tecno rs seating system
TECNO RS SEATING SYSTEM
SURFACE MOUNT WITH BASE PLATE INSTALLATION INSTRUCTIONS
MATERIALS INCLUDED
a
b
f
c
d
g
e
h
STEP BY STEP
i
k
TOOLS NEEDED
1/4" punch
l
steel wire brush
pencil
M8 hex key
(perch only)
3/16", 3/8" & 5/8" drill
bits for concrete
j
M6 hex key
(perch only)
hammer drill
hammer
Loctite
M12 hex key
FOR SURFACE MOUNT CYLINDRICAL MOUNTING POST OR PERCH LEG WITH BASE PLATE.
Surface mount plate top view
Mark hole locations
Drill holes
Insert & set anchors
• Place surface mount plate in desired
location. Mark center of each hole
location with a pencil.
• Use hammer drill to drill 2-1/4" deep x
5/8" diameter anchor hole at each
marked location using a 5/8" drill bit
suitable for concrete drilling.
• Use compressed air and steel wire brush
to clean each anchor hole.
NOTE: To ensure proper placement dry
fit surface mount plate, mounting tie rod
and seat rail in desired location. Once
secure, ensure that connection holes in
the seat rail and mounting post brackets
align before marking surface mount
plate location.
NOTE: Forms+Surfaces recommends
starting holes with 3/16" diameter drill
bit followed by 3/8" and finally 5/8" for
maximum accuracy.
• Insert 1/2"-13 x 2" anchor (a) into each
anchor hole and use hammer to tap
anchor tops flush with ground level.
• Use 1/4" punch and hammer to set
anchors by driving down the center of
each anchor until it stops.
T 800.451.0410 | www.forms-surfaces.com
© 2016 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 1 of 4 | Rev. 05-06-16
TECNO RS SEATING SYSTEM
SURFACE MOUNT WITH BASE PLATE INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR SURFACE MOUNT CYLINDRICAL MOUNTING POST OR PERCH LEG WITH BASE PLATE.
f
g
Birds-eye view
b
c
d
e
b
c
d
e
Position surface mount plate
Attach surface mount plate cover
Attach mounting tie rod
• Position surface mount plate so that
mounting holes line up with anchors.
• Slide surface mount plate cover, then
centering disc onto the threaded rod in
surface mount plate.
• Screw mounting tie rod onto threaded rod
on surface mount base plate.
• Slide 1/2” stainless steel lock washer (c),
then 1/2” stainless steel flat washer (d)
and 1/2” nylon flat washer (e) onto each
1/2”-13 x 1-1/2” tamper-resistant button
head cap screw (b).
• Insert button head cap screw into
surface mount plate.
• Secure surface mount plate cover and
centering disc to the surface mount plate
using the M16 flat washer (g) and M16
hex nut (f).
• Tighten tie rod until snug.
• Tighten nut until snug.
• Tighten screw until snug.
T 800.451.0410 | www.forms-surfaces.com
© 2016 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 2 of 4 | Rev. 05-06-16
TECNO RS SEATING SYSTEM
SURFACE MOUNT WITH BASE PLATE INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR SURFACE MOUNT CYLINDRICAL MOUNTING POST OR PERCH LEG WITH BASE PLATE.
7
9
8
h
i
j
Position mounting post
Attach seat rail to mounting post
Secure seat rail
• Slide cylindrical or perch mounting post
over tie rod and centering disc.
• Once all mounting posts are in position,
place seat rail onto rail mounting
brackets. Ensure that connection holes in
the seat rail and mounting brackets align.
• Seat rail should now be secured to the
mounting posts.
NOTE: For Perch configurations you
will need to attach the rail mounting
bracket before moving on to step 8.
Rail mounting bracket slides onto perch
mounting post.
• Insert M12 lock washer (j), then M12
x 120 socket head cap screw (i) into
seat rail to secure seat rail to the rail
mounting bracket.
• Tighten screw until snug.
• Fit nylon cap (h) onto the top of socket
head cap screw.
T 800.451.0410 | www.forms-surfaces.com
© 2016 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 3 of 4 | Rev. 05-06-16
TECNO RS SEATING SYSTEM
SURFACE MOUNT WITH BASE PLATE INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR SURFACE MOUNT CYLINDRICAL MOUNTING POST OR PERCH LEG WITH BASE PLATE.
10
10
10
k
l
k
k
k
k
For configurations with backed seats
For configurations with backless seats
For configurations with perch seats
• Position backed seat on seat bracket
ensuring that mounting holes line up.
• Position backless seat on seat bracket
ensuring that mounting holes line up.
• Position perch seat on seat bracket
ensuring that mounting holes line up.
• Insert M8 x 35 socket head cap screws
(k) using an M8 hex key to secure
backed seat to seat bracket.
• Insert M8 x 35 socket head cap screws
(k) using an M8 hex key to secure
backed seat to seat bracket.
• Tighten screws until snug.
• Tighten screws until snug.
• Insert M6 set screw (l) as shown above
using an M6 hex key to secure the front
of the perch seat. Insert M8 x 35 socket
head cap screw (k) using an M8 hex key
to secure perch seat to seat bracket.
NOTE: Forms+Surfaces recommends
applying Loctite® or similar threadlocking adhesive.
NOTE: Forms+Surfaces recommends
applying Loctite® or similar threadlocking adhesive.
• Tighten screws until snug.
NOTE: Forms+Surfaces recommends
applying Loctite® or similar threadlocking adhesive.
T 800.451.0410 | www.forms-surfaces.com
© 2016 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 4 of 4 | Rev. 05-06-16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement