avertX HD80IRM User manual
AvertX HD80IRM is an indoor/outdoor IP dome camera that offers high-definition video surveillance with night vision capabilities. With its compact and weatherproof design, it can be installed in various locations for home or business security. The camera features motion detection, tampering alarm, and remote access through a web browser or mobile app, allowing for real-time monitoring and recording. The HD80IRM provides clear and detailed footage in both day and night conditions, ensuring reliable surveillance around the clock.
Advertisement
Advertisement
HD80IRM
Night Vision HD Indoor/Outdoor IP
Dome Camera
User Manual
HD80IRM: Night Vision HD Indoor/Outdoor IP Dome Camera
Operations Manual
Manual Edition 32336AC – JULY 2014
©2014, AvertX
All Rights Reserved
No part of this document may be reproduced by any means, electronic or mechanical, for any purpose, except as expressed in the Software License Agreement.
AVERTX shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is subject to change without notice.
The information in this publication is provided “as is” without warranty of any kind. The entire risk arising out of the use of this information remains with recipient. In no event shall AVERTX be liable for any direct, consequential, incidental, special, punitive, or other damages whatsoever (including without limitation, damages for loss of business profits, business interruption or loss of business information), even if AVERTX has been advised of the possibility of such damages or whether in an action, contract or tort, including negligence.
This software and documentation are copyrighted. All other rights, including ownership of the software, are reserved to AvertX. AVERTX, and AvertX, are registered trademarks of AVERTX in the United States and elsewhere; Windows is a registered trademarks of Microsoft Corporation. All other brand and product names are trademarks or registered trademarks of the respective owners.
The following words and symbols mark special messages throughout this guide:
WARNING: Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
AVERTX
2
IMPORTANT SAFEGUARDS
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments / Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause hazards, damage product and void warranty.
4. Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only with a mounting device recommended by the manufacturer, or sold with the product. To insure proper mounting, follow the manufacturer's instructions and use only mounting accessories recommended by manufacturer.
5. Power source
This product should be operated only from the type of power source indicated on the marking label.
Precautions
Operating
•
Before using, make sure power supply and others are properly connected.
•
While operating, if any abnormal condition or malfunction is observed, stop using the camera immediately and then contact your local dealer.
Handling
•
Do not disassemble or tamper with parts inside the camera.
•
Do not drop or subject the camera to shock and vibration as this can damage camera.
•
Do not block the cooling holes on the bracket. This camera has a cooling fan inside the housing. Blocking the cooling holes will cause heat to build up and cause malfunction.
•
Care must be taken when you clean the clear dome cover.
Scratches and dust will ruin the image quality of your camera.
Do not use strong or abrasive detergents when cleaning the camera body. Use a dry cloth to clean the camera when it is dirty. In case the dirt is hard to remove, use a mild detergent and wipe the camera gently.
Installation and Storage
•
Do not install the camera in areas of extreme temperatures in excess of the allowable range. (14°F~ 122°F / -10°C ~ 50°C)
•
Avoid installing in humid or dusty places. The relative humidity must be below 90%.
•
Avoid installing in places where radiation is present.
•
Avoid installing in places where there are strong magnetic fields and electric signals.
•
Avoid installing in places where the camera would be subject to strong vibrations.
•
Never face the camera toward the sun. Do not aim at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise the camera may be smeared and damaged.
REGULATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance with Directive
2002/96/EC. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By proper waste handling of this product you ensure that it has no negative consequences for the environment and human health, which could otherwise be caused if this product is thrown into the garbage bin. The recycling of materials will help to conserve natural resources.
For more details information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Compliance is evidenced by written declaration from our suppliers, assuring that any potential trace contamination levels of restricted substances are below the maximum level set by EU Directive 2002/95/EC, or are exempted due to their application.
WARNING
DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE
ENCLOSURE.
DO NOT OPEN THE CABINET.
.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
4
.
CAUTION
TABLE OF CONTENTS
32336AC 7
8
INTRODUCTION
OVERVIEW
The HD80 Night Vision HD Indoor/Outdoor IP camera is capable of providing real time streaming video with smooth image quality. The
HD80 offers quad streaming and can be used in a variety of installations including shops, stores, banks, factories and for building surveillance.
With Power over Ethernet (PoE), the need for separate power lines is eliminated and cabling and installation costs can be significantly reduced. The light weight and small size allow for quick and simple installation on either the ceiling or walls of structures or vehicles.
The HD80 is equipped with Digital Wide Dynamic Range, which makes it possible to identify details even in lighting conditions with severe shadows or backlighting, and the IR LEDs make it a perfect camera for dark areas and nighttime surveillance.
Camera Default Settings
IP Address
192.168.0.250
Admin
Username
Password
Management Port
1234
80
Streaming Port (RTSP)
554
Product Features
•
Progressive Scan CMOS Sensor
•
1080p and 3MP Resolution Available
•
H.264 Encoding
•
Dual Streaming
•
Multi-Language Support
•
Tampering Alarm
•
Digital Wide Dynamic Range
•
Motion Detection
•
Privacy Masks
•
Smart Picture Quality / 3D Noise Reduction
•
Network Failure Detection
•
Digital Day/Night (ICR)
•
IR LED Module (working distance up to 25m)
•
MicroSD Support (up to 16GB microSD Card)
•
Weatherproof (IP66 Outdoor Rated)
•
ONVIF Support
ONE: GETTING STARTED
Box Contents
Camera Overview
32335AC 9
BOX CONTENTS
Before proceeding, please check that the box contains the items listed here. If any item is missing or has defects, DO NOT install or operate the product and contact your dealer for assistance.
HD80 Camera Self Tapping Screws Plastic Anchors
Rubber Washers Security Torx Tool CD
Quick Start Guide
CAMERA OVERVIEW
Before installing or connecting the dome camera, please refer to this section and complete preparations for dome setup and all switch settings.
Dome Diagram
3
2
1
1
2
3
Reset button
Lens
Restore camera settings to default settings.
Requires a pin, or paperclip to press button
Turn the lens mount to adjust the pan position.
Tilt Fixed Screw Loosen the screw to adjust the tilt angle
10
Dimensions
Ø4.6” (116.8 mm)
Diameter – 4.6” (116.8 mm)
Height – 3.6” (91.44 mm)
32335AC
Connections
The HD80 cameras use Power over Ethernet (PoE). The only connection on the camera is the RJ45 Ethernet dongle located on the rear of the camera. Connect one end of the Ethernet cable to the dongle, and connect the other end to the recorder, or to a PoE switch.
•
Protect the network cable connection from water damage by running the cord inside a wall or ceiling, or through conduit.
•
If passing the cord through a wall or ceiling, drill a 3/4” hole.
•
For outdoor installations, seal any holes in the wall or ceiling with silicone caulk to protect against water intrusion.
AvertX recommends using Category 5 Ethernet cable to connect the camera to your network. For the best transmission quality, the cable length should not exceed 328 feet (100 meters).
Once you have connected the camera, check the status of the network connection by looking at the link indicator and activity indicator LEDs. If the LEDs are not lit check your network connection. The green link LED indicates a network connection and the orange activity LED flashes to indicate network activity.
11
TWO: CAMERA FINDER
12
AVERTX CAMERA FINDER
Use the included Camera Finder software to easily find your network cameras for initial setup. The AvertX Camera Finder software is included on the software CD with all AvertX IP devices. The Camera
Finder application is also available to download at avertx.com.
Finding IP Cameras
1. Open the Software CD on the recorder.
2. Click Software on the software disc menu.
3. Click Camera Finder.
4. Click Device Search on the Device Search window.
5. If a Windows Security Alert window opens, click Unblock to allow the IP utility to access your network.
6. Click Device Search again to find all connected IP devices.
Tip The default IP address of your IP camera is 192.168.0.250
Note
If you cannot connect to the camera you may need to change the camera’s IP address to match your network settings.
Accessing the Camera
You can view live video and access the camera configuration by accessing the camera in an internet browser.
1. Right-click the desired network device and select Browse.
2. Type the default username and password in the login window to access the video server using your internet browser.
Changing the IP Address
If you are not directly connecting to an AvertX HDIP recorder, you must manually change the IP address. Change the IP address to a number in the same subnet as your existing network or to the recommended network settings for your network.
1. Right-click the desired network device and then click Network
Setup.
2. Select the Static IP option.
3. Enter the new IP Address, Gateway, Netmask, and DNS for camera.
The Might y Squirrel Contr oller
32335AC 13
THREE: SETUP AND CONFIGURATION
Installing the Camera
Connecting to the Camera
Camera Settings
14
INSTALLING THE CAMERA
The camera can be installed directly onto the wall or ceiling. Be sure that the structure is strong enough to support the camera.
Ceiling and Wall Installation
Dome cameras are ideal for installation on a ceiling or soffit location. If you are installing the camera on a wall without a bracket, see
Consideration for Wall Installations.
1. Remove the dome cover following the instructions on the sticker on the base of the camera.
2. Use the included mounting template to pre-drill holes for the mounting screws and, if passing the cable through the ceiling or wall, drill a ¾” hole.
3. Connect an Ethernet cable to the dongle on the camera.
•
Protect the network cable connection from water damage by running the cord inside a wall or ceiling, or through conduit
•
For outdoor installations, seal any holes in the wall or ceiling with silicone caulk to protect against water intrusion.
4. Affix the base of the camera to the wall with the included selftapping screws and wall anchors.
5. Adjust the position of your camera.
6. Replace and secure the dome cover.
Consideration for Wall Installations
When installing a dome camera on a wall without a bracket, you are limited in the direction that you can point the camera lens. Dome cameras should point out perpendicular to the wall surface.
If you choose to turn the camera to point parallel to the wall surface the video image will be sideways.
Note
If the video image is upside down after installation, you can flip
the image 180º. For instructions to rotate the video, see Video
Rotation in this manual or find them at avertx.com/support.
32335AC
Resetting the Camera
If it is necessary to reset the camera to the factory default settings, hold down the Reset button (see Camera Overview) for 30 seconds. This will return all settings, including network setup, to the factory default. The IP address of the camera will return to 192.168.0.250.
MicroSD Card
Your camera includes a microSD card clot (up to 16GB), which can be used for emergency video backup. The microSD card is not included. You must remove the cover of the camera to access the microSD card slot.
Instructions for recording to a microSD card slot can be found at avertx.com/support. microSD slot
Reset Button
Focusing the Camera Lens
The HD80IRM is equipped with an auto-focus lens. You do not need to manually focus the lens. All focus adjustments can be made through the camera software or your HDIP recorder.
For optimal image quality, use the Auto Focus feature on your AvertX camera after the camera is installed.
15
CONNECTING TO THE
CAMERA
Connecting In a Web Browser
1. Type the IP address of the camera in a web browser. or
Use the included Camera Finder software and locate the camera on the IP Finder list, then double-click the camera to open the
Viewer software in your web browser.
2. Log in to the camera with the appropriate User Name and
Password.
Note The default User name is Admin and the default Password is1234. The username and password are case sensitive.
Administrator/User Privileges
The Administrator account has the authority to configure the IP camera and authorize users’ access to the camera. The User accounts have access to the camera with limited authority.
Default Username and Password
The username and password are case sensitive. It is strongly recommended that the password be changed after the initial setup to prevent unauthorized access.
Username – Admin
Password – 1234
Connecting a Stream
AvertX IP cameras are optimized for use with AvertX HDIP recorders, but you can also connect to your AvertX IP cameras using third party software like VLC media player (http://www.videolan.org).
To connect the camera you may need to provide the stream URL. All
AvertX IP cameras are capable of delivering two RTSP streams, as well as streaming MJPEG over HTTP. The stream URLs are listed below. rtsp://<ip address>/mjpeg rtsp://<ipaddress>/h264 http://<ipaddress>:8008
The MJPEG over HTTP stream is identified by a port number. The default port is 8008; this port can be configured in the camera’s System page (click Setup, and then click System).
16
CAMERA SETTINGS
You can access the camera setup menu using an internet browser on your computer. The camera viewer software will install automatically the first time you connect to the camera. If your internet browser doesn’t install the viewer software, check the security settings or ActiveX controls and plug-in settings. If your internet browser asks for permission to install the plugin, you must allow ActiveX or Quicktime to install to continue the installation.
Viewer Tabs
Home – Monitor live video.
Setup – Set the host name , root password, and network related settings, modify the video resolution, adjust the Camera parameters, set
Motion Detection options, and view and update the camera software.
Logout – Change user.
Note For advanced management options, access the camera’s admin panel by adding “/admin” after the camera’s IP address in your browser’s address bar.
32335AC 17
Home
Select the video stream you want to view, H.264-1 (stream 1) or H.264-
2 (stream 2).
Note Advanced users can access additional video stream options, including the MJPEG stream, through the admin panel.
The default when viewing your camera using the web.
Use this to make the image smaller. This can save bandwidth if necessary.
This will show your video at full screen on your monitor.
To exit full screen mode, double-click the video.
Changing the Language
1. Click the Language drop down menu
2. Select a language. The browser will refresh, then display the selected language.
18
Using Digital Zoom Control
In full screen mode, right-click the video image to activate digital zoom and use the scroll wheel to zoom in/out.
Changing the Field of View
The HD80IRM camera has a varifocal optical lens which means it has a variable field of view. You can set the camera to have a wide angle view, or a more zoomed in view to capture exactly what you need to see
– without losing any image quality. Use the Zoom controls to change the field of view of the camera.
•
Tele – zoom in
•
Wide – zoom out
Focusing the Camera
The HD80IRM is equipped with an auto-focus lens. You do not need to manually focus the lens. For optimal image quality, use the Auto Focus feature on your AvertX camera after the camera is installed.
Focus
•
Near – manually adjust the focus near
•
Far – manually adjust the focus far
•
Push AF – completely automatic focus
AF Mode
•
Manual – hold the current focus setting while adjusting the zoom
•
Zm Trig – automatically refocus while adjusting the zoom in and out
Setup
System
Changing the Admin Password
To change the administrator password, type a new password in the
Admin Password box, confirm below, and then click Save.
Note The maximum length of the password is 14 characters. The following characters are valid: A-Z, a-z, 0-9, !#$%&’-.@^_~.
32335AC 19
Network
You can choose to use a fixed IP address or a dynamic IP address
(assigned by a DHCP server or router) for the camera.
Get IP address automatically (DHCP)
The camera comes preconfigured with a fixed IP address, selecting Get
IP address automatically requires a router or DHCP server to assign an IP address to the camera.
Note Every network device has a unique Media Access Control
(MAC) address that can be used for identification. The MAC address is located on the bottom of each camera, and on the box label (AvertX IP Finder also displays the MAC address for identification). Record your camera’s MAC address for identification in the future.
Use fixed IP address
To assign a new static IP address:
1. Select the Use fixed IP address option.
2. Type a new IP address in the IP address box.
3. Type a new address in the Default Gateway box.
4. Click Save to confirm the new setting.
When using static IP address to log in to the IP Camera, you can access it either through the AvertX IP Finder software or type the IP address directly in the Address bar of your internet browser.
General
•
IP address – The IP Address is necessary for network identification.
•
Subnet mask – Used to determine if the destination is in the same subnet. The default value is 255.255.255.0.
•
Default gateway – Used to forward frames to destinations in different subnets or for internet access.
•
Primary DNS – The primary domain name server that translates hostnames into IP addresses. This is usually the gateway or router address.
•
Secondary DNS – A secondary domain name server that backups the primary DNS.
Advanced
•
Web Server port – Defines the port that Internet Explorer uses to connect over the web and view video. If this port is changed then the new port must be defined when attempting to web connect (ex: if your camera’s IP address is 192.168.0.100 and you change the web port to 8001, then you must type http://192.168.0.100:8001 in your browser).
•
RTSP port – The default RTSP port is 554; setting range: 1024
~65535.
•
MJPEG over HTTP port – The default HTTP Port is 8008; setting range: 1024 ~65535.
Note The MJPEG over HTTP port must not be the same as the web server port.
20
Streaming
On the Streaming tab, you can configure specific video resolution, video compression mode, and video protocol and audio transmission mode.
Streaming Settings
Your AvertX IP camera can transmit two streams of video at the same time. One stream can be in high definition for recording, and the other can be a lower resolution used for live display. By using dual streams, you can display more cameras on the monitor of your recorder without taxing the CPU.
Resolution – Set the resolution for each stream.
GOP – Set the Group of Pictures (GOP) size for each stream. This setting can affect image quality and bandwidth. Please consult with technical support before changing this setting.
Bit Rate – Set the data transmission speed for your camera. A lower bit rate will result lower image quality but a smaller file size and more bandwidth availability.
Frame Rate – Set the frame rate of each stream. A lower frame rate will result in more bandwidth availability.
Video Rotation
If your camera is installed on a wall or table top the image may appear to be upside down. Rotate the camera video image using the software to get a right-side-up image.
Note You cannot rotate the video image 90° to get a vertical image.
Rotating the image 90° will stretch and distort the video image.
To rotate the camera video image:
1. Click Setup.
2. Click Streaming.
3. From the Video Rotation list, select the desired rotation.
•
Normal transmits the image as the camera sees it.
•
Flip transmits the image backwards and upside down.
•
Mirror transmits a mirror image.
•
Rotate 90 degree clockwise/counterclockwise
•
180 degree transmits the image upside down.
32335AC 21
Camera
You can adjust your picture quality on both streams using the Camera section of the Setup tab.
Select the video stream you want to adjust (H.264-1 or H.264-2).
There are three options for viewing video:
The default when viewing your camera using the web.
Use this to make the image smaller. This can save bandwidth if necessary.
This will show your video at full screen on your monitor.
To exit full screen mode, double-click the video.
Picture
You can adjust these values as necessary for your installation.
•
Brightness
•
Sharpness
•
Saturation
•
Hue
•
Contrast
Wide Dynamic Range (WDR)
Your camera includes Digital Wide Dynamic Range. If your camera is aimed at an area that includes direct sunlight and dark shade in the same frame, you can lose some of the detail. The WDR function can adjust for these differences to provide detail for both the fully lit area and the shaded area within the frame. Digital WDR uses the Digital Signal
Process (DSP) to brighten darker areas of a scene to provide more detail in dark shade.
Backlight
If your camera is aimed at a doorway or window, and you need to see detailed footage of people in front of that doorway, the difference between light and shadow can make the people difficult to recognize.
Use the Backlight function to adjust for this problem.
22
Motion Detection
Motion Detection allows the camera to detect motion and trigger alarms when the motion level in the detected area exceeds the determined sensitivity threshold value.
When motion detection is activated, the Motion pop-up window will open.
When motion is detected, the signals will be displayed on the Motion window as shown below.
In the Motion Detection page, there is a motion detection window (red box) displayed on the Live View Pane. The Motion Detection window defines the motion detection area. To change the size of the Motion
Detection window, drag the edge of the frame to resize.
You can add up to 10 motion detection windows.
•
Click add under the Live View Pane to add a Motion Detection window.
•
To delete a Motion Detection window, use the mouse to select the frame and click delete.
Motion Detection
Turn motion detection on or off. The default setting is Off.
Motion Detection Setting
•
Sampling pixel interval [1-10] – Default value is 10, which means system will take one sampling pixel for every 10 pixels.
•
Detection level [1-100] – Default detection level is 10. This item sets the detection level for each sampling pixel; the smaller the value, the more sensitive it is.
•
Sensitivity level [1-100] – The default sensitivity level is 80, which means if 20% or more sampling pixels are detected as changing, the system will detect motion. The bigger the value, the more sensitive it is. As the sensitivity value is increased, the red horizontal line in the motion indication window will be lowered accordingly.
•
Time interval (sec) [0-7200] – The default interval is 10. The value is the interval between each detected motion event.
32335AC 23
Software Upgrade
Use the Software Upgrade page to view the current version of camera firmware, and upgrade the firmware if necessary.
Upgrading the Camera Firmware
Note Make sure the new firmware file is available before starting a software upgrade. Do not change the file name, or the system will not be able to update to the new firmware.
1. Download the camera firmware file from avertx.com to a computer and then unzip or extract the file.
2. Access your camera through the web browser.
3. When you have accessed the camera page, click Setup at the top of the page.
4. In the setup menu, click the Software upgrade tab on the left side of the page.
5. Under Upgrade click Browse to locate the firmware file on your computer.
6. Select the file type (uImage_userland) from the list under Step 2.
7. Click Upgrade. The system will check the upgrade file, and then upload the file. The upgrade status bar will display on the page.
Logout
Your AvertX camera will automatically log you out when you close your browser window. If you want to log in as a different user, you will need to use the logout tab.
Logging In as a Different User
To log in to your camera as a different user, follow these instructions.
1. Click the Logout tab.
2. To log in as a different user, type the appropriate user name and password, and then click OK
24
FOUR: SPECIFICATIONS
32335AC 25
CAMERA SPECIFICATIONS
Model
Resolution
Video Format
IP Rating
Wide Dynamic Range
Day / Night
IR LED
IR Range
Focal Length
FOV
Iris Control
Auto White Balance Range
Auto White Balance Range (ATW)
Auto Gain Control
Backlight Compensation
Operating Temperature
Heater
Power Consumption
Input Voltage
Weight
Dimensions
HD80IR Rev B
(3 MP) 2048 x 1536, (2MP / 1080p)1920 x 1080
(1.3 MP) 1280 x 1024, (1MP / 720p) 1280 x 720
(D1) 720 x 480, (CIF) 352 x 240
H.264, MJPEG
IP66
Digital Wide Dynamic Range
True Day/Night, IR Cut Filter
24 LEDs
65 ft (20 m)
3 ~ 9 mm Autofocus
32° ~ 96.1°
Auto Iris
2700 ~ 8000 K
2225 ~ 9300 K
Yes
Yes
18
˚F ~ 118˚F (-8˚C ~ 48˚C)
No
9.3W Max
PoE Only
0.6 lbs (280 kg)
Ø4.6" (116.8 mm) x H: 3.6” (91.44 mm)
26
www.avertx.com
1-8552AVERTX
© 2014 AvertX
All rights reserved. No part of this publication may be reproduced by any means without written permission from AvertX. The information in this publication is believed to be accurate in all respects. However, AvertX cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
IRREL!
32335AC 27
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
