advertisement
INSTALLATION INSTRUCTIONS
Model: MIDBAY
Fixture Family: MIDBAY
Document Description: Installation Instructions for
MIDBAY Series Luminaires
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
LENS ATTACHMENT, JBOX MOUNTING AND ACCESS
FIXTURE JBOX
MOUNTING
SCREWS
LENS STOP
FIXTURE
NOTCHED AREA
1. ANGLE FIXTURE JBOX THROUGH NOTCHED
AREA IN HOUSING AND SLIDE INTO POSITION
SO THAT JBOX MOUNTING FLANGE IS UNDER
HOUSING EDGE AND SCREW HOLES ARE ALIGNED.
2. ATTACH WITH (4) SCREWS PROVIDED THROUGH
HOUSING INTO JBOX FROM TOP AS SHOWN.
3. REMOVE ACCESS PLATE FOR MOUNTING
AND WIRING BY LOOSENING SCREWS (2),
THEN TURN AND SLIDE PLATE TO THE SIDE.
4. MOUNT AND WIRE PER PAGE 2 AND 3.
5. LENS IS ATTACHED BY LIFTING INTO FIXTURE
AND SECURING WITH ATTACHMENT NUT
AGAINST LENS STOPS.
BRACKET
MOUNTING
SCREWS
WIREGUARD
BRACKET
LENS
WIREGUARD
MOUNTING
NUT
ACCESS
PLATE
LENS ATTACHMENT
NUT
FIXTURE
MOUNTING
LEG
WIREGUARD
WIREGUARD MOUNTING
1. INSTALL ONE NUT ONTO EACH MOUNTING
LEG OF WIREGUARD (3 PLACES). TURN NUT TO
THE END OF THE THREADS.
2. ASSEMBLE WIREGUARD BRACKETS TO
FIXTURE BY INSERTING INTO SLOT ON HOUSING
AND ATTACHING WITH (2) MOUNTING SCREWS.
3. LIFT WIREGUARD AROUND FIXTURE AND INSERT
MOUNTING LEGS THROUGH HOLES IN BRACKET.
ATTACH WITH 3 ADDITIONAL NUTS.
!
•
When using electrical equipment, basic safety precautions should always be followed, including the following:
•
•
•
•
Read all instructions carefully installing and save for future use.
Make sure all connections are in accordance with the National Electrical Code and local regulations.
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
Service should be performed by qualified personnel.
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
INSTALLATION INSTRUCTIONS
Model: MIDBAY
Fixture Family: MIDBAY
Document Description: Installation Instructions for
MIDBAY Series Luminaires
JBOX (BY
OTHERS)
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
FIXTURE JBOX
SURFACE MOUNTING
1. ASSEMBLE FIXTURE JBOX TO FIXTURE WITH
SCREWS (4) PROVIDED. SEE PAGE 1 FOR
JBOX MOUNTING AND JBOX ACCESS INSIDE
FIXTURE. ASSEMBLE CLOSURE PLATE TO FIXTURE
JBOX WITH SCREWS (2) PROVIDED WHEN USING
A 4" OCTAGONAL BOX.
2. MAKE ELECTRICAL CONNECTIONS PER CODE.
JBOX
(BY OTHERS)
JBOX PLATE &
HOOK OPTION
(ORDERED
SEPARATE)
LOOP
CONNECTOR
FIXTURE JBOX
HOOK MOUNTING
1. ASSEMBLE FIXTURE JBOX TO FIXTURE WITH
SCREWS (4) PROVIDED. SEE PAGE 1 FOR
JBOX MOUNTING AND JBOX ACCESS INSIDE
FIXTURE. MAKE ELECTRICAL CONNECTION AT
FIXTURE.
2. ASSEMBLE LOOP CONNECTOR TO EYEBOLTS AT
FIXTURE AND JBOX PLATE, CLOSE LOOP AND
ATTACH TO STRUCTURE. (JPH OPTION CAN BE
ORDERED SEPARATE FOR ATTACHMENT TO
JBOX)
3. MAKE ELECTRICAL CONNECTIONS PER CODE.
JBOX ( BY OTHERS)
LOOPED/CRIMPED
CABLE ENDS
CABLE MOUNTING
DETAIL
CHAIN
MOUNTING
DETAIL
CABLE / CHAIN MOUNTING
JBOX PLATE &
HOOK OPTION
(ORDERED
SEPARATE)
1. ASSEMBLE FIXTURE JBOX TO FIXTURE WITH
SCREWS (4) PROVIDED. SEE PAGE 1 FOR
JBOX MOUNTING AND JBOX ACCESS INSIDE
FIXTURE. MAKE ELECTRICAL CONNECTION AT
FIXTURE.
CABLE
ASSEMBLY
2. LOOP CABLE THRU EYEBOLTS (3) ON FIXTURE
AND ATTACH CABLE GRIPPER TO CABLE PER
INSTRUCTIONS IN CABLE ASSEMBLY PACKAGE.
FOR CHAIN MOUNTING, USE (3) LOOP
CONNECTORS TO ATTACH CHAIN TO FIXTURE
EYEBOLTS. (SEE DETAILS).
FIXTURE JBOX
3. ASSEMBLE ALL CABLES OR CHAINS TO LOOP
CONNECTOR, ATTACH TO STRUCTURE AND
CLOSE LOOP. (JPH OPTION CAN BE ORDERED
SEPARATE FOR ATTACHMENT TO JBOX)
4. MAKE ELECTRICAL CONNECTIONS PER CODE.
5. IF DESIRED, ROUTE CORD ALONG THE CABLE/
CHAIN AND SECURE EVERY 6".
LOOP CONNECTOR
!
•
When using electrical equipment, basic safety precautions should always be followed, including the following:
•
•
•
•
Read all instructions carefully installing and save for future use.
Make sure all connections are in accordance with the National Electrical Code and local regulations.
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
Service should be performed by qualified personnel.
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
INSTALLATION INSTRUCTIONS
Model: MIDBAY
Fixture Family: MIDBAY
Document Description: Installation Instructions for
MIDBAY Series Luminaires
JBOX
(BY OTHERS)
THREADED RIGID
CONDUIT
(BY OTHERS)
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
SQUARE OR
ROUND SWIVEL
PLATE OPTION
(ORDERED
SEPARATE)
STEM MOUNTING
1. ASSEMBLE FIXTURE JBOX TO FIXTURE WITH
SCREWS (4) PROVIDED. SEE PAGE 1 FOR
JBOX MOUNTING.
2. ATTACH IMC THREADED CONDUIT (BY OTHERS)
TO FIXTURE THROUGH FIXTURE JBOX. ATTACH
TO JBOX (BY OTHERS). SEE PAGE 1 FOR JBOX
ACCESS INSIDE FIXTURE.(SKS OR SKR SWIVEL KIT
OPTION CAN BE ORDERED SEPARATE FOR
ATTACHMENT TO JBOX) *CAUTION: LOCKTITE
ADHESIVE NEEDS TO APPLIED TO STEM THREADS
TO PREVENT LOOSENING OF STEM.
FIXTURE JBOX
3. MAKE ELECTRICAL CONNECTIONS PER CODE.
JBOX
(BY OTHERS)
CANOPY
FLANGE
COUPLER
RUNNING
THREAD
MOUNTING
BRACKET
SWIVEL
BALL
FIXTURE JBOX
PHA OPTION STEM MOUNTING
1. ASSEMBLE FIXTURE JBOX TO FIXTURE WITH
SCREWS (4) PROVIDED. SEE PAGE 1 FOR
JBOX MOUNTING AND JBOX ACCESS INSIDE
FIXTURE.
2. INSERT FLANGE COUPLER THROUGH HOLE IN
FIXTURE JBOX FROM BOTTOM OF FIXTURE,
ATTACH WITH SCREWS (2) PROVIDED.
3. THREAD STEM INTO COUPLER AT FIXTURE AND
TIGHTEN SET SCREW.
4. SLIDE CANOPY DOWN OVER STEM AND THREAD
SWIVEL BALL ONTO STEM. *CAUTION: LOCKTITE
ADHESIVE NEEDS TO APPLIED TO STEM THREADS
TO PREVENT LOOSENING OF STEM.
5. ATTACH MOUNTING BRACKET TO JBOX (BY
OTHERS)
6. LIFT FIXTURE ASSEMBLY AND INSERT SWIVEL BALL
INTO MOUNITNG BRACKET AND ALIGN NOTCHES,
ATTACH CANOPY TO MOUNTING BRACKET.
7. MAKE ELECTRICAL CONNECTIONS PER CODE.
WIREWAY
COVER
CABLE
ADJUSTER
LRS OPTION ASSEMBLY
1. SEE PAGE 1 FOR FOR REMOVAL OF WIREWAY
COVER.
2. INSERT CABLE ASSEMBLY THROUGH LENS AND
RUNNING THREAD ON WIREWAY COVER.
3. INSERT CABLE ASSEMBLY THROUGH HOLE IN
LAMP PLATE AND THROUGH HOLE IN CABLE
ADJUSTER, TIGHTEN SCREW ONTO CABLE.
LRS CABLE
!
•
When using electrical equipment, basic safety precautions should always be followed, including the following:
•
•
•
•
Read all instructions carefully installing and save for future use.
Make sure all connections are in accordance with the National Electrical Code and local regulations.
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
Service should be performed by qualified personnel.
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement