIMETERS
34.95
B1
SYMBOL
BOTTOM VIEW
G1
H2
G2
B6887-01
D76563(1)
M C A B
M C
A1, A2
ø0.356
ø0.254
COMMENTS
Figure 9.
TOP VIEW
B1
Package Mechanical Specifications and Pin Information
6-MB and 3-MB on 6-MB Die Micro-FCPGA Package Drawing (Sheet 1 of 2)
Datasheet
C2
B
Datasheet
A
FRONT VIEW
TOP VIEW
ø0.65 MAX
ø0.37 MAX
Package Substrate
A
B2
A
DETAIL
SCALE 20
Underfill
Die
SIDE VIEW
øP
478 PINS
F2
J2
F3
2.03±0.08
0.65 MAX
J1
C
H1
MIN
F3
35.05
1.962
W
P
6g
Keying Pins
0.255
0.355
1.27 BASIC
1.27 BASIC
J1
J2
15.875 BASIC
H2
31.75 BASIC
15.875 BASIC
H1
31.75 BASIC
G2
G1
1.742
9.4
MAX
35.05
0.88
C2
34.95
34.95
8.7
F2
H2
MILLIMETERS
C1
B2
B1
SYMBOL
BOTTOM VIEW
G1
G2
M C A B
M C
A1, A2
ø0.356
ø0.254
COMMENTS
B6739-01
D76564(1)
Figure 10.
C1
B1
Package Mechanical Specifications and Pin Information
3-MB die Micro-FCPGA Processor Package Drawing (Sheet 1 of 2)
53
EDGE KEEP OUT
ZONE 4X
54
4X 5.00
4X 7.00
SIDE VIEW
1.5 MAX ALLOWABLE
COMPONENT HEIGHT
ø0.305±0.25
ø0.406 M C A B
ø0.254 M C
BOTTOM VIEW
6.985
13.97
1.625
6.985
13.97
1.625
B6740-01
D76564(2)
Figure 11.
TOP VIEW
CORNER KEEP OUT
ZONE 4X
4X 7.00
Package Mechanical Specifications and Pin Information
3-MB Die Micro-FCPGA Processor Package Drawing (Sheet 2 of 2)
Datasheet
C2
Datasheet
A
DETAIL B
SCALE 50
øM
FRONT VIEW
TOP VIEW
C1
B1
A
B2
W
6g
1.27 BASIC
J2
0.8
0.69
1.27 BASIC
J1
0.6
15.875 BASIC
H2
N
15.875 BASIC
H1
0.61
31.75 BASIC
M
31.75 BASIC
G2
2.207
G1
1.937
0.88
F2
F3
8.7
9.4
35.05
C1
34.95
B2
MAX
35.05
C2
34.95
MIN
MILLIMETERS
B1
SYMBOL
SIDE VIEW
ø0.203
ø0.071
B
L C A B
L
COMMENTS
479 BALLS
SEE DETAIL
J2
N
Package
Substrate
J1
H1
Die
DETAIL A
SCALE 20
Underfill
BOTTOM VIEW
G1
F2
H2
C
0.203
F3
G2
B6741-01
D93702(1)
Figure 12.
SEE DETAIL
B
Package Mechanical Specifications and Pin Information
3-MB Die Micro-FCBGA Processor Package Drawing (Sheet 1 of 2)
55
EDGE KEEP OUT
ZONE 4X
56
4X 5.00
4X 7.00
SIDE VIEW
0.55 MAX ALLOWABLE
COMPONENT HEIGHT
13.97
BOTTOM VIEW
6.985
1.625
6.985
13.97
1.625
B6742-01
D93702(2)
Figure 13.
TOP VIEW
CORNER KEEP OUT
ZONE 4X
4X 7.00
Package Mechanical Specifications and Pin Information
3-MB Die Micro-FCBGA Processor Package Drawing (Sheet 2 of 2)
Datasheet
Datasheet
:
#$%& '()"*+,,
FRONT VIEW
TOP VIEW
!"!
-. .
A
+
/
DETAIL
/
SIDE VIEW
B
3
;
4
:
0
3
;
4
:
0
DETAIL
-.
1/
8
'
6
1
8
'
6
1
ø0.39±0.02
(Solder Resist Opening)
(Metal Diameter)
BOTTOM VIEW
ø0.46±0.04
1
2
2
1/
2 .
2 .
2/ .
0
0/
1
/2
.
2
2/
/2
2/
47
//2
//2
2
4.
4..4-6
/2
/2
/2
.
2/ .
0/
/
/
/
/
34 5
/ / / / / / / / // / / /
/ / 0
ø0.14
ø0.04
L A B C
L A
544-
Figure 14.
-0. 68. 5-. .- 5656-.5 5.-. .564-.52 .- . .5 . 5.
.- 5-- 43 5- .59 665'9 .3 56 45..9 8.-05'- -0 6.56
86.-- 5- 5 .- 5656-.52
Package Mechanical Specifications and Pin Information
Intel Core 2 Duo Mobile Processor (POP and LV) Die Micro-FCBGA Processor
Package Drawing
57
58
A
/!
DETAIL
'()* +,-!&./00
:
FRONT VIEW
TOP VIEW
! "#$%&%!
SIDE VIEW
B
3
;
4
:
1
3
;
4
:
1
DETAIL
2
8
+
6
2
8
+
6
2
(Solder Resist Opening)
ø0.39±0.02
(Metal Diameter)
BOTTOM VIEW
ø0.46±0.04
2
1
2
1
2
1
47
4
446
34 5
1
ø0.14
ø0.04
L A B C
L A
544
Figure 15.
1 68 5 56565 5 5645 5 5
5 43 5 59 665+9 3 56 459 815+ 1 656
86 5 5 56565
Package Mechanical Specifications and Pin Information
Intel Core 2 Duo Mobile Processor (ULV SC and ULV DC) Die Micro-FCBGA
Processor Package Drawing
Datasheet
Package Mechanical Specifications and Pin Information
4.2
Processor Pinout and Pin List
Figure 16 and Figure 17 show the processor (SV and XE) pinout as viewed from the top
of the package. Table 16 provides the pin list, arranged numerically by pin number.
Figure 16 through Figure 18 show the top view of the LV and ULV processor package.
Table 18 lists the SFF processor ballout alphabetically by signal name. For signal
descriptions, refer to Section 4.3.
Figure 16.
1
Processor Pinout (Top Package View, Left Side)
2
3
4
5
6
7
8
9
10
11
12
13
VSS
FERR#
A20M#
VCC
VSS
VCC
VCC
VSS
VCC
VCC
A
LINT1
DPSLP#
VSS
VCC
VSS
VCC
VCC
VSS
VCC
VSS
B
VSS
LINT0
THERM
TRIP#
VSS
VCC
VCC
VSS
VCC
VCC
C
VSS
STPCLK
#
PWRGO
OD
SLP#
VSS
VCC
VCC
VSS
VCC
VSS
D
DPRSTP
#
VSS
VCC
VSS
VCC
VCC
VSS
VCC
VCC
E
VCC
VSS
VCC
VCC
VSS
VCC
VSS
A1
VSS
SMI#
B1
RSVD
INIT#
TEST7
IGNNE
#
C
D
RESET#
VSS
E
DBSY#
VSS
RSVD
RSVD
BNR#
VSS
HITM#
F
BR0#
VSS
RS[0]#
RS[1]#
VSS
RSVD
G
VSS
TRDY#
RS[2]#
VSS
BPRI#
HIT#
G
H
ADS#
REQ[1]
#
VSS
LOCK#
DEFER#
VSS
H
A[9]#
VSS
REQ[3]
#
A[3]#
VSS
VCCP
J
K
VSS
REQ[2]
#
REQ[0]
#
VSS
A[6]#
VCCP
K
L
REQ[4]#
A[13]#
VSS
A[5]#
A[4]#
VSS
L
M
ADSTB[0]
#
VSS
A[7]#
RSVD
VSS
VCCP
M
N
VSS
A[8]#
A[10]#
VSS
RSVD
VCCP
N
J
F
P
A[15]#
A[12]#
VSS
A[14]#
A[11]#
VSS
P
R
A[16]#
VSS
A[19]#
A[24]#
VSS
VCCP
R
T
VSS
RSVD
A[26]#
VSS
A[25]#
VCCP
T
U
A[23]#
A[30]#
VSS
A[21]#
A[18]#
VSS
U
V
ADSTB[1]
#
VSS
RSVD
A[31]#
VSS
VCCP
V
W
W
VSS
A[27]#
A[32]#
VSS
A[28]#
A[20]#
Y
COMP[3]
A[17]#
VSS
A[29]#
A[22]#
VSS
Y
AA
COMP[2]
VSS
A[35]#
A[33]#
VSS
TDI
VCC
VSS
VCC
VCC
VSS
VCC
VCC
A
A
AB
VSS
A[34]#
TDO
VSS
TMS
TRST#
VCC
VSS
VCC
VCC
VSS
VCC
VSS
A
B
AC
PREQ#
PRDY#
VSS
BPM[3]
#
TCK
VSS
VCC
VSS
VCC
VCC
VSS
VCC
VCC
A
C
AD
BPM[2]#
VSS
BPM[1]
#
BPM[0]
#
VSS
VID[0]
VCC
VSS
VCC
VCC
VSS
VCC
VSS
A
D
AE
VSS
VID[6]
VID[4]
VSS
VID[2]
PSI#
VSS
SENSE
VSS
VCC
VCC
VSS
VCC
VCC
A
E
AF
TEST5
VSS
VID[5]
VID[3]
VID[1]
VSS
VCC
SENSE
VSS
VCC
VCC
VSS
VCC
VSS
A
F
1
2
3
4
5
6
7
8
9
10
11
12
13
NOTES:
1.
2.
Keying option for Micro-FCPGA, A1 and B1 are de-populated.
Keying option for Micro-FCBGA, A1 is de-populated and B1 is VSS.
Datasheet
59
Package Mechanical Specifications and Pin Information
Figure 17.
14
15
Processor Pinout (Top Package View, Right Side)
16
17
18
19
20
21
22
23
24
25
26
A
VSS
VCC
VSS
VCC
VCC
VSS
VCC
BCLK[1]
BCLK[0]
VSS
THRMDA
VSS
TEST6
A
B
VCC
VCC
VSS
VCC
VCC
VSS
VCC
VSS
BSEL[0]
BSEL[1]
VSS
THRMDC
VCCA
B
C
VSS
VCC
VSS
VCC
VCC
VSS
DBR#
BSEL[2]
VSS
TEST1
TEST3
VSS
VCCA
C
D
VCC
VCC
VSS
VCC
VCC
VSS
IERR#
PROCHOT
#
RSVD
VSS
DPWR#
TEST2
VSS
D
E
VSS
VCC
VSS
VCC
VCC
VSS
VCC
VSS
D[0]#
D[7]#
VSS
D[6]#
D[2]#
E
F
VCC
VCC
VSS
VCC
VCC
VSS
VCC
DRDY#
VSS
D[4]#
D[1]#
VSS
D[13]#
F
G
VCCP
D[3]#
VSS
D[9]#
D[5]#
VSS
G
H
VSS
D[12]#
D[15]#
VSS
DINV[0]#
DSTBP[
0]#
H
DSTBN[
0]#
J
K
J
VCCP
VSS
D[11]#
D[10]#
VSS
K
VCCP
D[14]#
VSS
D[8]#
D[17]#
VSS
L
L
VSS
D[22]#
D[20]#
VSS
D[29]#
DSTBN[
1]#
M
VCCP
VSS
D[23]#
D[21]#
VSS
DSTBP[
1]#
M
N
VCCP
D[16]#
VSS
DINV[1]#
D[31]#
VSS
N
P
VSS
D[26]#
D[25]#
VSS
D[24]#
D[18]#
P
R
R
VCCP
VSS
D[19]#
D[28]#
VSS
COMP[0
]
T
VCCP
D[37]#
VSS
D[27]#
D[30]#
VSS
T
D[38]#
COMP[1
]
U
U
VSS
DINV[2]#
D[39]#
VSS
V
VCCP
VSS
D[36]#
D[34]#
VSS
D[35]#
V
W
VCCP
D[41]#
VSS
D[43]#
D[44]#
VSS
W
Y
VSS
D[32]#
D[42]#
VSS
D[40]#
DSTBN[
2]#
Y
AA
VSS
VCC
VSS
VCC
VCC
VSS
VCC
D[50]#
VSS
D[45]#
D[46]#
VSS
DSTBP[
2]#
A
A
AB
VCC
VCC
VSS
VCC
VCC
VSS
VCC
D[52]#
D[51]#
VSS
D[33]#
D[47]#
VSS
A
B
AC
VSS
VCC
VSS
VCC
VCC
VSS
DINV[3
]#
VSS
D[60]#
D[63]#
VSS
D[57]#
D[53]#
A
C
A
D
VCC
VCC
VSS
VCC
VCC
VSS
D[54]#
D[59]#
VSS
D[61]#
D[49]#
VSS
GTLREF
A
D
AE
VSS
VCC
VSS
VCC
VCC
VSS
VCC
D[58]#
D[55]#
VSS
D[48]#
DSTBN[3]
#
VSS
A
E
AF
VCC
VCC
VSS
VCC
VCC
VSS
VCC
VSS
D[62]#
D[56]#
DSTBP[3]
#
VSS
TEST4
A
F
14
15
16
17
18
19
20
21
22
23
24
25
26
60
Datasheet
Package Mechanical Specifications and Pin Information
Table 16.
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Direction
Pin Name
Pin #
Signal
Buffer
Type
A[3]#
J4
Source
Synch
Input/
Output
A[24]#
R4
Source
Synch
Input/
Output
A[4]#
L5
Source
Synch
Input/
Output
A[25]#
T5
Source
Synch
Input/
Output
A[5]#
L4
Source
Synch
Input/
Output
A[26]#
T3
Source
Synch
Input/
Output
A[6]#
K5
Source
Synch
Input/
Output
A[27]#
W2
Source
Synch
Input/
Output
A[7]#
M3
Source
Synch
Input/
Output
A[28]#
W5
Source
Synch
Input/
Output
A[8]#
N2
Source
Synch
Input/
Output
A[29]#
Y4
Source
Synch
Input/
Output
A[9]#
J1
Source
Synch
Input/
Output
A[30]#
U2
Source
Synch
Input/
Output
A[10]#
N3
Source
Synch
Input/
Output
A[31]#
V4
Source
Synch
Input/
Output
A[11]#
P5
Source
Synch
Input/
Output
A[32]#
W3
Source
Synch
Input/
Output
A[12]#
P2
Source
Synch
Input/
Output
A[33]#
AA4
Source
Synch
Input/
Output
A[13]#
L2
Source
Synch
Input/
Output
A[34]#
AB2
Source
Synch
Input/
Output
A[14]#
P4
Source
Synch
Input/
Output
A[35]#
AA3
Source
Synch
Input/
Output
Input/
Output
A6
CMOS
Input
P1
Source
Synch
A20M#
A[15]#
ADS#
H1
Source
Synch
Input/
Output
Common
Clock
Input/
Output
ADSTB[0]#
M1
Input/
Output
Input/
Output
Y2
Source
Synch
Source
Synch
ADSTB[1]#
V1
Input/
Output
U5
Input/
Output
Source
Synch
A[18]#
Source
Synch
BCLK[0]
A22
Bus Clock
A[19]#
R3
Source
Synch
Input/
Output
BCLK[1]
A21
Bus Clock
Input
BNR#
E2
Common
Clock
Input/
Output
BPM[0]#
AD4
Common
Clock
Input/
Output
BPM[1]#
AD3
Common
Clock
Output
BPM[2]#
AD1
Common
Clock
Output
BPM[3]#
AC4
Common
Clock
Input/
Output
A[16]#
A[17]#
R1
Direction
A[20]#
W6
Source
Synch
Input/
Output
A[21]#
U4
Source
Synch
Input/
Output
Y5
Source
Synch
Input/
Output
U1
Source
Synch
Input/
Output
A[22]#
A[23]#
Datasheet
Pin Name Listing
Input
61
Package Mechanical Specifications and Pin Information
Table 16.
62
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
BPRI#
G5
Common
Clock
BR0#
F1
BSEL[0]
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Direction
Input
D[14]#
K22
Source
Synch
Input/
Output
Common
Clock
Input/
Output
D[15]#
H23
Source
Synch
Input/
Output
B22
CMOS
Output
D[16]#
N22
BSEL[1]
B23
CMOS
Output
Source
Synch
Input/
Output
BSEL[2]
C21
CMOS
Output
D[17]#
K25
Source
Synch
Input/
Output
COMP[0]
R26
Power/
Other
Input/
Output
D[18]#
P26
Source
Synch
Input/
Output
COMP[1]
U26
Power/
Other
Input/
Output
D[19]#
R23
Source
Synch
Input/
Output
COMP[2]
AA1
Power/
Other
Input/
Output
D[20]#
L23
Source
Synch
Input/
Output
COMP[3]
Y1
Power/
Other
Input/
Output
D[21]#
M24
Source
Synch
Input/
Output
D[0]#
E22
Source
Synch
Input/
Output
D[22]#
L22
Source
Synch
Input/
Output
D[1]#
F24
Source
Synch
Input/
Output
D[23]#
M23
Source
Synch
Input/
Output
D[2]#
E26
Source
Synch
Input/
Output
D[24]#
P25
Source
Synch
Input/
Output
D[3]#
G22
Source
Synch
Input/
Output
D[25]#
P23
Source
Synch
Input/
Output
D[4]#
F23
Source
Synch
Input/
Output
D[26]#
P22
Source
Synch
Input/
Output
D[5]#
G25
Source
Synch
Input/
Output
D[27]#
T24
Source
Synch
Input/
Output
D[6]#
E25
Source
Synch
Input/
Output
D[28]#
R24
Source
Synch
Input/
Output
D[7]#
E23
Source
Synch
Input/
Output
D[29]#
L25
Source
Synch
Input/
Output
D[8]#
K24
Source
Synch
Input/
Output
D[30]#
T25
Source
Synch
Input/
Output
D[9]#
G24
Source
Synch
Input/
Output
D[31]#
N25
Source
Synch
Input/
Output
D[10]#
J24
Source
Synch
Input/
Output
D[32]#
Y22
Source
Synch
Input/
Output
D[11]#
J23
Source
Synch
Input/
Output
D[33]#
AB24
Source
Synch
Input/
Output
D[12]#
H22
Source
Synch
Input/
Output
D[34]#
V24
Source
Synch
Input/
Output
D[13]#
F26
Source
Synch
Input/
Output
D[35]#
V26
Source
Synch
Input/
Output
Direction
Datasheet
Package Mechanical Specifications and Pin Information
Table 16.
Pin Name
Pin #
Signal
Buffer
Type
Direction
D[36]#
V23
Source
Synch
D[37]#
T22
D[38]#
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Direction
Input/
Output
D[58]#
AE21
Source
Synch
Input/
Output
Source
Synch
Input/
Output
D[59]#
AD21
Source
Synch
Input/
Output
U25
Source
Synch
Input/
Output
D[60]#
AC22
Source
Synch
Input/
Output
D[39]#
U23
Source
Synch
Input/
Output
D[61]#
AD23
Source
Synch
Input/
Output
D[40]#
Y25
Source
Synch
Input/
Output
D[62]#
AF22
Source
Synch
Input/
Output
D[41]#
W22
Source
Synch
Input/
Output
D[63]#
AC23
Source
Synch
Input/
Output
D[42]#
Y23
Source
Synch
Input/
Output
DBR#
C20
CMOS
Output
Input/
Output
E1
W24
Source
Synch
DBSY#
D[43]#
Common
Clock
Input/
Output
Input/
Output
DEFER#
H5
Common
Clock
Input
W25
Source
Synch
Input/
Output
DINV[0]#
H25
AA23
Source
Synch
Source
Synch
Input/
Output
N24
AA24
Input/
Output
DINV[1]#
D[46]#
Source
Synch
Source
Synch
Input/
Output
Input/
Output
U22
AB25
Source
Synch
DINV[2]#
D[47]#
Source
Synch
Input/
Output
Input/
Output
DINV[3]#
AC20
AE24
Source
Synch
Source
Synch
Input/
Output
DPRSTP#
E5
CMOS
Input
D[49]#
AD24
Source
Synch
Input/
Output
DPSLP#
B5
CMOS
Input
D[50]#
AA21
Source
Synch
Input/
Output
DPWR#
D24
Common
Clock
Input/
Output
D[51]#
AB22
Source
Synch
Input/
Output
DRDY#
F21
Common
Clock
Input/
Output
D[52]#
AB21
Source
Synch
Input/
Output
DSTBN[0]#
J26
Source
Synch
Input/
Output
D[53]#
AC26
Source
Synch
Input/
Output
DSTBN[1]#
L26
Source
Synch
Input/
Output
D[54]#
AD20
Source
Synch
Input/
Output
DSTBN[2]#
Y26
Source
Synch
Input/
Output
D[55]#
AE22
Source
Synch
Input/
Output
DSTBN[3]#
AE25
Source
Synch
Input/
Output
D[56]#
AF23
Source
Synch
Input/
Output
DSTBP[0]#
H26
Source
Synch
Input/
Output
D[57]#
AC25
Source
Synch
Input/
Output
DSTBP[1]#
M26
Source
Synch
Input/
Output
D[44]#
D[45]#
D[48]#
Datasheet
Pin Name Listing
63
Package Mechanical Specifications and Pin Information
Table 16.
Pin Name
Pin #
Signal
Buffer
Type
Direction
DSTBP[2]#
AA26
Source
Synch
DSTBP[3]#
AF24
FERR#
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Input/
Output
RS[1]#
F4
Common
Clock
Input
Source
Synch
Input/
Output
RS[2]#
G3
Common
Clock
Input
A5
Open
Drain
Output
RSVD
B2
Reserved
RSVD
D2
Reserved
GTLREF
AD26
Power/
Other
RSVD
D3
Reserved
Input/
Output
D22
Reserved
G6
Common
Clock
RSVD
HIT#
RSVD
F6
Reserved
HITM#
E4
Common
Clock
Input/
Output
RSVD
M4
Reserved
RSVD
N5
Reserved
D20
Open
Drain
Output
RSVD
T2
Reserved
RSVD
V3
Reserved
SLP#
D7
CMOS
Input
SMI#
A3
CMOS
Input
IERR#
Input
IGNNE#
C4
CMOS
Input
INIT#
B3
CMOS
Input
LINT0
C6
CMOS
Input
LINT1
B4
CMOS
Input
LOCK#
H4
Common
Clock
Input/
Output
PRDY#
AC2
Common
Clock
Output
PREQ#
AC1
Common
Clock
Input
D21
Open
Drain
PROCHOT#
Input/
Output
Direction
STPCLK#
D5
CMOS
Input
TCK
AC5
CMOS
Input
TDI
AA6
CMOS
Input
TDO
AB3
Open
Drain
Output
TEST1
C23
Test
TEST2
D25
Test
TEST3
C24
Test
TEST4
AF26
Test
TEST5
AF1
Test
TEST6
A26
Test
TEST7
PSI#
AE6
CMOS
Output
PWRGOOD
D6
CMOS
Input
REQ[0]#
K3
Source
Synch
Input/
Output
C3
Test
REQ[1]#
H2
Source
Synch
Input/
Output
THERMTRIP
#
C7
Open
Drain
REQ[2]#
K2
Source
Synch
Input/
Output
THRMDA
A24
Power/
Other
REQ[3]#
J3
Source
Synch
Input/
Output
THRMDC
B25
Power/
Other
REQ[4]#
L1
Source
Synch
Input/
Output
TMS
AB5
CMOS
Input
TRDY#
G2
Input
Common
Clock
Input
C1
Common
Clock
TRST#
AB6
CMOS
Input
F3
Common
Clock
Input
VCC
A7
Power/
Other
RESET#
RS[0]#
64
Pin Name Listing
Output
Datasheet
Package Mechanical Specifications and Pin Information
Table 16.
Datasheet
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
VCC
A9
VCC
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Power/
Other
VCC
AB15
Power/
Other
A10
Power/
Other
VCC
AB17
Power/
Other
VCC
A12
Power/
Other
VCC
AB18
Power/
Other
VCC
A13
Power/
Other
VCC
AB20
Power/
Other
VCC
A15
Power/
Other
VCC
AC7
Power/
Other
VCC
A17
Power/
Other
VCC
AC9
Power/
Other
VCC
A18
Power/
Other
VCC
AC10
Power/
Other
VCC
A20
Power/
Other
VCC
AC12
Power/
Other
VCC
AA7
Power/
Other
VCC
AC13
Power/
Other
VCC
AA9
Power/
Other
VCC
AC15
Power/
Other
VCC
AA10
Power/
Other
VCC
AC17
Power/
Other
VCC
AA12
Power/
Other
VCC
AC18
Power/
Other
VCC
AA13
Power/
Other
VCC
AD7
Power/
Other
VCC
AA15
Power/
Other
VCC
AD9
Power/
Other
VCC
AA17
Power/
Other
VCC
AD10
Power/
Other
VCC
AA18
Power/
Other
VCC
AD12
Power/
Other
VCC
AA20
Power/
Other
VCC
AD14
Power/
Other
VCC
AB7
Power/
Other
VCC
AD15
Power/
Other
VCC
AB9
Power/
Other
VCC
AD17
Power/
Other
VCC
AB10
Power/
Other
VCC
AD18
Power/
Other
VCC
AB12
Power/
Other
VCC
AE9
Power/
Other
VCC
AB14
Power/
Other
VCC
AE10
Power/
Other
Direction
Direction
65
Package Mechanical Specifications and Pin Information
Table 16.
66
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
VCC
AE12
VCC
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Power/
Other
VCC
B20
Power/
Other
AE13
Power/
Other
VCC
C9
Power/
Other
VCC
AE15
Power/
Other
VCC
C10
Power/
Other
VCC
AE17
Power/
Other
VCC
C12
Power/
Other
VCC
AE18
Power/
Other
VCC
C13
Power/
Other
VCC
AE20
Power/
Other
VCC
C15
Power/
Other
VCC
AF9
Power/
Other
VCC
C17
Power/
Other
VCC
AF10
Power/
Other
VCC
C18
Power/
Other
VCC
AF12
Power/
Other
VCC
D9
Power/
Other
VCC
AF14
Power/
Other
VCC
D10
Power/
Other
VCC
AF15
Power/
Other
VCC
D12
Power/
Other
VCC
AF17
Power/
Other
VCC
D14
Power/
Other
VCC
AF18
Power/
Other
VCC
D15
Power/
Other
VCC
AF20
Power/
Other
VCC
D17
Power/
Other
VCC
B7
Power/
Other
VCC
D18
Power/
Other
VCC
B9
Power/
Other
VCC
E7
Power/
Other
VCC
B10
Power/
Other
VCC
E9
Power/
Other
VCC
B12
Power/
Other
VCC
E10
Power/
Other
VCC
B14
Power/
Other
VCC
E12
Power/
Other
VCC
B15
Power/
Other
VCC
E13
Power/
Other
VCC
B17
Power/
Other
VCC
E15
Power/
Other
VCC
B18
Power/
Other
VCC
E17
Power/
Other
Direction
Direction
Datasheet
Package Mechanical Specifications and Pin Information
Table 16.
Datasheet
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
VCC
E18
VCC
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Power/
Other
VCCP
R6
Power/
Other
E20
Power/
Other
VCCP
R21
Power/
Other
VCC
F7
Power/
Other
VCCP
T6
Power/
Other
VCC
F9
Power/
Other
VCCP
T21
Power/
Other
VCC
F10
Power/
Other
VCCP
V6
Power/
Other
VCC
F12
Power/
Other
VCCP
V21
Power/
Other
VCC
F14
Power/
Other
VCCP
W21
Power/
Other
VCC
F15
Power/
Other
VCCSENSE
AF7
Power/
Other
VCC
F17
Power/
Other
VID[0]
AD6
CMOS
Output
VID[1]
AF5
CMOS
Output
VCC
F18
Power/
Other
VID[2]
AE5
CMOS
Output
AF4
CMOS
Output
F20
Power/
Other
VID[3]
VCC
VID[4]
AE3
CMOS
Output
VCCA
B26
Power/
Other
VID[5]
AF3
CMOS
Output
VID[6]
AE2
CMOS
Output
VCCA
C26
Power/
Other
VSS
A2
Power/
Other
VCCP
G21
Power/
Other
VSS
A4
Power/
Other
VCCP
J6
Power/
Other
VSS
A8
Power/
Other
VCCP
J21
Power/
Other
VSS
A11
Power/
Other
VCCP
K6
Power/
Other
VSS
A14
Power/
Other
VCCP
K21
Power/
Other
VSS
A16
Power/
Other
VCCP
M6
Power/
Other
VSS
A19
Power/
Other
VCCP
M21
Power/
Other
VSS
A23
Power/
Other
VCCP
N6
Power/
Other
VSS
A25
Power/
Other
VCCP
N21
Power/
Other
Direction
Direction
67
Package Mechanical Specifications and Pin Information
Table 16.
68
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
VSS
AA2
VSS
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Power/
Other
VSS
AC14
Power/
Other
AA5
Power/
Other
VSS
AC16
Power/
Other
VSS
AA8
Power/
other
VSS
AC19
Power/
Other
VSS
AA11
Power/
Other
VSS
AC21
Power/
Other
VSS
AA14
Power/
Other
VSS
AC24
Power/
Other
VSS
AA16
Power/
Other
VSS
AD2
Power/
Other
VSS
AA19
Power/
Other
VSS
AD5
Power/
Other
VSS
AA22
Power/
Other
VSS
AD8
Power/
Other
VSS
AA25
Power/
Other
VSS
AD11
Power/
Other
VSS
AB1
Power/
Other
VSS
AD13
Power/
Other
VSS
AB4
Power/
Other
VSS
AD16
Power/
Other
VSS
AB8
Power/
Other
VSS
AD19
Power/
Other
VSS
AB11
Power/
Other
VSS
AD22
Power/
Other
VSS
AB13
Power/
Other
VSS
AD25
Power/
Other
VSS
AB16
Power/
Other
VSS
AE1
Power/
Other
VSS
AB19
Power/
Other
VSS
AE4
Power/
Other
VSS
AB23
Power/
Other
VSS
AE8
Power/
Other
VSS
AB26
Power/
Other
VSS
AE11
Power/
Other
VSS
AC3
Power/
Other
VSS
AE14
Power/
Other
VSS
AC6
Power/
Other
VSS
AE16
Power/
Other
VSS
AC8
Power/
Other
VSS
AE19
Power/
Other
VSS
AC11
Power/
Other
VSS
AE23
Power/
Other
Direction
Direction
Datasheet
Package Mechanical Specifications and Pin Information
Table 16.
Datasheet
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
VSS
AE26
VSS
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Power/
Other
VSS
C14
Power/
Other
AF2
Power/
Other
VSS
C16
Power/
Other
VSS
AF6
Power/
Other
VSS
C19
Power/
Other
VSS
AF8
Power/
Other
VSS
C22
Power/
Other
VSS
AF11
Power/
Other
VSS
C25
Power/
Other
VSS
AF13
Power/
Other
VSS
D1
Power/
Other
VSS
AF16
Power/
Other
VSS
D4
Power/
Other
VSS
AF19
Power/
Other
VSS
D8
Power/
Other
VSS
AF21
Power/
Other
VSS
D11
Power/
Other
VSS
AF25
Power/
Other
VSS
D13
Power/
Other
VSS
B6
Power/
Other
VSS
D16
Power/
Other
VSS
B8
Power/
Other
VSS
D19
Power/
Other
VSS
B11
Power/
Other
VSS
D23
Power/
Other
VSS
B13
Power/
Other
VSS
D26
Power/
Other
VSS
B16
Power/
Other
VSS
E3
Power/
Other
VSS
B19
Power/
Other
VSS
E6
Power/
Other
VSS
B21
Power/
Other
VSS
E8
Power/
Other
VSS
B24
Power/
Other
VSS
E11
Power/
Other
VSS
C2
Power/
Other
VSS
E14
Power/
Other
VSS
C5
Power/
Other
VSS
E16
Power/
Other
VSS
C8
Power/
Other
VSS
E19
Power/
Other
VSS
C11
Power/
Other
VSS
E21
Power/
Other
Direction
Direction
69
Package Mechanical Specifications and Pin Information
Table 16.
70
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
VSS
E24
VSS
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Power/
Other
VSS
K1
Power/
Other
F2
Power/
Other
VSS
K4
Power/
Other
VSS
F5
Power/
Other
VSS
K23
Power/
Other
VSS
F8
Power/
Other
VSS
K26
Power/
Other
VSS
F11
Power/
Other
VSS
L3
Power/
Other
VSS
F13
Power/
Other
VSS
L6
Power/
Other
VSS
F16
Power/
Other
VSS
L21
Power/
Other
VSS
F19
Power/
Other
VSS
L24
Power/
Other
VSS
F22
Power/
Other
VSS
M2
Power/
Other
VSS
F25
Power/
Other
VSS
M5
Power/
Other
VSS
G1
Power/
Other
VSS
M22
Power/
Other
VSS
G4
Power/
Other
VSS
M25
Power/
Other
VSS
G23
Power/
Other
VSS
N1
Power/
Other
VSS
G26
Power/
Other
VSS
N4
Power/
Other
VSS
H3
Power/
Other
VSS
N23
Power/
Other
VSS
H6
Power/
Other
VSS
N26
Power/
Other
VSS
H21
Power/
Other
VSS
P3
Power/
Other
VSS
H24
Power/
Other
VSS
P6
Power/
Other
VSS
J2
Power/
Other
VSS
P21
Power/
Other
VSS
J5
Power/
Other
VSS
P24
Power/
Other
VSS
J22
Power/
Other
VSS
R2
Power/
Other
VSS
J25
Power/
Other
VSS
R5
Power/
Other
Direction
Direction
Datasheet
Package Mechanical Specifications and Pin Information
Table 16.
Datasheet
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
VSS
R22
VSS
Table 16.
Pin Name Listing
Pin Name
Pin #
Signal
Buffer
Type
Power/
Other
VSS
Y21
Power/
Other
R25
Power/
Other
VSS
Y24
Power/
Other
VSS
T1
Power/
Other
VSSSENSE
AE7
Power/
Other
VSS
T4
Power/
Other
VSS
T23
Power/
Other
VSS
T26
Power/
Other
VSS
U3
Power/
Other
VSS
U6
Power/
Other
VSS
U21
Power/
Other
VSS
U24
Power/
Other
VSS
V2
Power/
Other
VSS
V5
Power/
Other
VSS
V22
Power/
Other
VSS
V25
Power/
Other
VSS
W1
Power/
Other
VSS
W4
Power/
Other
VSS
W23
Power/
Other
VSS
W26
Power/
Other
VSS
Y3
Power/
Other
VSS
Y6
Power/
Other
Direction
Direction
Output
71
Package Mechanical Specifications and Pin Information
Table 17.
72
Table 17.
Pin # Listing
Pin #
Pin Name
Signal Buffer
Type
Directi
on
A2
VSS
Power/Other
A3
SMI#
CMOS
A4
VSS
Power/Other
A5
FERR#
Open Drain
Output
A6
A20M#
CMOS
Input
A7
VCC
Power/Other
A8
VSS
Power/Other
A9
VCC
Power/Other
A10
VCC
Power/Other
Input
Pin # Listing
Pin #
Pin Name
Signal Buffer
Type
AA13
VCC
Power/Other
AA14
VSS
Power/Other
AA15
VCC
Power/Other
AA16
VSS
Power/Other
AA17
VCC
Power/Other
AA18
VCC
Power/Other
Directi
on
AA19
VSS
Power/Other
AA20
VCC
Power/Other
AA21
D[50]#
Source Synch
AA22
VSS
Power/Other
AA23
D[45]#
Source Synch
Input/
Output
AA24
D[46]#
Source Synch
Input/
Output
Input/
Output
A11
VSS
Power/Other
A12
VCC
Power/Other
A13
VCC
Power/Other
A14
VSS
Power/Other
A15
VCC
Power/Other
A16
VSS
Power/Other
AA25
VSS
Power/Other
A17
VCC
Power/Other
AA26
Source Synch
A18
VCC
Power/Other
DSTBP[2]
#
A19
VSS
Power/Other
AB1
VSS
Power/Other
A20
VCC
Power/Other
AB2
A[34]#
Source Synch
Input/
Output
A21
BCLK[1]
Bus Clock
Input
AB3
TDO
Open Drain
Output
A22
BCLK[0]
Bus Clock
Input
AB4
VSS
Power/Other
A23
VSS
Power/Other
AB5
TMS
CMOS
Input
A24
THRMDA
Power/Other
AB6
TRST#
CMOS
Input
A25
VSS
Power/Other
AB7
VCC
Power/Other
A26
TEST6
Test
AA1
COMP[2]
Power/Other
AA2
VSS
Power/Other
AA3
A[35]#
Source Synch
AA4
A[33]#
Source Synch
AA5
VSS
Power/Other
Input/
Output
Input/
Output
Input/
Output
Input
AB8
VSS
Power/Other
AB9
VCC
Power/Other
AB10
VCC
Power/Other
AB11
VSS
Power/Other
AB12
VCC
Power/Other
AB13
VSS
Power/Other
AB14
VCC
Power/Other
AB15
VCC
Power/Other
AA6
TDI
CMOS
AB16
VSS
Power/Other
AA7
VCC
Power/Other
AB17
VCC
Power/Other
AA8
VSS
Power/other
AB18
VCC
Power/Other
AA9
VCC
Power/Other
AB19
VSS
Power/Other
AA10
VCC
Power/Other
AB20
VCC
Power/Other
AA11
VSS
Power/Other
AA12
VCC
Power/Other
AB21
D[52]#
Source Synch
Input/
Output
Input/
Output
Datasheet
Package Mechanical Specifications and Pin Information
Table 17.
Table 17.
Pin #
Pin Name
Signal Buffer
Type
Directi
on
AB22
D[51]#
Source Synch
AB23
VSS
Power/Other
AB24
D[33]#
Pin # Listing
Pin #
Pin Name
Signal Buffer
Type
Directi
on
Input/
Output
AD3
BPM[1]#
Common Clock
Output
AD4
BPM[0]#
Common Clock
Input/
Output
Source Synch
Input/
Output
AD5
VSS
Power/Other
AD6
VID[0]
CMOS
Input/
Output
AD7
VCC
Power/Other
AB25
D[47]#
Source Synch
AB26
VSS
Power/Other
AC1
PREQ#
Common Clock
Input
AC2
PRDY#
Common Clock
Output
AC3
VSS
Power/Other
AC4
BPM[3]#
Common Clock
Input/
Output
AC5
TCK
CMOS
Input
AD8
VSS
Power/Other
AD9
VCC
Power/Other
AD10
VCC
Power/Other
AD11
VSS
Power/Other
AD12
VCC
Power/Other
AD13
VSS
Power/Other
AD14
VCC
Power/Other
VCC
Power/Other
AC6
VSS
Power/Other
AD15
AC7
VCC
Power/Other
AD16
VSS
Power/Other
VCC
Power/Other
AC8
VSS
Power/Other
AD17
AC9
VCC
Power/Other
AD18
VCC
Power/Other
VSS
Power/Other
Output
AC10
VCC
Power/Other
AD19
AC11
VSS
Power/Other
AD20
D[54]#
Source Synch
AC12
VCC
Power/Other
Input/
Output
AC13
VCC
Power/Other
AD21
D[59]#
Source Synch
Input/
Output
AD22
VSS
Power/Other
AD23
D[61]#
Source Synch
Input/
Output
AD24
D[49]#
Source Synch
Input/
Output
AD25
VSS
Power/Other
AD26
GTLREF
Power/Other
AE1
VSS
Power/Other
AE2
VID[6]
CMOS
Output
AE3
VID[4]
CMOS
Output
AE4
VSS
Power/Other
AE5
VID[2]
CMOS
Output
AC14
VSS
Power/Other
AC15
VCC
Power/Other
AC16
VSS
Power/Other
AC17
VCC
Power/Other
AC18
VCC
Power/Other
AC19
VSS
Power/Other
AC20
DINV[3]#
Source Synch
AC21
VSS
Power/Other
AC22
73
Pin # Listing
D[60]#
Input/
Output
Source Synch
Input/
Output
Input/
Output
AC23
D[63]#
Source Synch
AC24
VSS
Power/Other
AC25
D[57]#
Source Synch
Input/
Output
Input
AE6
PSI#
CMOS
Output
AE7
VSSSENSE
Power/Other
Output
AE8
VSS
Power/Other
AE9
VCC
Power/Other
AC26
D[53]#
Source Synch
Input/
Output
AE10
VCC
Power/Other
AD1
BPM[2]#
Common Clock
Output
AE11
VSS
Power/Other
AD2
VSS
Power/Other
AE12
VCC
Power/Other
Datasheet
Package Mechanical Specifications and Pin Information
Table 17.
Pin #
Pin Name
Signal Buffer
Type
AE13
VCC
Power/Other
AE14
VSS
Power/Other
AE15
VCC
Power/Other
Table 17.
Directi
on
Pin # Listing
Pin #
Pin Name
Signal Buffer
Type
Directi
on
AF22
D[62]#
Source Synch
Input/
Output
AF23
D[56]#
Source Synch
Input/
Output
Input/
Output
AE16
VSS
Power/Other
AE17
VCC
Power/Other
AF24
DSTBP[3]
#
Source Synch
AE18
VCC
Power/Other
AF25
VSS
Power/Other
AE19
VSS
Power/Other
AF26
TEST4
Test
AE20
VCC
Power/Other
B2
RSVD
Reserved
AE21
D[58]#
Source Synch
Input/
Output
B3
INIT#
CMOS
Input
Input/
Output
B4
LINT1
CMOS
Input
B5
DPSLP#
CMOS
Input
B6
VSS
Power/Other
B7
VCC
Power/Other
B8
VSS
Power/Other
B9
VCC
Power/Other
B10
VCC
Power/Other
AE22
Datasheet
Pin # Listing
D[55]#
Source Synch
AE23
VSS
Power/Other
AE24
D[48]#
Source Synch
Input/
Output
AE25
DSTBN[3]
#
Source Synch
Input/
Output
AE26
VSS
Power/Other
AF1
TEST5
Test
AF2
VSS
Power/Other
AF3
VID[5]
CMOS
Output
AF4
VID[3]
CMOS
Output
AF5
VID[1]
CMOS
Output
AF6
VSS
B11
VSS
Power/Other
B12
VCC
Power/Other
B13
VSS
Power/Other
B14
VCC
Power/Other
B15
VCC
Power/Other
B16
VSS
Power/Other
Power/Other
B17
VCC
Power/Other
AF7
VCCSENS
E
Power/Other
B18
VCC
Power/Other
AF8
VSS
Power/Other
AF9
VCC
Power/Other
AF10
VCC
Power/Other
AF11
VSS
Power/Other
AF12
VCC
Power/Other
AF13
VSS
Power/Other
AF14
VCC
Power/Other
AF15
VCC
Power/Other
AF16
VSS
Power/Other
AF17
VCC
Power/Other
AF18
VCC
Power/Other
AF19
VSS
Power/Other
AF20
VCC
Power/Other
AF21
VSS
Power/Other
B19
VSS
Power/Other
B20
VCC
Power/Other
B21
VSS
Power/Other
B22
BSEL[0]
CMOS
Output
B23
BSEL[1]
CMOS
Output
B24
VSS
Power/Other
B25
THRMDC
Power/Other
B26
VCCA
Power/Other
C1
RESET#
Common Clock
C2
VSS
Power/Other
Input
C3
TEST7
Test
C4
IGNNE#
CMOS
C5
VSS
Power/Other
C6
LINT0
CMOS
Input
C7
THERMTRI
P#
Open Drain
Output
Input
74
Package Mechanical Specifications and Pin Information
Table 17.
Datasheet
Pin # Listing
Pin #
Pin Name
Signal Buffer
Type
C8
VSS
Power/Other
Table 17.
Directi
on
Pin # Listing
Pin #
Pin Name
Signal Buffer
Type
Directi
on
D21
PROCHOT
#
Open Drain
Input/
Output
D22
RSVD
Reserved
C9
VCC
Power/Other
C10
VCC
Power/Other
C11
VSS
Power/Other
D23
VSS
Power/Other
C12
VCC
Power/Other
D24
DPWR#
Common Clock
C13
VCC
Power/Other
C14
VSS
Power/Other
D25
TEST2
Test
C15
VCC
Power/Other
D26
VSS
Power/Other
C16
VSS
Power/Other
E1
DBSY#
Common Clock
Input/
Output
C17
VCC
Power/Other
C18
VCC
Power/Other
E2
BNR#
Common Clock
Input/
Output
C19
VSS
Power/Other
E3
VSS
Power/Other
C20
DBR#
CMOS
Output
E4
HITM#
Common Clock
C21
BSEL[2]
CMOS
Output
Input/
Output
C22
VSS
Power/Other
E5
DPRSTP#
CMOS
Input
C23
TEST1
Test
E6
VSS
Power/Other
C24
TEST3
Test
E7
VCC
Power/Other
C25
VSS
Power/Other
E8
VSS
Power/Other
C26
VCCA
Power/Other
D1
VSS
Power/Other
D2
RSVD
Reserved
D3
RSVD
Reserved
D4
VSS
Power/Other
D5
STPCLK#
CMOS
Input
D6
PWRGOOD
CMOS
Input
D7
SLP#
CMOS
Input
D8
VSS
Power/Other
D9
VCC
Power/Other
D10
VCC
Power/Other
D11
VSS
Power/Other
D12
VCC
Power/Other
D13
VSS
Power/Other
D14
VCC
Power/Other
D15
VCC
Power/Other
D16
VSS
Power/Other
D17
VCC
Power/Other
D18
VCC
Power/Other
D19
VSS
Power/Other
D20
IERR#
Open Drain
E9
VCC
Power/Other
E10
VCC
Power/Other
E11
VSS
Power/Other
E12
VCC
Power/Other
E13
VCC
Power/Other
E14
VSS
Power/Other
E15
VCC
Power/Other
E16
VSS
Power/Other
E17
VCC
Power/Other
E18
VCC
Power/Other
Input/
Output
E19
VSS
Power/Other
E20
VCC
Power/Other
E21
VSS
Power/Other
E22
D[0]#
Source Synch
Input/
Output
E23
D[7]#
Source Synch
Input/
Output
E24
VSS
Power/Other
E25
D[6]#
Source Synch
Input/
Output
E26
D[2]#
Source Synch
Input/
Output
F1
BR0#
Common Clock
Input/
Output
Output
75
Package Mechanical Specifications and Pin Information
Table 17.
Pin #
Pin Name
Signal Buffer
Type
Table 17.
Directi
on
Pin # Listing
Pin #
Pin Name
Signal Buffer
Type
Directi
on
G25
D[5]#
Source Synch
Input/
Output
G26
VSS
Power/Other
H1
ADS#
Common Clock
Input/
Output
Input/
Output
F2
VSS
Power/Other
F3
RS[0]#
Common Clock
Input
F4
RS[1]#
Common Clock
Input
F5
VSS
Power/Other
F6
RSVD
Reserved
F7
VCC
Power/Other
H2
REQ[1]#
Source Synch
H3
VSS
Power/Other
H4
LOCK#
Common Clock
Input/
Output
Input
F8
VSS
Power/Other
F9
VCC
Power/Other
F10
VCC
Power/Other
F11
VSS
Power/Other
H5
DEFER#
Common Clock
VSS
Power/Other
F12
VCC
Power/Other
H6
F13
VSS
Power/Other
H21
VSS
Power/Other
F14
VCC
Power/Other
H22
D[12]#
Source Synch
F15
VCC
Power/Other
Input/
Output
F16
VSS
Power/Other
H23
D[15]#
Source Synch
Input/
Output
F17
VCC
Power/Other
H24
VSS
Power/Other
F18
VCC
Power/Other
F19
VSS
Power/Other
H25
DINV[0]#
Source Synch
Input/
Output
F20
VCC
Power/Other
H26
DSTBP[0]
#
Source Synch
Input/
Output
J1
A[9]#
Source Synch
Input/
Output
J2
VSS
Power/Other
J3
REQ[3]#
Source Synch
Input/
Output
J4
A[3]#
Source Synch
Input/
Output
J5
VSS
Power/Other
F21
DRDY#
Common Clock
F22
VSS
Power/Other
F23
D[4]#
Source Synch
F24
76
Pin # Listing
D[1]#
Source Synch
F25
VSS
Power/Other
F26
D[13]#
Source Synch
G1
VSS
Power/Other
Input/
Output
Input/
Output
Input/
Output
Input/
Output
G2
TRDY#
Common Clock
Input
G3
RS[2]#
Common Clock
Input
J6
VCCP
Power/Other
J21
VCCP
Power/Other
J22
VSS
Power/Other
J23
D[11]#
Source Synch
Input/
Output
Input/
Output
G4
VSS
Power/Other
G5
BPRI#
Common Clock
Input
J24
D[10]#
Source Synch
G6
HIT#
Common Clock
Input/
Output
J25
VSS
Power/Other
G21
VCCP
Power/Other
J26
DSTBN[0]
#
Source Synch
G22
D[3]#
Source Synch
K1
VSS
Power/Other
G23
VSS
Power/Other
K2
REQ[2]#
Source Synch
G24
D[9]#
Source Synch
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Datasheet
Package Mechanical Specifications and Pin Information
Table 17.
Table 17.
Pin #
Pin Name
Signal Buffer
Type
Directi
on
K3
REQ[0]#
Source Synch
Input/
Output
K4
VSS
Power/Other
K5
A[6]#
Source Synch
K6
VCCP
Power/Other
K21
VCCP
Power/Other
K22
D[14]#
Source Synch
K23
VSS
Power/Other
K24
D[8]#
Input/
Output
Input/
Output
Source Synch
Input/
Output
Input/
Output
K25
D[17]#
Source Synch
K26
VSS
Power/Other
L1
REQ[4]#
Source Synch
Input/
Output
L2
A[13]#
Source Synch
Input/
Output
L3
VSS
Power/Other
L4
A[5]#
Source Synch
Input/
Output
L5
A[4]#
Source Synch
Input/
Output
L6
VSS
Power/Other
L21
VSS
Power/Other
L22
Datasheet
Pin # Listing
D[22]#
Source Synch
Input/
Output
Input/
Output
L23
D[20]#
Source Synch
L24
VSS
Power/Other
Source Synch
Input/
Output
Source Synch
Input/
Output
M1
ADSTB[0]
#
Source Synch
Input/
Output
M2
VSS
Power/Other
M3
A[7]#
Source Synch
M4
RSVD
Reserved
M5
VSS
Power/Other
M6
VCCP
Power/Other
M21
VCCP
Power/Other
L25
D[29]#
L26
DSTBN[1]
#
Input/
Output
Pin # Listing
Pin #
Pin Name
Signal Buffer
Type
M22
VSS
Power/Other
M23
D[23]#
Source Synch
Input/
Output
M24
D[21]#
Source Synch
Input/
Output
M25
VSS
Power/Other
M26
DSTBP[1]
#
Source Synch
N1
VSS
Power/Other
N2
A[8]#
Source Synch
Input/
Output
N3
A[10]#
Source Synch
Input/
Output
N4
VSS
Power/Other
N5
RSVD
Reserved
N6
VCCP
Power/Other
N21
VCCP
Power/Other
N22
D[16]#
Source Synch
Directi
on
Input/
Output
Input/
Output
N23
VSS
Power/Other
N24
DINV[1]#
Source Synch
Input/
Output
N25
D[31]#
Source Synch
Input/
Output
N26
VSS
Power/Other
P1
A[15]#
Source Synch
Input/
Output
P2
A[12]#
Source Synch
Input/
Output
P3
VSS
Power/Other
P4
A[14]#
Source Synch
Input/
Output
P5
A[11]#
Source Synch
Input/
Output
P6
VSS
Power/Other
P21
VSS
Power/Other
P22
D[26]#
Source Synch
Input/
Output
P23
D[25]#
Source Synch
Input/
Output
P24
VSS
Power/Other
P25
D[24]#
Source Synch
Input/
Output
77
Package Mechanical Specifications and Pin Information
Table 17.
Table 17.
Pin # Listing
Pin #
Pin Name
Signal Buffer
Type
Directi
on
Pin #
Pin Name
Signal Buffer
Type
Directi
on
P26
D[18]#
Source Synch
Input/
Output
U5
A[18]#
Source Synch
Input/
Output
R1
A[16]#
Source Synch
Input/
Output
R2
VSS
Power/Other
R3
A[19]#
Source Synch
Input/
Output
Input/
Output
U6
VSS
Power/Other
U21
VSS
Power/Other
U22
DINV[2]#
Source Synch
Input/
Output
U23
D[39]#
Source Synch
Input/
Output
U24
VSS
Power/Other
U25
D[38]#
Source Synch
Input/
Output
U26
COMP[1]
Power/Other
Input/
Output
V1
ADSTB[1]
#
Source Synch
Input/
Output
V2
VSS
Power/Other
V3
RSVD
Reserved
V4
A[31]#
Source Synch
V5
VSS
Power/Other
R4
A[24]#
Source Synch
R5
VSS
Power/Other
R6
VCCP
Power/Other
R21
VCCP
Power/Other
R22
VSS
Power/Other
R23
D[19]#
Source Synch
Input/
Output
R24
D[28]#
Source Synch
Input/
Output
R25
VSS
Power/Other
R26
COMP[0]
Power/Other
T1
VSS
Power/Other
V6
VCCP
Power/Other
T2
RSVD
Reserved
V21
VCCP
Power/Other
T3
A[26]#
Source Synch
V22
VSS
Power/Other
T4
VSS
Power/Other
V23
D[36]#
Source Synch
Input/
Output
T5
A[25]#
Source Synch
V24
D[34]#
Source Synch
Input/
Output
T6
VCCP
Power/Other
V25
VSS
Power/Other
T21
VCCP
Power/Other
V26
D[35]#
Source Synch
W1
VSS
Power/Other
W2
A[27]#
Source Synch
Input/
Output
W3
A[32]#
Source Synch
Input/
Output
W4
VSS
Power/Other
W5
A[28]#
Source Synch
Input/
Output
W6
A[20]#
Source Synch
Input/
Output
W21
VCCP
Power/Other
W22
D[41]#
Source Synch
W23
VSS
Power/Other
T22
D[37]#
Source Synch
T23
VSS
Power/Other
T24
D[27]#
Source Synch
T25
D[30]#
Source Synch
T26
VSS
Power/Other
U1
78
Pin # Listing
A[23]#
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Source Synch
Input/
Output
Input/
Output
U2
A[30]#
Source Synch
U3
VSS
Power/Other
U4
A[21]#
Source Synch
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Datasheet
Package Mechanical Specifications and Pin Information
Table 17.
Datasheet
Pin # Listing
Pin #
Pin Name
Signal Buffer
Type
Directi
on
W24
D[43]#
Source Synch
Input/
Output
W25
D[44]#
Source Synch
Input/
Output
W26
VSS
Power/Other
Y1
COMP[3]
Power/Other
Input/
Output
Y2
A[17]#
Source Synch
Input/
Output
Y3
VSS
Power/Other
Y4
A[29]#
Source Synch
Input/
Output
Y5
A[22]#
Source Synch
Input/
Output
Y6
VSS
Power/Other
Y21
VSS
Power/Other
Y22
D[32]#
Source Synch
Input/
Output
Y23
D[42]#
Source Synch
Input/
Output
Y24
VSS
Power/Other
Y25
D[40]#
Source Synch
Input/
Output
Y26
DSTBN[2]
#
Source Synch
Input/
Output
79
Package Mechanical Specifications and Pin Information
Figure 18.
BD
Intel Core 2 Duo Mobile Processor in SFF Package Top View Upper Left Side
BC
BB
1
2
VSS
VSS
5
6
VSS
9
10
PSI#
12
VSS
VCC
17
18
80
VCC
VSS
VCC
VCC
VCC
VSS
VCC
VCC
VSS
VCC
VSS
VCC
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VCCP
VSS
VSS
VCC
VCCP
VSS
VCC
VCC
VCC
VSS
VCC
VCCP
VSS
VSS
VCCP
VSS
VCCP
VSS
VSS
VSS
VCCP
VCCP
VCC
VCCP
VSS
VCCP
VCCP
VCC
VCCP
VCCP
VSS
VSS
VSS
VSS
VCCP
VCCP
VSS
VCCP
VSS
VCCP
VSS
VCC
VCC
VCC
VCC
VCC
VCCP
VCCP
VCCP
VCCP
VCCP
VSS
VSS
VSS
VCC
VCC
VCC
VCCP
A[10]#
VSS
VSS
VSS
VSS
A[12]#
A[14]#
VCCP
VCCP
VCCP
VSS
VCCP
VSS
VSS
VCC
VCCP
VSS
VCC
VCC
VSS
VCC
VCC
VCCP
VSS
VCCP
VCCP
VSS
VSS
VCC
VCCP
VSS
VCC
VCC
VSS
VCC
VCC
VCCP
VCCP
VSS
VCCP
VSS
VSS
VCC
VCCP
VSS
VCC
VCC
VSS
VCC
VCC
VCCP
VSS
VSS
VSS
VSS
VSS
VCC
VSS
VSS
VCC
VCC
21
22
VCC
VSS
PRDY#
VSS
VSS
VSS
19
20
VSS
VSS
VCC
VSS
TEST5
VSS
VSSSE
NSE
15
16
VID[2]
VCCS
ENSE
13
14
VSS
AC
A[16]#
VSS
VSS
VSS
AD
A[11]#
A[24]#
RSVD0
3
VCCP
AE
COMP[
2]
VSS
VSS
VSS
AF
COMP[
3]
A[26]#
A[25]#
VCCP
AG
A[19]#
VSS
VSS
VSS
AH
A[23]#
A[18]#
RSVD0
4
VCCP
AJ
A[30]#
VSS
VSS
VSS
AK
A[21]#
A[27]#
ADSTB
[1]#
VCCP
AL
A[31]#
VSS
VSS
VSS
AM
A[32]#
A[28]#
A[29]#
VSS
AN
A[17]#
VSS
VSS
TRST#
AP
A[34]#
A[20]#
A[33]#
TDI
AR
A[35]#
VSS
VSS
BPM[0]
#
VID[3]
VSS
11
VSS
AT
A[22]#
TCK
TMS
BPM[1]
#
AU
TDO
VSS
BPM[2]
#
VID[1]
AV
PREQ#
VID[6]
VSS
VID[0]
AW
VSS
VSS
VID[5]
VID[4]
7
8
AY
BPM[3]
#
VSS
3
4
BA
VSS
VSS
VCC
VSS
VCC
VSS
VCC
Datasheet
Package Mechanical Specifications and Pin Information
Figure 19.
Intel Core 2 Duo Mobile Processor in SFF Package Top View Upper Right Side
AB AA
1
2
VSS
6
7
8
VSS
9
10
VCCP
VCCP
11
12
16
20
VCC
VCC
VCC
VSS
VCC
Datasheet
VCC
VCC
VSS
VCC
VCC
VCC
VCC
VCC
VCC
VSS
VCC
VCC
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VSS
VSS
VSS
VCCP
VCC
VCC
VCCP
VSS
VSS
VSS
VCC
VCCP
VCC
VCC
VSS
VCCP
VCCP
VCC
VCC
VCC
VCCP
VSS
VSS
VSS
VSS
VCC
VCC
VSS
THER
MTRIP
#
VSS
VCCP
VSS
VSS
VSS
VSS
VCC
VCC
LINT0
VCCP
VCCP
VSS
DPSLP
#
SLP#
VCCP
VCCP
VSS
INIT#
IGNNE
#
VSS
A20M#
VSS
VCCP
VSS
VSS
VSS
VSS
VCC
VCC
VCC
VCC
VCCP
A
VSS
VSS
STPCL
K#
VCCP
B
LINT1
PWRG
OOD
VCCP
VCCP
VSS
VSS
VSS
VSS
VCCP
VCC
VCC
VCCP
FERR#
VSS
VSS
C
VSS
SMI#
VSS
VCCP
VCCP
VSS
VSS
VSS
VSS
VCC
VCC
VCCP
VSS
VCCP
RSVD0
5
VCCP
VCCP
VSS
VSS
VSS
VCCP
VCCP
VCC
VSS
VSS
DPRST
P#
RSVD0
7
VSS
VCCP
VCCP
VCCP
VSS
VSS
VCCP
VSS
VCCP
VCCP
VCCP
VCCP
VSS
VSS
VCC
VCCP
VCCP
VCC
VSS
VCCP
VCCP
VSS
21
22
VSS
VCCP
19
VCCP
VCCP
VSS
VSS
D
VSS
RSVD0
6
RESET
#
DBR#
E
VSS
HITM#
RS[1]#
VSS
F
VSS
BNR#
VCCP
G
VSS
HIT#
RS[2]#
VSS
H
VSS
BPRI#
VCCP
J
DBSY#
VSS
DEFER
#
VSS
K
RS[0]#
ADS#
VSS
VSS
L
TRDY#
VSS
VCCP
VCCP
VCCP
VCCP
17
18
VSS
VCCP
15
VSS
VCCP
VCCP
13
14
VSS
VSS
M
BR0#
REQ[3]
#
REQ[1]
#
VCCP
N
LOCK#
A[3]#
A[6]#
VSS
P
VSS
VSS
VCCP
R
REQ[0]
#
A[9]#
A[4]#
VSS
T
VSS
REQ[4]
#
VCCP
U
REQ[2]
#
VSS
A[13]#
VSS
V
RSVD0
1
ADSTB
[0]#
A[8]#
5
W
A[5]#
RSVD0
2
A[15]#
3
4
Y
A[7]#
VSS
VCC
VSS
VCC
VSS
VCC
81
Package Mechanical Specifications and Pin Information
Figure 20.
Intel Core 2 Duo Mobile Processor in SFF Package Top View Lower Left Side
BD BC BB BA AY AW AV
23
24
VSS
VCC
25
26
VCC
VCC
32
VCC
33
34
38
VSS
41
42
43
44
82
VSS
VSS
D[59]#
VSS
D[50]#
VSS
VSS
D[42]#
VSS
VSS
VSS
DSTBP
[2]#
D[40]#
VSS
D[26]#
TEST4
VSS
D[27]#
VSS
COMP[
0]
D[44]#
D[39]#
VSS
D[35]#
VSS
VCCP
VSS
D[37]#
D[36]#
DSTBN
[2]#
VSS
VCCP
D[34]#
VCCP
VCCP
VSS
DINV[2
]#
D[47]#
D[41]#
D[32]#
D[43]#
VCCP
VCCP
VSS
VCC
VSS
VCCP
VSS
VSS
VCC
VSS
VSS
VCCP
VCC
VCC
VCCP
VCCP
VSS
D[46]#
D[33]#
D[49]#
VSS
D[45]#
VSS
VCCP
VSS
VSS
VCC
VCCP
VCCP
VSS
D[53]#
D[63]#
VSS
VCCP
D[57]#
VSS
VSS
VSS
VCC
VSS
VSS
VCC
VCC
VCC
VSS
VCC
VCC
VSS
VCC
VCCP
VCCP
VSS
D[51]#
GTLRE
F
VSS
VSS
VCC
VSS
VCCP
VSS
VCC
VCCP
VSS
VSS
D[52]#
VSS
VSS
D[48]#
VCC
VCC
VSS
VSS
VSS
D[60]#
VSS
VSS
VSS
DSTBN
[3]#
D[61]#
VCC
VSS
VSS
VSS
VSS
D[38]#
AC
VSS
VCC
VCC
VCC
AD
VSS
VSS
VSS
AE
VSS
VSS
VCC
VCC
AF
VCC
VCC
VCC
VCC
VCC
VCC
VSS
DSTBP
[3]#
VSS
VSS
VSS
D[56]#
D[55]#
VCC
VCC
VSS
VSS
VSS
VSS
VCC
VCC
VCC
AH AG
VSS
VSS
VSS
VSS
VCC
VSS
D[54]#
VCC
VCC
VCC
VCC
AJ
VSS
VCC
VSS
VSS
VSS
VSS
VSS
D[62]#
DINV[3
]#
VSS
VSS
VSS
VCC
VCC
VCC
THRM
DA
D[58]#
39
40
VSS
VSS
37
VCC
VCC
THRM
DC
35
36
VCC
VCC
VCC
AK
VSS
VSS
VSS
VSS
AN AM AL
VSS
VCC
VCC
VCC
AP
VSS
VSS
VSS
AR
VSS
VCC
VCC
VCC
AT
VSS
VSS
VSS
VSS
VCC
VCC
VCC
AU
VSS
VSS
VSS
VSS
31
VCC
VCC
VCC
VSS
VSS
VSS
29
30
VCC
VSS
27
28
VSS
TEST6
COMP[
1]
Datasheet
Package Mechanical Specifications and Pin Information
Figure 21.
AB
23
24
VCC
VCC
32
VSS
VCC
33
34
VCC
VCCP
41
42
D[24]#
VSS
43
44
D[21]#
VSS
DSTBP
[1]#
D[28]#
D[19]#
Datasheet
D[23]#
VSS
D[30]#
D[20]#
VSS
DSTBN
[1]#
D[18]#
D[31]#
VSS
D[10]#
DINV[1
]#
VSS
D[8]#
D[15]#
D[14]#
D[4]#
VSS
D[9]#
VSS
D[13]#
D[5]#
BSEL[2
]
VSS
IERR#
DPWR
#
VSS
D[2]#
VSS
BSEL[0
]
VSS
D[7]#
D[1]#
VSS
TEST2
VSS
BCLK[
0]
BSEL[1
]
PROC
HOT#
D[0]#
VSS
D[3]#
VSS
DRDY#
VCCP
VCCA
BCLK[
1]
TEST1
D[6]#
DSTBP
[0]#
VCCP
VCCP
VSS
VSS
VCCP
VCCA
VCCP
VSS
DSTBN
[0]#
VSS
D[22]#
D[16]#
VCCP
D[12]#
VSS
VCCP
VSS
VCCP
VCCP
VSS
VCC
VCCP
VCCP
VCCP
VSS
VSS
VCC
VSS
VCC
VCC
VCC
VSS
VCCP
VCCP
VSS
DINV[0
]#
VCC
VCCP
VSS
VSS
VCC
VSS
VCCP
VCCP
VSS
D[11]#
VCC
VSS
VCCP
VSS
VCC
VSS
VCCP
VCCP
VSS
D[17]#
VCC
VCCP
VSS
VSS
VCC
VSS
VCCP
VCCP
VSS
D[29]#
VCC
VSS
VCCP
VSS
VCC
VSS
VCCP
VCCP
VSS
D[25]#
VCC
VCCP
VSS
VSS
VCC
VSS
VCCP
VCCP
39
40
VCC
VSS
VCCP
VSS
VCC
VSS
VCCP
37
38
VCC
VSS
35
36
VSS
VSS
VCC
VSS
VSS
A
VSS
VSS
VCC
VCC
B
VCC
VCC
VSS
VSS
C
VSS
VSS
VCC
VCC
D
VCC
VCC
VSS
VSS
E
VSS
VSS
VCC
VCC
F
VCC
VCC
VSS
VSS
G
VSS
VSS
VCC
VCC
H
VCC
VCC
VSS
VSS
J
VSS
VSS
VCC
VCC
K
VCC
VCC
VSS
VSS
L
VSS
VSS
VCC
VCC
M
VCC
VCC
VSS
VSS
N
VSS
VSS
VCC
VCC
P
VCC
VCC
VSS
VSS
R
VSS
VSS
VCC
VCC
T
VCC
VCC
VSS
VSS
U
VSS
VSS
VCC
VCC
V
VCC
VCC
VSS
31
W
VSS
VSS
29
30
Y
VCC
VCC
27
28
AA
VSS
25
26
Intel Core 2 Duo Mobile Processor in SFF Package Top View Lower Right Side
VSS
VSS
TEST3
VSS
83
Package Mechanical Specifications and Pin Information
Table 18.Intel Core 2 Duo Mobile Processor in SFF Package Listing by Ball Name
84
Signal
Name
Ball
Number
Signal Name
Ball
Number
Signal
Name
Ball
Number
A[3]#
P2
BCLK[0]
AN5
D[20]#
R41
A[4]#
V4
BCLK[1]
A35
D[21]#
W41
A[5]#
W1
BNR#
C35
D[22]#
N43
A[6]#
T4
BPM[0]#
J5
D[23]#
U41
A[7]#
AA1
BPM[1]#
AY8
D[24]#
AA41
A[8]#
AB4
BPM[2]#
BA7
D[25]#
AB40
A[9]#
T2
BPM[3]#
BA5
D[26]#
AD40
A[10]#
AC5
BPRI#
AY2
D[27]#
AC41
A[11]#
AD2
BR0#
L5
D[28]#
AA43
A[12]#
AD4
BSEL[0]
M2
D[29]#
Y40
A[13]#
AA5
BSEL[1]
A37
D[30]#
Y44
A[14]#
AE5
BSEL[2]
C37
D[31]#
T44
A[15]#
AB2
COMP[0]
B38
D[32]#
AP44
A[16]#
AC1
COMP[1]
AE43
D[33]#
AR43
A[17]#
AN1
COMP[2]
AD44
D[34]#
AH40
A[18]#
AK4
COMP[3]
AE1
D[35]#
AF40
A[19]#
AG1
D[0]#
AF2
D[36]#
AJ43
A[20]#
AT4
D[1]#
F40
D[37]#
AG41
A[21]#
AK2
D[2]#
G43
D[38]#
AF44
A[22]#
AT2
D[3]#
E43
D[39]#
AH44
A[23]#
AH2
D[4]#
J43
D[40]#
AM44
A[24]#
AF4
D[5]#
H40
D[41]#
AN43
A[25]#
AJ5
D[6]#
H44
D[42]#
AM40
A[26]#
AH4
D[7]#
G39
D[43]#
AK40
A[27]#
AM4
D[8]#
E41
D[44]#
AG43
A[28]#
AP4
D[9]#
L41
D[45]#
AP40
A[29]#
AR5
D[10]#
K44
D[46]#
AN41
A[30]#
AJ1
D[11]#
N41
D[47]#
AL41
A[31]#
AL1
D[12]#
T40
D[48]#
AV38
A[32]#
AM2
D[13]#
M40
D[49]#
AT44
A[33]#
AU5
D[14]#
M44
D[50]#
AV40
A[34]#
AP2
D[15]#
L43
D[51]#
AU41
A[35]#
AR1
D[16]#
P44
D[52]#
AW41
ADS#
C7
D[17]#
V40
D[53]#
AR41
ADSTB[0]#
M4
D[18]#
V44
D[54]#
BA37
ADSTB[1]#
Y4
D[19]#
AB44
D[55]#
BB38
Datasheet
Package Mechanical Specifications and Pin Information
Table 18.Intel Core 2 Duo Mobile Processor in SFF Package Listing by Ball Name
Datasheet
Signal
Name
Ball
Number
Signal Name
Ball
Number
Signal
Name
Ball
Number
D[56]#
AY36
PRDY#
AV10
TMS
AW5
D[57]#
AT40
PREQ#
AV2
TRDY#
L1
D[58]#
BC35
PROCHOT#
D38
TRST#
AV8
D[59]#
BC39
PSI#
BD10
VCC
AA33
D[60]#
BA41
PWRGOOD
E7
VCC
AB16
D[61]#
BB40
REQ[0]#
R1
VCC
AB18
D[62]#
BA35
REQ[1]#
R5
VCC
AB20
D[63]#
AU43
REQ[2]#
U1
VCC
AB22
DBR#
J7
REQ[3]#
P4
VCC
AB24
DBSY#
J1
REQ[4]#
W5
VCC
AB26
DEFER#
N5
RESET#
G5
VCC
AB28
DINV[0]#
P40
RS[0]#
K2
VCC
AB30
DINV[1]#
R43
RS[1]#
H4
VCC
AB32
DINV[2]#
AJ41
RS[2]#
K4
VCC
AC33
DINV[3]#
BC37
RSVD01
V2
VCC
AD16
DPRSTP#
G7
RSVD02
Y2
VCC
AD18
DPSLP#
B8
RSVD03
AG5
VCC
AD20
DPWR#
C41
RSVD04
AL5
VCC
AD22
DRDY#
F38
RSVD05
J9
VCC
AD24
DSTBN[0]#
K40
RSVD06
F4
VCC
AD26
DSTBN[1]#
U43
RSVD07
H8
VCC
AD28
DSTBN[2]#
AK44
SLP#
D10
VCC
AD30
DSTBN[3]#
AY40
SMI#
E5
VCC
AD32
DSTBP[0]#
J41
STPCLK#
F8
VCC
AE33
DSTBP[1]#
W43
TCK
AV4
VCC
AF16
DSTBP[2]#
AL43
TDI
AW7
VCC
AF18
DSTBP[3]#
AY38
TDO
AU1
VCC
AF20
FERR#
D4
TEST1
E37
VCC
AF22
GTLREF
AW43
TEST2
D40
VCC
AF24
HIT#
H2
TEST3
C43
VCC
AF26
HITM#
F2
TEST4
AE41
VCC
AF28
IERR#
B40
TEST5
AY10
VCC
AF30
IGNNE#
F10
TEST6
AC43
VCC
AF32
INIT#
D8
THERMTRIP#
B10
VCC
AG33
LINT0
C9
THRMDA
BB34
VCC
AH16
LINT1
C5
THRMDC
BD34
VCC
AH18
LOCK#
N1
THERMTRIP#
B10
VCC
AH20
85
Package Mechanical Specifications and Pin Information
Table 18.Intel Core 2 Duo Mobile Processor in SFF Package Listing by Ball Name
86
Signal
Name
Ball
Number
Signal Name
Ball
Number
Signal
Name
Ball
Number
VCC
AH22
VCC
AP32
VCC
B22
VCC
AH24
VCC
AR33
VCC
B24
VCC
AH26
VCC
AT14
VCC
B26
VCC
AH28
VCC
AT16
VCC
B28
VCC
AH30
VCC
AT18
VCC
B30
VCC
AH32
VCC
AT20
VCC
BB14
VCC
AJ33
VCC
AT22
VCC
BB16
VCC
AK16
VCC
AT24
VCC
BB18
VCC
AK18
VCC
AT26
VCC
BB20
VCC
AK20
VCC
AT28
VCC
BB22
VCC
AK22
VCC
AT30
VCC
BB24
VCC
AK24
VCC
AT32
VCC
BB26
VCC
AK26
VCC
AT34
VCC
BB28
VCC
AK28
VCC
AU33
VCC
BB30
VCC
AK30
VCC
AV14
VCC
BB32
VCC
AK32
VCC
AV16
VCC
BD14
VCC
AL33
VCC
AV18
VCC
BD16
VCC
AM14
VCC
AV20
VCC
BD18
VCC
AM16
VCC
AV22
VCC
BD20
VCC
AM18
VCC
AV24
VCC
BD22
VCC
AM20
VCC
AV26
VCC
BD24
VCC
AM22
VCC
AV28
VCC
BD26
VCC
AM24
VCC
AV30
VCC
BD28
VCC
AM26
VCC
AV32
VCC
BD30
VCC
AM28
VCC
AY14
VCC
BD32
VCC
AM30
VCC
AY16
VCC
D16
VCC
AM32
VCC
AY18
VCC
D18
VCC
AN33
VCC
AY20
VCC
D20
VCC
AP14
VCC
AY22
VCC
D22
VCC
AP16
VCC
AY24
VCC
D24
VCC
AP18
VCC
AY26
VCC
D26
VCC
AP20
VCC
AY28
VCC
D28
VCC
AP22
VCC
AY30
VCC
D30
VCC
AP24
VCC
AY32
VCC
F16
VCC
AP26
VCC
B16
VCC
F18
VCC
AP28
VCC
B18
VCC
F20
VCC
AP30
VCC
B20
VCC
F22
Datasheet
Package Mechanical Specifications and Pin Information
Table 18.Intel Core 2 Duo Mobile Processor in SFF Package Listing by Ball Name
Datasheet
Signal
Name
Ball
Number
Signal Name
Ball
Number
Signal
Name
Ball
Number
VCC
F24
VCC
P18
VCC
Y32
VCC
F26
VCC
P20
VCCA
B34
VCC
F28
VCC
P22
VCCA
D34
VCC
F30
VCC
P24
VCCP
A13
VCC
F32
VCC
P26
VCCP
A33
VCC
G33
VCC
P28
VCCP
AA7
VCC
H16
VCC
P30
VCCP
AA9
VCC
H18
VCC
P32
VCCP
AA11
VCC
H20
VCC
R33
VCCP
AA13
VCC
H22
VCC
T16
VCCP
AA35
VCC
H24
VCC
T18
VCCP
AA37
VCC
H26
VCC
T20
VCCP
AB10
VCC
H28
VCC
T22
VCCP
AB12
VCC
H30
VCC
T24
VCCP
AB14
VCC
H32
VCC
T26
VCCP
AB36
VCC
J33
VCC
T28
VCCP
AB38
VCC
K16
VCC
T30
VCCP
AC7
VCC
K18
VCC
T32
VCCP
AC9
VCC
K20
VCC
U33
VCCP
AC11
VCC
K22
VCC
V16
VCCP
AC13
VCC
K24
VCC
V18
VCCP
AC35
VCC
K26
VCC
V20
VCCP
AC37
VCC
K28
VCC
V22
VCCP
AD14
VCC
K30
VCC
V24
VCCP
AE7
VCC
K32
VCC
V26
VCCP
AE9
VCC
L33
VCC
V28
VCCP
AE11
VCC
M16
VCC
V30
VCCP
AE13
VCC
M18
VCC
V32
VCCP
AE35
VCC
M20
VCC
W33
VCCP
AE37
VCC
M22
VCC
Y16
VCCP
AF10
VCC
M24
VCC
Y18
VCCP
AF12
VCC
M26
VCC
Y20
VCCP
AF14
VCC
M28
VCC
Y22
VCCP
AF36
VCC
M30
VCC
Y24
VCCP
AF38
VCC
M32
VCC
Y26
VCCP
AG7
VCC
N33
VCC
Y28
VCCP
AG9
VCC
P16
VCC
Y30
VCCP
AG11
87
Package Mechanical Specifications and Pin Information
Table 18.Intel Core 2 Duo Mobile Processor in SFF Package Listing by Ball Name
88
Signal
Name
Ball
Number
Signal Name
Ball
Number
Signal
Name
Ball
Number
VCCP
AG13
VCCP
B12
VCCP
M14
VCCP
AG35
VCCP
B14
VCCP
N7
VCCP
AG37
VCCP
B32
VCCP
N9
VCCP
AH14
VCCP
C13
VCCP
N11
VCCP
AJ7
VCCP
C33
VCCP
N13
VCCP
AJ9
VCCP
D12
VCCP
N35
VCCP
AJ11
VCCP
D14
VCCP
N37
VCCP
AJ13
VCCP
D32
VCCP
P10
VCCP
AJ35
VCCP
E11
VCCP
P12
VCCP
AJ37
VCCP
E13
VCCP
P14
VCCP
AK10
VCCP
E33
VCCP
P36
VCCP
AK12
VCCP
E35
VCCP
P38
VCCP
AK14
VCCP
F12
VCCP
R7
VCCP
AK36
VCCP
F14
VCCP
R9
VCCP
AK38
VCCP
F34
VCCP
R11
VCCP
AL7
VCCP
F36
VCCP
R13
VCCP
AL9
VCCP
G11
VCCP
R35
VCCP
AL11
VCCP
G13
VCCP
R37
VCCP
AL13
VCCP
G35
VCCP
T14
VCCP
AL35
VCCP
H12
VCCP
U7
VCCP
AL37
VCCP
H14
VCCP
U9
VCCP
AN7
VCCP
H36
VCCP
U11
VCCP
AN9
VCCP
J11
VCCP
U13
VCCP
AN11
VCCP
J13
VCCP
U35
VCCP
AN13
VCCP
J35
VCCP
U37
VCCP
AN35
VCCP
J37
VCCP
V10
VCCP
AN37
VCCP
K10
VCCP
V12
VCCP
AP10
VCCP
K12
VCCP
V14
VCCP
AP12
VCCP
K14
VCCP
V36
VCCP
AP36
VCCP
K36
VCCP
V38
VCCP
AP38
VCCP
K38
VCCP
W7
VCCP
AR7
VCCP
L7
VCCP
W9
VCCP
AR9
VCCP
L9
VCCP
W11
VCCP
AR11
VCCP
L11
VCCP
W13
VCCP
AR13
VCCP
L13
VCCP
W35
VCCP
AU11
VCCP
L35
VCCP
W37
VCCP
AU13
VCCP
L37
VCCP
Y14
Datasheet
Package Mechanical Specifications and Pin Information
Table 18.Intel Core 2 Duo Mobile Processor in SFF Package Listing by Ball Name
Datasheet
Signal
Name
Ball
Number
Signal Name
Ball
Number
Signal
Name
Ball
Number
VCCSENSE
BD12
VSS
AB42
VSS
AG17
VID[0]
BD8
VSS
AC3
VSS
AG19
VID[1]
BC7
VSS
AC15
VSS
AG21
VID[2]
BB10
VSS
AC17
VSS
AG23
VID[3]
BB8
VSS
AC19
VSS
AG25
VID[4]
BC5
VSS
AC21
VSS
AG27
VID[5]
BB4
VSS
AC23
VSS
AG29
VID[6]
AY4
VSS
AC25
VSS
AG31
VSS
A5
VSS
AC27
VSS
AG39
VSS
A7
VSS
AC29
VSS
AH6
VSS
A9
VSS
AC31
VSS
AH8
VSS
A11
VSS
AC39
VSS
AH10
VSS
A15
VSS
AD6
VSS
AH12
VSS
A17
VSS
AD8
VSS
AH34
VSS
A19
VSS
AD10
VSS
AH36
VSS
A21
VSS
AD12
VSS
AH38
VSS
A23
VSS
AD34
VSS
AH42
VSS
A25
VSS
AD36
VSS
AJ3
VSS
A27
VSS
AD38
VSS
AJ15
VSS
A29
VSS
AD42
VSS
AJ17
VSS
A31
VSS
AE3
VSS
AJ19
VSS
A39
VSS
AE15
VSS
AJ21
VSS
A41
VSS
AE17
VSS
AJ23
VSS
AA3
VSS
AE19
VSS
AJ25
VSS
AA15
VSS
AE21
VSS
AJ27
VSS
AA17
VSS
AE23
VSS
AJ29
VSS
AA19
VSS
AE25
VSS
AJ31
VSS
AA21
VSS
AE27
VSS
AJ39
VSS
AA23
VSS
AE29
VSS
AK6
VSS
AA25
VSS
AE31
VSS
AK8
VSS
AA27
VSS
AE39
VSS
AK34
VSS
AA29
VSS
AF6
VSS
AK42
VSS
AA31
VSS
AF8
VSS
AL3
VSS
AA39
VSS
AF34
VSS
AL15
VSS
AB6
VSS
AF42
VSS
AL17
VSS
AB8
VSS
AG3
VSS
AL19
VSS
AB34
VSS
AG15
VSS
AL21
89
Package Mechanical Specifications and Pin Information
Table 18.Intel Core 2 Duo Mobile Processor in SFF Package Listing by Ball Name
90
Signal
Name
Ball
Number
Signal Name
Ball
Number
Signal
Name
Ball
Number
VSS
AL23
VSS
AR29
VSS
AW13
VSS
AL25
VSS
AR31
VSS
AW15
VSS
AL27
VSS
AR35
VSS
AW17
VSS
AL29
VSS
AR37
VSS
AW19
VSS
AL31
VSS
AR39
VSS
AW21
VSS
AL39
VSS
AT6
VSS
AW23
VSS
AM6
VSS
AT8
VSS
AW25
VSS
AM8
VSS
AT10
VSS
AW27
VSS
AM10
VSS
AT12
VSS
AW29
VSS
AM12
VSS
AT36
VSS
AW31
VSS
AM34
VSS
AT38
VSS
AW33
VSS
AM36
VSS
AT42
VSS
AW35
VSS
AM38
VSS
AU3
VSS
AW37
VSS
AM42
VSS
AU7
VSS
AW39
VSS
AN3
VSS
AU9
VSS
AY6
VSS
AN15
VSS
AU15
VSS
AY12
VSS
AN17
VSS
AU17
VSS
AY34
VSS
AN19
VSS
AU19
VSS
AY42
VSS
AN21
VSS
AU21
VSS
AY44
VSS
AN23
VSS
AU23
VSS
B4
VSS
AN25
VSS
AU25
VSS
B6
VSS
AN27
VSS
AU27
VSS
B36
VSS
AN29
VSS
AU29
VSS
B42
VSS
AN31
VSS
AU31
VSS
BA1
VSS
AN39
VSS
AU35
VSS
BA3
VSS
AP6
VSS
AU37
VSS
BA9
VSS
AP8
VSS
AU39
VSS
BA11
VSS
AP34
VSS
AV6
VSS
BA13
VSS
AP42
VSS
AV12
VSS
BA15
VSS
AR3
VSS
AV34
VSS
BA17
VSS
AR15
VSS
AV36
VSS
BA19
VSS
AR17
VSS
AV42
VSS
BA21
VSS
AR19
VSS
AV44
VSS
BA23
VSS
AR21
VSS
AW1
VSS
BA25
VSS
AR23
VSS
AW3
VSS
BA27
VSS
AR25
VSS
AW9
VSS
BA29
VSS
AR27
VSS
AW11
VSS
BA31
Datasheet
Package Mechanical Specifications and Pin Information
Table 18.Intel Core 2 Duo Mobile Processor in SFF Package Listing by Ball Name
Datasheet
Signal
Name
Ball
Number
Signal Name
Ball
Number
Signal
Name
Ball
Number
VSS
BA33
VSS
C31
VSS
H10
VSS
BA39
VSS
C39
VSS
H34
VSS
BA43
VSS
D2
VSS
H38
VSS
BB2
VSS
D6
VSS
H42
VSS
BB6
VSS
D36
VSS
J3
VSS
BB12
VSS
D42
VSS
J15
VSS
BB36
VSS
D44
VSS
J17
VSS
BB42
VSS
E1
VSS
J19
VSS
BC3
VSS
E3
VSS
J21
VSS
BC9
VSS
E9
VSS
J23
VSS
BC11
VSS
E15
VSS
J25
VSS
BC15
VSS
E17
VSS
J27
VSS
BC17
VSS
E19
VSS
J29
VSS
BC19
VSS
E21
VSS
J31
VSS
BC21
VSS
E23
VSS
J39
VSS
BC23
VSS
E25
VSS
K6
VSS
BC25
VSS
E27
VSS
K8
VSS
BC27
VSS
E29
VSS
K34
VSS
BC29
VSS
E31
VSS
K42
VSS
BC31
VSS
E39
VSS
L3
VSS
BC33
VSS
F6
VSS
L15
VSS
BC41
VSS
F42
VSS
L17
VSS
BD4
VSS
F44
VSS
L19
VSS
BD6
VSS
G1
VSS
L21
VSS
BD36
VSS
G3
VSS
L23
VSS
BD38
VSS
G9
VSS
L25
VSS
BD40
VSS
G15
VSS
L27
VSS
C3
VSS
G17
VSS
L29
VSS
C11
VSS
G19
VSS
L31
VSS
C15
VSS
G21
VSS
L39
VSS
C17
VSS
G23
VSS
M6
VSS
C19
VSS
G25
VSS
M8
VSS
C21
VSS
G27
VSS
M10
VSS
C23
VSS
G29
VSS
M12
VSS
C25
VSS
G31
VSS
M34
VSS
C27
VSS
G37
VSS
M36
VSS
C29
VSS
H6
VSS
M38
91
Package Mechanical Specifications and Pin Information
Table 18.Intel Core 2 Duo Mobile Processor in SFF Package Listing by Ball Name
92
Signal
Name
Ball
Number
Signal Name
Ball
Number
VSS
M42
VSS
U15
VSS
N3
VSS
U17
VSS
N15
VSS
U19
VSS
N17
VSS
U21
VSS
N19
VSS
U23
VSS
N21
VSS
U25
VSS
N23
VSS
U27
VSS
N25
VSS
U29
VSS
N27
VSS
U31
VSS
N29
VSS
U39
VSS
N31
VSS
V6
VSS
N39
VSS
V8
VSS
P6
VSS
V34
VSS
P8
VSS
V42
VSS
P34
VSS
W3
VSS
P42
VSS
W15
VSS
R3
VSS
W17
VSS
R15
VSS
W19
VSS
R17
VSS
W21
VSS
R19
VSS
W23
VSS
R21
VSS
W25
VSS
R23
VSS
W27
VSS
R25
VSS
W29
VSS
R27
VSS
W31
VSS
R29
VSS
W39
VSS
R31
VSS
Y6
VSS
R39
VSS
Y8
VSS
T6
VSS
Y10
VSS
T8
VSS
Y12
VSS
T10
VSS
Y34
VSS
T12
VSS
Y36
VSS
T34
VSS
Y38
VSS
T36
VSS
Y42
VSS
T38
VSSSENSE
BC13
VSS
T42
VSS
U3
VSS
U5
Signal
Name
Ball
Number
Datasheet
Package Mechanical Specifications and Pin Information
4.3
Alphabetical Signals Reference
Table 19.
Signal Description (Sheet 1 of 8)
Name
A[35:3]#
A20M#
Type
Description
Input/
Output
A[35:3]# (Address) define a 236-byte physical memory address
space. In sub-phase 1 of the address phase, these pins transmit the
address of a transaction. In sub-phase 2, these pins transmit
transaction type information. These signals must connect the
appropriate pins of both agents on the processor FSB. A[35:3]# are
source-synchronous signals and are latched into the receiving
buffers by ADSTB[1:0]#. Address signals are used as straps, which
are sampled before RESET# is deasserted.
Input
If A20M# (Address-20 Mask) is asserted, the processor masks
physical address bit 20 (A20#) before looking up a line in any
internal cache and before driving a read/write transaction on the
bus. Asserting A20M# emulates the 8086 processor's address
wrap-around at the 1-MB boundary. Assertion of A20M# is only
supported in real mode.
A20M# is an asynchronous signal. However, to ensure recognition
of this signal following an input/output write instruction, it must be
valid along with the TRDY# assertion of the corresponding input/
output Write bus transaction.
ADS#
Input/
Output
ADS# (Address Strobe) is asserted to indicate the validity of the
transaction address on the A[35:3]# and REQ[4:0]# pins. All bus
agents observe the ADS# activation to begin parity checking,
protocol checking, address decode, internal snoop, or deferred
reply ID match operations associated with the new transaction.
Address strobes are used to latch A[35:3]# and REQ[4:0]# on their
rising and falling edges. Strobes are associated with signals as
shown below.
ADSTB[1:0]#
BCLK[1:0]
Input/
Output
Input
Signals
Associated Strobe
REQ[4:0]#, A[16:3]#
ADSTB[0]#
A[35:17]#
ADSTB[1]#
The differential pair BCLK (Bus Clock) determines the FSB
frequency. All FSB agents must receive these signals to drive their
outputs and latch their inputs.
All external timing parameters are specified with respect to the
rising edge of BCLK0 crossing VCROSS.
BNR#
BPM[2:1]#
BPM[3,0]#
Datasheet
Input/
Output
Output
Input/
Output
BNR# (Block Next Request) is used to assert a bus stall by any bus
agent who is unable to accept new bus transactions. During a bus
stall, the current bus owner cannot issue any new transactions.
BPM[3:0]# (Breakpoint Monitor) are breakpoint and performance
monitor signals. They are outputs from the processor that indicate
the status of breakpoints and programmable counters used for
monitoring processor performance. BPM[3:0]# should connect the
appropriate pins of all processor FSB agents.This includes debug or
performance monitoring tools.
93
Package Mechanical Specifications and Pin Information
Table 19.
Signal Description (Sheet 2 of 8)
Name
Type
Description
BPRI#
Input
BPRI# (Bus Priority Request) is used to arbitrate for ownership of
the FSB. It must connect the appropriate pins of both FSB agents.
Observing BPRI# active (as asserted by the priority agent) causes
the other agent to stop issuing new requests, unless such requests
are part of an ongoing locked operation. The priority agent keeps
BPRI# asserted until all of its requests are completed, then releases
the bus by deasserting BPRI#.
BR0#
Input/
Output
BR0# is used by the processor to request the bus. The arbitration is
done between the processor (Symmetric Agent) and GMCH (High
Priority Agent).
BSEL[2:0]
Output
BSEL[2:0] (Bus Select) are used to select the processor input clock
frequency. Table 3 defines the possible combinations of the signals
and the frequency associated with each combination. The required
frequency is determined by the processor, chipset and clock
synthesizer. All agents must operate at the same frequency.
COMP[3:0]
Analog
COMP[3:0] must be terminated on the system board using
precision (1% tolerance) resistors.
D[63:0]# (Data) are the data signals. These signals provide a
64-bit data path between the FSB agents, and must connect the
appropriate pins on both agents. The data driver asserts DRDY# to
indicate a valid data transfer.
D[63:0]# are quad-pumped signals and will thus be driven four
times in a common clock period. D[63:0]# are latched off the
falling edge of both DSTBP[3:0]# and DSTBN[3:0]#. Each group of
16 data signals correspond to a pair of one DSTBP# and one
DSTBN#. The following table shows the grouping of data signals to
data strobes and DINV#.
Quad-Pumped Signal Groups
D[63:0]#
Input/
Output
Data Group
DSTBN#/
DSTBP#
DINV#
D[15:0]#
0
0
D[31:16]#
1
1
D[47:32]#
2
2
D[63:48]#
3
3
Furthermore, the DINV# pins determine the polarity of the data
signals. Each group of 16 data signals corresponds to one DINV#
signal. When the DINV# signal is active, the corresponding data
group is inverted and therefore sampled active high.
94
DBR#
Output
DBR# (Data Bus Reset) is used only in processor systems where no
debug port is implemented on the system board. DBR# is used by a
debug port interposer so that an in-target probe can drive system
reset. If a debug port is implemented in the system, DBR# is a no
connect in the system. DBR# is not a processor signal.
DBSY#
Input/
Output
DBSY# (Data Bus Busy) is asserted by the agent responsible for
driving data on the FSB to indicate that the data bus is in use. The
data bus is released after DBSY# is deasserted. This signal must
connect the appropriate pins on both FSB agents.
Datasheet
Package Mechanical Specifications and Pin Information
Table 19.
Signal Description (Sheet 3 of 8)
Name
DEFER#
Type
Description
Input
DEFER# is asserted by an agent to indicate that a transaction
cannot be ensured in-order completion. Assertion of DEFER# is
normally the responsibility of the addressed memory or input/
output agent. This signal must connect the appropriate pins of both
FSB agents.
DINV[3:0]# (Data Bus Inversion) are source synchronous and
indicate the polarity of the D[63:0]# signals. The DINV[3:0]#
signals are activated when the data on the data bus is inverted. The
bus agent will invert the data bus signals if more than half the bits,
within the covered group, would change level in the next cycle.
DINV[3:0]# Assignment To Data Bus
DINV[3:0]#
Input/
Output
Bus Signal
Data Bus Signals
DINV[3]#
D[63:48]#
DINV[2]#
D[47:32]#
DINV[1]#
D[31:16]#
DINV[0]#
D[15:0]#
Input
DPRSTP#, when asserted on the platform, causes the processor to
transition from the Deep Sleep State to the Deeper Sleep state or
Deep Power Down Technology (C6) state. To return to the Deep
Sleep State, DPRSTP# must be deasserted. DPRSTP# is driven by
the ICH9M.
DPSLP#
Input
DPSLP# when asserted on the platform causes the processor to
transition from the Sleep State to the Deep Sleep state. To return to
the Sleep State, DPSLP# must be deasserted. DPSLP# is driven by
the ICH9M.
DPWR#
Input/
Output
DPWR# is a control signal used by the chipset to reduce power on
the processor data bus input buffers. The processor drives this pin
during dynamic FSB frequency switching.
DRDY#
Input/
Output
DRDY# (Data Ready) is asserted by the data driver on each data
transfer, indicating valid data on the data bus. In a multi-common
clock data transfer, DRDY# may be deasserted to insert idle clocks.
This signal must connect the appropriate pins of both FSB agents.
DPRSTP#
Data strobe used to latch in D[63:0]#.
Signals
DSTBN[3:0]#
Datasheet
Input/
Output
Associated Strobe
D[15:0]#, DINV[0]#
DSTBN[0]#
D[31:16]#, DINV[1]#
DSTBN[1]#
D[47:32]#, DINV[2]#
DSTBN[2]#
D[63:48]#, DINV[3]#
DSTBN[3]#
95
Package Mechanical Specifications and Pin Information
Table 19.
Signal Description (Sheet 4 of 8)
Name
Type
Description
Data strobe used to latch in D[63:0]#.
Signals
DSTBP[3:0]#
FERR#/PBE#
Input/
Output
Output
Associated Strobe
D[15:0]#, DINV[0]#
DSTBP[0]#
D[31:16]#, DINV[1]#
DSTBP[1]#
D[47:32]#, DINV[2]#
DSTBP[2]#
D[63:48]#, DINV[3]#
DSTBP[3]#
FERR# (Floating-point Error)/PBE# (Pending Break Event) is a
multiplexed signal and its meaning is qualified with STPCLK#. When
STPCLK# is not asserted, FERR#/PBE# indicates a floating point
when the processor detects an unmasked floating-point error.
FERR# is similar to the ERROR# signal on the Intel® 387
coprocessor, and is included for compatibility with systems using
Microsoft MS-DOS*-type floating-point error reporting. When
STPCLK# is asserted, an assertion of FERR#/PBE# indicates that
the processor has a pending break event waiting for service. The
assertion of FERR#/PBE# indicates that the processor should be
returned to the Normal state. When FERR#/PBE# is asserted,
indicating a break event, it will remain asserted until STPCLK# is
deasserted. Assertion of PREQ# when STPCLK# is active will also
cause an FERR# break event.
For additional information on the pending break event functionality,
including identification of support of the feature and enable/disable
information, refer to Volumes 3A and 3B of the Intel® 64 and IA-32
Architectures Software Developer's Manuals and the Intel®
Processor Identification and CPUID Instruction application note.
GTLREF
Input
HIT#
Input/
Output
HITM#
Input/
Output
IERR#
IGNNE#
Output
Input
GTLREF determines the signal reference level for AGTL+ input pins.
GTLREF should be set at 2/3 VCCP. GTLREF is used by the AGTL+
receivers to determine if a signal is a logical 0 or logical 1.
HIT# (Snoop Hit) and HITM# (Hit Modified) convey transaction
snoop operation results. Either FSB agent may assert both HIT#
and HITM# together to indicate that it requires a snoop stall that
can be continued by reasserting HIT# and HITM# together.
IERR# (Internal Error) is asserted by the processor as the result of
an internal error. Assertion of IERR# is usually accompanied by a
SHUTDOWN transaction on the FSB. This transaction may optionally
be converted to an external error signal (e.g., NMI) by system core
logic. The processor will keep IERR# asserted until the assertion of
RESET#, BINIT#, or INIT#.
IGNNE# (Ignore Numeric Error) is asserted to force the processor
to ignore a numeric error and continue to execute non-control
floating-point instructions. If IGNNE# is deasserted, the processor
generates an exception on a non-control floating-point instruction if
a previous floating-point instruction caused an error. IGNNE# has
no effect when the NE bit in control register 0 (CR0) is set.
IGNNE# is an asynchronous signal. However, to ensure recognition
of this signal following an input/output write instruction, it must be
valid along with the TRDY# assertion of the corresponding input/
output Write bus transaction.
96
Datasheet
Package Mechanical Specifications and Pin Information
Table 19.
Signal Description (Sheet 5 of 8)
Name
INIT#
Type
Input
Description
INIT# (Initialization), when asserted, resets integer registers inside
the processor without affecting its internal caches or floating-point
registers. The processor then begins execution at the power-on
Reset vector configured during power-on configuration. The
processor continues to handle snoop requests during INIT#
assertion. INIT# is an asynchronous signal. However, to ensure
recognition of this signal following an input/output write instruction,
it must be valid along with the TRDY# assertion of the
corresponding input/output write bus transaction. INIT# must
connect the appropriate pins of both FSB agents.
If INIT# is sampled active on the active-to-inactive transition of
RESET#, then the processor executes its Built-in Self-Test (BIST)
LINT[1:0]
Input
LINT[1:0] (Local APIC Interrupt) must connect the appropriate pins
of all APIC Bus agents. When the APIC is disabled, the LINT0 signal
becomes INTR, a maskable interrupt request signal, and LINT1
becomes NMI, a nonmaskable interrupt. INTR and NMI are
backward-compatible with the signals of those names on the
Pentium processor. Both signals are asynchronous.
Both of these signals must be software configured via BIOS
programming of the APIC register space to be used either as NMI/
INTR or LINT[1:0]. Because the APIC is enabled by default after
Reset, operation of these pins as LINT[1:0] is the default
configuration.
LOCK#
Input/
Output
PRDY#
Output
PREQ#
Input
PROCHOT#
Input/
Output
LOCK# indicates to the system that a transaction must occur
atomically. This signal must connect the appropriate pins of both
FSB agents. For a locked sequence of transactions, LOCK# is
asserted from the beginning of the first transaction to the end of
the last transaction.
When the priority agent asserts BPRI# to arbitrate for ownership of
the FSB, it will wait until it observes LOCK# deasserted. This
enables symmetric agents to retain ownership of the FSB
throughout the bus locked operation and ensure the atomicity of
lock.
Probe Ready signal used by debug tools to determine processor
debug readiness.
Probe Request signal used by debug tools to request debug
operation of the processor.
As an output, PROCHOT# (Processor Hot) will go active when the
processor temperature monitoring sensor detects that the
processor has reached its maximum safe operating temperature.
This indicates that the processor Thermal Control Circuit (TCC) has
been activated, if enabled. As an input, assertion of PROCHOT# by
the system will activate the TCC, if enabled. The TCC will remain
active until the system deasserts PROCHOT#.
By default PROCHOT# is configured as an output. The processor
must be enabled via the BIOS for PROCHOT# to be configured as
bidirectional.
This signal may require voltage translation on the motherboard.
PSI#
Datasheet
Output
Processor Power Status Indicator signal. This signal is asserted
when the processor is both in the normal state (HFM to LFM) and in
lower power states (Deep Sleep and Deeper Sleep).
97
Package Mechanical Specifications and Pin Information
Table 19.
Signal Description (Sheet 6 of 8)
Name
PWRGOOD
Type
Input
Description
PWRGOOD (Power Good) is a processor input. The processor
requires this signal to be a clean indication that the clocks and
power supplies are stable and within their specifications. ‘Clean’
implies that the signal remains low (capable of sinking leakage
current), without glitches, from the time that the power supplies
are turned on until they come within specification. The signal must
then transition monotonically to a high state.
The PWRGOOD signal must be supplied to the processor; it is used
to protect internal circuits against voltage sequencing issues. It
should be driven high throughout boundary scan operation.
REQ[4:0]#
RESET#
Input/
Output
Input
REQ[4:0]# (Request Command) must connect the appropriate pins
of both FSB agents. They are asserted by the current bus owner to
define the currently active transaction type. These signals are
source synchronous to ADSTB[0]#.
Asserting the RESET# signal resets the processor to a known state
and invalidates its internal caches without writing back any of their
contents. For a power-on Reset, RESET# must stay active for at
least two milliseconds after VCC and BCLK have reached their
proper specifications. On observing active RESET#, both FSB
agents will deassert their outputs within two clocks. All processor
straps must be valid within the specified setup time before RESET#
is deasserted.
There is a 55 Ω (nominal) on die pull-up resistor on this signal.
RS[2:0]#
RSVD
SLP#
SMI#
Input
RS[2:0]# (Response Status) are driven by the response agent (the
agent responsible for completion of the current transaction), and
must connect the appropriate pins of both FSB agents.
Reserved/
No
Connect
These pins are RESERVED and must be left unconnected on the
board. However, it is recommended that routing channels to these
pins on the board be kept open for possible future use.
Input
SLP# (Sleep), when asserted in Stop-Grant state, causes the
processor to enter the Sleep state. During Sleep state, the
processor stops providing internal clock signals to all units, leaving
only the Phase-Locked Loop (PLL) still operating. Processors in this
state will not recognize snoops or interrupts. The processor will
recognize only assertion of the RESET# signal, deassertion of SLP#,
and removal of the BCLK input while in Sleep state. If SLP# is
deasserted, the processor exits Sleep state and returns to StopGrant state, restarting its internal clock signals to the bus and
processor core units. If DPSLP# is asserted while in the Sleep state,
the processor will exit the Sleep state and transition to the Deep
Sleep state.
Input
SMI# (System Management Interrupt) is asserted asynchronously
by system logic. On accepting a System Management Interrupt, the
processor saves the current state and enters System Management
Mode (SMM). An SMI Acknowledge transaction is issued and the
processor begins program execution from the SMM handler.
If an SMI# is asserted during the deassertion of RESET#, then the
processor will tristate its outputs.
98
Datasheet
Package Mechanical Specifications and Pin Information
Table 19.
Signal Description (Sheet 7 of 8)
Name
Type
Description
STPCLK#
Input
STPCLK# (Stop Clock), when asserted, causes the processor to
enter a low power Stop-Grant state. The processor issues a StopGrant Acknowledge transaction, and stops providing internal clock
signals to all processor core units except the FSB and APIC units.
The processor continues to snoop bus transactions and service
interrupts while in Stop-Grant state. When STPCLK# is deasserted,
the processor restarts its internal clock to all units and resumes
execution. The assertion of STPCLK# has no effect on the bus
clock; STPCLK# is an asynchronous input.
TCK
Input
TCK (Test Clock) provides the clock input for the processor Test Bus
(also known as the Test Access Port).
TDI
Input
TDI (Test Data In) transfers serial test data into the processor. TDI
provides the serial input needed for JTAG specification support.
TDO
Output
TDO (Test Data Out) transfers serial test data out of the processor.
TDO provides the serial output needed for JTAG specification
support.
TEST1,
TEST2,
TEST3,
Input
Refer to the appropriate platform design guide for further TEST1,
TEST2, TEST3, TEST4, TEST5, TEST6 and TEST7 termination
requirements and implementation details.
THRMDA
Other
Thermal Diode Anode.
THRMDC
Other
Thermal Diode Cathode.
TEST4,
TEST5,
TEST6
TEST7
Output
The processor protects itself from catastrophic overheating by use
of an internal thermal sensor. This sensor is set well above the
normal operating temperature to ensure that there are no false
trips. The processor will stop all execution when the junction
temperature exceeds approximately 125 °C. This is signalled to the
system by the THERMTRIP# (Thermal Trip) pin.
TMS
Input
TMS (Test Mode Select) is a JTAG specification support signal used
by debug tools.
TRDY#
Input
TRDY# (Target Ready) is asserted by the target to indicate that it is
ready to receive a write or implicit writeback data transfer. TRDY#
must connect the appropriate pins of both FSB agents.
TRST#
Input
TRST# (Test Reset) resets the Test Access Port (TAP) logic. TRST#
must be driven low during power on Reset.
VCC
Input
Processor core power supply.
VSS
Input
Processor core ground node.
VCCA
Input
VCCA provides isolated power for the internal processor core PLLs.
VCCP
Input
Processor I/O Power Supply.
THERMTRIP#
Datasheet
99
Package Mechanical Specifications and Pin Information
Table 19.
Signal Description (Sheet 8 of 8)
Name
Type
Description
Output
VCCSENSE together with VSSSENSE are voltage feedback signals
that control the 2.1 mΩ loadline at the processor die. It should be
used to sense voltage near the silicon with little noise.
VID[6:0]
Output
VID[6:0] (Voltage ID) pins are used to support automatic selection
of power supply voltages (VCC). Unlike some previous generations
of processors, these are CMOS signals that are driven by the
processor. The voltage supply for these pins must be valid before
the VR can supply VCC to the processor. Conversely, the VR output
must be disabled until the voltage supply for the VID pins becomes
valid. The VID pins are needed to support the processor voltage
specification variations. See Table 2 for definitions of these pins.
The VR must supply the voltage that is requested by the pins, or
disable itself.
VSSSENSE
Output
VSSSENSE together with VCCSENSE are voltage feedback signals
that control the 2.1-mΩ loadline at the processor die. It should be
used to sense ground near the silicon with little noise.
VCCSENSE
§
100
Datasheet
Thermal Specifications and Design Considerations
5
Thermal Specifications and
Design Considerations
A complete thermal solution includes both component and system-level thermal
management features. To allow for the optimal operation and long-term reliability of
Intel processor-based systems, the system/processor thermal solution should be
designed so the processor remains within the minimum and maximum junction
temperature (TJ) specifications at the corresponding thermal design power (TDP) value
listed in the tables below
Caution:
Operating the processor outside these operating limits may result in permanent
damage to the processor and potentially other components in the system.
Table 20.
Power Specifications for the Dual-Core Extreme Edition Processor
Symbol
TDP
Processor
Number
X9100
Core Frequency & Voltage
3.06 GHz & VCCHFM
1.6 GHz & VCCLFM
44
0.8 GHz & VCCSLFM
20
Symbol
PAH,
PSGNT
Thermal Design
Power
Parameter
29
Unit
Notes
W
1, 4,
5, 6
Min
Typ
Max
Unit
Notes
—
—
18.8
W
2, 5, 7
W
2, 5, 7
W
2, 5, 8
Auto Halt, Stop Grant Power
at VCCHFM
at VCCSLFM
6.7
Sleep Power
PSLP
at VCCHFM
—
—
at VCCSLFM
17.8
6.4
Deep Sleep Power
at VCCHFM
at VCCSLFM
—
PDPRSLP
Deeper Sleep Power
—
—
1.9
W
2, 8
PDC4
Intel® Enhanced Deeper Sleep state Power
—
—
1.7
W
2, 8
PC6
Intel® Deep Power Down Power
—
—
1.3
W
2, 8
TJ
Junction Temperature
0
—
105
°C
3, 4
PDSLP
—
8.2
3.8
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is
not the maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the
processor currents at higher temperatures and extrapolating the values for the
temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal
Monitor’s automatic mode is used to indicate that the maximum TJ has been reached.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate
within specifications.
5.
Processor TDP requirements in Intel Dynamic Acceleration Technology mode are lesser
than TDP in HFM.
6.
At Tj of 105 oC
7.
At Tj of 50 oC
8.
At Tj of 35 oC
Datasheet
101
Thermal Specifications and Design Considerations
Table 21.
Power Specifications for the Dual-Core Standard Voltage Processor
Symbol
TDP
Processor
Number
T9900
T9800
T9600
T9550
T9400
Core Frequency & Voltage
3.06 GHz & VCCHFM
2.93 GHz & VCCHFM
2.80 GHz & VCCHFM
2.66 GHz & VCCHFM
2.53 GHz & VCCHFM
1.6 GHz & VCCLFM
35
0.8 GHz & VCCSLFM
12
Symbol
PAH,
PSGNT
Thermal Design
Power
Parameter
Unit
Notes
W
1, 4,
5, 6
35
35
35
35
22
Min
Typ
Max
Unit
Notes
—
—
13.9
W
2, 5, 7
W
2, 5, 7
W
2, 5, 8
W
2, 8
Auto Halt, Stop Grant Power
at VCCHFM
at VCCSLFM
5.0
Sleep Power
PSLP
at VCCHFM
—
—
at VCCSLFM
13.1
4.8
Deep Sleep Power
PDSLP
at VCCHFM
—
—
at VCCSLFM
5.5
2.2
PDPRSLP
Deeper Sleep Power
PDC4
Intel® Enhanced Deeper Sleep state Power
—
—
1.3
W
2, 8
PC6
Intel® Deep Power Down Power
—
—
0.3
W
2, 8
TJ
Junction Temperature
0
—
105
°C
3, 4
—
—
1.7
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is
not the maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the
processor currents at higher temperatures and extrapolating the values for the
temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal
Monitor’s automatic mode is used to indicate that the maximum TJ has been reached.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate
within specifications.
5.
Processor TDP requirements in Intel Dynamic Acceleration Technology mode are lesser
than TDP in HFM.
6.
At Tj of 105 oC
7.
At Tj of 50 oC
8.
At Tj of 35 oC
102
Datasheet
Thermal Specifications and Design Considerations
Table 22.
Power Specifications for the Dual-Core Low Power Standard Voltage
Processors (25W) in Standard Package
Symbol
TDP
Processor
Number
P9700
P9600
P8800
P9500
P8700
P8600
P8400
Core Frequency & Voltage
PSGNT
Parameter
Unit
Notes
W
1, 4,
5, 6
25
2.8 GHz & VCCHFM
2.667 GHz & VCCHFM
2.667 GHz & VCCHFM
2.53 GHz & VCCHFM
2.53 GHz & VCCHFM
2.4 GHz & VCCHFM
2.267 GHz & VCCHFM
1.6 GHz & VCCLFM
0.8 GHz & VCCSLFM
Symbol
PAH,
Thermal Design
Power
25
25
25
25
25
25
20
11
Min
Typ
Max
Unit
Notes
—
—
8.1
W
2, 5, 7
W
2, 5, 7
W
2, 5, 8
Auto Halt, Stop Grant Power
at VCCHFM
at VCCSLFM
3.7
Sleep Power
PSLP
at VCCHFM
at VCCSLFM
—
—
7.3
3.5
Deep Sleep Power
PDSLP
at VCCHFM
at VCCSLFM
—
—
2.9
PDPRSLP
Deeper Sleep Power
—
—
1.0
W
2, 8
PDC4
Intel® Enhanced Deeper Sleep State Power
—
—
0.9
W
2, 8
PC6
Intel® Deep Power Down Power
—
—
0.3
W
2, 8
TJ
Junction Temperature
0
—
105
°C
3, 4
2.1
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is
not the maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the
processor currents at higher temperatures and extrapolating the values for the
temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal
Monitor’s automatic mode is used to indicate that the maximum TJ has been reached.
Refer to Section 6.1 for more details.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate
within specifications.
5.
Processor TDP requirements in Intel Dynamic Acceleration Technology mode are lesser
than TDP in HFM.
6.
At Tj of 105 oC
7.
At Tj of 50 oC
8.
At Tj of 35 oC
Datasheet
103
Thermal Specifications and Design Considerations
Table 23.
Symbol
TDP
Power Specifications for the Dual-Core Power Optimized Performance (25 W)
SFF Processors
Processor
Number
PSGNT
Thermal Design
Power
SP9600
2.53 GHz & HFM VCC
25
SP9400
2.4 GHz & HFM VCC
2.26 GHz & HFM VCC
25
1.6 GHz & Super LFM VCC
0.8 GHz & Super LFM VCC
20
SP9300
Symbol
PAH,
Core Frequency & Voltage
Parameter
Unit
Notes
W
1, 4, 5,
6
Max
Unit
Notes
8.3
W
2, 5, 7
W
2, 5, 7
W
2, 5, 8
25
11
Min
Typ
—
—
Auto Halt, Stop Grant Power
at VCCHFM
at VCCSLFM
3.3
Sleep Power
PSLP
at VCCHFM
—
—
at VCCSLFM
7.5
3.1
Deep Sleep Power
PDSLP
at VCCHFM
at VCCSLFM
—
—
2.9
1.8
PDPRSLP
Deeper Sleep Power
—
—
1.0
W
2, 8
PDC4
Intel® Enhanced Deeper Sleep State Power
—
—
0.9
W
2, 8
PC6
Intel® Deep Power Down Power
—
—
0.3
W
2, 8
TJ
Junction Temperature
0
—
105
°C
3, 4
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is not the
maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the processor currents
at higher temperatures and extrapolating the values for the temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal Monitor’s automatic
mode is used to indicate that the maximum TJ has been reached.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate within
specifications.
5.
Processor TDP requirements in Intel Dynamic Acceleration Technology mode are lesser than TDP in HFM.
6.
At Tj of 105 oC
7.
At Tj of 50 °C
8.
At Tj of 35 oC
104
Datasheet
Thermal Specifications and Design Considerations
Table 24.
Symbol
Power Specifications fro the Dual-Core Low Voltage (LV) SFF Processors
Processor
Number
SL9600
SL9400
TDP
SL9300
Core Frequency & Voltage
Thermal Design
Power
Unit
Notes
W
1, 4, 5,
6
17
2.13 GHz & HFM VCC
1.86 GHz & HFM VCC
1.6 GHz & HFM VCC
1.6 GHz & Super LFM VCC
0.8 GHz & Super LFM VCC
17
17
16.7
10
Symbol
PAH,
PSGNT
Parameter
Min
Typ
Max
Unit
Notes
—
—
6.3
W
2, 5, 7
W
2, 5, 7
W
2, 5, 8
Auto Halt, Stop Grant Power
at VCCHFM
3.0
at VCCSLFM
Sleep Power
PSLP
at VCCHFM
—
—
5.7
2.8
at VCCSLFM
Deep Sleep Power
PDSLP
at VCCHFM
—
—
2.6
1.3
at VCCSLFM
PDPRSLP
Deeper Sleep Power
—
—
0.9
W
2, 8
PDC4
Intel® Enhanced Deeper Sleep State Power
—
—
0.8
W
2, 8
PC6
Intel® Deep Power Down Power
—
—
0.3
W
2, 8
TJ
Junction Temperature
0
—
105
°C
3, 4
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is not the
maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the processor currents
at higher temperatures and extrapolating the values for the temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal Monitor’s automatic
mode is used to indicate that the maximum TJ has been reached.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate within
specifications.
5.
Processor TDP requirements in Intel Dynamic Acceleration Technology mode are lesser than TDP in HFM.
6.
At Tj of 105 oC
7.
At Tj of 50 °C
8.
At Tj of 35 oC
Datasheet
105
Thermal Specifications and Design Considerations
Table 25.
Symbol
TDP
Power Specifications for the Dual-Core Ultra-Low-Voltage (ULV) Processors
Processor
Number
SU9600
SU9400
SU9300
Symbol
PAH,
PSGNT
Core Frequency & Voltage
Thermal Design
Power
1.4 GHz & HFM VCC
10
1.4 GHz & HFM VCC
10
1.2GHz & HFM VCC
10
1.2 GHz & Super LFM VCC
10
0.8 GHz & Super LFM VCC
8
Parameter
Notes
W
1, 4, 5,
6
Min
Typ
Max
Unit
Notes
—
—
2.9
W
2, 5, 7
W
2, 5, 7
W
2, 5, 8
W
2, 8
Auto Halt, Stop Grant Power
at VCCHFM
at VCCSLFM
1.6
Sleep Power
PSLP
Unit
at VCCHFM
—
—
—
—
at VCCSLFM
2.5
1.4
Deep Sleep Power
PDSLP
at VCCHFM
at VCCSLFM
1.3
0.9
PDPRSLP
Deeper Sleep Power
PDC4
Intel® Enhanced Deeper Sleep state Power
—
—
0.4
W
2, 8
PC6
Intel® Deep Power Down Power
—
—
0.25
W
2, 8
TJ
Junction Temperature
0
—
105
°C
3, 4
—
—
0.6
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is not the
maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the processor currents
at higher temperatures and extrapolating the values for the temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal Monitor’s automatic
mode is used to indicate that the maximum TJ has been reached.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate within
specifications.
5.
Processor TDP requirements in Intel Dynamic Acceleration Technology mode are lesser than TDP in HFM.
6.
At Tj of 105 oC
7.
At Tj of 50 °C
8.
At Tj of 35 oC
106
Datasheet
Thermal Specifications and Design Considerations
Table 26.
Symbol
TDP
Power Specifications for the Single-Core Ultra-Low-Voltage (5.5 W) SFF
Processors
Processor
Number
PSGNT
Thermal Design
Power
SU3500
1.4 GHz & HFM VCC
5.5
SU3300
1.2 GHz & HFM VCC
1.2 GHz & Super LFM VCC
0.8 GHz & Super LFM VCC
5.5
Symbol
PAH,
Core Frequency & Voltage
Parameter
5.5
Unit
Notes
W
1, 4, 5,
6
5
Min
Typ
Max
Unit
Notes
—
—
2.1
W
2, 5, 7
W
2, 5, 7
W
2, 5, 8
Auto Halt, Stop Grant Power
at VCCHFM
at VCCSLFM
1.4
Sleep Power
PSLP
at VCCHFM
—
—
at VCCSLFM
1.8
1.2
Deep Sleep Power
PDSLP
at VCCHFM
—
—
at VCCSLFM
0.7
0.6
PDPRSLP
Deeper Sleep Power
—
—
0.4
W
2, 8
PDC4
Intel® Enhanced Deeper Sleep state Power
—
—
0.3
W
2, 8
PC6
Intel® Deep Power Down Power
—
—
0.2
W
2, 8
TJ
Junction Temperature
0
—
100
°C
3, 4
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is not the
maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the processor currents
at higher temperatures and extrapolating the values for the temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal Monitor’s automatic
mode is used to indicate that the maximum TJ has been reached.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate within
specifications.
5.
Processor TDP requirements in Intel Dynamic Acceleration Technology mode are lesser than TDP in HFM.
6.
At Tj of 100 oC
7.
At Tj of 50 °C
8.
At Tj of 35 °C
Datasheet
107
Thermal Specifications and Design Considerations
5.1
Monitoring Die Temperature
The processor incorporates three methods of monitoring die temperature:
• Thermal Diode
• Intel® Thermal Monitor
• Digital Thermal Sensor
5.1.1
Thermal Diode
Intel’s processors utilize an SMBus thermal sensor to read back the voltage/current
characteristics of a substrate PNP transistor. Since these characteristics are a function
of temperature, these parameters can be used to calculate silicon temperature values.
For older silicon process technologies, it is possible to simplify the voltage/current and
temperature relationships by treating the substrate transistor as though it were a
simple diffusion diode. In this case, the assumption is that the beta of the transistor
does not impact the calculated temperature values. The resultant “diode” model
essentially predicts a quasi linear relationship between the base/emitter voltage
differential of the PNP transistor and the applied temperature (one of the
proportionality constants in this relationship is processor specific, and is known as the
diode ideality factor). Realization of this relationship is accomplished with the SMBus
thermal sensor that is connected to the transistor.
The processor, however, is built on Intel’s advanced 45-nm processor technology. Due
to this new processor technology, it is no longer possible to model the substrate
transistor as a simple diode. To accurately calculate silicon temperature use a full bipolar junction transistor-type model. In this model, the voltage/current and
temperature characteristics include an additional process dependant parameter which
is known as the transistor “beta”. System designers should be aware that the current
thermal sensors may not be configured to account for “beta” and should work with their
SMB thermal sensor vendors to ensure they have a part capable of reading the thermal
diode in BJT model.
Offset between the thermal diode-based temperature reading and the Intel Thermal
Monitor reading may be characterized using the Intel Thermal Monitor’s Automatic
mode activation of the thermal control circuit. This temperature offset must be
considered when using the processor thermal diode to implement power management
events. This offset is different than the diode Toffset value programmed into the
processor Model-Specific Register (MSR).
Table 27 and Table 28 provide the diode interface and transistor model specifications.
Table 27.
108
Thermal Diode Interface
Signal Name
Pin/Ball Number
Signal Description
THERMDA
A24
Thermal diode anode
THERMDC
A25
Thermal diode cathode
Datasheet
Thermal Specifications and Design Considerations
Table 28.
Thermal Diode Parameters Using Transistor Model
Symbol
Parameter
IFW
Forward Bias Current
IE
Emitter Current
nQ
Transistor Ideality
Beta
RT
Series Resistance
Min
Typ
Max
Unit
5
—
200
μA
1
μA
1
5
—
200
0.997
1.001
1.008
0.1
0.4
0.5
3.0
4.5
7.0
Notes
2, 3, 4
2, 3
Ω
2
NOTES:
1.
Intel does not support or recommend operation of the thermal diode under reverse bias.
2.
Characterized across a temperature range of 50-105°C.
3.
Not 100% tested. Specified by design characterization.
4.
The ideality factor, nQ, represents the deviation from ideal transistor model behavior as
exemplified by the equation for the collector current:
IC = IS * (e qVBE/nQkT –1)
where IS = saturation current, q = electronic charge, VBE = voltage across the transistor
base emitter junction (same nodes as VD), k = Boltzmann Constant, and T = absolute
temperature (Kelvin).
5.1.2
Intel® Thermal Monitor
The Intel Thermal Monitor helps control the processor temperature by activating the
TCC (Thermal Control Circuit) when the processor silicon reaches its maximum
operating temperature. The temperature at which the Intel Thermal Monitor activates
the TCC is not user configurable. Bus traffic is snooped in the normal manner and
interrupt requests are latched (and serviced during the time that the clocks are on)
while the TCC is active.
With a properly designed and characterized thermal solution, the TCC would only be
activated for very short periods of time when running the most power-intensive
applications. The processor performance impact due to these brief periods of TCC
activation is expected to be minor and hence not detectable. An under-designed
thermal solution that is not able to prevent excessive activation of the TCC in the
anticipated ambient environment may cause a noticeable performance loss and may
affect the long-term reliability of the processor. In addition, a thermal solution that is
significantly under designed may not be capable of cooling the processor even when
the TCC is active continuously.
The Intel Thermal Monitor controls the processor temperature by modulating (starting
and stopping) the processor core clocks or by initiating an Enhanced Intel SpeedStep
Technology transition when the processor silicon reaches its maximum operating
temperature. The Intel Thermal Monitor uses two modes to activate the TCC: automatic
mode and on-demand mode. If both modes are activated, automatic mode takes
precedence.
There are two automatic modes called Intel Thermal Monitor 1 (TM1) and Intel Thermal
Monitor 2 (TM2). These modes are selected by writing values to the MSRs of the
processor. After automatic mode is enabled, the TCC will activate only when the
internal die temperature reaches the maximum allowed value for operation.
When TM1 is enabled and a high temperature situation exists, the clocks will be
modulated by alternately turning the clocks off and on at a 50% duty cycle. Cycle times
are processor speed-dependent and will decrease linearly as processor core frequencies
increase. Once the temperature has returned to a non-critical level, modulation ceases
and TCC goes inactive. A small amount of hysteresis has been included to prevent rapid
Datasheet
109
Thermal Specifications and Design Considerations
active/inactive transitions of the TCC when the processor temperature is near the trip
point. The duty cycle is factory configured and cannot be modified. Also, automatic
mode does not require any additional hardware, software drivers, or interrupt handling
routines. Processor performance will be decreased by the same amount as the duty
cycle when the TCC is active.
When TM2 is enabled and a high temperature situation exists, the processor will
perform an Enhanced Intel SpeedStep Technology transition to the LFM. When the
processor temperature drops below the critical level, the processor will make an
Enhanced Intel SpeedStep Technology transition to the last requested operating point.
The processor also supports Enhanced Multi-Threaded Thermal Monitoring (EMTTM).
EMTTM is a processor feature that enhances TM2 with a processor throttling algorithm
known as Adaptive TM2. Adaptive TM2 transitions to intermediate operating points,
rather than directly to the LFM, once the processor has reached its thermal limit and
subsequently searches for the highest possible operating point. Please ensure this
feature is enabled and supported in the BIOS. Also with EMTTM enabled, the operating
system can request the processor to throttling to any point between Intel
Dynamic Acceleration Technology frequency and SuperLFM frequency as long
as these features are enabled in the BIOS and supported by the processor.
The Intel Thermal Monitor automatic mode and Enhanced Multi-Threaded
Thermal Monitoring must be enabled through BIOS for the processor to be
operating within specifications. Intel recommends TM1 and TM2 be enabled on the
processors.
TM1, TM2 and EMTTM features are collectively referred to as Adaptive Thermal
Monitoring features.
TM1 and TM2 can co-exist within the processor. If both TM1 and TM2 bits are enabled in
the auto-throttle MSR, TM2 takes precedence over TM1. However, if Force TM1 over
TM2 is enabled in MSRs via BIOS and TM2 is not sufficient to cool the processor below
the maximum operating temperature, then TM1 will also activate to help cool down the
processor.
If a processor load-based Enhanced Intel SpeedStep Technology transition (through
MSR write) is initiated when a TM2 period is active, there are two possible results:
1. If the processor load-based Enhanced Intel SpeedStep Technology transition target
frequency is higher than the TM2 transition-based target frequency, the processor
load-based transition will be deferred until the TM2 event has been completed.
2. If the processor load-based Enhanced Intel SpeedStep Technology transition target
frequency is lower than the TM2 transition-based target frequency, the processor
will transition to the processor load-based Enhanced Intel SpeedStep Technology
target frequency point.
The TCC may also be activated via on-demand mode. If bit 4 of the ACPI Intel Thermal
Monitor control register is written to a 1, the TCC will be activated immediately
independent of the processor temperature. When using on-demand mode to activate
the TCC, the duty cycle of the clock modulation is programmable via bits 3:1 of the
same ACPI Intel Thermal Monitor control register. In automatic mode, the duty cycle is
fixed at 50% on, 50% off, however in on-demand mode, the duty cycle can be
programmed from 12.5% on/ 87.5% off, to 87.5% on/12.5% off in 12.5% increments.
On-demand mode may be used at the same time automatic mode is enabled, however,
if the system tries to enable the TCC via on-demand mode at the same time automatic
mode is enabled and a high temperature condition exists, automatic mode will take
precedence.
An external signal, PROCHOT# (processor hot) is asserted when the processor detects
that its temperature is above the thermal trip point. Bus snooping and interrupt
latching are also active while the TCC is active.
110
Datasheet
Thermal Specifications and Design Considerations
Besides the thermal sensor and thermal control circuit, the Intel Thermal Monitor also
includes one ACPI register, one performance counter register, three MSR, and one I/O
pin (PROCHOT#). All are available to monitor and control the state of the Intel Thermal
Monitor feature. The Intel Thermal Monitor can be configured to generate an interrupt
upon the assertion or deassertion of PROCHOT#.
PROCHOT# will not be asserted when the processor is in the Stop Grant,
Sleep, Deep Sleep, and Deeper Sleep low-power states, hence the thermal
diode reading must be used as a safeguard to maintain the processor junction
temperature within maximum specification. If the platform thermal solution is not
able to maintain the processor junction temperature within the maximum specification,
the system must initiate an orderly shutdown to prevent damage. If the processor
enters one of the above low-power states with PROCHOT# already asserted,
PROCHOT# will remain asserted until the processor exits the low-power state and the
processor junction temperature drops below the thermal trip point. However,
PROCHOT# will de-assert for the duration of Deep Power Down Technology state (C6)
residency.
If Thermal Monitor automatic mode is disabled, the processor will be operating out of
specification. Regardless of enabling the automatic or on-demand modes, in the event
of a catastrophic cooling failure, the processor will automatically shut down when the
silicon has reached a temperature of approximately 125 °C. At this point the
THERMTRIP# signal will go active. THERMTRIP# activation is independent of processor
activity and does not generate any bus cycles. When THERMTRIP# is asserted, the
processor core voltage must be shut down within the time specified in Chapter 3.
In all cases the Intel Thermal Monitor feature must be enabled for the processor to
remain within specification.
5.1.3
Digital Thermal Sensor
The processor also contains an on-die Digital Thermal Sensor (DTS) that can be read
via an MSR (no I/O interface). Each core of the processor will have a unique digital
thermal sensor whose temperature is accessible via the processor MSRs. The DTS is the
preferred method of reading the processor die temperature since it can be located
much closer to the hottest portions of the die and can thus more accurately track the
die temperature and potential activation of processor core clock modulation via the
Thermal Monitor. The DTS is only valid while the processor is in the normal operating
state (the Normal package level low-power state).
Unlike traditional thermal devices, the DTS outputs a temperature relative to the
maximum supported operating temperature of the processor (TJ,max). It is the
responsibility of software to convert the relative temperature to an absolute
temperature. The temperature returned by the DTS will always be at or below TJ,max.
Catastrophic temperature conditions are detectable via an Out Of Specification status
bit. This bit is also part of the DTS MSR. When this bit is set, the processor is operating
out of specification and immediate shutdown of the system should occur. The processor
operation and code execution is not ensured once the activation of the Out of
Specification status bit is set.
The DTS-relative temperature readout corresponds to the Thermal Monitor (TM1/TM2)
trigger point. When the DTS indicates maximum processor core temperature has been
reached, the TM1 or TM2 hardware thermal control mechanism will activate. The DTS
and TM1/TM2 temperature may not correspond to the thermal diode reading since the
thermal diode is located in a separate portion of the die and thermal gradient between
the individual core DTS. Additionally, the thermal gradient from DTS to thermal diode
can vary substantially due to changes in processor power, mechanical and thermal
attach, and software application. The system designer is required to use the DTS to
ensure proper operation of the processor within its temperature operating
specifications.
Datasheet
111
Thermal Specifications and Design Considerations
Changes to the temperature can be detected via two programmable thresholds located
in the processor MSRs. These thresholds have the capability of generating interrupts
via the core's local APIC. Refer to the Intel® 64 and IA-32 Architectures Software
Developer's Manuals for specific register and programming details.
5.2
Out of Specification Detection
Overheat detection is performed by monitoring the processor temperature and
temperature gradient. This feature is intended for graceful shutdown before the
THERMTRIP# is activated. If the processor’s TM1 or TM2 are triggered and the
temperature remains high, an Out Of Spec status and sticky bit are latched in the
status MSR register and generates a thermal interrupt.
5.3
PROCHOT# Signal Pin
An external signal, PROCHOT# (processor hot), is asserted when the processor die
temperature has reached its maximum operating temperature. If TM1 or TM2 is
enabled, then the TCC will be active when PROCHOT# is asserted. The processor can
be configured to generate an interrupt upon the assertion or deassertion of
PROCHOT#. Refer to the an interrupt upon the assertion or deassertion of PROCHOT#.
Refer to the Intel® 64 and IA-32 Architectures Software Developer's Manuals for
specific register and programming details.
The processor implements a bi-directional PROCHOT# capability to allow system
designs to protect various components from overheating situations. The PROCHOT#
signal is bi-directional in that it can either signal when the processor has reached its
maximum operating temperature or be driven from an external source to activate the
TCC. The ability to activate the TCC via PROCHOT# can provide a means for thermal
protection of system components.
Only a single PROCHOT# pin exists at a package level of the processor. When either
core's thermal sensor trips, PROCHOT# signal will be driven by the processor package.
If only TM1 is enabled, PROCHOT# will be asserted regardless of which core is above its
TCC temperature trip point, and both cores will have their core clocks modulated. If
TM2 is enabled then, regardless of which core(s) are above the TCC temperature trip
point, both cores will enter the lowest programmed TM2 performance state. It is
important to note that Intel recommends both TM1 and TM2 to be enabled.
When PROCHOT# is driven by an external agent, if only TM1 is enabled on both cores,
then both processor cores will have their core clocks modulated. If TM2 is enabled on
both cores, then both processor cores will enter the lowest programmed TM2
performance state. It should be noted that Force TM1 on TM2, enabled via BIOS, does
not have any effect on external PROCHOT#. If PROCHOT# is driven by an external
agent when TM1, TM2, and Force TM1 on TM2 are all enabled, then the processor will
still apply only TM2.
PROCHOT# may be used for thermal protection of voltage regulators (VR). System
designers can create a circuit to monitor the VR temperature and activate the TCC
when the temperature limit of the VR is reached. By asserting PROCHOT# (pulled-low)
and activating the TCC, the VR will cool down as a result of reduced processor power
consumption. Bi-directional PROCHOT# can allow VR thermal designs to target
maximum sustained current instead of maximum current. Systems should still provide
proper cooling for the VR and rely on bi-directional PROCHOT# only as a backup in case
of system cooling failure. The system thermal design should allow the power delivery
circuitry to operate within its temperature specification even while the processor is
operating at its TDP. With a properly designed and characterized thermal solution, it is
anticipated that bi-directional PROCHOT# would only be asserted for very short periods
112
Datasheet
Thermal Specifications and Design Considerations
of time when running the most power-intensive applications. An under-designed
thermal solution that is not able to prevent excessive assertion of PROCHOT# in the
anticipated ambient environment may cause a noticeable performance loss.
§
Datasheet
113
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising