- No category
advertisement
Axon Flex 2 Quick Start Guide
English
Hardware Quick Reference
Axon Flex 2 controller
Microphone
Speaker
Cable Connection Port
Also for data transfer and recharge with PC or Axon Dock
Function LED
Operation LED
Camera cable
Slide Lock
Holds cable to controller
Power Switch
Red = On/Buffering
Speaker
Function Button
Mute or add marker
EVENT Button
Double-press = Start record
Hold 3 seconds = Stop record
Axon Flex 2 camera
Also available:
USB C to A Sync cable
Battery LED
Green = 41–100%
Yellow = 20–40%
Red = Less than 20%
Battery Status Button
Push to show status of battery
Read, understand, and follow all current instructions, warnings, and relevant Axon training materials before using any Axon system. The most up-to-date warnings and instructions are available at www.axon.com.
Before using an Axon Flex 2 system, ensure it is fully charged, and connect it to Evidence.com via the Axon Dock or Evidence Sync software to ensure it is properly configured. See Controller Battery LED and Recharging the Battery and Uploading Data for more information. If the battery’s charge is ever depleted, recharge and reconnect the connect the system again.
Recording
2 To record, quickly double-press the EVENT button.
The Axon Flex 2 system has 2 operating modes. The default mode, or
BUFFERING mode, provides pre-event buffering to capture activities that occur before you activate the EVENT (recording) mode.
1 Turn the system on. Move the ON/OFF switch to the ON position.
• The system now records audio as well as video.
• The system will beep twice to let you know that recording started.
The 2 beeps will repeat every 2 minutes (if the system is muted, there will be no audio notifications).
• The operation LED will blink red.
• The camera takes a few seconds to boot up and be ready to record
(the red area under the switch will be exposed with the switch moved to the ON position).
3 To stop recording and return to BUFFERING mode, press and hold the
EVENT button for at least 3 seconds until there is a long, audible beep.
Solid red
Boot up mode
Blinking green
BUFFERING mode EVENT button
Blinking red – recording mode
• The operation LED will be solid red and then transition to blinking green when the system goes into BUFFERING mode.
• The system will go into BUFFERING mode after the boot up sequence.
With default settings, the BUFFERING mode holds the previous 30 seconds of video (NO AUDIO) leading up to the beginning of a recording.
Controller Operation LED
The controller’s operation LED displays the system’s current operating mode.
Operating Mode
EVENT
BUFFERING
Controller LED
Blinking red
Blinking green
Recovering interrupted video*
Booting up/powering down
Blinking red
Solid red
Error state** Solid red
Cable disconnect Blinking yellow
* When the function LED also is blinking red. If little video was interrupted, the function LED will blink only briefly.
** When the Function LED also is solid red.
Controller Function LED
The Axon Flex 2 controller’s function LED displays when certain functions are enabled.
Because the system does not capture audio in BUFFERING mode, the first 30 seconds of a recorded event will be video-only (depending on your agency’s settings). BUFFERING mode starts only after the camera boots up. The system does not record when the Axon Flex 2 controller is turned off.
Controller Battery LED
The controller’s battery LED displays the battery’s remaining capacity, when the device is being used or when charging.
Battery LED Battery Capacity
Battery capacity is 41–100 percent
Green
Battery capacity is 20–40 percent Yellow
Battery capacity is less than 20 percent
Red
Mute
Function Enabled
Camera error***
Function LED
Blinking blue
Solid red
Pairing mode Blinking green
*** Use the power switch to turn the camera off and on.
Notifications
Operating Mode Audio
Powering on or off
Recording an event
One beep
Two beeps (every
2 minutes)
Press the battery button while the camera is recording Two beeps
The device is ending an event and returning to BUFFERING mode
One long beep
The battery is at 20% capacity or lower
Cable disconnect (the camera will shut down)
Camera memory is full (the camera will not record)
Four quick beeps
(every 5 minutes)
Three beeps
Three beeps
Vibration
Once
Twice (every 2 minutes)
None
Once, long duration
Four times, quickly
(every 5 minutes)
Six times
Recharging the Battery and Uploading Data
If you do not have an Axon Dock, upload video with a Windows compatible computer using Evidence Sync: axon.com/syncdownload.
1 Ensure the controller is off. Insert the camera and controller into the
Axon Dock as shown.
The Axon Dock automatically uploads the data from the camera to Evidence.com and recharges the controller battery. When a video uploads successfully to Evidence.com, that video is removed from the camera.
(The camera must be registered to your Evidence.com account.)
2 At the beginning of the next shift, ensure that your camera (if one has been assigned to you) displays with a green LED before removing it from the Axon Dock.
Three times
Five times, quickly
(every 20 seconds)
Camera Upload Status LED
When you plug your camera into the Axon Dock, the LED on the camera displays the system’s status.
Device Status
Initial connection (momentary)
In queue awaiting upload
Device ready (all videos uploaded successfully) and fully charged
Device not assigned, agency mismatch, camera set in the offline mode, or device error
Uploading data
Firmware update, internal battery charging, extremely low battery, or memory full
Transfer error, device re-trying to transfer
Network error
Axon Dock has no communication with the camera. Contact Axon customer service.
Camera LED
Solid red (for 20 seconds or fewer)
Solid yellow
Solid green
Blinking red
Blinking yellow
Blinking red and yellow – DO NOT remove the camera from the Axon
Dock
Blinking green and yellow
Blinking red, yellow, and then green (cycling all colors)
LED off
Using Axon View
The Axon View application enables you to replay video and add metadata
(GPS, title, ID, and category) to your videos using a smart phone or multimedia player.
1 Using your smart device, download the Axon View application from the Google Play store or the iTunes App
Store. Search Axon View.
2 On your smart device, open the Axon View application and follow the onscreen instructions.
Note: All data is stored on the Axon camera. No videos are stored on your smart device
Pairing an Axon Flex 2 Camera with a Smart Device
1 With the camera connected to the controller, turn on the Axon Flex 2 controller.
2 Wait until the Function LED is not lit anymore.
3 Hold down the
Function and
EVENT buttons for
5 seconds.
For more information, see the Axon Flex 2 System User Manual, Axon Dock
Quick Start Guide, Axon View for Android Devices User Manual, or Axon View
for iOS Devices User Manual, available at www.axon.com, axon.com/au/, axon.com/uk.
4 Wait until you hear 4 beeps.
The Function LED on the controller and the camera
LED will blink green.
5 On your smart device, follow the onscreen instructions.
Android and Google Play are trademarks of Google, Inc., Bluetooth is a trademark of the Bluetooth SIG, iTunes is a trademark of Apple,
Inc., and IOS is a trademark of Cisco Systems, Inc.
, AXON, Axon, Axon Dock, Axon Flex 2, Evidence.com, and Evidence Sync are trademarks of Axon Enterprise, Inc., some of which are registered in the US and other countries. For more information, visit www.axon.com/legal.
All rights reserved. © 2017 Axon Enterprise, Inc.
MPC0251 Rev: E
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project