User Manual Cyclone

User Manual Cyclone
材质:封面封底128G双铜 + 单色印刷
内页臻品上质80g高白纸 2个小号骑马钉
大约16页, 尺寸W 105 x H 75mm
1. Outdoor Wireless speaker overview
2. Three playing modes
For a Better Experience
Power On/ Off
TF mode: need to insert a TF card (Please buy separately)
There are three playing modes. You can short press M button to switch among the three
Note: The speaker needs 30-40s to read card before streaming audio. Please wait for a while
modes.
after power it on.
Volume up/ Next track
When three modes are all available, the first priority is Aux in mode, and the second priority
MICRO SD
User Manual
DC/5V
Outdoor wireless speaker
Cyclone
AUX
is TF mode. If no TF card inserted nor Aux in, it will enter Bluetooth mode directly.
Aux in mode: connect by 3.5mm audio cable
Bluetooth mode: pair and connect through Bluetooth
Mode switch
Indicator
SD
3.5mm audio cable
MICRO
DC/5V
Multifunction button
Volume down/ Previous track
Micro USB charging cable
www.avantree.com
3. Power On / Off
Power ON: Press and hold POWER button for 2–3s, and you will hear a tone with
the according mode to indicate it has switched on.
Note: It will automatically turn off if not connected to any device in Bluetooth mode
or paused in TF mode over 10 minutes.
3.5 mm audio cable
NOTE: All accessories are also available on avantree.com
-1-
-2-
4. Pair and connect with Bluetooth-enabled devices (with no
TF card inserted nor Aux in)
STEP 1 Get Cyclone into pairing mode - Press and hold the POWER button for 2–3
seconds until you hear a tone with “Bluetooth mode has been on”, and the
LED indicator flashes quickly.
Power OFF:
Press and hold POWER button for 2–3s, and you will hear a two-tone beep to
indicate it has switched off.
-3-
Note: Make sure your PC/notebook is Bluetooth enabled and supports A2DP
profile; otherwise you may need a Bluetooth audio adapter. For details on
how to set up with your PC/notebook, please see support.avantree.com.
Reconnect Bluetooth
Once paired, whenever you turn Cyclone on again it will be automatically
reconnected to the latest device.
STEP 3 Then your phone will get a reception request if you would like to pair with the
speaker.
STEP 4 Tap “Yes”, then your mobile phone will connect with your Cyclone with a
tone of “paired”.
STEP 5 Tap it again to disconnect with a tone of “waiting for pairing”
NOTE: Since the NFC antenna is located in different locations for different phones, it
is helpful to know the location for fast pairing. For details on NFC, see your
phone’s user manual.
5. Connect with NFC enabled mobile phone
STEP 2 Activate Bluetooth on your phone/PC/notebook and select ‘Avantree
Cyclone’.
STEP 3 Once connected, you will hear a tone with “paired” and the LED indicator will
stay blue.
-4-
-5-
6. How to use
Button
-8-
9.Warnnings
This device complies with part 15 of the FCC Rules. Operation is subject to the
condition that this device does not cause harmful interference (1) this device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.Changes or
modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
AUX
-
Charging requirement: You can plug our supplied Micro USB cable to your own USB
charger (wall charger / travel charger / car charger, etc) with 5V / 500Ma -2A. It is
OK to use most mobile phone chargers on the market.
SD
+
When the battery power is low, a tone with “No battery; Please recharge” will come
out every 25S. Please charge the speaker. Otherwise, it will turn off automatically
soon. Please charge the speaker via the Micro USB charging port DC 5V by using
the Micro USB cable. It normally takes about 3.5 hours to fully charge the battery.
The indicator will stay red when charging and will turn off when fully charged.
-7-
MICRO
+
Operation
Press and hold POWER 3s
Press MFB once
Press MFB once
Press and hold MFB 2s
Press and hold MFB 2s
Press MFB once
Press MFB once
Short Press M once
Press and hold “+”
Press and hold “-”
Press “+” once
Press “-” once
DC/5V
M
-6-
7. How to charge
Function
On/Off
Answer a call
End a call
Reject a call
Redial last number
Play music
Pause music
Mode switch
Volume up
Volume down
Next track
Previous track
STEP 1 Turn on your speaker. Make sure NFC function is turned on from your
phone settings and the screen is active and unlocked.
STEP 2 Hold the NFC mobile phone against the NFC zone of the speaker (on the
bottom) until your mobile phone plays an indicate note. (Some phones will
vibrate and some will have a beep sound.)
Micro USB cable
8. Product specifications
•
•
•
•
•
•
•
•
•
•
•
•
BT Version: 3.0, Class 2
Support Bluetooth HSP, HFP, A2DP and AVRCP Profiles
Support mp3, wav format in TF mode
Output power: 5W x 2
Talk time: up to 6 hours
Music time: up to 6 hours
Standby Time: 40 hours
Charge time: About 3.5 hours
Operational range: up to 10 meters
Frequency Responds range: 100Hz ~ 20 kHz
Size: 180mm x 70mm x 70mm
Net Weight: 433g
For more FAQ information, please refer to support.avantree.com
LED charging indicator
-9-
- 10 -
- 11 -
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.If this equipment
does cause harmful interference to radio or television reception, which can be
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should
be installed and operated with minimum distance between 20cm the radiator your
body: Use only the supplied antenna.
- 12 -
- 13 -
For a Better Experience
Dispose of the packaging and
this product in accordance with
the latest provisions.
www.avantree.com
support@avantree.com
FCC ID: 2AITF-BTSPWP400
Z-PKMN-WP400-V1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising