Hanns.G | JT01-32E2 | Datasheet | Hanns.G JT01-32E2 32" Black LCD TV

Hanns.G JT01-32E2 32" Black LCD TV
Explanation of WARNING Symbols
Dangerous Voltage: The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the presence dangerous
voltage within the inside of the product that may be sufficient level to
constitute a risk of electric shock to persons.
Instruction: The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and servicing
instructions in the literature accompanying the appliance.
Safety instructions
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this LCD TV near water.
Clean only with dry cloth. Do not use liquid, alcohol, or aerosol cleaners.
Do not block any ventilation openings. Install your LCD TV in a well ventilated area.
Keep your LCD TV away from moisture, excessive dust and any heat sources,
such as radiators, heat registers, stoves, or any other apparatus (including
amplifiers) that produce heat.
Do not remove the back cover. There are no user-serviceable parts inside.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The third prong is provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs,
receptacles, and the point where they exit from the LCD TV.
Never rest objects on the power cord or place it in high traffic
areas.
Only use attachments/accessories specified by the
manufacturer.
Use only with stand, tripod, bracket, or table specified by the
manufacturer, or sold with the LCD TV. When a cart is used,
use caution to avoid injury from tip-over.
Unplug this LCD TV during lightening storms or when unused
for long periods of time.
Refer all servicing to qualified service personnel-- Servicing may be required if the
LCD TV has been damaged in any way, such as power-supply cord or plug
damage, liquid has been spilled or objects have fallen into the LCD TV, the LCD TV
has been exposed to rain or moisture, does not operate normally, or has been
dropped.
1
17) Do not expose your LCD TV to dripping or splashing, and do not place objects
filled with liquids on it.
18) The Shock Hazard Marking and Associated Graphical Symbol are provided on the
back panel of unit.
19) This product is only to perform the useful function of entertainment and visual
display tasks are excluded.
20) Wall or ceiling mounting: When mounting the product on a wall or ceiling, be sure
to install the product according to the method recommended by the manufacturer.
Use only the mounting hardware recommended by the manufacturer. This is a
safety feature.
CAUTION: Any damage caused by incorrectly attempting to mount
this LCD TV is not covered under the terms of the manufacturers
warranty.
WARNING: To reduce the risk of fire or electric shock, do not expose
this LCD TV to rain or moisture.
Operation Instructions
Thank you for purchasing multi-scan color LCD-TV. Please read this guide thoroughly
before installation.
HDMI Licensing Statement
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
CE Conformity for Europe
The device complies with the requirements of the EEC directive 89/336/EEC
as amended by 92/31/EEC and 93/68/EEC Art.5 with regard to
“Electromagnetic compatibility”, and 73/23/EEC as amended by 93/68/EEC
Art.13 with regard to “Safety.”
Antenna Installation Instruction
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product be sure the antenna
or cable system is grounded so as to provide some protection against voltage surges
and built-up static charges, Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
2. Lightning
For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and
2
disconnect the antenna or cable system. This will prevent damage to the product due
to lightning and power-line surges. Do not disconnect the antenna or the power cord
during a heavy storm lighting may strike while you are holding the cable cord, causing
serious injury; turn off your LCD TV and wait for the weather to improve.
3. Power Lines
An outside antenna system should not be located in the vicinity of overhead power
lines or other electric light or power circuits, or where it can fall into such power lines or
circuits, When installing an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them might be fatal.
According to WEEE regulation , this monitor can't be handled as normal trash in
Europe when it is out of usage. Please refer to the recycle information from our
website to handle it.
3
Content
ACCESSORIES...................................................................................................................1
FRONT PANEL BUTTONS ..................................................................................................2
INTERFACE.........................................................................................................................3
REMOTE CONTROL ...........................................................................................................4
INSTALLATION....................................................................................................................8
Connecting RF antenna or Cable TV Wire ...................................................................8
Connecting to External Stereo System to Listen to LCD TV Sound..............................8
Connecting to DVD/ Set Top Box..................................................................................8
Connecting to a computer...........................................................................................10
Connecting to a computer with HDMI-DVI cable ........................................................ 11
Connecting with the power cord.................................................................................. 11
BASIC OPERATION ..........................................................................................................12
Turning on the LCD TV ...............................................................................................12
Power On/Off ..............................................................................................................12
Select input source .....................................................................................................12
Volume Adjusting ........................................................................................................12
Channel Select ...........................................................................................................12
Sleep Time Setting......................................................................................................12
Sound .........................................................................................................................12
Video ..........................................................................................................................13
Using OSD Menu........................................................................................................13
ADVANCED OPERATION—OSD MENU/ REMOTE CONTROL.......................................14
Picture Menu ..............................................................................................................14
Sound Menu ...............................................................................................................14
Channel Menu ............................................................................................................15
Option Menu ...............................................................................................................17
PC Menu.....................................................................................................................17
OSD Menu..................................................................................................................18
TECHNICAL SPECIFICATION ..........................................................................................19
SAFETY PRECAUTIONS ..................................................................................................20
CARE AND MAINTENANCE .............................................................................................21
TROUBLESHOOTING.......................................................................................................21
4
ACCESSORIES
Thank you for purchasing this LCD-TV.
This LCD-TV package comes with:
LCD TV
User’s Manual
Quick Start Guide
Warranty Card
Warranty and Service Manual
Remote control
Battery AA x 2
Power Cord
VGA Cable
1
FRONT PANEL BUTTONS
❶
Volume - Down
❷
Volume + Up
❸
On Screen Display Menu On/Off
❹
Channel Down (Scroll Down)
❺
Channel Up (Scroll Up)
❻
Enter
❼
Power ON/OFF
❽
Remote Control Receiver
❾
Power LED Indicator
2
INTERFACE
A
B
C
D
E F
G H
I
J K L
M
N
A
Audio Output for AV, S-Video or YPbPr components (left/ right)
B
Audio Input for AV, S-Video or YPbPr/ HDMI-DVI components
(left/ right)
C
Audio Input for VGA
D
RF Antenna / Cable TV Input
E
AC Power Switch (Must be turned on)
F
Power Input (AC Input)
G
HDMI1 Input Terminal (19 pin)
H
HDMI2 Input Terminal (19 pin)
I
VGA (15 pin) Signal Input from Computer
J
YPbPr/ HD Component Video Input
K
S-Video Input
L
Composite Video input
M
SCART 1 Input
N
SCART2 / SCART2-SV Input
3
REMOTE CONTROL
4
Remote control button function as follows:
:
1
POWER
Power ON/OFF
2
3
DUAL I / II
INFO
MTS (Multi-Channel TV Sound) select
Display the current information
4
SLEEP
Set TV Sleep timer
5
SOUND
Select situation mode for sound
6
FREEZE
Freeze picture
7
0~9 NUMBER
Switch channel number keys
8
AVC
9
VOL UP/ DOWN
The tuner contains automatic volume control circuitry (AVC) to
prevent converter overload (for TV only)
Adjust volume up or down
10
UP/ DOWN/ LEFT/
RIGHT/ ENTER
UP/ DOWN/ LEFT/ RIGHT: Select or adjust the function of
OSD
ENTER: 1) Confirm the selection (in OSD menu)
2) Display Program List and select program channel
(in TV mode only)
11
12
INPUT
RED
Input source select
In Teletex function: move cursor down
In Name function: edit channel name / select channel for
exchange
13
GREEN
14
YELLOW
15
BLUE
16
MUTE
17
18
TV
PICTURE
In Teletex function: move cursor up
In Name function: add desired channels / select channel for
exchange
In Teletex function: change from current page to selected page
In Name function: erase desired channels
In Teletex function: go out from CURSOR Mode
In Name function: confirm edited name / confirm exchange
Volume mute ON/OFF
Direct to TV source
19
WIDE
Select situation mode for picture
Change aspect ratio
20
21
22
RETURN
PROGRAM UP/ DOWN
MENU
Return to previous channel
Select up or down programs
OSD menu ON/OFF
23
TELETEXT FUNCTION
CONTROL button
Please refer to page 6-7
5
Teletext function control button
TEXT/ MIX/ PICTURE button
In TV Mode: Press the TEXT/ MIX/ PICTURE button to enter the Teletext mode.
In TELETEXT Mode: Press the button again to superimpose a Teletext Broadcast onto the
screen of current TV program (mixed Mode).
In MIXED Mode: Press the button again to return back to the normal TV Screen (current
program).
SUBCODE button
When a selected Teletext page with hidden sub pages or timed pages, these pages can be seen by
the following manner:
Press the sub code button. Screen will show « /0001 ».
Enter 4 digits number button corresponding to the sub page desired. E.g. 0001 for sub page
number 1.
Wait until the page appears.
STORE button
Store current page in List mode.
Press the LIST button to change from FLOF system to LIST Mode.
Press a coloured button corresponding to the coloured brackets on the screen for page number
storage.
Enter the Teletext page number using the 0 ~ 9 digit buttons (enter three digits).
Press the STORE button to memorize the page numbers you require.
HOLD button
Press this button to remove the information from the display and stop the automatic page
change which will occur if a teletext page consists of 2 or more sub pages.
To continue press this button again. The number of sub pages and the sub page displayed is,
usually, shown on the screen below the time. When this button is pressed the stop symbol is
displayed at the left-top corner of the screen and the automatic changing is inhibited.
REVEAL button
Press this button to display concealed information, such as solutions of riddles or puzzles.
Press this button again to remove the information from the display.
SIZE button
Select double height text under Teletext mode for full screen.
Press this button to enlarge the top half of the page.
6
Press this button again to enlarge the bottom half of the page.
Press this button again to return to the normal display.
LIST button
Press this button you force the Teletext to LIST Mode. It means that row 24 (bottom row of
Teletext) will not have transmitting information, only the pages that you have previously stored
in the memory.
Press LIST button again to exit from LIST Mode to Teletext.
INDEX button
Press the Index button to return back to index page.
When you press this button in Teletext mode, a CURSOR appears. This cursor (rectangular
box) contains a page number and you can select the desired page simply by using the four
colours.
RED button: Move cursor down.
GREEN button: Move cursor up.
YELLOW button: Change from current page to selected page.
BLUE button: Exit the CURSOR Mode.
7
INSTALLATION
Connecting RF antenna or Cable TV Wire
Make sure the power is OFF before installing your LCD TV. Connect the LCD TV to TV antenna
wire or cable/satellite box with 75-ohm coaxial cable.
Preset the TV channels into memory with AUTO SCAN function (see page 15) when using an
antenna or cable TV system without a cable connecter box.
RF Cable or Adapter
(not supplied)
Connecting to External Stereo System to Listen to LCD TV Sound
Connect the audio output terminal of the LCD TV to the audio in terminal of the stereo
system (stereo system sold separately). When main source is selected to HDMI, audio
output is not supported.
Audio in Cable
(not supplied)
Stereo system
Connecting to DVD/ Set Top Box
Connect Video/ Audio cables from compatible devices into the back panel of LCD TV.
1) With RCA A/V cable
VCD or DVD Player
RCA A/V Cable (not supplied)
8
2) With S-Video cable:
VCD or DVD Player
Audio in Cable (not supplied)
S-Video Cable (not supplied)
3) With YPbPr cable:
YPbPr Cable (not supplied)
VCD or DVD Player
Audio in Cable (not supplied)
4) With SCART1:
SCART Cable (not supplied)
VCD or DVD Player
5) With SCART2/ SCART2-SV:
SCART Cable (not supplied)
Set top or DVD Player
9
Note:
SCART1
SCART2
SCART2-SV
Acceptable Signal
AV/RGB
AV
S-Video
Available Provided Input Source
TV only
CVBS signal
SV signal
6) With HDMI cable:
VCD or DVD Player
(DVD Player should have
the HDMI Output terminal)
HDMI Cable (not supplied)
7) With HDMI to DVI cable:
VCD or DVD Player
(DVD Player should have
the DVI Output terminal)
Audio in Cable
(not supplied)
HDMI-DVI Cable (not supplied)
Connecting to a computer
Connect the VGA cable from VGA output of the computer to the VGA terminal input of your
LCD TV. Also, connect the Audio In cable (green) from the audio output of your computer
to the audio input terminal (green) of the LCD TV.
PC
PC Audio In Cable
(not supplied)
VGA 15 Pin Cable
10
Connecting to a computer with HDMI-DVI cable
Connect the HDMI-DVI cable from the DVI output of the computer to the HDMI terminal
input of the LCD TV. Also, connect the green end of the Audio In cable from the audio
output of your computer to the audio input terminal (red/white) of the LCD TV.
PC
Audio In Cable
(not supplied)
HDMI-DVI Cable (not supplied)
Connecting with the power cord
Connect the power cord to the power cord connector on the back of your LCD TV, and
plug the other end of the power cord into a correctly grounded electrical outlet.
AC Switch
Switch to ON
AC power socket
Power Cord
11
BASIC OPERATION
To operate your LCD TV, you may use the TV remote control or upper panel buttons to
select input source, change channels, or adjust volume.
Turning on the LCD TV
Before using the LCD TV:
1. Connect external equipments properly.
2. Insert the power cord.
3. Turn on Main Power Switch, located on the rear of the cabinet (If the LCD TV will not
be used for a long period of time, please turn it off).
Power On/Off
To turn the LCD TV on/off :
Press POWER button on the bottom of the cabinet or press POWER key on your remote
control to turn on/off the TV. The power LED indicator lights when the LCD TV is on.
Select input source
Press INPUT key and use ◄► to select the required input source between PC, HDMI1,
HDMI2, TV, YPbPr, AV, SVIDEO, SCART1, SCART2, and SCART2SV.
To confirm the selection, press ENTER.
Volume Adjusting
Press VOL+/- to adjust volume.
To turn off the sound, press MUTE.
To restore volume, press MUTE again, or press VOL+/- directly.
Channel Select
Press number keys or PROG ▲▼ keys to select the desired channels.
Ex: the desired channel is 8--Press 0 → press 8, or press 8 only.
Return to the previous channel, press RETURN key.
Sleep Time Setting
Repeatedly press SLEEP key to set the off timer. The function is used to automatically shut
off the LCD TV after a preset period of time passed.
There are several times for choice -- 15min, 30min, 45min, and 60min.
To cancel Sleep Time function, choose 0 min.
Sound
Sound Mode Select
Repeatedly press SOUND to select the sound mode between User, Speech, Movie,
and Music.
MTS Select
Press DUAL I/II key to set up MTS system.
The function is to provide multi-channel TV sound. MTS can receive Dual, Stereo, SAP
(Secondary Audio Program), or Mono sound. SAP feature permits the TV station to
broadcast other information, such as audio in another language. With Dual sound, you
can enjoy the main sound (normal program soundtrack) and the second language at
the same time.
**Choose the available sound output for channels that is preset by TV broadcasting
station.
12
Program’s sound setting
dual
stereo
mono
Exchangeable sound output
dual I, dual II
stereo, mono
mono
Video
Picture Mode Select
Repeatedly press PICTURE key to select picture mode between User, Standard, Movie,
and Vivid.
Aspect Ratio Select
Repeatedly press WIDE key to select image size between Full, Zoom1, Zoom2, Normal,
Panorama, or WSS (auto format switching).
Freeze Picture
Press FREEZE key to freeze picture. However, the sound still continues.
Using OSD Menu
You are able to use On Screen Display (OSD) menus to adjust various settings by using
your remote control or menu button on the top of the LCD TV.
The basic operation is as following:
Press MENU to display OSD menu.
Press ▲▼ to select your desired top Menu.
Press ◄► to enter the menu you select.
Use ▲▼ to select the control you want to adjust.
Press ◄► to adjust or select the settings.
Press MENU again to exit the current OSD page.
PS. In OSD page, if the item is with an arrow ►, it indicates that there is a sub-OSD
page with it. You have to press ◄ or ► to get into sub-OSD page.
However, if the item is with two arrows ◄(selection)►, it means that user may just press
◄► to select the selection. There is no sub-OSD page with it.
13
ADVANCED OPERATION—OSD MENU/ REMOTE CONTROL
Picture Menu
— Adjusting the picture
It is active in TV/ AV/ S-VIDEO/ YPbPr/ SCART1/ SCART2/ SCART2SV/ HDMI1/ HDMI2 source.
Contrast: To adjust contrast of video.
Brightness: To adjust luminance of video.
Colour: To adjust colour.
Tint: To adjust tint level.
Sharpness: To adjust picture sharpness.
Fresh Tone: To adjust colour of skin.
Colour Temp.: To select colour Temp. by pressing ◄►—warm redder, normal neutral, or cool
bluer.
Reset: Press ENTER to reset all the settings in Picture page.
Sound Menu
—To adjust sound
It is active in all input sources.
Bass: To adjust the bass (It is only active when sound mode is in “User” condition).
Treble: To adjust the treble (it is only active when sound mode is in “User” condition).
Balance: To adjust left and right audio balance.
14
Equalizer: To adjust the equalizer.
Reset: Press ENTER to reset all the settings in Sound page.
Channel Menu
—To setup for TV
It is only active in TV source.
Auto Scan: To automatically preset the channels into TV’s memory. Select the country of your area
with ◄► and then press ENTER to perform Auto Scan. If the country is not listed in the selection
area, select “OTHERS.” Kindly suggest you auto scan all the channels before watching your TV for
the first time.
Note: After auto scanning all the channels, you need not to do it again when turning on your TV next time.
Manual Store: To search the detectable channels and store them into memory manually.
1. Press ◄ or ► to get into “Manual Store.”
15
2.
3.
4.
5.
6.
Move the cursor to “Prog. No, “ and select the desired channel position with ◄►.
Move the cursor to “System,“ and select the system according to your local area with◄►.
Move your cursor to “Search,” and search the detectable channels with ◄►.
Move your cursor to “Fine Tune,” and adjust the picture with ◄►.
Move to Store, then Store the instruction with ENTER.
Note: The channel will be stored instead of the former program.
Name: To enter a name for program with 0~9, +-. /, and A~Z. Press ◄ or ► to get into “Name.”
1. To enter a name:
Press red key (on the remote control) to edit a name for the channel.
Use ▲▼ to select the desired letter and use◄► to move the cursor to enter next letter. After the
desired name is entered, press blue key (OK) to confirm.
2. To Erase/ Add channels:
Use ▲▼ to select the desired channel.
Press yellow key to erase the channel or press green key to add it.
When using PROG▲▼ key, the channels you erased will be passed over. You may press green
key to add the erased channels or use Auto Scan function to re-present them.
3. To exchange one channel with another:
Press blue key to enter the function of “Sort,” and the following screen will show.
If you want to exchange channel 1 with channel 2:
16
1.
2.
3.
4.
Move your cursor to channel 1 and press red key (Sel1) to select channel 1.
Move your cursor to channel 2 and press green key (Sel2) to select channel 2.
Confirm your selection by pressing blue key (OK).
Press MENU to exit.
Option Menu
When input source is PC/TV/ AV/ SV/YPbPr/
When input source is HDMI(PC), the controls
/SCART1/ SCART2/ SCART2-SV/ HDMI(HDCP): of H-Position and V-Position are disabled:
Main Source: To select the input source between TV, YPbPr, AV, S-Video, SCART1, SCART2,
SCART2SV, PC, HDMI1 and HDMI2 with ◄►.
H-Position: To adjust the horizontal position of the video with ◄►.
V-Position: To adjust the vertical position of the video with ◄►.
OSD Language: To select the OSD language between English, French, German, Spanish, Italian,
Portuguese, Dutch, and Swedish with ◄►.
TTX Language: To select the language of Teletext content.
Reset: Press ENTER to reset all the settings in Option page.
PC Menu
—to Adjust for PC
It is only active in PC and HDMI (support PC mode).
When input source is PC:
When input source is HDMI (PC), only the
controls of Contrast, Brightness, Colour Mode,
and Reset are active:
Auto Adjust: To auto adjust picture’s horizontal position, vertical position, fine tune, and H-Size
with ◄►.
Contrast: To adjust foreground luminance of video.
17
Brightness: To adjust background luminance of video.
H-Position: To adjust horizontal position of video.
V-Position: To adjust vertical position of video.
Clock: To adjust delay time of clock in order to reduce the noise of picture.
Phase: To adjust delay time of phase in order to reduce the noise of picture.
Colour Mode: To adjust colour temperature.
1. Press ◄ or ► to get into Colour Mode.
2. Use ◄►to select between Cool, sRGB, User, Normal, and Warm.
3. When “User” is selected, it allows you to adjust the colour of red, green, and blue separately.
Reset: Press ENTER to reset all the settings in PC page.
OSD Menu
—To setup OSD window
It is active in all input sources.
H-Position: To adjust the OSD horizontal position with ◄►.
V- Position: To adjust the OSD vertical position with ◄►.
Duration: To automatically shut off the OSD after a preset period of time passed.
Use ◄►to preset the time from 5 to 60 seconds.
Reset: Press ENTER to reset all the settings in OSD page.
18
TECHNICAL SPECIFICATION
LCD
Type
31.51” TFT Active Matrix
0.51075(H) x 0.51075(V) mm pixel pitch
Input signal
Color Filter
RGB vertical stripe
Glass surface
Anti-Glare
RGB
RGB analog (0.7/1.0 Vp-p, 75 ohms)
Separate Sync,
fh: 30-80 kHz, fv:50-75 Hz
RF
TV system Antenna / PAL
Video
1 composite RCA, 1 S-Video, 1 YPbPr component,
2 HDMI, 2 SCART
Audio
1 mini-stereo, 1 pair of RCA (L/R) stereo
Compatibility
PC
Up to 1360 x 768 Non-interlaced
Resolution
Recommended
and supported
1360 x 768 @ 60 Hz
1280 x 1024 @ 60 Hz, 75 Hz
1024 x 768 @ 60, 75 Hz
800 x 600 @ 60, 75 Hz
640 x 480 @ 60, 75 Hz
Speaker Output
10W x 2
Audio Output
1 pair of RCA (L/R) stereo jack
Power
Voltage
100-240 VAC, 50/60 Hz (auto switch)
Display area
Full Scan
697.68 mm (H) x 392.25 mm (V)
27.5” (H) x 15.4” (V)
Temperature
32°F to + 104°F ( 0°C to + 40°C)
Humanity
20% to 65% (no condensation)
Altitude
To 10,000 feet (3,000m)
Temperature
-4°F to + 140°F (-20°C to + 60°C)
Humanity
10% to 90% (no condensation)
Altitude
To 40,000 feet (12,000m)
Physical
807.7mm (W) x 646.2mm (H) x 210mm (D)
Operating
conditions
Storage condition
Dimensions
31.8’’ (W) x 25.4’’ (H) x 8.3’’ (D)
Weight
Net
CE, TÜV/GS
Regulations
Power saving
modes
21.8 kg (48.0 Ib)
On
< 200 W (green LED)
Active Off
< 3 W (red LED)
Preset Timing Mode (Pre-adjusted to GTF® 1360 x 768 @ 60 Hz)
Warning: Do not set the graphics card in your computer to exceed these refresh rates; doing so
may result in permanent damage to the LCD TV
19
SAFETY PRECAUTIONS
This LCD TV is manufactured and tested to insure the user’s safety. Improper use or
installation may result danger to the LCD TV as well as to the user. Carefully go over the
following WARNINGS before installation and keep this guide handy.
WARNINGS
This LCD TV should be operated only at the correct power sources indicated on the label on
the rear end of the LCD TV. If you’re unsure of the power supply in your residence, consult your
local dealer or power company.
Do not try to repair the LCD TV yourself as it contains no user-serviceable parts. The LCD TV
should only be repaired by a qualified technician.
Do not remove the LCD TV cabinet. There is high-voltage parts inside that may cause electric
shock. even when the power cord is disconnected .
Stop using the LCD TV if the cabinet is damaged. Have it checked by a service technician.
Put your LCD TV only in a clean, dry environment. Unplug the LCD TV immediately if gets wet
and consult your service technician.
Always unplug the LCD TV before cleaning it. Clean the cabinet with a clean, dry cloth. Apply
non-ammonia based cleaner onto the cloth, not directly onto the glass screen.
Keep the LCD TV away from magnetic objects, motors, TV sets, and transformer.
Do not place heavy objects on the cable or power cord.
For PLUG CABLE EQUIPMENT, the Socket-outlet shall be installed near the equipment and
shall be easily accessible.
20
CARE AND MAINTENANCE
Care
Avoid exposing your LCD TV directly to sunlight or other heat source.
Place your LCD TV away from the sun to reduce glare.
Put your LCD TV in a well ventilated area. Do not place anything heavy on top of your LCD
TV.
Make certain your LCD TV is installed in a clean and moisture-free area.
Keep your LCD TV away from magnets, motors, transformers, speakers, and TV sets.
Safety Tips
If smoke, abnormal noise or odor came out of your LCD TV, caution should be remove the
power cord immediately and call your service center.
CAUTION-Never remove the rear cover of your LCD TV cabinet. The display unit inside
contains high-voltage parts and may cause electric shock to human bodies.
Never try to repair your LCD TV yourself. Always call your service center or a qualified
technician to fix it.
TROUBLESHOOTING
No power
Make sure A/C power cord is securely connected.
Plug another electrical device into the power outlet to verify that the outlet is supplying proper
voltage.
Power on but no screen image
Make sure the video cable supplied with the TV is tightly secured to the video output port on
back of video source (DVD, VCR…). If not, tightly secure it.
Adjust brightness.
Make sure all signal cables are installed.
Wrong or abnormal colors
If any colors (red, green, blue) are missing, check the video cable to make sure it is securely
connected. Loose or broken pins in the cable connector could cause an improper connection.
Connect the TV unit to another video source or use another TVs to make sure the video
source was not causing the problem.
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising