LIT1336 IT-A25 SERIES AMPS MANUAL D5.indd

LIT1336 IT-A25 SERIES AMPS MANUAL D5.indd
IT-A25 SERIES
AUDIO AMPLIFIERS
(COVERS MODELS IT-A25-M70 AND IT-A25-S8)
INSTALLATION AND OPERATING GUIDE
G
43949
LIT1336 D5
LI
PROPRIETARY INFORMATION
All information in this manual is proprietary to and the
property of FSR inc. This publication is protected by the Federal
Copyright Law, with all rights reserved. No part of this document
may be reproduced, transcribed, or transmitted, in any form or by
any means, without prior explicit written permission from FSR
Inc.
Operators Safety Summary
The general safety information in this summary is for operating
personnel.
Read Instructions Read and understand all safety and operating
instructions before using this equipment. Keep the instructions
handy.
Do Not Remove Covers or Panels There are no user-serviceable
parts within the unit. Removal of the top cover will expose
dangerous voltages. To avoid personal injury, do not remove the
top cover. Do not operate the unit without the cover installed.
Power Source This product is intended to operate from the
specified wall plug-in transformer. Do not use any other power
source.
Use the Proper Power Cord Use only the power cord and
connector specified for your product. Use only a power cord that is
in good condition. Refer cord and connector changes to qualified
service personnel.
Do Not Operate in Explosive Atmospheres To avoid explosion,
do not operate this product in an explosive atmosphere.
2
INTRODUCTION
The IT-A25 Series Amplifiers are the latest addition to FSR’s
Intellitools family. They are designed to deliver great performance
and versatility at an affordable price. Perfect for small venue audio
power applications.
Both models support Pro and consumer audio input levels; The ITA25-M70 Mono Amp provides either a 4-8 ohm speaker output or
a 70 V line output at 25W RMS. The IT-A25 Stereo Amp delivers
a 25W output at 8 ohms and can be bridged to drive a 4 ohm load
at 50 watts.
FEATURES
• Signal Sense trigger for sleep & wake up
• Music and alarm muting capability
• Optional mounts available
• External Power Supply included
• Clean full-range power
APPLICATIONS
• Boardrooms • Houses of Worship• Control Rooms
• Classrooms• Staging and Rental •Libraries
ACCESSORIES
• RK-1 Rack mounting kit
• RK-2 Rack mounting shelf
3
INSTALLATION AND OPERATION
Mount the units as appropriate for the particular installation.
There are #6-32` tapped holes on the top and bottom of the IT-A25
series housings for mounting. Use #6-32 screws that protrude through
no longer than 1/2". There are also rack kits available from FSR for
mounting in a standard 19” rack mount. See “accessories” section for
FSR part numbers and ordering information.
FRONT PANEL LED STATUS INDICATION
On/Standby: Green indicates the
amplifier is active.
ON OFF STANDBY
CLIP
Amber indicates the amplifier is
powered, but in Standby mode
drawing minimal current.
When lit this led indicates the
amplifier is approaching the onset of
clipping.
4
REAR PANEL
Mute Switch Input:
Provide a dry contact or low leakage open collector closure to
mute the amplifier. No connection, or an open circuit provides
for normal operation. The IT-A25 amplifier provides pop-free
transitions in and out of mute mode.
Audio Input:
NOTE: See Option DIP Switch table for proper settings and additional
information.
Connect a balanced or unbalanced audio source to this point.
Unbalanced signals should be connected between “Hi” and “Lo.”
For IT-A25-M70 only:
Connect mono sources to the LEFT audio input terminals
For IT-A25-S8 only:
Connect mono sources to the RIGHT or LEFT audio input terminals.
Master Gain control:
Provides a wide range volume control to adapt to audio source. CW
screwdriver or finger adjust to increase gain.
Audio Out:
For IT-A25-M70 only:
Provides a choice of either 4-8 ohm or 70 volt mono output for
flexibility in interfacing to the room speakers. Connections should be
made to only one output type in a particular installation.
For IT-A25-S8 only:
Provides connection to 4-8 ohm stereo speakers. Outputs may be
bridged (connect + to + and connect - to - When bridging, be sure to
set front panel switch 2 to “mono” mode) to double the output power.
Use 4 ohm speaker, or parallel combination of 8 ohm speaker to
achieve full power when bridging outputs.
Power Input:
Connect to supplied 24 volt external power supply.
5
OPTION DIP SWITCHES
Down=ON=Auto Power-down function
enabled,
AUTO POWER-DOWN
SWITCH 1
UP=OFF=Auto Power-down function
disabled. This switch is used to override
the Auto Power-down feature of the
amplifier and unconditionally force the
amplifier to the on state.
Down=Stereo, Up=Mono. When in Mono
mode, the Left and Right audio inputs are
actively summed together and fed to both
the Left and Right output channels.
MONO/STEREO
SWITCH 2
When in stereo mode, Left and Right
inputs are independent.
NOTE: The IT-A25-M70 mono version of
the product requires this switch to be set to
mono mode when using stereo sources.
When operating the IT-A25-S8 in bridged
output mode, this switch should also be set
to mono mode.
Up=Professional Audio input levels,
Down=Consumer Audio input levels.
INPUT GAIN
SWITCH 3
When down, this switch provides an
additional 12 dB of input boost to
accommodate the lower signal levels of
consumer electronic equipment.
When up, this switch accommodates
the higher signal levels provided by
professional AV mixers.
Up= +12dB,
OUTPUT BOOST
SWITCH 4
Down= Unity. When up, this switch
provides an additional 12 dB of gain to
provide additional flexibility.
6
AUDIO PINOUT
7
DIMENSIONS
Depth is 6.75” on both models. Allow clearance for connectors and cables.
8
TECHNICAL SPECIFICATIONS
AUDIO INPUT
IT-A25-M70
IT-A25-S8
Number of Inputs
1, Stereo balanced
Connector
5 position pluggable screw terminal
Maximum Input Level
7 Vrms, +16.9dBV balanced/unbalanced
Input Impedance
20kȍ balanced/unbalanced
Input Signal Detection
Threshold
(for Auto Power Down)
10mVrms, -40dBV
AUDIO OUTPUT
IT-A25-M70
IT-A25-S8
Connector
2 position pluggable screw
terminal
4 position pluggable screw
terminal
Power Output
25Wrms @ 70V
25Wrms @ 4 to 8ȍ
25Wrms x 2 @ 4 to 8ȍ
Signal Output
Mono
Stereo, 2 Mono, Bridgeable in
Mono mode
Load Impedance
4 to 8ȍ or 70V
4 to 8ȍ
THD+Noise
0.1% @ 10KHz, 10W 70V
Output
0.5% @ 1KHz, 25W 8ȍ
Frequency Response
100Hz-20KHz, +0, -1dB;
-3dB @ 50Hz
20Hz-20kHz, +0, -1dB
Signal to Noise Ratio
>97dB @ 70V,
100Hz-20Khz, un-weighted
>90dB @ 25W 8ȍ,
20Hz-20KHz, Un-weighted
CONTROL ADJUSTMENTS
IT-A25-M70
IT-A25-S8
x
x
x
x
Control Switch
Remote Muting Input
Dry contact closure required
9
Master Volume
FEATURES
Auto Power Down
Stereo/Mono (L+R sum)
Pro/Consumer (+12dB)
Unity/+12dB Gain
IT-A25-M70
9
IT-A25-S8
Auto Power Down
9
9
Clip Indicator
9
9
Output short circuit
protection
9
9
9
Bridgeable Output
Power up/down click and
Pop suppressor
9
9
9
POWER REQUIREMENTS
IT-A25-M70
IT-A25-S8
100-240VAC
100-240VAC
Power input requirement
24V DC @ 1.2A
24V DC @ 2.4A
Power [email protected] Full
Output
d 28W
d 58W
External power supply
d 1W
Standby Power
d 3.5W
Idle Power
Model
Dimensions (inches)
Shipping
weight
lbs.
MECHANICAL
2.5
IT-A25-M70
6.75 x 4.22 x 1.59
1.5
IT-A25-S8
GENERAL
IT-A25-M70
IT-A25-S8
x Power On
x Standby
x Clip Indicator
LED Indicators
Operating Temperature
0° C to 40° C
Cooling
Convection cooled
Enclosure Material
Metal
Turn on time from Auto
Power Down (typical)
25ms
Time to enter Mute state
(typical)
<1ms
Time to exit Mute state
(typical)
30ms
Amplifier Class
D
10
REGULATORY COMPLIANCE
The Power Adapter has been tested for compliance with: UL, CSA and CE.
WARRANTY POLICY
This product is warranted against failures due to defective parts or faulty workmanship for a period of
three years after delivery to the original owner. During this period, FSR will make any necessary repairs
or replace the unit without charge for parts or labor. Shipping charges to the factory or repair station must
be prepaid by the owner, return-shipping charges, via UPS / FedEx ground, will be paid by FSR.
This warranty applies only to the original owner and is not transferable. In addition, it does not apply
to repairs done by other than the FSR factory or Authorized Repair Stations.
This warranty shall be cancelable by FSR at its sole discretion if the unit has been
subjected to physical abuse or has been modified in any way without written authorization from FSR.
FSR’s liability under this warranty is limited to repair or replacement of the defective unit.
FSR will not be responsible for incidental or consequential damages resulting from the use or misuse
of its products. Some states do not allow the exclusion of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Warranty claims should be accompanied by a copy of the original purchase invoice
showing the purchase date (if a Warranty Registration Card was mailed in at the time of purchase, this
is not necessary). Before returning any equipment for repair, please read the important information
on service below.
SERVICE
Before returning any equipment for repair, please be sure that it is adequately packed and cushioned
against damage in shipment, and that it is insured. We suggest that you save the original packaging and
use it to ship the product for servicing. Also, please enclose a note giving your name, address, phone
number and a description of the problem.
NOTE: All equipment being returned for repair must have a Return Authorization (RMA)
Number. To get a RMA Number, please call:
FSR Service Department (973-785-4347).
Please display your RMA Number prominently on the front of all packages.
Contact Information:
FSR Inc.
244 Bergen Boulevard,
Woodland Park, NJ 07424
Tel: (973) 785-4347 · Fax: (973) 785-4207
E-Mail: [email protected] · Web: http://www.fsrinc.com
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement