Cisco | WAP4410N | Datasheet | Cisco Wireless-N Access Point + PoE

Cisco Wireless-N Access Point + PoE
Data Sheet
Cisco WAP4410N Wireless-N Access Point:
PoE/Advanced Security
Cisco Small Business Access Points
Advanced, High-Performance Wireless Access for the Small Business
Supports high-bandwidth applications with the 802.11n standard; backward compatible with
802.11b and g devices
Connects to Power over Ethernet devices, simplifying installation and eliminating the need
for and cost of installing external power supplies
Protects business information with enhanced security, including rogue access point
detection, advanced encryption, and select access filters
Simplifies installation and configuration with easy-to-use web interface
Figure 1.
Cisco WAP4410N Wireless-N Access Point: PoE/Advanced Security
Product Overview
With the growth of high-bandwidth applications, such as storage and video, in the workplace,
network performance is essential. Wireless technology is no longer lagging behind wired
performance. The Cisco WAP4410N Wireless-N Access Point (Figure 1) answers the growing
business need for access, speed, and security.
The Cisco Wireless-N Access Point lets you connect Wireless-N (802.11n), Wireless-G (802.11g),
and Wireless-B (802.11b) devices to your wired network, so you can add PCs to the network with
no cabling hassle. Power over Ethernet (PoE) support makes the access point easy to install - you
can mount it anywhere, even without ready access to a power plug. With appropriate PoE support
at the other end, you need to run only one cable to the access point to deliver both data and
power. Of course, you can also use the included AC adapter if power is available nearby.
© 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 1 of 5
Data Sheet
Moreover, the integrated quality of service (QoS) features provide consistent voice and video
quality on both the wired and wireless networks, enabling the deployment of business-quality voice
over IP (VoIP) and video applications.
To protect your data and privacy, the Cisco Wireless-N Access Point supports the industrialstrength wireless security of Wi-Fi Protected Access (WPA), encoding all your wireless
transmissions with powerful encryption. The MAC address filter lets you decide exactly who has
access to your wireless network, and advanced logging keeps you apprised of access attempts.
The rogue access point detection capability notifies the administrator when an unauthorized
access point is detected in the airspace. The WPS (Wi-Fi Protected Setup) feature facilitates
simple and secure deployment of security in the wireless network. Configuration is a snap with the
web browser-based configuration utility.
The Cisco WAP4410N Wireless-N Access Point is the best way to add wireless access to your
existing business network.
Draft 802.11n wireless networking delivers greater throughput and extended range,
maximizing the number of wireless clients per access point for your small business
Easy installation and configuration via a web interface
Adjustable and removable dipole antennas with multiple-input, multiple-output (MIMO) 3x3
diversity (AP with connector type of RSMA)
Gigabit Ethernet LAN interface
Supports PoE and external DC power
HTTP Redirect facilitates the display of a splash page on initial user access
IPv6 host support for managing the access point over IPv6
Multiple basic service set identifier (BSSID) support allows the creation of multiple secure
wireless workgroups for users and guests
Service set identifier (SSID) to VLAN mapping maintains application security and quality
across wireless and wired
WPS allows for simple and secure deployment of the wireless network
Logging via syslog, email, or local log
Wi-Fi Multimedia (WMM) wireless QoS support
Table 1 lists the specifications, package contents, and minimum requirements for the Cisco
WAP4410N Wireless-N Access Point.
Table 1.
Specifications for the Cisco WAP4410N Wireless-N Access Point: PoE/Advanced Security
Draft IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af
(Power over Ethernet), 802.1x (security authentication), 802.11i security WPA/WPA2,
Ethernet, Power
Cabling type
Unshielded twisted pair (UTP) Category 5e or higher
Power, Ethernet, Wireless, PoE
© 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 2 of 5
Data Sheet
Operating system
Web user interface
Built-in web user interface for easy browser-based configuration (HTTP/HTTPS)
Simple Network Management
Protocol (SNMP) version
Event logging
SNMP version 1, 2c
● Event logging
● Email logging
● Remote syslog
Web firmware upgrade
Firmware upgradeable through web browser
Dynamic Host Configuration
Protocol (DHCP)
DHCP client
HTTP Redirect
Redirects initial user access to an external web server to display company logo or network
usage policy
IPv6 host
● Support for management and control of access point over IPv6
● Supports RFC2460 (IPv6 protocol) and RFC4294 (IPv6 node requirements)
Network Capabilities
Multiple BSSID
Supports up to 4 BSSIDs, allowing the creation of multiple virtual access points
Supports 802.1q - up to 4 VLANs
SSID to VLAN mapping
Supports mapping of SSIDs to VLANs to securely separate workgroups across wireless
and wired domains
Spanning Tree
Supports 802.1d Spanning Tree Protocol to prevent loops when using wireless distribution
system (WDS) links as redundant links in a distribution system
Operating modes
Access point mode, point-to-point bridge mode, point-to-multipoint bridge mode, repeater
mode, wireless client mode
Load balancing
Allows bandwidth control with user-defined CPU usage ratios
Auto-channel selection
On boot-up, the access point selects the least congested channel
802.11d regulatory domain
Enables the access point to provide radio channel settings for client devices, facilitating
easy client access as they move across regulatory domains
Wired Equivalent Privacy (WEP) 64-bit/128-bit, WPA-Pre-Shared Key (WPA-PSK), WPA2PSK, WPA-ENT, WPA2-ENT
Access control
Wireless connection control: MAC-based
SSID broadcast
SSID broadcast enable/disable
Client isolation
Supports wireless client isolation between and within SSIDs
Wireless clients can be authenticated through IEEE 802.1X
802.1X supplicant
Supports 802.1X supplicant on the Ethernet port to allow the access point to authenticate
itself to the network
RADIUS server
Up to 2 RADIUS servers can be configured for redundancy purposes
Supports WPS, a WI-FI Alliance specification for simple and secure setup of a wireless
Rogue access point detection
New access points detected that have not been categorized as known are logged as rogue
access points, allowing the administrator to clamp down on unapproved devices in the
Quality of Service
● 4 queues
● 802.1p VLAN priority
● WMM wireless priority
● Mapping of 802.1p VLAN priority to WMM wireless priority to maintain end-to-end QoS
Radio and modulation type: 802.11b/DSSS, 802.11g/OFDM, 802.11n/OFDM
Operating channels: 11 North America, 13 most of Europe (ETSI and Japan)
© 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 3 of 5
Data Sheet
Internal antennas
External antennas
3 (omnidirectional)
Transmit power
Transmit power @ normal temp range for FCC:
802.11b: 16 dBm @ 1TX, 19 dBm @ 2TX, 20.5 dBm @ 3TX
802.11g: 13 dBm @ 1TX, 16 dBm @ 2TX, 17.5 dBm @ 3TX
802.11n: 17 dBm @ 1TX @ MCS0~5/8~13, 13 dBm @ 1TX @ MCS6/14,
11 dBm @ 1TX @ MCS7/15, 20 dBm @ 2TX@MCS0~5/8~13,
16 dBm @ 2TX @ MCS6/14, 14 dBm @ 2TX @ MCS7/15,
21.5 dBm @ 3TX@MCS0~5/8~13, 17.5 dBm @ 3TX @ MCS6/14,
15.5 dBm @ 3TX @ MCS7/15
Transmit power @ normal temp range for ETSI:
11b/g/n: 13 dBm @ 1TX, 16 dBm @ 2TX, 17.5 dBm @ 3TX
Antenna gain in dBi
Receiver sensitivity
802.11.n: 300 Mbps at -69dBm
802.11.g: 54 Mbps at -73dBm
802.11.b: 11 Mbps at -88dBm
6.69 x 6.69 x 1.60 in.
(170 x 170 x 40.7 mm)
0.86 lb (39 kg)
● 12V 1A DC input, and IEEE 802.3af compliant PoE
● Max power draw: 10.1W
Operating temperature
32° to 104°F (0° to 40°C)
Storage temperature
-4° to 158°F (-20° to 70°C)
Operating humidity
10% to 85%, noncondensing
Storage humidity
5% to 90%, noncondensing
Package Contents
● Cisco WAP4410N Wireless-N Access Point with PoE
● User guide on CD-ROM
● Ethernet network cable
● Power adapter
● Product stands
● Registration card
Minimum Requirements
● 802.11b, 802.11g, 802.11n wireless adapter with TCP/IP protocol installed per PC
● Switch/router with PoE support or PoE injector when used with PoE
● Web-based configuration: Java-enabled web browser
Product Warranty
3-year limited hardware warranty with return to factory replacement and 90-day limited software warranty.
Cisco Limited Warranty for Cisco Small Business Series Products
This Cisco Small Business product comes with 3-year limited hardware warranty with return to
factory replacement and a 90-day limited software warranty. In addition, Cisco offers software
application updates for bug fixes and telephone technical support at no charge for the first 12
months following the date of purchase. To download software updates, go to:
Product warranty terms and other information applicable to Cisco products are available at
© 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 4 of 5
Data Sheet
For More Information
For more information on Cisco Small Business products and solutions, visit:
Printed in USA
© 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
C78-501860-00 11/08
Page 5 of 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF