Network Master™ Series Network Master Pro MT1000A

Network Master™ Series Network Master Pro MT1000A
Product Brochure
Network Master™ Series
Network Master Pro
MT1000A
OTDR Module
MU100020A
MU100021A
MU100022A
1310/1550 nm SMF
1310/1550/850/1300 nm SMF/MMF
1310/1550/1625 nm SMF
Excellent Eco Product
2
3
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A
All-in-One
Network I&M is supported by installing the MU100020A/MU100021A/
MU100022A and MU100010A in the MT1000A.
The OTDR Module lineup includes the MU100021A for OTDR
measurements of both SM and MM fibers in high demand by the
Mobile network I&M, plus the MU100020A/MU100022A for OTDR
measurements of SM fiber used by PON networks and long- range
measurements in Core/Metro networks.
Portable
All test functions required for network verification are built into the
compact MT1000A cabinet for easy, all-in-one onsite support of
most communications standards; the standard soft carry bag
accessory is also ideal for carrying the MT1000A onsite.
Long Battery Life
Since AC power is not commonly available onsite, the MT1000A can
run for up to 6 hours (with OTDR Module) on just one battery
charge. And the optional car 12 Vdc adapter offers in-vehicle
charging, helping facilitate uninterrupted work when moving
between sites.
All-in-One Functions Required by Physical Layer I&M Tests
The MU100020A/MU100021A/MU100022A built-in light source and
power meter functions can be used for optical loss tests in addition
to OTDR tests. An optional (Option 002) visible light source can be
installed as well.
Moreover, the presence of scratches and dirt on the fiber end face
can be checked using the Video Inspection Probe (VIP).
With 10G Multi-rate Module and OTDR Module
Easy-to-Use GUI
The MT1000A GUI design simulates onsite operations to help
increase evaluation efficiency at network installation and to speedup fault troubleshooting and isolation. Additionally, the intuitive
user interface operations also help cut training time.
*: Separately sold Video Inspection Probe (External G0306B)
Easy-to-Read and Easy-to-Use 9-inch High-Resolution Touch
Screen
The large 9-inch high-resolution, full-color, touch screen is easy to
use and displays easy-to-read measurement results, helping
improve onsite work efficiency.
4
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A
Panel Layout
1
2
3
4
Rear Panel
Module MU100020A/MU100021A/MU100022A
Main Frame MT1000A
5
6
7
8
9
10
11
12
9-inch High-Resolution Touch Screen
Power Switch
Speaker (Not Used)
1
Visible Light Option
2
Optical Power Meter
3
OTDR Multi-mode Port*1
4
OTDR Single-mode Port*2
5
Audio*3
6
AUX (Interface for GPS)*3
7
Clock Input*3
8
USB Mini-B
9
USB A
10
USB A
11
Ethernet Interface (For Remote Control)
12
DC Input (18 Vdc)
Changeable Rechargeable Lithium-Ion Battery Pack
*1: MU100021A Multi-mode (850/1300 nm)
*2: MU100020A/MU100021A/MU100022A Single-mode (1310/1550/1625 nm)
*3: Not Support for OTDR Module Application
5
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A
OTDR Module Applications
Generally, depending on the optical fiber measurement environment, OTDR measurements require multiple settings such as distance
range, pulse width, measurement time, etc., making work difficult for technicians who do not generally use an OTDR. When performing
Pass/Fail evaluation of an optical network for a report, a simple intuitive GUI is key to improving work efficiency.
The MU100020A/MU100021A/MU100022A emphasizes easy-to-understand operability using three application measurement modes:
Standard OTDR Measurement, FTTA Measurement, Construction Mode and OLTS Measurement.
Standard OTDR Measurements
Graphical Display Based on Three-Window Operation: SETUP/TEST/RESULT
This sets the measurement wavelength.
Other conditions, such as distance range, measurement time, etc.,
are measured at the Auto setting conditions.
This sets the detection conditions for optical fiber connectors and
splices as well as the Pass/Fail evaluation threshold values, and
starts measurement.
This displays the Pass/Fail evaluation results for each event
graphically at the Fiber Visualizer screen.
Additionally, waveform analysis is supported by switching to the
Trace screen.
One-Button Screen Switch
The measured data are output as a PDF report by an easy onebutton operation.
6
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A
OTDR Module Applications
1: Easy Pass/Fail Evaluation Using Fiber Visualizer
The OTDR measurement results are displayed as a trace showing
the optical fiber length, losses and size of reflections, as well as an
easy-to-view summary of the analysis results on the Fiber Visualizer
screen.
3: Intuitive Manual Waveform Analysis Using Touch Panel
Operation
Using the Trace screen, it is also possible to perform manual
analysis while moving the cursor on the captured waveform. Since
the MT1000A has a touch panel, the optical fiber length, loss, and
reflection attenuation can be analyzed manually using intuitive
direct operations on the waveform.
Fiber Visualizer Screen
• Event icons showing characteristics of each connector, splice, and
far end
• Pass/Fail evaluations based on user-settable threshold values
The user can set any threshold value for each event. If the Pass/Fail
evaluation settings prescribed in the engineering manual are set
beforehand, the measured optical fiber loss status can be easily
distinguished visually at the same time as measurement ends.
2: Accurate Event Detection Using Multiple Pulse Widths
This function measures using multiple pulse widths during one
measurement.
Manual Analysis Screen
4: Supports Long-Distance Optical Fibers and PON Network
Measurements with 1 × 128 Splitters
OTDR measurements of long optical fibers exceeding 100 km as well
as PON networks including many splitters require an OTDR with high
dynamic-range performance.
With its high dynamic range of 46 dB (typical), the MU100020A/
MU100022A is ideal for evaluating Core/Metro/Access optical fiber
networks.
Optical networks are often composed of networks using fibers
ranging in lengths from a few meters to several kilometers. Using
the MU100020A/MU100021A/MU100022A multi-pulse technology
for measurement gives much better and more accurate detection
of events in short fibers than previous measurements.
PON Measurement Screen
Event Detection Using Multi-pulse Measurements
7
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A
OTDR Module Applications
5: Various Functions and Performance for Precision OTDR
Measurements
0.8-m Event Dead Zone
Events can be detected with a dead zone of just 0.8 m (typical). This
is ideal for measurements in a mixed environment including short
optical fibers, such as patch cords.
0.8 m
FTTA Measurements
Comparatively short optical fibers of around several hundred
meters in length are usually installed at the Mobile fronthaul FTTA.
In this type of measurement environment, measurements made by
different operators under different conditions commonly have
inconsistency problems at later data processing.
At FTTA measurement, the optical fiber installation measurement
conditions are fixed previously, so measurements are always made
under the same conditions.
Like the OTDR measurement function, each measurement result
can be analyzed at the Trace and Fiber Visualizer screens.
0.8-m Event Dead Zone
250,001 Sampling Points Max.
Up to 250,001 sampling points are supported, offering a minimum
resolution of 2 cm, and a resolution of 2 m for a distance range of
300 km.
Optical Communications/Connection Check Functions
If an optical data signal is being input to the OTDR from an external
source, the optical fiber connection status will be poor, making it
impossible to perform accurate measurement and analysis. When
an optical data signal is detected at the start of OTDR
measurement using these functions, the optical fiber connection
status is evaluated as poor, a warning is displayed, and
measurement is stopped.
FTTA Measurements
OLTS Measurements
At measurement of the optical fiber, the first basic measurement is
loss measurement using a light source and power meter. With a
built-in light source and power meter as standard, the MU100020A/
MU100021A/MU100022A can be used as an optical loss test set (OLTS).
In addition, measurement results can be managed at the Loss Table
for Pass/Fail evaluation of individual data based on set threshold
values.
Supports OTDR Data Sharing Format
The measured waveform and analysis results data from the Fiber
Visualizer and waveform screens are saved in the same common
OTDR format described in the Telcordia SR-4731 (issue 2)
standards. Not only can saved data be read by these instruments, it
can also be read by the “NETWORKS” Analysis Software running on
a PC.
OLTS Measurement Loss Table Screen
*: The PC Analysis Software does not support the Fiber Visualizer function.
Macro Bend Detection/Analysis
Macro bends can be detected and analyzed by comparing two
waveform (1310/1550/1625 nm) measurements using wavelength
bend characteristics, permitting confirmation of bending faults in
optical fibers, which is a difficult evaluation using measurement
only one wavelength.
Multi-waveform Measurement and Display Functions
This is very convenient for comparison with saved waveform data
captured at network commissioning as well as for comparison with
abnormal waveform data, such as that captured at macro bend
measurements.
8
Construction
Construction Mode
The “Construction mode” simplifies installation work and is especially
useful when pulling multi-core fiber cables. Work mistakes are
eliminated by automated operation using pre-settings, such as project
data (number of fibers, file names, etc.) and measurement conditions,
to facilitate efficient measurement of multi-core fiber cables.
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A
Other Shared Functions
Optical Connector End Face Inspection
This function is for analyzing the presence and state of scratches
and dirt on the fiber end face, which are one factor causing
degraded optical communications quality. Additionally, connecting
a dirty or scratched optical fiber directly to an OTDR can prevent
Pass/Fail evaluation of a previously normal fiber.
The MT1000A has a built-in VIP utility menu for analyzing the end
face of optical connectors. When the external optical fiberscope
(G0306B sold separately) is connected, scratches and dirt on the
optical connector end face can be confirmed visually. Pass/fail
evaluation of the end-face status is performed according to the
IEC61300-3-35 standard.
Simultaneous Visible Light Option/Optical Power Meter
Measurements
The visible light option (Option 002) can be used jointly with each of
the Standard OTDR, FTTA, Construction and OLTS applications,
making it possible to visually confirm breaks in the optical fiber.
Furthermore, the Standard OTDR, FTTA and Construction
applications can also be used jointly with an optical power meter,
increasing work efficiency when measuring multi optical fibers.
OTDR Operation with Optical Power Meter
Remote Operation Function
Optical Fiber End Face Inspection Screen
PDF Report Output
OTDR/FTTA measurement results can be output as a PDF report.
In addition to the summary display, the Fiber Visualizer event icons,
event table, and a waveform display can also be output. This is
useful for easy confirmation of the Pass/Fail evaluation status.
In addition, files obtained by VIP measurement can also be read as
well, creating a single convenient report.
The OTDR Module MU100020A/MU100021A/MU100022A can also
be operated remotely from a PC over a VNC connection via
Ethernet.
LAN
MT1000A
PC
*: The Windows Control Software MX100001A does not support this
operation for OTDR modules.
PDF Report
9
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A Specifications
MT1000A Mainframe Common Specifications
Display
9-inch active TFT display (800 × 480 pixels) and touch screen
Supported Languages
User selectable (English, Japanese, Simplified Chinese, Russian, French, Spanish)
USB Data Interface
MT1000A operates as host: USB 2.0 type A (2 ports), MT1000A operates as device: USB 2.0 type Mini-B (1 port)
Ethernet Interface
Ethernet 10M/100M/1000M, Connector: RJ45
Audio Interface
For connection of optional head set, Connector: 3.5-mm diameter jack
AUX Connector
For connection of optional G0325A GPS receiver
Built-in Loudspeaker
Monitors speech of voice channel, Output level: user-controlled from user Interface
Ext. Clock Input
For connection of external clock signals:
SETS (E1: 2.048 Mbps), BITS (DS1: 1.544 Mbps) or 2.048 MHz TTL signal in accordance with ITU-T G.703, 10 MHz, Connector: BNC
Dimensions and Mass
MU100020A/MU100021A/MU100022A: 257.6 (W) × 163 (H) × 25 (D) mm (without rear panel), ≤0.8 kg
with MT1000A: 257.6 (W) × 163 (H) × 84.3 (D) mm, 2.7 kg including battery (G0310A)
with MT1000A/MU100010A: 257.6 (W) × 163 (H) × 102.2 (D) mm, 3.5 kg including battery (G0310A)
Mains Adapter
Input: 100 V (ac) to 240 V (ac), 50 Hz/60 Hz
Output: 18 V (dc)
Battery
10.8 V rechargeable and replaceable intelligent Li-ion battery
Operating time: 6.0 h (with MU100020A/MU100021A/MU100022A), Telcordia GR-196-CORE Issue2, September 2010, 25°C
Environmental Conditions
Operating Temperature : 0 to +50°C, ≤85%RH (non-condensing) (with MU100020A/MU100021A/MU100022A)
Storage Temperature: –30 to +60°C, ≤90%RH (non-condensing)
(without battery or AC adapter, with MU100020A/MU100021A/MU100022A)
–20 to +50°C, ≤90%RH (non-condensing)
(with battery and AC adapter, with MU100020A/MU100021A/MU100022A)
EMC
EN61326-1, EN61000-3-2
LVD
EN61010-1
MU100020A/MU100021A/MU100022A OTDR Module Common Specifications
10
IOR Setting
1.300000 to 1.700000 (0.000001 steps)
Units
km, m, kft, ft, mi
Sampling Points
Up to 250,001
Sampling Resolution
0.02, 0.05, 0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 40 m
Loss measurement accuracy
(linearity)
±0.05 dB/dB or ±0.1 dB (whichever is greater)
Reflectance Accuracy
Single mode: ±2 dB, Multimode: ±4 dB
Distance Accuracy
±1 m ±3 × measurement distance × 10-5 ± marker resolution (excluding IOR uncertainty)
Distance Range
(IOR = 1.50000)
Single mode: 0.5, 1, 2.5, 5, 10, 25, 50, 100, 200, 300 km
Multimode: 0.5, 1, 2.5, 5, 10, 25, 50, 100 km
Realtime Sweep Time
≤0.2 sec. (Test Mode: Manual, Distance Range: 50 km, Resolution: Coarse )
Testing Modes
Standard OTDR application: Selectable automatic or manual set-up, Fiber Visualizer, Trace analysis, Light source, Power meter,
Visual fault locator (Optional)
FTTA application: Automatic set-up, Fiber Visualizer, Trace analysis, Light source, Power meter, Visual fault locator (Optional)
Construction application: O
TDR Measurement, Auto Save, Multi-core fiber measurements, Power meter,
Visual fault locator (Optional)
OLTS application: Power meter and Light source, Loss Table, Visual fault locator (Optional)
Fiber Event Analysis
Fiber condition setup: Patch-cord setup (Launch/Receive), Splitter Setup (Up to 128 branch)
User defined Auto detect threshold: Event loss (Reflective and non-reflective), Reflectance, Fiber end, Macro bend detect ON/OFF, Splitter detect: Up to 128 branch
User defined PASS/FAIL thresholds:
Non-reflective event loss (fusion), Reflective event loss (connector, mechanical), Reflectance, Fiber loss (dB/km),
Total loss, ORL, Splitter loss (Up to 128 branch)
OTDR Trace Format
Telcordia universal. SOR, issue 2 (SR-4731)
Other Functions
Loss modes: Splice loss, 2-pt loss, 2-pt LSA, dB/km loss, dB/km LSA, ORL
Averaging modes: Timed (5, 10, 15, 30 sec, 1, 2, 3, 5, 10 min.)
Live Fiber detect : Verifies presence of communication light in optical fiber
Connection check: Automatic check of OTDR to FUT connection quality, Remote Operation, Both-End Measurement
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A Specifications
MU100020A OTDR Module
Options
Wavelength*1
Fiber Type
Pulse Width
Deadzone
(Fresnel)*4
(IOR = 1.500000)
Deadzone
(Backscatter)*5
(IOR = 1.500000)
≤80 cm (typ.)
≤3.8 m/4.3 m
Dynamic Range*2, *3
Deadzone
(Fresnel)*4
(IOR = 1.500000)
Deadzone
(Backscatter)*5
(IOR = 1.500000)
42 dB/41 dB*6
29 dB/28 dB*6
≤80 cm (typ.)
≤3.8 m/4.3 m
≤4.0 m/5.0 m
Dynamic Range*2, *3
Deadzone
(Fresnel)*4
(IOR = 1.500000)
Deadzone
(Backscatter)*5
(IOR = 1.500000)
≤80 cm (typ.)
≤3.8/4.3/4.8 m
Dynamic Range*2, *3
MU100020A-020
39 dB/37.5 dB*6
MU100020A-021
1310 nm/1550 nm ±25 nm
MU100020A-022
Single Mode Fiber
3, 10, 20, 50, 100, 200, 500,
(SMF) 10 μm/125 μm 1000, 2000, 4000, 10000,
ITU-T G.652
20000 ns
42 dB/41 dB*6
46 dB/46 dB*6
25 dB/25 dB*6
(Pulse width: 100 ns)
MU100021A OTDR Module
Options
MU100021A-021
Wavelength*1
1310 nm/1550 nm ±25 nm
850 nm/1300 nm ±30 nm
Fiber Type
Pulse Width
SMF: Same as MU100020A
Single Mode Fiber
1300 nm (MMF):
(SMF) 10 μm/125 μm
3, 10, 20, 50, 100, 200,
ITU-T G.652
500, 1000, 2000, 4000 ns
850 nm (MMF):
GI Fiber
3, 10, 20, 50, 100, 200,
62.5 μm/125 μm*7
500 ns
MU100022A OTDR Module
Options
Wavelength*1
Fiber Type
MU100022A-022
1310/1550/1625 nm ±25 nm
Laser Safety*8
IEC 60825-1: 2007 CLASS 1M:
21 CFR1040.10 Excludes deviations caused by conformance to Laser Notice No. 50 dated June 24, 2007
Single Mode Fiber
3, 10, 20, 50, 100, 200, 500,
(SMF) 10 μm/125 μm 1000, 2000, 4000, 10000,
ITU-T G.652
20000 ns
*1: 25°C, Pulse width: 1 μs (1310/1550/1625 nm), 100 ns (850 nm/1300 nm),
Except for when charging the battery.
*2: Pulse widths: 20 μs (1310/1550/1625 nm), 500 ns/4 μs (850 nm/1300 nm)
Distance range: 100 km (1310/1550/1625 nm), 25 km (850 nm/1300 nm)
Averaging: 180 sec., SNR = 1, 25°C
Except for when charging the battery.
*3: Dynamic range (one-way back-scattered light), SNR = 1: The level difference
between the RMS noise level and the level where near end back-scattering
occurs.
SNR = 1
Level
Pulse Width
46/46/44 dB*6
25/25/23 dB*6
(Pulse width: 100 ns)
*4: Pulse width: 3 ns, Return loss: 40 dB, 25°C (Refer to the figure below)
Except for when charging the battery.
1.5 dB
0.5 dB
Fresnel reflection
Back-scattered light
*5: Pulse width 10 ns, return loss 55 dB, Deviation ±0.5 dB, 25°C ±5°C
*6: Typical. Subtract 1 dB for guarantee
*7: At measurement of 50 μm/125 μm MM Fiber, the dynamic range drops
by about 3.0 dB
Distance
*8: Safety measures for laser products
This product complies with optical safety standards in IEC 60825-1,
21CFR1040.10 and 1040.11; the following descriptive labels are affixed to
the product.
11
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A Specifications
Light Source Specifications
Standard on all models
Stabilized Light Source (through OTDR port)
Options
MU100020A
MU100021A
Wavelength*1
1310 nm/1550 nm ±30 nm
1310 nm/1550 nm ±30 nm
850 nm/1300 nm ±30 nm
MU100022A
1310/1550/1625 nm ±30 nm
Spectral Width*1
≤5 nm (1310 nm)
≤10 nm (850/1300/1550/1625 nm)
Fiber Type
Single Mode Fiber (SMF)
10 μm/125 μm ITU-T G.652
Single Mode Fiber (SMF)
10 μm/125 μm ITU-T G.652
GI Fiber 62.5 μm/125 μm
Single Mode Fiber (SMF)
10 μm/125 μm ITU-T G.652
Optical Connector
Same as OTDR
Output Power*1
–5 ±1.5 dBm
Output Stability*2
≤0.1 dB (1310/1550/1625 nm)
Modes of Operation
CW, 270 Hz, 1 kHz, 2 kHz
Warm up time
10 min.
Laser Safety
Same as OTDR
Power Meter Specifications
Standard on all models
Standard Power Meter (Dedicated port)
Fiber Type
Single Mode (SMF) 10 μm/125 μm ITU-T G.652, GI Fiber 62.5 μm/125 μm
Wavelength Range
800 nm to 1700 nm
Setting Wavelengths
1310, 1490, 1550, 1625, 1650, 850, 1300 nm
Measurement Range
–67 to +6 dBm (CW, 1550 nm, –60 to +3 dBm @850 nm)
–70 to +3 dBm (Modulation, 1550 nm, –63 to 0 dBm @850 nm)
Optical Connector
2.5 mm/1.25 mm Universal
Accuracy*3
±5% (–10 dBm, 1310 nm/1550 nm, CW, 25°C, Using Master FC fiber and 2.5 mm universal connector)
±10% (–10 dBm, 850 nm, CW, 25°C, Using Master FC fiber and 2.5 mm universal connector)
Modes of Operation
CW, 270 Hz, 1 kHz, 2 kHz
Central Wavelength
650 nm ±15 nm (at 25°C)
Optical Output
0 ±3 dBm (CW, 25°C)
Output Optical Fiber
10 μm/125 μm, SMF (ITU-T G.652)
Optical Connector
2.5 mm universal
Output Function
OFF, CW, Blink
Laser Safety*4
IEC 60825-1: 2007 CLASS 3R 21CFR1040.10 and 1040.11 Excludes deviations caused by conformance to Laser Notice No. 50
dated June 24, 2007
Visible Light Source (Option 002)
*1: CW, 25°C
*2: CW, –10° to +50°C (±1°C) difference between max/min. values over 1 minute, SM fiber 2 m, when an optical power meter with 40 dB or greater return loss is
used (SM),after warming up.
3:
* After zero offset
*4: Safety measures for laser products
This option complies with optical safety standards in IEC 60825-1, 21CFR1040.10 and 1040.11; the following descriptive labels are affixed to the product
12
Ordering Information
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A
Please specify the model/order number, name and quantity when ordering.
The names listed in the chart below are Order Names. The actual name of the item may differ from the Order Name.
1) Mainframe
3) Select Connector Types
Model/Order No.
Select a module polish type and connector adapter according to
the procedures in items 3-1) and 3-2).
Name
MT1000A
Network Master Pro
B0690A*2
B0728A*3
G0309A
G0310A
Z1746A
Z1747A*4
Z1748A*5
Z1817A*6
Standard Accessories
Line Cord*1: Softbag: Rear Panel Kit: AC Adapter: Li-ion Battery: Stylus: Carrying Strap: Handle: Utilities ROM: MT1000A-003
MT1000A-005*7
Main Frame Option
Connectivity for WLAN/Bluetooth
AUX I/O
3-1) Polish Types
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
2) Select OTDR Module
Select the OTDR module configuration according to the procedures
in items 2-1) and 2-2) below.
2-1) Select Base Module
Select one of the following models.
Name
MU100020A
MU100021A
MU100022A
OTDR Module (1310/1550 nm SMF)
OTDR Module (1310/1550/850/1300 nm SMF/MMF)
OTDR Module (1310/1550/1625 nm SMF)
J1693A
J1694A
W3811AE
Standard Accessories
Universal Connector 2.5 mm for OPM:
Universal Connector 1.25 mm for OPM:
Quick Reference Guide:
2-2) Select Dynamic Range Type
Select one of the following models.
MU100020A-020
MU100020A-021
MU100020A-022
MU100021A-021
MU100022A-022
Name
Standard Dynamic Range (1310/1550 nm: 39/37.5 dB)
Enhanced Dynamic Range (1310/1550 nm: 42/41 dB)
High-Performance Dynamic Range
(1310/1550 nm: 46/46 dB)
Enhanced Dynamic Range
(1310/1550/850/1300 nm: 42/41/29/28 dB)
High-Performance Dynamic Range
(1310/1550/1625 nm: 46/46/44 dB)
*9: Factory installed option only and cannot be retrofitted.
Name
UPC Polish
APC Polish
UPC Polish
APC Polish
UPC Polish
APC Polish
Factory installed option only and cannot be retrofitted.
*10:
Used by SM port. An APC connector cannot be specified for the MM
*11: port,
which uses a UPC connector.
Specify one type of connector adapter.
Model/Order No.
Name
MU100020A-037*12
MU100020A-039*12
MU100020A-040*12
MU100021A-037*13
MU100021A-039*13
MU100021A-040*13
MU100022A-037*12
MU100022A-039*12
MU100022A-040*12
For UPC Polish with Option 010
FC Connector
DIN 47256 Connector
SC Connector
FC Connector
DIN 47256 Connector
SC Connector
FC Connector
DIN 47256 Connector
SC Connector
MU100020A-025*12
MU100020A-026*12
MU100021A-025*14
MU100021A-026*15
MU100022A-025*12
MU100022A-026*12
For APC Polish with Option 011
FC Connector key width 2.0 mm
SC Connector
FC Connector key width 2.0 mm
SC Connector
FC Connector key width 2.0 mm
SC Connector
One specified connector adapter supplied free of charge.
*12:
O
ne each of same connector adapter for SM port and MM port supplied
*13: free
of charge. Cannot specify different connector adapters for each port.
One connector adapter for SM port supplied free of charge.
*14: One
connector adapter equivalent to Option 37 (FC/UPC) for MM port
supplied free of charge.
1 pc
1 pc
1 pc
*8: Factory installed option only and cannot be retrofitted.
Model/Order No.*9
Model/Order No.*10
MU100020A-010
MU100020A-011*11
MU100021A-010
MU100021A-011*11
MU100022A-010
MU100022A-011*11
3-2) Select Connector Adapter type
*1: One line cord is attached to the area to shipment
*2: In addition to accommodating the MU100020A (or MU100021A or
MU100022A) installed in the MT1000A, this bag can also accommodate
the MU100010A.
*3: Set of B0720A (Rear Panel) and B0732A (Screw Set).
Please refer to next page "Module Configuration" for details.
4:
* Shoulder strap for MT1000A.
*5: Hand strap for MT1000A.
*6: DVD ROM containing operation manual, remote script instruction
manual, etc.
7:
* It is required when using MU100090A.
Model/Order No.*8
Specify one connector polish type.
One specified connector adapter for SM port supplied free of charge.
*15: One
connector adapter equivalent to Option 40 (SC/UPC) for MM port
supplied free of charge.
4) VFL
Model/Order No.*16
MU100020A-002*17
MU100021A-002*17
MU100022A-002*17
Name
Visual Fault Locator
Visual Fault Locator
Visual Fault Locator
Factory installed option only and cannot be retrofitted.
*16:
Installs dedicated port for visible light source; 2.5 mm universal light
*17: receiver
type (connector adapter not required). J1335A required to
connect 1.25 mm fiber.
5) Replacement Adapters
Model/Order No.
MU100020A/MU100022A
MU100021A
For UPC Polish
SM port
SM port
J0617B (FC/UPC)



J0618E (DIN/UPC)






MM port
J0619B (SC/UPC)
MM port
For APC Polish
SM port
SM port
J0739A (FC/APC)


N/A
J1697A (SC/APC)


N/A
13
Ordering Information
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A
6) Select Accessories & Replacement Items
Model/Order No.
Name
Description
For MT1000A Mainframe
B0691B
B0733A
G0324A
J1569A
G0306B
Hard Case
Hard Case
Battery Charger
Car 12 Vdc Adapter
Video Inspection Probe (X400)
B0720A
B0728A
B0729A
B0730A
B0731A
B0732A
Rear Panel
Rear Panel Kit
Screw 1U
Screw 2U
Screw 3U
Screw Kit
W3810AE
J1335A
MT1000A MU100020A Network Master Pro
Operation Manual
MU/LC Connector Adapter
J1530A
J1531A
J1532A
J1533A
J1534A
J1535A
NETWORKS
J1579A
J1581A
J1575A
J1571A
SC Plug-in Converter (UPC(P)-APC(J))
SC Plug-in Converter (APC(P)-UPC(J))
FC Plug-in Converter (UPC(P)-APC(J))
FC Plug-in Converter (APC(P)-UPC(J))
LC-SC Plug-in Converter (for SM, SC(P)-LC(J))
LC-SC Plug-in Converter (for MM, SC(P)-LC(J))
PC Emulation Software for Data Analysis and Reporting
Optical cable SM LC/PC to LC/PC 3 m
Optical cable MM LC/PC to LC/PC 3 meter
Optical cable SM LC/PC to FC/PC 3 m
Optical cable SM LC/PC to SC/PC 3 m
Up to two installed modules
Up to three installed modules
Fixed x400 magnification. For visually verifying fiber end-face condition using
MT1000A Utility application
MT1000A Rear Panel
Rear Panel and Screw kit (Same as Standard accessory)
1 unit screw set (Total 4 pcs)
2 units screw set (Total 4 pcs)
3 units screw set (Total 4 pcs)
1U, 2U, 3U screw set (Total 12 pcs)
For MU100020A/MU100021A/MU100022A OTDR Modules
Printed Matter
7) Maintenance Service
Example of Ordering Configuration
Model/Order No.
MT1000A-ES210
MT1000A-ES310
MT1000A-ES510
MU100020A-ES210
MU100020A-ES310
MU100020A-ES510
MU100021A-ES210
MU100021A-ES310
MU100021A-ES510
MU100022A-ES210
MU100022A-ES310
MU100022A-ES510
Converts ferrule connector diameter from 2.5 mm → 1.25 mm for visible light
source (Option 002)
SC/UPC → SC/APC Adapter
SC/APC → SC/UPC Adapter
FC/UPC → FC/APC Adapter
FC/APC → FC/UPC Adapter
SC/UPC → LC/UPC Adapter for SM fiber
SC/UPC → LC/UPC Adapter for MM fiber
Description
1)
2-1)
2-2)
3-1)
3-2)
2 Years Extended Warranty Service
3 Years Extended Warranty Service
5 Years Extended Warranty Service
2 Years Extended Warranty Service
3 Years Extended Warranty Service
5 Years Extended Warranty Service
2 Years Extended Warranty Service
3 Years Extended Warranty Service
5 Years Extended Warranty Service
2 Years Extended Warranty Service
3 Years Extended Warranty Service
5 Years Extended Warranty Service
MT1000A
MU100020A
MU100020A-020
MU100020A-010
MU100020A-037
1)
MT1000A
2-1)MU100021A
2-2) MU100021A-021
3-1) MU100021A-011
3-2) MU100021A-025
4)
MU100021A-002
5)
J0619B
Network Master Pro
OTDR Module (1310/1550 nm SMF)
Standard Dynamic Range
UPC Connector
FC Connector
Network Master Pro
OTDR Module (1310/1550/850/1300 nm SMF/MMF)
Enhanced Dynamic Range
APC Connector
FC Connector key width 2.0 mm
Visual Fault Locator Option
Replaceable Optical Connector (SC)
• One must be specified from items 1), 2-1), 2-2), 3-1), and 3-2), but specification
from 1) is not required if the MT1000A main frame is not required.
• When the MU100020A is specified in item 2-1), select from the MU100020A
options for models for item 2-2) and later.
Module Configuration*18
1 Module
*19
*19
Network Master Pro
MT1000A
Transport Module
2 Modules
*19
10G Multirate MU100010A
OTDR Module
1310/1550 nm SMF MU100020A
1310/1550/850/1300 nm SMF/MMF MU100021A
1310/1550/1625 nm SMF MU100022A
CPRI RF Module
MU100040A
3 Modules
Any modular combination as shown in a figure.
*18:
*19: Required if the MU100010A module (10G transport) is not used rear cover.
14
High Performance GPS Disciplined Oscillator
MU100090A
Network Master Pro MT1000A, OTDR Module MU100020A/21A/22A
Related Products
Network Master Pro MT1000A
10G Multirate Module MU100010A
Installing the MU100010A in the MT1000A supports commissioning and
maintenance tests of communications networks operating at speeds from 1.5 Mbps
to 10 Gbps. In addition to Ethernet, OTN, etc., networks, the CPRI, OBSAI, and
SyncE protocols used by mobile-network base stations are supported too.
Network Master Flex MT1100A
All-in-one, up to 4-port transport tester supporting from 1.5 Mbps to 100 Gbps
including OTN, Ethernet, CPRI/OBSAI, Fibre Channel, SDH/SONET and PDH/DSn.
MT9090A Series
µOTDR Module MU909014/15
Compact OTDR for full automatic verification of optical networks, FTTH-PON,
Metro and Core.
MU909014/15
Optical Channel Analyzer Module MU909020A
Compact CWDM channel analyzer to verify power levels, drift and channel
presence of CWDM networks.
MU909020A
Gigabit Ethernet Module MU909060A
Dedicated field test solution for installation and troubleshooting Ethernet links in
access networks.
MU909060A
Light Source/Optical Power Meter CMA5 Series
ACCESS Master Mini-OTDR MT9083 Series
For optical fiber installation and maintenance.
All-in-one test tool for fiber construction and maintenance.
15
Specifications are subject to change without notice.
• United States
Anritsu Company
1155 East Collins Blvd., Suite 100, Richardson,
TX 75081, U.S.A.
Toll Free: 1-800-267-4878
Phone: +1-972-644-1777
Fax: +1-972-671-1877
• Canada
Anritsu Electronics Ltd.
700 Silver Seven Road, Suite 120, Kanata,
Ontario K2V 1C3, Canada
Phone: +1-613-591-2003
Fax: +1-613-591-1006
• Brazil
Anritsu Eletronica Ltda.
Praça Amadeu Amaral, 27 - 1 Andar
01327-010 - Bela Vista - Sao Paulo - SP
Brazil
Phone: +55-11-3283-2511
Fax: +55-11-3288-6940
• Mexico
Anritsu Company, S.A. de C.V.
Av. Ejército Nacional No. 579 Piso 9, Col. Granada
11520 México, D.F., México
Phone: +52-55-1101-2370
Fax: +52-55-5254-3147
• United Kingdom
Anritsu EMEA Ltd.
200 Capability Green, Luton, Bedfordshire, LU1 3LU, U.K.
Phone: +44-1582-433200
Fax: +44-1582-731303
• France
Anritsu S.A.
12 avenue du Québec, Bâtiment Iris 1- Silic 612,
91140 VILLEBON SUR YVETTE, France
Phone: +33-1-60-92-15-50
Fax: +33-1-64-46-10-65
• Germany
Anritsu GmbH
Nemetschek Haus, Konrad-Zuse-Platz 1
81829 München, Germany
Phone: +49-89-442308-0
Fax: +49-89-442308-55
• Italy
Anritsu S.r.l.
Via Elio Vittorini 129, 00144 Roma, Italy
Phone: +39-6-509-9711
Fax: +39-6-502-2425
• Sweden
Anritsu AB
Kistagången 20B, 164 40 KISTA, Sweden
Phone: +46-8-534-707-00
Fax: +46-8-534-707-30
• Finland
Anritsu AB
Teknobulevardi 3-5, FI-01530 VANTAA, Finland
Phone: +358-20-741-8100
Fax: +358-20-741-8111
• Denmark
Anritsu A/S
Kay Fiskers Plads 9, 2300 Copenhagen S, Denmark
Phone: +45-7211-2200
Fax: +45-7211-2210
• Russia
Anritsu EMEA Ltd.
Representation Office in Russia
Tverskaya str. 16/2, bld. 1, 7th floor.
Moscow, 125009, Russia
Phone: +7-495-363-1694
Fax: +7-495-935-8962
• Spain
Anritsu EMEA Ltd.
Representation Office in Spain
Edificio Cuzco IV, Po. de la Castellana, 141, Pta. 5
28046, Madrid, Spain
Phone: +34-915-726-761
Fax: +34-915-726-621
• United Arab Emirates
Anritsu EMEA Ltd.
Dubai Liaison Office
902, Aurora Tower,
P O Box: 500311- Dubai Internet City
Dubai, United Arab Emirates
Phone: +971-4-3758479
Fax: +971-4-4249036
• India
Anritsu India Private Limited
2nd & 3rd Floor, #837/1, Binnamangla 1st Stage,
Indiranagar, 100ft Road, Bangalore - 560038, India
Phone: +91-80-4058-1300
Fax: +91-80-4058-1301
• Singapore
Anritsu Pte. Ltd.
11 Chang Charn Road, #04-01, Shriro House
Singapore 159640
Phone: +65-6282-2400
Fax: +65-6282-2533
• P.R. China (Shanghai)
Anritsu (China) Co., Ltd.
Room 2701-2705, Tower A,
New Caohejing International Business Center
No. 391 Gui Ping Road Shanghai, 200233, P.R. China
Phone: +86-21-6237-0898
Fax: +86-21-6237-0899
• P.R. China (Hong Kong)
Anritsu Company Ltd.
Unit 1006-7, 10/F., Greenfield Tower, Concordia Plaza,
No. 1 Science Museum Road, Tsim Sha Tsui East,
Kowloon, Hong Kong, P.R. China
Phone: +852-2301-4980
Fax: +852-2301-3545
• Japan
Anritsu Corporation
8-5, Tamura-cho, Atsugi-shi, Kanagawa, 243-0016 Japan
Phone: +81-46-296-6509
Fax: +81-46-225-8359
• Korea
Anritsu Corporation, Ltd.
5FL, 235 Pangyoyeok-ro, Bundang-gu, Seongnam-si,
Gyeonggi-do, 13494 Korea
Phone: +82-31-696-7750
Fax: +82-31-696-7751
• Australia
Anritsu Pty. Ltd.
Unit 20, 21-35 Ricketts Road,
Mount Waverley, Victoria 3149, Australia
Phone: +61-3-9558-8177
Fax: +61-3-9558-8255
• Taiwan
Anritsu Company Inc.
7F, No. 316, Sec. 1, NeiHu Rd., Taipei 114, Taiwan
Phone: +886-2-8751-1816
Fax: +886-2-8751-1817
1607
Printed on Recycled Paper
Printed in Japan 06/SEP/2016 ddcm/CDT Catalog No. MT1000A_OTDR-E-A-1-(2.00)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement