Cisco Rack Mount Kit 1RU
Data Sheet
Cisco Catalyst 3560-E Series Switches
®
®
Cisco Catalyst 3560-E Series is (Figure 1) an enterprise-class line of standalone
access and aggregation switches that facilitate the deployment of secure converged
applications while maximizing investment protection for evolving network and application
requirements. Combining 10/100/1000 and Power over Ethernet (PoE) configurations with
10 Gigabit Ethernet uplinks, the Cisco Catalyst 3560-E Series access switches enhance
worker productivity by enabling applications such as IP telephony, wireless, and video.
Cisco Catalyst 3560-E Series aggregation switches deliver secure nonstop unified
network services and versatile connectivity in a one rack-unit (1-RU) form factor for space
and power constrained environments, enabling businesses to reduce total cost of
ownership while maximizing investment protection.
Cisco Catalyst 3560-E Series Primary Features
●
Cisco TwinGig converter module for migrating uplinks from Gigabit Ethernet to 10 Gigabit
Ethernet
●
Cisco EnergyWise for greenhouse gas emissions and operational cost optimization by
measuring, reporting, and reducing energy consumption across the entire corporate
infrastructure, well beyond the scope of IT.
●
PoE configurations with 15.4W of PoE on all 48 ports
●
Enhanced PoE supporting up to 20W of PoE per port
●
Industry first portfolio to scale beyond 15.4W per port delivering maximum solution
simplicity for 802.11n access point deployments
●
Access switch models have modular fan and power supply with externally available backup
●
Dual redundant modular power supplies and fans for Cisco Catalyst 3560E-12D and
Catalyst 3560E-12SD aggregation switches for nonstop operation
●
Multicast routing, IPv6 routing, and access control list (ACL) in hardware
●
Out-of-band Ethernet management port along with RS-232 console port
Figure 1.
Cisco Catalyst 3560-E Series Access and Aggregation Switches
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 1 of 23
Data Sheet
Switch Configurations
Table 1 shows the Cisco Catalyst 3560-E Series configurations:
Table 1.
Switch Configurations.
Feature
Description
Cisco Catalyst 3560E-24TD
24 Ethernet 10/100/1000 ports and 2 X2 10 Gigabit Ethernet uplinks
Cisco Catalyst 3560E-24PD
24 Ethernet 10/100/1000 ports with PoE and 2 X2 10 Gigabit Ethernet uplinks
Cisco Catalyst 3560E-48TD
48 Ethernet 10/100/1000 ports and 2 X2 10 Gigabit Ethernet uplinks
Cisco Catalyst 3560E-48PD
48 Ethernet 10/100/1000 ports with PoE and 2 X2 10 Gigabit Ethernet uplinks
Cisco Catalyst 3560E-48PD-F
48 Ethernet 10/100/1000 ports with 15.4W PoE on all 48 ports and 2 X2 10 Gigabit Ethernet
uplinks
Cisco Catalyst 3560E-12D
12 X2 10 Gigabit Ethernet ports
Cisco Catalyst 3560E-12SD
12 SFP Gigabit Ethernet ports and 2 X2 10 Gigabit Ethernet ports
Cisco Catalyst 3560-E Series Fixed Configuration Aggregation Switches
The Cisco Catalyst 3560E-12D, a 12-port 10 Gigabit Ethernet switch, and the Cisco Catalyst
3560E-12SD, a 12-port SFP Gigabit Ethernet switch with 2 10 Gigabit Ethernet uplink ports offer
flexible and highly available aggregation solutions for nonstop unified network services. Dynamic
routing, dual hot-swappable power supplies, and redundant field-replaceable fans enhance switch
availability. Compatibility with the Cisco TwinGig module makes the Cisco Catalyst 3560-E Series
aggregation switches ideal solutions for networks undergoing a gradual upgrade from Gigabit
Ethernet to 10 Gigabit Ethernet. This future-proofs the network for forthcoming business growth
while reducing the total cost of ownership.
The Cisco Catalyst 3560E-12D and Catalyst 3560E-12D are well suited for space- and powerconstrained deployments because of the compact 1RU form factor, economical power needs and
efficient cooling. Ideally suited to support secure converged applications such as Cisco
TelePresence and unified communications, the Cisco Catalyst 3560E-12D and Catalyst 3560E12SD deliver high-performance intelligent switching with the robust feature set.
Figure 2.
Cisco Catalyst 3560E-12D and Cisco Catalyst 3560E-12SD Switch (Back)
Cisco Catalyst 3560-E Software
The Cisco Catalyst 3560-E Series is available with either the IP Base or the IP Services feature
set. The IP Base feature set includes advanced quality of service (QoS), rate-limiting, ACLs, and
basic static and Routing Information Protocol (RIP) routing capability. The IP Services feature set
provides a richer set of enterprise-class features, including advanced hardware-based IP unicast
and multicast routing -- Enhanced Interior Gateway Routing Protocol [EIGRP], Open Shortest Path
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 2 of 23
Data Sheet
First [OSPF], Border Gateway Protocol [BGP], Protocol Independent Multicast [PIM] and IPv6
routing such as OSPFv3 and EIGRPv6
Customers can transparently upgrade the software feature set in the Cisco Catalyst 3560-E Series
®
Switches through Cisco IOS Software Activation. Software activation authorizes and enables the
Cisco IOS Software feature sets. A special file contained in the switch, called a license file, is
examined by Cisco IOS Software when the switch is powered on. Based on the license’s type,
Cisco IOS Software activates the appropriate feature set. License types can be changed or
upgraded to activate a different feature set. For detailed information about Software Activation,
visit http://www.cisco.com/go/sa.
Cisco EnergyWise Technology
Cisco EnergyWise is an innovative architecture, added to the Cisco Catalyst 3560-E switches,
promoting companywide sustainability by reducing energy consumption across an entire corporate
infrastructure and affecting more than 50 percent of global GhG emissions created by worldwide
building infrastructure, a much greater effect than the 2 percent generated by the IT industry. Cisco
EnergyWise enables companies to measure the power consumption of network infrastructure and
network-attached devices and manage power consumption with specific policies, reducing power
consumption to realize increased cost savings, potentially affecting any powered device.
EnergyWise encompasses a highly intelligent network-based approach to communicate messages
that measure and control energy between network devices and endpoints. The network discovers
Cisco EnergyWise manageable devices, monitors their power consumption, and takes action
based on business rules to reduce power consumption. EnergyWise uses a unique domainnaming system to query and summarize information from large sets of devices, making it simpler
than traditional network management capabilities. Cisco EnergyWise’s management interfaces
allow facilities and network management applications to communicate with endpoints and each
other using the network as a unifying fabric. The management interface uses standard SNMP or
SSL to integrate Cisco and third-party management systems.
Cisco EnergyWise extends the network as a platform for power control plane for gathering,
managing, and reducing power consumption of all devices, resulting in companywide optimized
power delivery and reduced energy costs.
10 Gigabit Ethernet Uplinks and the Cisco TwinGig Small Form-Factor Pluggable
Converter
The Cisco Catalyst 3560-E features wire-speed 10 Gigabit Ethernet uplink ports for high-bandwidth
applications relieving congestion and helping ensure smooth delivery of data. The TwinGig
converter (see Figure 3) converts a 10 Gigabit Ethernet X2 interface into two Gigabit Ethernet
Small Form-Factor Pluggable (SFP) ports. This way, customers can initially use the switch with
Gigabit Ethernet uplinks and later implement 10 Gigabit Ethernet uplinks as business demands
change, without having to upgrade the access layer.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 3 of 23
Data Sheet
Figure 3.
Cisco TwinGig Adapter Converting 10 Gigabit Ethernet X2 Interface into Two Gigabit Ethernet
SFP Interfaces
Modular Power Supplies
The Cisco Catalyst 3560-E Series access switches have one power supply slot and support the
following power supplies. PoE switches require a PoE power supply. Data-only switches can
operate with any of the power supplies:
●
C3K-PWR-1150WAC: 1150WAC power supply with 800W PoE
●
C3K-PWR-750WAC: 750WAC power supply for 24-port switch with 420W PoE
●
C3K-PWR-265WAC: 265WAC power supply for 48- or 24-port switch without PoE
●
C3K-PWR-265WDC: 265WDC power supply for 48- or 24-port switch without PoE
Maximum power availability for converged voice and data networks is attainable when a Cisco
Catalyst 3560-E Series Switch is combined with the Cisco Redundant Power System 2300 (Cisco
RPS 2300) for transparent protection against internal power supply failures and an uninterruptible
power supply (UPS) system to safeguard against power outages. Using the Cisco RPS 2300 to
provide backup power, the Cisco Catalyst 3560-E Series Switch power supplies become hot
swappable. Table 4 shows the power supply compatibility matrix.
The Cisco Catalyst 3560E-12D and the Cisco Catalyst 3560E-12SD aggregation switches have
dual redundant power supplies that can be replaced, one at a time, without service interruption.
Customers can choose from AC, DC, and mixed power supply options:
●
C3K-PWR-300WAC: Cisco Catalyst 3560E-12D and 3560E-12SD 300WAC power supply
●
C3K-PWR-300WDC: Cisco Catalyst 3560E-12D and 3560E-12SD 300WDC power supply
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 4 of 23
Data Sheet
Power over Ethernet
The Cisco Catalyst 3560-E Series can provide a lower total cost of ownership for deployments that
®
incorporate Cisco IP phones, Cisco Aironet wireless LAN (WLAN) access points, or any IEEE
802.3af-compliant end device. PoE removes the need for wall power to each PoE-enabled device
and eliminates the cost for additional electrical cabling and circuits that would otherwise be
necessary in IP phone and WLAN deployments. The Cisco Catalyst 3560-E 24-port PoE
configurations can support 24 simultaneous full-powered PoE ports at 15.4W for full powereddevice support. The Cisco Catalyst 3560-E 48-port PoE configurations can support 48
simultaneous full-powered PoE ports at 15.4W when using the optional 1150W power supply.
Alternatively, for deployments that do not need full PoE on all ports, a smaller power supply can be
used in conjunction with Cisco Catalyst Intelligent Power Management to support 24-port and 48port PoE configurations.
The Cisco Catalyst 3560-E Series also features Enhanced Power over Ethernet support, the
capability to power a growing number of devices from a single switch port, enabling greater
operational simplicity and flexibility for secure converged networks. Industry first portfolio to scale
beyond 15.4W per port delivering maximum solution simplicity for 802.11n access point
deployments, as well as other PoE-powered devices such as phones, monitors, digital signs,
medical devices, card readers and more.
Redundant Power System
The Cisco Catalyst 3560-E Series access switches support the new generation of Cisco RPS
2300, which increases availability in a converged data, voice, and video network by providing
transparent power backup to two of six attached Cisco Catalyst 3560-E Series Switches at the
same time. The failed power supply can be swapped out while the switch is being powered up by
the Cisco RPS 2300. The Cisco Catalyst 3560E-12D and 3560E-12SD aggregation switches don’t
support the RPS, they provide redundancy and switch uptime with dual redundant modular power
supplies.
Primary Features and Benefits
Ease of Use: Deployment
The Cisco Catalyst 3560-E offers ease of use features such as Cisco Smartports, which enable
fast and easy configuration of advanced Cisco Catalyst intelligent capabilities, encapsulating years
of Cisco networking expertise. Cisco Smartports macros offer a set of verified feature templates
per connection type that are easy to apply, enabling users to consistently and reliably configure
essential security, IP telephony, availability, QoS, and manageability features with minimal effort
and expertise.
Other ease of use features include:
●
Dynamic Host Configuration Protocol (DHCP) autoconfiguration of multiple switches
through a boot server eases switch deployment.
●
Automatic QoS (AutoQoS) simplifies QoS configuration in voice-over-IP (VoIP) networks by
issuing interface and global switch commands to detect Cisco IP phones, classify traffic,
and help enable egress queue configuration.
●
Autonegotiation on all ports automatically selects half- or full-duplex transmission mode to
optimize bandwidth.
●
Dynamic Trunking Protocol (DTP) facilitates dynamic trunk configuration across all
switch ports.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 5 of 23
Data Sheet
●
Port Aggregation Protocol (PAgP) automates the creation of Cisco Fast EtherChannel
®
groups or Gigabit EtherChannel groups to link to another switch, router, or server.
●
Link Aggregation Control Protocol (LACP) allows the creation of Ethernet channeling with
devices that conform to IEEE 802.3ad. This feature is similar to Cisco EtherChannel
technology and PAgP.
●
Automatic media-dependent interface crossover (MDIX) automatically adjusts transmit and
receive pairs if an incorrect cable type (crossover or straight-through) is installed.
●
Unidirectional Link Detection Protocol (UDLD) and Aggressive UDLD allow unidirectional
links caused by incorrect fiber-optic wiring or port faults to be detected and disabled on
fiber-optic interfaces.
Availability and Scalability
The Cisco Catalyst 3560-E Series is equipped with a robust set of features that allow for network
scalability and higher availability. This is achieved through IP routing as well as a complete suite of
Spanning Tree Protocol enhancements aimed to maximize availability in a Layer 2 network.
Enhancements to the standard Spanning Tree Protocol, such as Per-VLAN Spanning Tree Plus
(PVST+), Uplink Fast, and Port Fast, as well as innovations such as Flexlink, maximize network
uptime.
●
Flexlink provides link redundancy with convergence time less than 100ms without Spanning
Tree Protocol. A pair of interfaces configured as primary and backup links can load balance
traffic based on VLAN. IEEE 802.1s/w Rapid Spanning Tree Protocol (RSTP) and Multiple
Spanning Tree Protocol (MSTP) provide rapid spanning-tree convergence independent of
spanning-tree timers and also offer the benefit of Layer 2 load balancing and distributed
processing.
●
Per-VLAN Rapid Spanning Tree (PVRST+) allows rapid spanning-tree reconvergence on a
per-VLAN spanning-tree basis, without requiring the implementation of spanning-tree
instances.
●
Cisco Hot Standby Router Protocol (HSRP) is supported to create redundant, failsafe
routing topologies.
●
Switch-port Autorecovery (Errdisable) automatically attempts to reactivate a link that is
disabled because of a network error.
High-Performance IP Routing
Cisco Express Forwarding hardware routing architecture delivers extremely high-performance IP
routing in the Cisco Catalyst 3560-E Series Switches.
●
Basic IP unicast routing protocols (Static, Routing Information Protocol Version 1 [RIPv1],
and RIPv2, RIPng, EIGRP stub) are supported for small-network routing applications.
●
Advanced IP unicast routing protocols (OSPF, EIGRP, and BGPv4) are supported for load
balancing and constructing scalable LANs. IPv6 routing (OSPFv3 and EIGRPv6) is
supported in hardware for maximum performance. The IP Services feature set is required.
●
Equal-cost routing facilitates Layer 3 load balancing and redundancy.
●
Policy-based routing (PBR) allows superior control by facilitating flow redirection regardless
of the routing protocol configured. The IP Services feature set is required.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 6 of 23
Data Sheet
●
HSRP provides dynamic load balancing and failover for routed links, up to 32 unique HSRP
links supported per unit. The group number can be reused for each VLAN configured in the
switch.
●
Protocol Independent Multicast (PIM) for IP multicast routing is supported, including PIM
sparse mode (PIM-SM), Source Specific Multicast (SSM), PIM dense mode (PIM-DM), PIM
sparse-dense mode and Source Specific Multicast (SSM). The IP Services feature set is
required.
●
Web Control Caching Protocol (WCCPv2) enables Wide Area Acceleration Services
(WAAS), resulting in improved application response time and conservation of WAN
bandwidth.
●
Fallback bridging forwards non-IP traffic between two or more VLANs. The IP Services
feature set is required.
Superior Quality of Service
The Cisco Catalyst 3560-E Series offers Gigabit Ethernet speed with intelligent services that keep
everything flowing smoothly, even at 10 times the normal network speed. Industry-leading
mechanisms for marking, classification, and scheduling deliver superior performance for data,
voice, and video traffic, all at wire speed.
Following are some of the QoS features supported in the Cisco Catalyst 3560-E Series Switches:
●
802.1p class of service (CoS) and differentiated services code point (DSCP) field
classification is provided, using marking and reclassification on a per-packet basis by
source and destination IP address, MAC address, or Layer 4 TCP/UDP port number.
●
Cisco control-plane and data-plane QoS ACLs on all ports help ensure proper marking on a
per-packet basis.
●
Four egress queues per port help enable differentiated management of up to four traffic
types across the switch.
●
Shaped Round Robin (SRR) scheduling helps ensure differential prioritization of packet
flows by intelligently servicing the ingress queues and egress queues.
●
Weighted Tail Drop (WTD) provides congestion avoidance at the ingress and egress
queues before a disruption occurs.
●
Strict priority queuing helps ensure that the highest-priority packets are serviced ahead of
all other traffic.
●
The Cisco committed information rate (CIR) function provides bandwidth in increments as
low as 8 Kbps.
●
Rate limiting is provided based on source and destination IP address, source and
destination MAC address, Layer 4 TCP/UDP information, or any combination of these
fields, using QoS ACLs (IP ACLs or MAC ACLs), class maps, and policy maps.
●
Up to 64 aggregate or individual policers are available per Fast Ethernet or Gigabit Ethernet
port.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 7 of 23
Data Sheet
Advanced Security
The Cisco Catalyst 3560-E Series supports a comprehensive set of security features for
connectivity and access control, including ACLs, authentication, port-level security, and identitybased network services with 802.1x and extensions. This set of comprehensive features not only
helps prevent external attacks, but defends the network against “man-in-the-middle” attacks, a
primary concern in today’s business environment. The switch also supports the Network
Admission Control (NAC) security framework.
●
DHCP Snooping prevents malicious users from spoofing a DHCP server and sending out
invalid addresses. This feature is used by other primary security features to prevent a
number of other attacks such as ARP poisoning.
●
Dynamic ARP Inspection (DAI) helps ensure user integrity by preventing malicious users
from exploiting the insecure nature of the ARP protocol.
●
IP source guard prevents a malicious user from spoofing or taking over another user’s IP
address by creating a binding table between the client’s IP and MAC address, port, and
VLAN.
●
Private VLANs restrict traffic between hosts in a common segment by segregating traffic at
Layer 2, turning a broadcast segment into a nonbroadcast multi-access-like segment.
●
Private VLAN Edge provides security and isolation between switch ports, which helps
ensure that users cannot snoop on other users’ traffic.
●
Unicast RPF feature helps mitigate problems caused by the introduction of malformed or
forged (spoofed) IP source addresses into a network by discarding IP packets that lack a
verifiable IP source address.
●
IEEE 802.1x allows dynamic, port-based security, providing user authentication.
●
IEEE 802.1x with VLAN assignment allows a dynamic VLAN assignment for a specific user
regardless of where the user is connected.
●
IEEE 802.1x with voice VLAN permits an IP phone to access the voice VLAN irrespective of
the authorized or unauthorized state of the port.
●
IEEE 802.1x and port security are provided to authenticate the port and manage network
access for all MAC addresses, including that of the client.
●
IEEE 802.1x with an ACL assignment allows for specific identity-based security policies
regardless of where the user is connected.
●
IEEE 802.1x with guest VLAN allows guests without 802.1x clients to have limited network
access on the guest VLAN.
●
Web authentication for non-802.1x clients allows non-802.1x clients to use an SSL-based
browser for authentication.
●
Multi-Domain Authentication allows an IP phone and a PC to authenticate on the same
switch port while placing them on appropriate voice and data VLANs.
●
MAC Auth Bypass (MAB) for voice allows third-party IP phones without an 802.1x
supplicant to get authenticated using their MAC address.
●
Cisco security VLAN ACLs on all VLANs prevent unauthorized data flows from being
bridged within VLANs.
●
Cisco standard and extended IP security router ACLs define security policies on routed
interfaces for control-plane and data-plane traffic. IPv6 ACLs can be applied to filter IPv6
traffic.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 8 of 23
Data Sheet
●
Port-based ACLs for Layer 2 interfaces allow security policies to be applied on individual
switch ports.
●
Secure Shell (SSH) Protocol, Kerberos, and Simple Network Management Protocol Version
3 (SNMPv3) provide network security by encrypting administrator traffic during Telnet and
SNMP sessions. SSH Protocol, Kerberos, and the cryptographic version of SNMPv3 require
a special cryptographic software image because of U.S. export restrictions.
●
Bidirectional data support on the Switched Port Analyzer (SPAN) port allows the Cisco
intrusion detection system (IDS) to take action when an intruder is detected.
●
TACACS+ and RADIUS authentication facilitates centralized control of the switch and
restricts unauthorized users from altering the configuration.
●
MAC Address Notification allows administrators to be notified of users added to or removed
from the network.
●
Port Security secures the access to an access or trunk port based on MAC address.
●
Multilevel security on console access prevents unauthorized users from altering the switch
configuration.
●
Bridge protocol data unit (BPDU) guard shuts down Spanning Tree PortFast-enabled
interfaces when BPDUs are received to avoid accidental topology loops.
●
Spanning Tree Root Guard (STRG) prevents edge devices not in the network
administrator’s control from becoming Spanning Tree Protocol root nodes.
●
IGMP filtering provides multicast authentication by filtering out nonsubscribers and limits
the number of concurrent multicast streams available per port.
●
Dynamic VLAN assignment is supported through implementation of VLAN Membership
Policy Server client capability to provide flexibility in assigning ports to VLANs. Dynamic
VLAN facilitates the fast assignment of IP addresses.
Intelligent Power over Ethernet (PoE) Management
The Cisco Catalyst 3560-E PoE models support Cisco IP phones and Cisco Aironet wireless LAN
(WLAN) access points, as well as any IEEE 802.3af-compliant end device. The Cisco Catalyst
3560-E-48PD can support 48 simultaneous full-powered PoE ports at 15.4W with the 1150W
power supply.
●
Cisco Discovery Protocol version 2 allows the Cisco Catalyst 3560-E Series Switch to
negotiate a more granular power setting when connecting to a Cisco powered device, such
as IP phones or access points, than what is provided by IEEE classification.
●
Per Port power consumption command allows customer to specify maximum power setting
on an individual port.
●
Per Port PoE Power Sensing measures actual power being drawn, enabling more intelligent
control of powered devices.
●
The PoE MIB provides proactive visibility into power usage and allows customers to set
different power level thresholds
●
Link Layer Discovery Protocol (LLDP and LLDP-MED) adds support for IEEE 802.1AB link
layer discovery protocol for interoperability in multivendor networks. Switches exchange
speed, duplex, and power settings with end devices such as IP phones.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 9 of 23
Data Sheet
Management and Control Features
The Cisco Catalyst 3560-E Series Switches come with a rich set of management and control
features that include:
●
Cisco IOS Software CLI support provides common user interface and command set with all
Cisco routers and Cisco Catalyst desktop switches.
●
Generic On-Line Diagnostics (GOLD) checks the health of hardware components and
verifies proper operation of the system data and control plane at run time and boot time.
●
Virtual Route Forwarding (VRF)-Lite enables a service provider to support two or more
VPNs with overlapping IP addresses.
●
Switching Database Manager Templates for access, routing, and VLAN deployment allow
the administrator to easily maximize memory allocation to the desired features based on
deployment-specific requirements.
●
With Cisco IOS Software IP SLAs, users can verify service guarantees, increase network
reliability by validating network performance, proactively identify network issues, and
increase return on investment (ROI) by easing the deployment of new IP services.
●
Local Proxy Address Resolution Protocol (ARP) works in conjunction with Private VLAN
Edge to minimize broadcasts and maximize available bandwidth.
●
VLAN1 minimization allows VLAN1 to be disabled on any individual VLAN trunk.
●
Internet Group Management Protocol (IGMP) Snooping for IPv4 and IPv6 MLD v1 and v2
Snooping provide fast client joins and leaves of multicast streams and limit bandwidthintensive video traffic to only the requestors.
●
Multicast VLAN Registration (MVR) continuously sends multicast streams in a multicast
VLAN while isolating the streams from subscriber VLANs for bandwidth and security
reasons.
●
Per-port broadcast, multicast, and unicast storm control prevents faulty end stations from
degrading overall systems performance.
●
Voice VLAN simplifies telephony installations by keeping voice traffic on a separate VLAN
for easier administration and troubleshooting.
●
Cisco VLAN Trunking Protocol (VTP) supports dynamic VLANs and dynamic trunk
configuration across all switches.
●
Remote Switch Port Analyzer (RSPAN) allows administrators to remotely monitor ports in a
Layer 2 switch network from any other switch in the same network.
●
For enhanced traffic management, monitoring, and analysis, the Embedded Remote
Monitoring (RMON) software agent supports four RMON groups (history, statistics, alarms,
and events).
●
Layer 2 traceroute eases troubleshooting by identifying the physical path that a packet
takes from source to destination.
●
Trivial File Transfer Protocol (TFTP) reduces the cost of administering software upgrades
by downloading from a centralized location.
●
Network Timing Protocol (NTP) provides an accurate and consistent timestamp to all
intranet switches.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 10 of 23
Data Sheet
●
Multifunction LEDs per port for port status; half-duplex and full-duplex mode; and 10BASET, 100BASE-TX, and 1000BASE-T indication as well as switch-level status LEDs for
system, redundant-power supply, and bandwidth utilization provide a comprehensive and
convenient visual management system.
●
Jumbo frames (9216 bytes) are available on the 10/100/1000 configurations for advanced
data and video applications requiring very large frames.
Network Management Tools
The Cisco Catalyst 3560-E Series offers both a superior command-line interface (CLI) for detailed
configuration and Cisco Network Assistant software, a PC-based tool for quick configuration based
on preset templates. In addition, CiscoWorks LAN Management Solution (LMS) supports the Cisco
Catalyst 3560-E Series for networkwide management.
Cisco Network Assistant
A PC-based network management application designed for small and medium-sized business
(SMB) networks with up to 250 users, Cisco Network Assistant offers centralized network
management and configuration capabilities. Cisco Network Assistant uses Cisco Smartports
technology to simplify both initial deployment and ongoing maintenance. This application also
features an intuitive GUI where users can easily apply common services across Cisco switches,
routers, and access points, such as:
●
Configuration management
●
Troubleshooting advice
●
Inventory reports
●
Event notification
●
Network security settings
●
Password synchronization
●
Drag-and-drop Cisco IOS Software upgrades
●
Secure wireless
For detailed information about Cisco Network Assistant, go to: http://www.cisco.com/go/cna.
CiscoWorks LAN Management Solution (LMS)
CiscoWorks LMS is a suite of powerful management tools that simplify the configuration,
administration, monitoring, and troubleshooting of Cisco networks. It integrates these capabilities
into a world-class solution for improving the accuracy and efficiency of your operations staff, while
increasing the overall availability of your network. LMS supports over 400 different device types,
including the Cisco Catalyst 3560-E Series Switches, and it provides:
●
Network discovery, topology views, end-station tracking, and VLAN management
●
Real-time network fault analysis with easy-to-deploy device-specific best-practice templates
●
Hardware and software inventory management, centralized configuration tools, and Syslog
monitoring
●
Network response time and availability monitoring and tracking
●
Real-time device, link, and port traffic management, analysis, and reporting
For detailed information about CiscoWorks LMS, go to:
http://www.cisco.com/en/US/products/sw/cscowork/ps2425/index.html.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 11 of 23
Data Sheet
Cisco Catalyst 3560 SFP Interconnect Cable
The Cisco Catalyst 3560 SFP Interconnect Cable (see Figure 4) provides for a low-cost point-topoint Gigabit Ethernet connection between Cisco Catalyst 3560 switches. The 50cm cable is an
alternative to using SFP transceivers when interconnecting Cisco Catalyst 3560 switches through
their SFP ports over a short distance.
Figure 4.
Cisco Catalyst 3560 SFP Interconnect Cable
Product Specifications
Table 2 lists product specifications for the Cisco Catalyst 3560-E Series.
Table 2.
Descriptions and Specifications
Description
Specification
Performance
Switching Fabric
128 Gbps
DRAM
128 MB / 256 MB *
FLASH
64 MB
VLANs
1K
VLAN IDs
4K
Switched Virtual Interfaces (SVIs)
1K
Jumbo Frames
9216 Byte
Forwarding rate:
3560E-24TD
65.5 Mpps
3560E-24PD
65.5 Mpps
3560E-48TD
101.2 Mpps
3560E-48PD
101.2 Mpps
3560E-48PD-F
101.2 Mpps
3560E-12D
90 Mpps
3560E-12SD
47.6 Mpps
MAC, routing, security, and QoS scalability numbers depend on the type of template
used in the switch:
Default
Template
Default
Template
Access
Template
VLAN Template Routing
Template
MAC address
6K
4K
12K
3K
IGMP groups
and multicast
routes
1K
1K
1K
1K
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 12 of 23
Data Sheet
Connectors and Cabling
Total unicast
routes
8K
6K
0
11K
Directly
connected
hosts
6K
4K
0
3K
Indirect routes
2K
2K
0
8K
Security ACEs
1K
2K
1K
1K
QoS ACEs
0.5K
0.5K
0.5K
0.5K
PBR ACEs
0
0.5K
0
0.5K
● 1000BASE-T ports: RJ-45 connectors, 2-pair Cat-5 UTP cabling
● 1000BASE-T SFP-based ports: RJ-45 connectors, 2-pair Cat-5 UTP cabling
● 100BASE-FX, 1000BASE-SX, -LX/LH, -ZX, -BX10 and CWDM SFP-based ports: LC
fiber connectors (single-mode, or multimode fiber)
● 10GBASE-SR, LR, ER, CX4, LX4, LRM X2-based ports: SC fiber connectors (singlemode, or multimode fiber)
● Ethernet management port: RJ-45 connectors, 2-pair Cat-5 UTP cabling
● Management console port: RJ-45-to-DB9 cable for PC connections
Power Connectors
● Customers can provide power to an access switch by using either the internal power
supply or the Cisco RPS 2300. The connectors are located at the back of the switch.
● The Cisco Catalyst 3560E-12D and Catalyst 3560E-12SD have dual power supplies and
do not support the RPS.
● Internal power supply connector: The internal power supply is an autoranging unit. The
internal power supply supports input voltages between 100 and 240VAC. Use the
supplied AC power cord to connect the AC power connector to an AC power outlet.
● Cisco RPS connector: The connector offers connection for an optional Cisco RPS 2300
that uses AC input and supplies DC output to the switch.
● Only the Cisco RPS 2300 (model PWR-RPS2300) should be attached to the redundantpower-supply receptacle.
Indicators
● Per-port status LEDs: link integrity, disabled, activity, speed, and full-duplex indications
● System-status LEDs: system, RPS, and bandwidth-utilization indications (on the Cisco
Catalyst 3560E-12D and 3560E-12SD only: system, power supplies, fans)
Dimensions (H x W x D)
3560E-24TD
Centimeters
1.75 x 17.5 x 18.1
4.45 x 44.5 x 46.0
3560E-24PD
1.75 x 17.5 x 18.1
4.45 x 44.5 x 46.0
3560E-48TD
1.75 x 17.5 x 18.1
4.45 x 44.5 x 46.0
3560E-48PD
1.75 x 17.5 x 18.1
4.45 x 44.5 x 46.0
3560E-48PD-F
1.75 x 17.5 x 21.7
4.45 x 44.5 x 55.2
3560E-12D
1.75 x 17.5 x 19.5
4.45 x 44.5 x 49.5
3560E-12SD
1.75 x 17.5 x 15
4.45 x 44.5 x 38.1
Pounds
Kilograms
17.9
8.1
Weight
3560E-24TD
Environmental Ranges
Inches
3560E-24PD
18.3
8.3
3560E-48TD
18.8
8.6
3560E-48PD
19.2
8.75
3560E-48PD-F
20.9
9.5
3560E-12D
23.5
10.7
3560E-12SD
16
7.27
● Operating temperature: 32 to 113ºF (0 to 45ºC)
● Storage temperature: –13 to 158ºF (–25 to 70ºC)
● Relative humidity operating: 0 to 95% (noncondensing)
● Relative humidity nonoperating: 10 to 85% (noncondensing)
● Operating altitude: up to 10,000 ft (3049 m)
● Storage altitude: up to 15,000 ft (4573 m)
● Cisco Catalyst 3560E-12D and Catalyst 3560E-12SD: up to 50,000 feet over allowable
temperature range; NEBS - up to 13,000 feet [4000 m]
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 13 of 23
Data Sheet
Acoustic Noise
Mean Time Between Failure
(MTBF)
International Organization for Standardization (ISO) 7779: bystander position operating to
an ambient temperature of 30ºC
3560E-24TD
45 dB
3560E-48TD
45 dB
3560E-24PD
45 dB
3560E-48PD
45 dB
3560E-48PD-F
48 dB
3560E-12D
44 dB
3560E-12SD
44 dB
3560E-24TD
181,086 hours
3560E-24PD
168,753 hours
3560E-48TD
166,907 hours
3560E-48PD
151,196 hours
3560E-48PD-F
151,196 hours
3560E-12D
147,001 hours
3560E-12SD
206,950 hours
Table 3 lists the management and standards support for the Cisco Catalyst 3560-E Series.
Table 3.
Description
Management
Management and Standards Support for Cisco Catalyst 3560-E Series Switches
Specification
● BRIDGE-MIB
● CISCO-CDP-MIB
● CISCO-VTP-MIB
● ENTITY-MIB
● CISCO-CLUSTER-MIB
● CISCO-CONFIG-MAN-MIB
● ETHERLIKE-MIB
● IF-MIB
● CISCO-ENTITY-FRU-CONTROL-MIB
● CISCO-ENVMON-MIB
● IGMP-MIB
● IPMROUTE-MIB
● CISCO-FLASH-MIB
● CISCO-FTP-CLIENT-MIB
● OLD-CISCO-CHASSIS-MIB
● OLD-CISCO-FLASH-MIB
● CISCO-HSRP-MIB
● CISCO-HSRP-EXT-MIB
● OLD-CISCO-INTERFACES-MIB
● OLD-CISCO-IP-MIB
● CISCO-IGMP-FILTER-MIB
● CISCO-IMAGE-MIB
● OLD-CISCO-SYS-MIB
● OLD-CISCO-TCP-MIB
● CISCO-IP-STAT-MIB
● CISCO-L2L3-INTERFACE-CONFIG-MIB
● OLD-CISCO-TS-MIB
● OSPF-MIB (RFC 1253)
● CISCO-POE-EXTENSIONS-MIB
● CISCO-MAC-NOTIFICATION-MIB
● PIM-MIB
● RFC1213-MIB
● CISCO-MEMORY-POOL-MIB
● CISCO-PAGP-MIB
● RFC1253-MIB
● RMON-MIB
● CISCO-PING-MIB
● CISCO-PROCESS-MIB
● RMON2-MIB
● SNMP-FRAMEWORK-MIB
● CISCO-RTTMON-MIB
● CISCO-STP-EXTENSIONS-MIB
● SNMP-MPD-MIB
● SNMP-NOTIFICATION-MIB
● CISCO-SYSLOG-MIB
● CISCO-TCP-MIB
● SNMP-TARGET-MIB
● SNMPv2-MIB
● CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB
● CISCO-VLAN-MEMBERSHIP-MIB
● TCP-MIB
● UDP-MIB
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 14 of 23
Data Sheet
Standards
● IEEE 802.1s
● IEEE 802.1w
● 1000BASE-LX/LH
● 1000BASE-BX10-U
● IEEE 802.1x
● IEEE 802.3ad
● 1000BASE-BX10-D
● 1000BASE-ZX
● IEEE 802.3af
● IEEE 802.3x full duplex on 10BASE-T,
100BASE-TX, and 1000BASE-T ports
● IEEE 802.1D Spanning Tree Protocol
● 1000BASE-CWDM SFP 1470 nm
● 1000BASE-CWDM SFP 1490 nm
● IEEE 802.1p CoS Prioritization
● IEEE 802.1Q VLAN
● 1000BASE-CWDM SFP 1550 nm
● 1000BASE-CWDM SFP 1570 nm
● IEEE 802.3 10BASE-T specification
● IEEE 802.3u 100BASE-TX specification
● 1000BASE-CWDM SFP 1590 nm
● 1000BASE-CWDM SFP 1610 nm
● IEEE 802.3ab 1000BASE-T specification
● IEEE 802.3z 1000BASE-X specification
● 10GBASE-SR
● 10GBASE-LR
● 100BASE-FX
● 1000BASE-T
● 10GBASE-ER
● RMON I and II standards
● 1000BASE-SX
● SNMPv1, SNMPv2c, and SNMPv3
● 1000BASE-CWDM SFP 1510 nm
● 1000BASE-CWDM SFP 1530 nm
Table 4 lists the power supply compatibility matrix for all different models of Cisco Catalyst 3560-E
Series Switches.
Table 4.
Power Supply Compatibility Matrix
Cisco Catalyst 3560-E
Series Switch Type
Power Supply
C3K-PWR1150WAC
C3K-PWR750WAC
C3K-PWR265WAC
C3K-PWR265WDC
C3K-PWR300WAC
C3K-PWR300WDC
48-Port PoE Switch
X
X
–
–
–
–
24-Port PoE Switch
X
X
–
–
–
–
48-Port Switch
X
X
X
X
–
–
24-Port Switch
X
X
X
X
–
–
Cisco RPS 2300
X
X
–
–
–
–
Cisco Catalyst
3560E-12D
–
–
–
–
X
X
Cisco Catalyst
3560E-12SD
–
–
–
–
X
X
Table 5 lists the power specifications for the Cisco Catalyst 3560-E Series based on the kind of
power supply used.
Table 5.
Power Specifications
Description
Specifications
C3K-PWR1150WAC
C3K-PWR750WAC
C3K-PWR265WAC
Max Output Power
1150W
750W
Total Output BTU (Note:
1000 BTU/hr = 290W)
3939 BTU/hr,
1150W
2568 BTU/hr,
765W
Input-Voltage Range and
Frequency
115–240VAC,
50–60 Hz
Input Current
Output Ratings
Output Holdup Time
C3K-PWR265WDC
C3K-PWR300WAC
C3K-PWR300WDC
265W
265W
300W
300W
907 BTU/hr,
265W
907 BTU/hr,
265W
1034 BTU/hr, 300W
100–240VAC,
50–60 Hz
100–240VAC,
50–60 Hz
-36VDC to 72VDC
85–265VAC,
47–63 Hz
12-6A
10-5A
5-2.5A
<5A@-72VDC 4-2A
<10A@36VDC
8A
12V@25A
12V@25A
12V@22A
12V@22A
12V@25A
12V@25A
-52V@16.4A
-52V@8.75A
20 ms
minimum
20 ms
minimum
20 ms
minimum
> 2ms@48VDC
20 ms
minimum
8ms
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
-40.5VDC to 72VDC
Page 15 of 23
Data Sheet
Power-Supply Input
Receptacles
IEC 320-C14
IEC 320-C14
IEC 320-C14
(IEC60320C14)
(IEC60320C14)
(IEC60320C14)
Power Cord Rating
15A
15A
15A
Description
–
IEC 320-C14
–
(IEC60320C14)
12A@100VDC
10A
12AWG
Specifications
WS-C3560E48PD-SF
WS-C3560E24PD-S
WS-C3560E48PD-S
WS-C3560E24TD-S
WS-C3560E48TD-S
C3K-PWR1150WAC
C3K-PWR750WAC
C3K-PWR265WAC
C3K-PWR265WDC
C3K-PWR300WAC
Measured Power
Consumption
146W
89W
133W
89W
151W
Measured Output
BTU/hr
498
303
451
303
514
Measured Power
Consumption
137W
94W
124W
96W
141W
Measured Output
BTU/hr
466
320
420
292
481
Switch Power:
558W
Switch Power:
297W
Switch Power:
332W
N/A
N/A
PoE Power: 385W
PoE Power: 193W
PoE Power: 196W
At the Switch: 590
At the Switch: 355
At the Switch: 464
N/A
N/A
N/A
N/A
N/A
N/A
100% Throughput
5% Throughput
5% Throughput (with 50% PoE loads)
Measured Power
Consumption
Measured Output
BTU/hr
100% Throughput (with maximum possible PoE loads)
Measured Power
Consumption
Measured Output
BTU/hr
Switch Power:
972W
Switch Power:
502W
Switch Power:
540W
PoE Power: 744W
PoE Power: 372W
PoE Power: 375W
At the Switch: 778
At the Switch: 443
At the Switch: 561
Note:
Disclaimer: All power consumption numbers were measured under controlled laboratory conditions
and are provided as an estimate.
The wattage rating on the power supply does not represent actual power draw. It indicates the
maximum power draw possible by the power supply. This rating can be used for facility capacity
planning. For PoE switches, cooling requirements are smaller than the actual power consumption
as a significant portion of PoE loads are dissipated in the end points
Non-PoE Power Consumption
100 Percent Throughput Switch Power Consumption
The numbers indicate the power consumed by a typical switch under normal conditions. Normal
conditions signify a temperature of 25 degrees Celsius, atmospheric pressure in the range of 860
to 1060 mbar and relative humidity from 30 to 75 percent. Typically such power draws are only
seen when encountering a 100 percent traffic load made up entirely of 64 byte packets on the
switch and the uplinks.
5 Percent Throughput Switch Power Consumption
The numbers indicate the power consumed by a typical switch under normal conditions. Normal
conditions signify a temperature of 25 degrees Celsius, atmospheric pressure in the range of 860
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 16 of 23
Data Sheet
to 1060 mbar and relative humidity from 30 to 75 percent. The numbers below indicate a 5 percent
traffic load on the switch and its uplinks.
PoE Power Consumption
100 Percent Throughput Switch Power Consumption (no PoE loads)
The numbers indicate the power consumed by a typical switch under normal conditions. Normal
conditions signify a temperature of 25 degrees Celsius, atmospheric pressure in the range of 860
to 1060 mbar and relative humidity from 30 to 75 percent. Typically such power draws are only
seen when encountering a 100 percent traffic load made up entirely of 64 byte packets with no
PoE loads on the switch and uplinks.
Measured 5 Percent Throughput Switch Power Consumption (no PoE loads)
The numbers indicate the power consumed by a typical switch under normal conditions. Normal
conditions signify a temperature of 25 degrees Celsius, atmospheric pressure in the range of 860
to 1060 mbar and relative humidity from 30 to 75 percent. The numbers below indicate a 5 percent
traffic load on the switch and its uplinks
100 Percent Throughput Switch Power Consumption (with maximum PoE loads)
The numbers indicate the power consumed by a typical system (the switch and the corresponding
PoE loads) under normal conditions. Normal conditions signify a temperature of 25 degrees
Celsius, atmospheric pressure in the range of 860 to 1060 mbar and relative humidity from 30 to
75 percent. Typically this power draw is realized when a switch is running 100 percent traffic load
of 64 byte sized packets on all its ports and uplinks and also drawing 100 percent PoE load .
5 Percent Throughput Switch Power Consumption (with 50 percent PoE loads).
The numbers indicate the power consumed by a typical system (the switch and the corresponding
PoE loads) under normal conditions. Normal conditions signify a temperature of 25 degrees
Celsius, atmospheric pressure in the range of 860 to 1060 mbar and relative humidity from 30 to
75 percent. The numbers below indicate a 5 percent traffic load and 50 percent PoE load on the
switch and its uplinks.
Table 6 lists the specifications of all the power supplies supported in Cisco Catalyst 3560-E Series
Switches.
Table 6.
Power Supply Specifications
Product Specifications
Physical Specifications
Power Supply
C3K-PWR1150WAC
C3K-PWR750WAC
C3K-PWR265WAC
C3K-PWR265WDC
C3K-PWR300WAC
(H x W x D):
1.65 X 6.0 X
14.90 in
(H x W x D):
1.65 X 6.0 X
11.4 in
(H x W x D):
1.65 X 6.0 X
11.4 in
(H x W x D):
1.65 X 6.0 X
11.4 in
(H x W x D):
Weight: 5.6 lb
(2.6 kg)
Weight: 3.9 lb
(1.8 kg)
Weight: 3.3 lb
(1.5 kg)
Weight: 3.5 lb
(1.6 kg)
C3K-PWR300WDC
1.58 X 4.0 x 9.0 in
Weight: (2 Kg)
Operating Temperature
23 to 113°F (-5 to 45°C)
23 to 131°F (-5 to 55°C)
Storage Temperature
-40 to 158°F (-40 to 70°C)
-40 to 185°F (-40 to 85°C)
Relative Humidity
Operating
10 to 85% noncondensing
10 to 90% noncondensing
Relative Humidity
Nonoperating
0 to 95% noncondensing
5 to 95% noncondensing
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 17 of 23
Data Sheet
Altitude
10,000 ft. (3000 meters), up to 45°C
Operating: -500 to 10,000 ft.
(-152 to 3048 m) over allowable
temperature range
Nonoperating: -1,000 to 50,000
ft. (-304 to 15,240 m) over
allowable temperature range
MTBF
Calculated MTBF must be greater than 300,000 hrs using
Telcordia SR-332, Method 1, Case 3. Demonstrated MTBF is
500,000 hrs (with 90% confidence level).
EMI and EMC
Compliance
Calculated
MTBF 220,000
hrs with fan
(MIL HDBK
217F formula).
Demonstrated
MTBF 150,000
hrs with 90%
confidence.
Calculated
MTBF 662,000
hrs with fan
(Bellcore
formula).
Demonstrated
MTBF 150,000
hrs with 90%
confidence.
● FCC Part 15 (CFR 47) Class A
● ICES-003 Class A
● EN 55022 Class A
● CISPR 22 Class A
● AS/NZS 3548 Class A
● VCCI Class A
● EN 55024
● EN300 386
● EN 50082-1
● EN 61000-3-2
● EN 61000-3-3
● EN 61000-6-1
● NEBS Compliant (Except C3K-PWR-1150WAC and C3K-PWR-750WAC)
Safety Compliance
● UL 60950-1 1st Edition
● CAN/CSA-C22.2 No. 60950-1 1st Edition
● EN 60950-1 1st Edition
● IEC 60950-1 1st Edition
LED Indicators
● “AC OK” or “DC IN”: Input power to the power supply is
OK.
● “PS OK”: Output power from the power supply is OK.
● “AC OK”: Input power to the
power supply is OK.
● “PS OK”: Output power from
the power supply is OK.
Table 7 lists the safety and compliance information for the Cisco Catalyst 3560-E Series.
Table 7.
Safety and Compliance
Description
Safety Certifications
Specification
● UL60950-1
● C-UL to CAN/CSA 22.2 No.60950-1
● TUV/GS to EN 60950-1
● CB to IEC 60950-1 with all country deviations
● CE Marking
● CCC for PS FRU
Electromagnetic Emissions
Certifications
● FCC Part 15 Class A
● EN 55022 Class A (CISPR22 Class A)
● CNS13438 Class A (applicable only to FRU power supplies)
● AS/NZS CISPR22 Class A
● EN55024
● GR-1089 CORE Class A
● EN 300 368
● MIC
● CE Marking
● China (applicable only to FRU power supplies)
NEBS
● GR-63-CORE, GR-1089-CORE
● Level 3 Type 2, 4 and Wall Mount
● AT&T TP76200 Checklist
● TCG NEBS Checklist
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 18 of 23
Data Sheet
ETSI
EN 300 019 - Storage: Class 1.2, Transportation: Class 2.3, In-Use: Class 3.2
Environmental
Reduction of Hazardous Substances (ROHS) 5
Noise Specifications
Office Product Spec: 48dBA at 30°C (refer to ISO 7779)
Telco
CLEI code
Warranty
Limited lifetime warranty
Hardware Warranty
Cisco Catalyst 3560-E Series Switches come with the standard Cisco limited lifetime warranty for
hardware, as described at:
http://www.cisco.com/en/US/docs/general/warranty/English/LH2DEN__.html.
Cisco Services for Access Switching
Cisco and our partners can help you create a robust, dependable Cisco Access Switching solution.
The Cisco lifecycle approach to services defines the requisite activities at each phase of the
solution lifecycle. Assessments help align your solution to business goals and gauge readiness to
support new technology. Effective planning and design expedite solution adoption. Award-winning
technical support increases operational efficiency, and optimization improves performance,
resiliency, stability, and predictability and prepares your network and teams for change. For more
information, visit http://www.cisco.com/go/services.
Ordering Information
Table 8 lists ordering information for the Cisco Catalyst 3560-E Series. To place an order, visit the
Cisco ordering homepage at
http://www.cisco.com/en/US/ordering/or13/or8/order_customer_help_how_to_order_listing.html.
Table 8.
Cisco Catalyst 3560-E Series Ordering Info
Product Number
Product Description
Cisco Catalyst 3560-E Series
WS-C3560E-24TD-S
● 24 10/100/1000 ports + 2 X2-based 10 Gigabit Ethernet ports
● 128-Gbps wire rate, nonblocking switching fabric capacity
● Field-replaceable 265WAC power supply and fan tray
● 1 rack unit (RU) fixed configuration multilayer switch
● IPv6
● IP Base software feature set (IPB)
WS-C3560E-24TD-E
● 24 10/100/1000 ports + 2 X2-based 10 Gigabit Ethernet ports
● 128-Gbps wire rate, nonblocking switching fabric capacity
● Field-replaceable 265WAC power supply and fan tray
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Services software feature set (IPS)
● Provides full IPv6 dynamic routing
WS-C3560E-48TD-S
● 48 10/100/1000 ports + 2 X2-based 10 Gigabit Ethernet ports
● 128-Gbps wire rate, nonblocking switching fabric capacity
● Field-replaceable 265WAC power supply and fan tray
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Base software feature set (IPB)
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 19 of 23
Data Sheet
WS-C3560E-48TD-E
● 48 10/100/1000 ports + 2 X2-based 10 Gigabit Ethernet ports
● 128-Gbps wire rate, nonblocking switching fabric capacity
● Field-replaceable 265WAC power supply and fan tray
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Services software feature set (IPS)
● Provides full IPv6 dynamic routing
WS-C3560E-24PD-S
● 24 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports
● 128-Gbps wire rate, nonblocking switching fabric capacity
● Field-replaceable 750WAC power supply and fan tray
● 420W available for Enhanced PoE, allowing > 15.4W to all 24 ports
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Base software feature set (IPB)
WS-C3560E-24PD-E
● 24 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports
● 128-Gbps wire rate, nonblocking switching fabric capacity
● Field-replaceable 750WAC power supply and fan tray
● 420W available for Enhanced PoE, allowing > 15.4W to all 24 ports
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Services software feature set (IPS)
● Provides full IPv6 dynamic routing
WS-C3560E-48PD-S
● 48 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports
● 128-Gbps wire rate, nonblocking switching fabric capacity
● Field-replaceable 750WAC power supply and fan tray
● 420W available for Enhanced PoE allowing > 15.4W for up to 24 ports
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Base software feature set (IPB)
WS-C3560E-48PD-E
● 48 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports
● 128-Gbps wire rate, nonblocking switching fabric capacity
● Field-replaceable 750WAC power supply and fan tray
● 420W available for Enhanced PoE allowing > 15.4W for up to 24 ports
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Services software feature set (IPS)
● Provides full IPv6 dynamic routing
WS-C3560E-48PD-SF
● 48 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports
● 128-Gbps wire rate, nonblocking switching fabric capacity
● Field-replaceable 1150WAC power supply and fan tray
● 800W available for Enhanced PoE, allowing > 15.4W to all 48 ports
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Base software feature set (IPB)
WS-C3560E-48PD-EF
● 48 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports
● 128-Gbps wire rate, nonblocking switching fabric capacity
● Field-replaceable 1150WAC power supply and fan tray
● 800W available for Enhanced PoE, allowing > 15.4W to all 48 ports
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Services software feature set (IPS)
● Provides full IPv6 dynamic routing
WS-C3560E-12D-S
● 12 X2-based 10 Gigabit Ethernet ports
● 60 Gbps, backplane utilization 2:1 oversubscribed
● Dual hot-swappable 300WAC or DC power supplies and redundant fans
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Base software feature set (IPB)
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 20 of 23
Data Sheet
WS-C3560E-12D-E
● 12 X2-based 10 Gigabit Ethernet ports
● 60 Gbps, backplane utilization 2:1 oversubscribed
● Dual hot-swappable 300WAC or DC power supplies and redundant fans
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Services software feature set (IPS)
● Provides full IPv6 dynamic routing
WS-C3560E-12SD-S
● 12 SFP based Gigabit Ethernet ports + 2 X2-based 10 Gigabit Ethernet ports
● 68 Gbps, wire rate backplane
● Dual hot-swappable 300WAC or DC power supplies and redundant field-replaceable
fans
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Base software feature set (IPB)
WS-C3560E-12SD-E
● 12 SFP based Gigabit Ethernet ports + 2 X2-based 10 Gigabit Ethernet ports
● 68 Gbps, wire rate backplane
● Dual hot-swappable 300WAC or DC power supplies and redundant field-replaceable
fans
● 1-RU fixed configuration multilayer switch
● IPv6
● IP Services software feature set (IPS)
● Provides full IPv6 dynamic routing
Cisco Catalyst 3560-E Series Product Activation Keys
3560E-LIC=
Cisco Catalyst 3560-E Series Product Activation Keys Configurations
3560E-IPSLCB-QTY
IP Services for 3560-E, upgrade from the IP Base Feature Set
3560E12D-SLB-QTY
IP Services for 3560E-12D, upgrade from IP Base
3560E12SD-SLB-QTY
IP Services for 3560E-12SD, upgrade from IP Base
Power Supplies and Fan Module for the Cisco Catalyst 3560-E Series
C3K-PWR-265WAC=
Catalyst 3750-E/3560-E 265WAC power supply
C3K-PWR-265WDC=
Catalyst 3750-E/3560-E 265WDC power supply
C3K-PWR-750WAC=
Catalyst 3750-E/3560-E/RPS 2300 750WAC power supply
C3K-PWR-1150WAC=
Catalyst 3750-E/3560-E/RPS 2300 1150WAC power supply
C3K-BLWR-60CFM=
Fan Module for the Catalyst 3750-E/3560-E
Power Supplies and Fan Module for the Cisco Catalyst 3560E-12D and Catalyst 3560E-12SD Aggregation Switches
C3K-PWR-300WAC=
Catalyst 3560E-12D and Catalyst 3560E-12SD 300WAC power supply spare
C3K-PWR-300WDC=
Catalyst 3560E-12D and Catalyst 3560E-12SD 300WDC power supply spare
C3K-FAN-16CFM=
Fan Module for the Catalyst 3560E-12D and Catalyst 3560E-12SD
Redundant Power System for the Cisco Catalyst 3560-E Series
PWR-RPS2300
Cisco Redundant Power System 2300 and Blower,No Power Supply
ACC-RPS2300=
Spare Accessory Kit for Cisco Redundant Power System 2300
BLNK-RPS2300=
Spare Bay Insert for Cisco Redundant Power System 2300
CAB-RPS2300=
Spare RPS2300 Cable for Devices other than E-Series Switches
CAB-RPS2300-E=
Spare RPS2300 Cable for Catalyst 3750E/3560E Switches
PWR-RPS2300=
Spare RPS 2300 Chassis w/ Blower, PS blank, No Power Supply
BLWR-RPS2300=
Spare 45CFM Blower for Cisco Redundant Power System 2300
C3K-PWR-750WAC=
Catalyst 3750-E/3560-E/RPS 2300 750WAC power supply spare
C3K-PWR-1150WAC=
Catalyst 3750-E/3560-E/RPS 2300 1150WAC power supply spare
TwinGig Converter Module for the Cisco Catalyst 3560-E Series
CVR-X2-SFP
TwinGig Converter Module
CVR-X2-SFP=
TwinGig Converter Module
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 21 of 23
Data Sheet
SFPs for the Cisco Catalyst 3560-E Series
GLC-GE-100FX=
100BASE-FX SFP for GE SFP port on 3750,3560.2970,2960
GLC-LH-SM=
GE SFP,LC connector LX/LH transceiver
GLC-SX-MM=
GE SFP, LC connector SX transceiver
GLC-T=
1000BASE-T SFP
GLC-ZX-SM=
1000BASE-ZX SFP
GLC-BX-D=
1000BASE-BX SFP, 1490NM
GLC-BX-U=
1000BASE-BX SFP, 1310NM
CWDM-SFP-1470=
CWDM 1470 NM SFP Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1490=
CWDM 1490 NM SFP Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1510=
CWDM 1510 NM SFP Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1530=
CWDM 1530 NM SFP Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1550=
CWDM 1550 NM SFP Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1570=
CWDM 1570 NM SFP Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1590=
CWDM 1590 NM SFP Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1610=
CWDM 1610 NM SFP Gigabit Ethernet and 1G/2G FC
DWDM SFPs for Cisco Catalyst 3560-E Series (not currently supported with the Cisco Catalyst 3560E-12D & Catalyst
3560E-12SD)
DWDM-SFP-3033=
DWDM SFP 1530.33 nm SFP (100 GHz ITU grid)
DWDM-SFP-3112=
1000BASE-DWDM 1531.12 nm SFP (100 GHz ITU grid)
DWDM-SFP-3190=
1000BASE-DWDM 1531.90 nm SFP (100 GHz ITU grid)
DWDM-SFP-3268=
DWDM SFP 1532.68 nm SFP (100 GHz ITU grid)
DWDM-SFP-3425=
DWDM SFP 1534.25 nm SFP (100 GHz ITU grid)
DWDM-SFP-3504=
DWDM SFP 1535.04 nm SFP (100 GHz ITU grid)
DWDM-SFP-3582=
DWDM SFP 1535.82 nm SFP (100 GHz ITU grid)
DWDM-SFP-3661=
DWDM SFP 1536.61 nm SFP (100 GHz ITU grid)
DWDM-SFP-3819=
DWDM SFP 1538.19 nm SFP (100 GHz ITU grid)
DWDM-SFP-3898=
DWDM SFP 1538.98 nm SFP (100 GHz ITU grid)
DWDM-SFP-3977=
DWDM SFP 1539.77 nm SFP (100 GHz ITU grid)
DWDM-SFP-4056=
DWDM SFP 1540.56 nm SFP (100 GHz ITU grid)
DWDM-SFP-4214=
DWDM SFP 1542.14 nm SFP (100 GHz ITU grid)
DWDM-SFP-4294=
DWDM SFP 1542.94 nm SFP (100 GHz ITU grid)
DWDM-SFP-4373=
DWDM SFP 1543.73 nm SFP (100 GHz ITU grid)
DWDM-SFP-4453=
DWDM SFP 1544.53 nm SFP (100 GHz ITU grid)
10GB X2 Module for Cisco Catalyst 3560-E Series
X2-10GB-ER=
10GBASE-ER X2 Module
X2-10GB-LR=
10GBASE-LR X2 Module
X2-10GB-SR=
10GBASE-SR X2 Module
X2-10GB-LRM=
10GBASE-LRM X2 Module
X2-10GB-LX4=
10GBASE-LX4 X2 Module
X2-10GB-CX4=
10GBASE-CX4 X2 Module
LC to SC Cables for the Cisco Catalyst 3560-E Series
CSS5-CABLX-LCSC=
CSS11500 10-Meter Fiber Single Mode LX LC-to-SC Connectors
CSS5-CABSX-LC=
CSS11500 10-Meter Fiber Multimode SX LC Connectors
CSS5-CABSX-LCSC=
CSS11500 10-Meter Fiber Multimode SX LC-to-SC Connectors
Spare Power Cords for the Cisco Catalyst 3560-E Series
CAB-AC=
Power Cord, 110V
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 22 of 23
Data Sheet
CAB-16AWG-AC=
AC Power cord, 16AWG
CAB-ACA=
Plug, Power Cord, Australian, 10A
CAB-ACE=
Power Cord Europe
CAB-ACI=
Power Cord-Italian
CAB-ACR=
Power Cord Argentina
CAB-ACS=
Power Cord for Switzerland
CAB-ACU=
Power Cord UK
CAB-JPN=
Power Cord-Japan
CAB-L620P-C13-US=
Power Cord, 250VAC, 15A, NEMA L6-20 to C13, US
CAB-L620P-C13-JPN=
Power Cord, 250VAC, 15A, NEMA L6-20 to C13, JAPAN
CAB-IND=
Power Cord India
CAB-C13-C14-AC
Power Cord with C14 connector
CAB-SFP-50CM=
Catalyst 3560-E SFP Interconnect Cable, 50cm
Spare Rack Mount Kits for the Cisco Catalyst 3560-E Series
RCKMNT-E-1RU=
Rack Mount Kit (1RU) for Catalyst 3750-E and 3560-E
Cisco Catalyst 3560-E Relicensing for Used Equipment
LL-3560E-IPB=
IP Base SW Feature set license for Catalyst 3560-E Series
LL-3560E-IPS=
IP Services SW Feature set license for Catalyst 3560-E Series
Software Application Support Plus Upgrades Technical Services Contract
Product Part Number
Service Contract Number
3560E-IPS-LIC-B
Catalyst 3560-E IPS Upgrade from IP Base
3560E12D-SLB-QTY
IP Services for 3560E-12D, upgrade from IP Base
3560E12SD-SLB-QTY
IP Services for 3560E-12SD, upgrade from IP Base
For More Information
For more information about the Cisco Catalyst 3560-E Series Switches, visit:
http://www.cisco.com/en/US/products/hw/switches/index.html or contact your local account
representative.
Printed in USA
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
C78-377226-10
06/09
Page 23 of 23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising