CD/Cassette/Radio Portable Player - Groov-e

CD/Cassette/Radio Portable Player - Groov-e
GV-PS823
CD/Cassette/Radio
Portable Player
INSTRUCTION MANUAL
WARNING
1. WARNING:Please refer the information on exterior bottom enclosure for electrical and safety
information before installing or operating the apparatus.
2. WARNING:To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on apparatus.
3. WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat
such as sunshine, fire or the like.
4. WARNING: The mains plug is used as disconnect device, the disconnect device shall remain
readily operable.
5.
6.
Invisible laser radiation when open and interlocks defeated. Avoid exposure to beam of laser.
Correct Disposal of this product. This marking indicates that this product should not be disposed
with other household wastes throughout the EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable
reuse of material resources. To return your used device, please use the return and collection systems
or contact the retailer where the product was purchased. They can take this product for environmental
safe recycling.
7. No naked flame sources, such as lighted candles, should be placed on the apparatus.
8. Attention should be drawn to environmental aspects of battery disposal.
9. Use of the apparatus in moderate climates.
10. The rating and marking information are located at the back of the unit.
11. Excessive sound pressure from earphone and headphones can cause hearing loss.
12. The mains plug of unit should be obstructed or should be easily accessed during intended use.
13. To be completely disconnect the power input, the mains plug of apparatus shall be disconnected from the mains.
14.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way
that it does not require a safety connection to electrical earth.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
E-1
WARNING
TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : SHOCK HAZARD-DO NOT OPEN
LIGHTING FLASH WITH ARROWHEAD SYMBOL -
EXCLAMATION POINT - within an equilateral triangle,
within an equilateral triangle, is intended to alert the
is used to indicate that a specific component shall be
user to the presence of uninsulated dangerous
replaced only by the component specified in that
voltage within the products enclosure that may be of
documentation for safety reason.
sufficient magnitude to constitude a risk of electric
shock to persons.
The following label has been affixed to the unit, listing the proper procedure for working with the laser beam:
CLASS 1 LASER PRODUCT LABEL CLASS 1 LASER PRODUCT
KLASS 1 LASER APPARAT
LUOKEN 1 LAISERLAITE
KLASSE 1 LASER PRODUKT
This label is attached to the place as illustrated to inform that the
apparatus contains a laser component.
WARNING LABEL INFORMING OF RADIATION This label is placed inside the unit. As shown in the illustration. To
warn against further measures on the unit. The equipment contains
a laser radiating laser rays according to the limit of laser product of
class 1.
E-2
SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instruction should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating instructions should be followed.
5. WATER AND MOISTURE - The appliance should not be used near water, for example, near a bathtub, washbowl,
kitchen sink, laundrytub, swimming pool or in a wet basement.
6. VENTILATION - The appliance should be situated so that its location or position does not interfere with its proper
ventilation. Do not place on bed, sofa, rug or similar surface that may block the ventilation openings, in a built-in
installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
7. HEAT - The appliance should be situated away from heat sources such as radiators, stoves, or other appliances
(including amplifiers) that produce heat.
8. POWER SOURCE - The appliance should be connected to power supply only of the type described in the
operating instructions or as marked on the appliance.
9. POWER CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them.
10. POWER LINES - An outdoor antenna should be located away from power lines.
11. OBJECT and LIQUID ENTRY - Care should be taken so that objects do not fall and liquids are not spilled into
the enclosure through openings.
12. ESD WARNING - The display does not function properly or no reaction to operation of any the control may due
to the electrostatic discharge. Switch off and unplug the set. Reconnect after a few seconds.
13. DAMAGE REQUIRING SERVICE - The appliance should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen into, or liquid has been spilled into the appliance enclosure.
c. The appliance has been exposed to rain.
d. The appliance has been dropped, or the enclosure damaged.
e. The appliance does not appear to operate normally.
14. SERVICING - The user should not attempt to service the appliance beyond that described in the user operating
instructions. All other servicing should be referred to qualified service personnel.
Notes:
a. Dirty or scratched CD may cause a skipping problem. Clean or replace the CD.
b. If an error display or malfunction occurs, disconncet the AC cord and remove all the batteries. Then turn the power
back on.
BEFORE OPERATION
Notes: CONCERNING COMPACT DISCS.
Since dirty, damaged or warped discs may damage the appliance, care should be taken of the followings items:
a. Usable compact discs. Use only compact disc with the mark shown below.
b. CD compact disc only with digital audio signals.
E-3
POWER SOURCES
to AC IN
to a wall outlet
Insert 6 x “C” size batteries (not included)
into the battery compartment
AC POWER
You can power your portable system by plugging the detachable AC power cord into the AC inlet at
the back of the unit and into a wall AC power outlet. Check that the rated voltage of your appliance
matches your local voltage. Make sure that the AC power cord is fully inserted into the appliance.
Power Source
AC 230V ~ 50Hz, DC : 9 V
BATTERY POWER
Insert 6 x “C” size batteries into the battery compartment. Be sure that the batteries are inserted
correctly to avoid damage to the appliance. Always remove the batteries when appliance will not be
used for a long period of time, as this will cause leakage to the batteries and subsequently damage
to your set.
Notes:
- Use batteries of the same type. Never use different types of batteries together.
- To use the appliance with batteries, disconnect the AC power cord from it.
E-4
LOCATION OF CONTROL
AUX IN
HEADPHONE SOCKET
FM ANTENNA
BAND
SELECTOR
FUNCTION
SELECTOR
TUNING
CONTROL
VOLUME
CONTROL
CD DOOR
OPEN / CLOSE
TAPE BUTTONS - PAUSE, STOP / EJECT, FAST FORWARD, REWIND, PLAY, RECORD
LED DISPLAY
POWER
INDICATOR
FM STEREO
INDICATOR
SKIP +
PLAY / PAUSE
SKIP -
STOP
PROGRAM
REPEAT
CASSETTE DOOR
E-5
RADIO OPERATION
GENERAL OPERATION
1.
2.
3.
4.
Set the “FUNCTION” selector to “RADIO” mode.
Select desired band by using the “BAND” selector.
Adjust radio frequency to your desired station by using the “TUNING” control.
Adjust the “VOLUME” control to the desired level.
FM / FM-STEREO RECEPTION
- Set the “BAND” selector to FM mode for MONO reception.
- Set the “BAND” selector to FM ST. mode for FM STEREO reception. The Stereo indicator light up
to show FM ST. mode.
FOR BETTER RECEPTION
- Reorient the antenna for better reception.
- Reorient the appliance to get better AM reception.
E-6
TAPE OPERATION
GENERAL OPERATION
PAUSE
Press to stop playing tape operation temporarily.
Press again to resume tape operation.
STOP / EJECT
Press to stop tape operations.
Press again to open the cassette door after the tape spools stop turning.
FAST FORWARD
REWIND
PLAY
RECORD
&
Press to start rapid tape winding either forward or reverse direction.
Press to start playing tape.
Press it together with “PLAY” button to start recording.
PLAYBACK
1.
2.
3.
4.
5.
6.
7.
Set the “FUNCTION” selector to “TAPE” mode.
Press the “STOP / EJECT” button to open the cassette door and insert your tape.
Close the cassette door.
Press the “PLAY” button to start playing tape.
Adjust the “VOLUME” control to the desired level.
Press the “PAUSE” button when you want to stop playing tape operation temporarily.
Press the “STOP / EJECT” button when finished.
RECORDING
1. Press the “STOP / EJECT” button to open the cassette door and insert a blank tape.
2. Select the source you want to record.
To record from radio - Set the “FUNCTION” selector to “RADIO” mode and adjust the desired station.
To record from CD - Place a disc on the CD compartment. Set the “FUNCTION” selector to
“CD” mode and select the desired track.
3. Press the “RECORD” button together with the “PLAY” button to start recording.
4. Press the “STOP / EJECT” button when finished.
E-7
CD OPERATION
GENERAL OPERATION
PLAY / PAUSE
Press to start playing CD disc.
Press again to stop playing CD operation temporarily.
Press again to resume playback.
SKIP +
SKIP -
Press to go to the next track or back to the previous track.
Press and hold while playing until you find the point of the sound.
&
STOP
Press to stop all CD operation.
AUTOMATIC STANDBY SWITCHING
To comply with the “ERP2 (Energy Related Products)” Ecodesign Directive (2009/125/EG), its
ultimate aim is to reduce the energy consumption of energy-using products; the device automatically
switches to standby after approx. 10 minutes without a signal. In order to use the device again,
switch the device off and then on again.
PLAYBACK
1.
2.
3.
4.
5.
6.
7.
8.
Set the “FUNCTION” selector to “CD” mode.
Open the CD door and place a CD disc with the label up in the CD compartment.
Close the CD door.
Focus search is performed if disc is inside. Total number of tracks is read and appears on the display.
Press the “PLAY / PAUSE” button to start playing CD disc.
Adjust the “VOLUME” control to the desired level.
Press the “PLAY / PAUSE” button again when you want to stop playback temporarily.
Press the “STOP” button when finished.
E-8
CD OPERATION
PROGRAM
Up to 20 tracks can be programmed for disc play in any order.
Be sure to press the “STOP” button before use.
1. Press the “PROGRAM” button, the display will show “01” and flash.
2. Select desired track by using the “SKIP +” or “SKIP -” button.
3. Press the “PROGRAM” button again to confirm desired track into the program memory.
4. Repeat step 2 and 3 to enter additional tracks into the program memory.
5. When all the desired tracks have been programmed. Press the “PLAY / PAUSE” button to play the
disc in the order you have programmed.
6. Press the “STOP” button twice to terminate programmed play and the program indicator will turn off.
REPEAT
Press the “REPEAT” button before or during playing CD, a single track or all the tracks can be repeated.
Each press switches the repeat mode as follows:
1 - REPEAT 1 ( The repeat indicator is flashing. )
2 - REPEAT ALL ( The repeat indicator is steadily on. )
3 - NORMAL PLAYBACK
E-9
REPEAT 1
REPEAT ALL
NORMAL
PLAYBACK
OTHER FEATURES
AUX IN
Listen to external audio device by connecting it to the appliance through the 3.5mm AUX IN jack.
1. Set FUNCTION switch to TAPE.
2. Use one male to male stereo cable (not included) to connect phone jack of any external audio
device to AUX IN jack of the appliance.
3. Press PLAY key of cassette.
4. Start playback on the external audio device. Adjust the volume on the external device (Do not set
the volume too high to avoid distortion). You may also adjust the volume on the appliance.
5. To control playback function, use the controls on the external audio device.
6. Press STOP key of cassette on the appliance while you stop listening to the external audio device
through AUX IN.
HEADPHONE SOCKET
Connect your 3.5mm headphone. Use the volume control to adject the sound level for the headphone.
SPEAKERS
Output Power: 2 x 1.2 W
Unit J, Braintree Road
Ruislip HA4 0EJ
www.groov-e.co.uk
Environmental Protection
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling
advice.
E-10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement