OLYMPIATM BIKE RACK
OLYMPIA BIKE RACK
TM
SURFACE MOUNT INSTALLATION INSTRUCTIONS
MATERIALS INCLUDED
a
5/16" hex bit for
tamper-resistant
screws
TOOLS NEEDED
pencil
epoxy gun
c
d
epoxy
STEP BY STEP
b
1/4", 1/2" & 7/8" drill
bits for concrete
e
hammer drill
steel
wire brush
Loctite
FOR ALL OLYMPIA BIKE RACKS
a
Mark hole locations
Drill holes
Fill holes & insert anchors
• Place bike rack in desired location. Mark
center of each hole location with a
pencil.
• Use hammer drill to drill 5" deep x 7/8"
diameter anchor hole at each marked
location using a 7/8" drill bit suitable for
concrete drilling.
• Use compressed air and steel wire brush
to clean each anchor hole in accordance
with epoxy instructions.
NOTE: Forms+Surfaces recommends
starting holes with 1/4" diameter drill
bit followed by 1/2" and finally 7/8" for
maximum accuracy.
• Use epoxy in epoxy gun to fill each anchor
hole 5/8 of the hole depth in accordance
with epoxy instructions.
• Insert 1/2"-13 x 5" epoxy anchor (a) into
each anchor hole so anchor top is flush
with ground. Allow proper curing time
according to cure schedule on epoxy
instructions before moving on to Step 4.
T 800.451.0410 | www.forms-surfaces.com
© 2013 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 1 of 3 | Rev. 06-21-13
OLYMPIA BIKE RACK
TM
SURFACE MOUNT INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR ALL OLYMPIA BIKE RACKS
b
c
d
e
Position bike rack
Attach bike rack
Tighten screws
• Position bike rack so that mounting holes
line up with anchors.
• Slide 1/2" stainless steel lock washer
(c), then 1/2" stainless steel flat washer
(d) and 1/2" nylon flat washer (e) onto
each 1/2"-13 x 1-1/2" tamper-resistant
button head cap screw (b).
• Tighten screws until snug.
NOTE: Forms+Surfaces recommends
applying Loctite® or similar threadlocking adhesive.
• Insert screws into mounting holes in bike
rack and thread into anchors using
provided 5/16" hex bit for tamperresistant screws. T 800.451.0410 | www.forms-surfaces.com
© 2013 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 2 of 3 | Rev. 06-21-13
OLYMPIA BIKE RACK
TM
SURFACE MOUNT INSTALLATION INSTRUCTIONS
wall
wall
36" min
48" min
96" (72" min)
OLYMPIA BIKE RACK
60" (48" min)
36"
(24" min)
36" min
96" (72" min)
wall
wall
RECOMMENDED BICYCLE RACK SPACING PER ASSOCIATION OF PEDESTRIAN AND BICYCLE PROFESSIONALS (APBP) GUIDELINES FOR ALL OLYMPIA BIKE RACKS
T 800.451.0410 | www.forms-surfaces.com
© 2013 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 3 of 3 | Rev. 06-21-13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement