3.0008.6010.9003 M3X TRITON英文说明书
书写纸，单色双面印刷，展开尺寸180*180毫米，折合尺寸60*90毫米
WARRANTY
Within 30 days of purchase: Return to retailer from which you purchased for repair or replacement.
Within 5 years of purchase: Return to Olight for repair or replacement.
This warranty does not cover normal wear and year, modifications, misuse, disintegrations, negligence, accidents, improper maintenance, or repair by anyone other than an Authorized retailer or Olight itself.
Technical Support Inquiries [email protected]
Customer Service [email protected]
Visit www.olightworld.com to see our complete product line of portable illumination tools.
M3X TRITON
VARIABLE-OUTPUT TAIL-SWITCH LED FLASHLIGHT
USER MANUAL
VER: 2014 . MAY 10, 2014 MADE IN CHINA
Thank you for purchasing the Olight M3X TRITON !
Please read this manual carefully before using this product.
INSIDE THE BOX
M3X Triton, Extended Tube, Battery magazine, (4)
O-rings, warranty card, user manual
BATTERY INSTALLATION ( Figure1)
Ensure batteries are inserted with the positive (+) end pointing to the head.
SUPPORTED BATTERIES
• If using 3xCR123A batteries. First, insert the batteries into the battery magazine, then place the battery magazine into flashlight, finally tighten the tail cap.
Attention that the positive of battery should towards the flashlight head.
• If usi ng 4xCR123A batteries or 2x18650 batteries, the extended tube need be assembled to the flashlight before battery installation.
Attentio n: 18650 batteries must be with protected board and protruding positive electrode
(18650 with flat positive electrode are not suitable for serial connect)
Figure1 Battery installation
Striking bezel
Head
CR123A
Body
Clip
Grip ring for clip
Tail cap
3 x CR123A gazine ry Ma Batte
Battery Magazine
Extended Tube
CR123A
CR123A
18650
4 x CR123A
CR123A CR123A
OR
2 x 18650
18650
CR123A
Tail switch
WARNING:
• Do not use unsupported batteries with
this flashlight.
• Cannot use flat 18650 batteries.
• Use caution on high outputs or long runtimes as
flashlight may get hot.
• Do not mix rechargeable and non-rechargeable
batteries.
• Do not mix batteries of different types/brands.
HOW TO OPERATE ( Figure2) a) Fully press then release the tail switch will enable or disable the output.
b) Chang e output brightness level through turning the head and body: each change from loose to tight, output
brightness circularly jump to next brightness level as low-high sequence. When turning off, the last
brightness will be memorized.
c) Under off status, lightly press the tail switch will perform momentary-on, while twice quick clicks will
activate high brightness and triple quick clicks will activate strobe, further hard press will acquiesce in
outputs.
Figure2 User interface a) OFF
OFF
Fully press
ON
On status
SPECIFICATIONS
OUTPUT & RUNTIME
HIGH
LOW
STROBE
LED
VOLTAGE
CANDELLA
BEAM DISTANCE
BATTERY TYPE
BODY TYPE
WATERPROOF
IMPACT RESISTANCE
DIMENSIONS
WEIGHT
1,200 LUMENS / 1.5 HRS
400 LUMENS / 7.5 HRS
1,200 LUMENS / 3 HRS
CREE XM-L2 CW
5V TO 15V
85,250 CD
584 METERS/ 735 FEET
3 or 4 x CR123A or 2 x 18650
TYPE III HARD ANODIZED ALUMINUM
IPX8 (UP TO 2 METERS)
2 METERS
L 211mm x (Head)D 63mm,(Tube)25mm
245 g/ 8.64 oz (excluding batteries)
Note: testing done with 2 x 18650 batteries(3.6V, 3400mAh）
All performance claims to ANSI/NEMA FL1-2009 Standard.
Fully press b)
OUTPUT VS RUNTIME ( Figure 3)
Figure3 Output VS Runtime
Low High
Change from loose to tight on status.
c) OFF
OFF
1
Slightly press
ON
Momentary Light
2
Slightly press
High
3
Slightly press
Strobe
Output ( lumen )
Ambient: Temp. 25℃ Humd. 55%RH
Battery: 2 x 18650@3400mAh Olight
High
1500
1200
900
600
300
0 15 30 45 60 75 90 105 120 135 150
Run Time (min)
