LOCATION OF CONTROL
LOCATION OF CONTROL
1
1) POWER INDICATOR
2
3
2) LCD DISPLAY
3) REMOTE SENSOR
4
4) MINUTE
5
5) HOUR
8
6) TIME SET
9
6
10
7
7) FUNCTION SELECTOR
8) FM STEREO INDICATOR
9) BAND SELECTOR
11
10) TUNING CONTROL
11) CASSETTE DOOR
12) CASSETTE RECORD
13) CASSETTE PLAY
17
12
14) CASSETTE REWIND
13 14 15 16
15) CASSETTE FORWARD
16) CASSETTE STOP / EJECT
17) CASSETTE PAUSE
18) CD DOOR
19) CD DOOR OPEN / CLOSE
20) PROGRAM
21) REPEAT
22) PLAY / PAUSE
18
23) SKIP24) SKIP+
25) STOP
26) VOLUME27) VOLUME+
19
20
27
21
26
22
E-3
23
24
25
LOCATION OF CONTROL
28) BATTERY BACKUP
29) SPEAKER JACK L / R
30) BEAT CUT
31) FM ANTENNA
32) AC CORD
28
30
29
31
32
POWER SOURCE
AC POWER
You can power your appliance by plugging the AC power cord at the back of the appliance into a wall
AC power outlet. Check that the rated voltage of your appliance matches your local voltage.
E-4
REMOTE CONTROL
1.
2.
3.
4.
5.
6.
PLAY / PAUSE
SKIP PROGRAM
STOP
SKIP +
REPEAT
1
2
5
3
6
4
BATTERY INSTALLATION
Insert 2 x “AAA” size batteries into the battery compartment. Be sure that the batteries are inserted
correctly to avoid damage to the remote control. Always remove the batteries when the remote
control will not be used for a long period of time, as this will cause leakage to the batteries and
subsequently damage to your set.
Notes:
- Use batteries of the same type. Never use different types of batteries together.
- If the distance required between the remote control and the appliance decreases, the batteries
are exhausted. In this case replace the batteries with new one.
SENSOR WINDOW OF THE RECEIVER
- Even if the remote control is operated within the effective range, its operation may be impossible if
there are any obstacies between the appliance and the remote control.
- If the remote control is operated near other appliances which generate infrared rays, or if other
remote control devices using infrared rays are used near the appliance, it may operate incorrectly.
E-5
RADIO OPERATION
GENERAL OPERATION
1.
2.
3.
4.
Set the “FUNCTION” selector to “RADIO” mode.
Select desired band by using the “BAND” selector.
Adjust radio frequency to your desired station by using the “TUNING” control.
Adjust the “VOLUME” control to the desired level.
FM / FM-STEREO RECEPTION
- Set the “BAND” selector to FM mode for MONO reception.
- Set the “BAND” selector to FM ST. mode for FM STEREO reception. The Stereo indicator light up
to show FM ST. mode.
FOR BETTER RECEPTION
FM - This appliance has a FM antenna located at the rear cabinet. This wire is completely unraveled
and extended for better reception.
AM - This appliance is equipped with a built - in directional ferrite AM antenna. Rotate the appliance
to get better reception.
E-6
TAPE OPERATION
GENERAL OPERATION
PAUSE
Press to stop playing tape operation temporarily.
Press again to resume tape operation.
STOP / EJECT
Press to stop tape operations.
Press again to open the cassette door after the tape spools stop turning.
FAST FORWARD
REWIND
PLAY
RECORD
&
Press to start rapid tape winding either forward or reverse direction.
Press to start playing tape.
Press it together with “PLAY” button to start recording.
PLAYBACK
1.
2.
3.
4.
5.
6.
7.
Set the “FUNCTION” selector to “TAPE” mode.
Press the “STOP / EJECT” button to open the cassette door and insert your tape.
Close the cassette door.
Press the “PLAY” button to start playing tape.
Adjust the “VOLUME” control to the desired level.
Press the “PAUSE” button when you want to stop playing tape operation temporarily.
Press the “STOP / EJECT” button when finished.
RECORDING
1. Press the “STOP / EJECT” button to open the cassette door and insert a blank tape.
2. Select the source you want to record.
To record from radio - Set the “FUNCTION” selector to “RADIO” mode and adjust the desired station.
To record from CD - Place a disc on the CD compartment. Set the “FUNCTION” selector to “CD”
mode and select the desired track.
3. Press the “RECORD” button together with the “PLAY” button to start recording.
4. Press the “STOP / EJECT” button when finished.
E-7
CD OPERATION
GENERAL OPERATION
PLAY / PAUSE
Press to start playing CD disc.
Press again to stop playing CD operation temporarily.
Press again to resume playback.
SKIP +
SKIP -
Press to go to the next track or back to the previous track.
Press and hold while playing until you find the point of the sound.
&
STOP
Press to stop all CD operation.
PLAYBACK
1.
2.
3.
4.
5.
6.
7.
8.
Set the “FUNCTION” selector to “CD” mode.
Open the CD door and place a CD disc with the label up in the CD compartment.
Close the CD door.
Focus search is performed if disc is inside. Total number of tracks is read and appears on the display.
Press the “PLAY / PAUSE” button to start playing CD disc.
Adjust the “VOLUME” control to the desired level.
Press the “PLAY / PAUSE” button again when you want to stop playback temporarily.
Press the “STOP” button when finished.
E-8
CD OPERATION
PROGRAM
Up to 20 tracks can be programmed for disc play in any order.
Be sure to press the “STOP” button before use.
1. Press the “PROGRAM” button, the display will show “P01” and flash.
2. Select desired track by using the “SKIP +” or “SKIP -” button.
3. Press the “PROGRAM” button again to confirm desired track into the program memory.
4. Repeat step 2 and 3 to enter additional tracks into the program memory.
5. When all the desired tracks have been programmed, press the “PLAY / PAUSE” button to play
the disc in the order you have programmed.
6. Press the “STOP” button twice to terminate programmed playback.
MODE
Press the “REPEAT” button before or during playing CD disc,
each press switches the mode function as follows
:
1 - REPEAT 1
2 - REPEAT ALL
3 - NORMAL PLAYBACK
REP
REP
ALL
REPEAT 1
REPEAT
ALL
NORMAL
PLAYBACK
OTHER FEATURES
CLOCK SETTING
1.
2.
3.
4.
Press the “TIME SET” button. (Do not release “TIME SET” button during time setting)
Press the “HOUR” button to set hour.
Press the “MINUTE” button to set minute.
Release all button to confirm setting. Confirmed setting will on the display.
E-9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement