Servo Bracket User`s Manual

Servo Bracket User`s Manual
Servo Bracket
User’s Manual
V1.0
Sept 2009
Information contained in this publication regarding device applications and the like is intended through suggestion only and may be
superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or
warranty is given and no liability is assumed by Cytron Technologies Incorporated with respect to the accuracy or use of such information
or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Cytron Technologies’s products
as critical components in life support systems is not authorized except with express written approval by Cytron Technologies. No licenses
are conveyed, implicitly or otherwise, under any intellectual property rights.
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
Index
1. Introduction
1
2. Assemble Servo Holder and U joint
2
3. Dimension Drawing
9
4. Warranty
11
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
1. INTRODUCTION
Cytron Technologies has provide two types of servo bracket for their servo motor
which are servo holder and U joint. With the combination of these two type of brackets, any
creative shape and joint can be assembled just like Scorbot, biped and so on.
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
1
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
2. ASSEMBLE SERVO BRACKET AND U JOINT
This U joint and Servo Holder are suitable for C36 and C40 RC servo, for other type of servo,
user might need manual modification to use it.
This part will show example on how to assemble servo bracket and u joint to get creative
shape.
2.1 Assemble Servo Holder with RC Servo
1. Prepare the components as shown in Figure 1.
i.Servo Holder
ii.RC Servo
iii.Rivets
Figure 1
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
2
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
2. Mate the servo motors to servo holder with servo rivets as shown in Figure 2.
Figure 2
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
3
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
2.2 Assemble Servo Holder and U Joint with RC Servo
The following steps refer to figure below. This figure shows the bolts, nuts and screws that
are available in the servo bracket and U joint.
A B C Figure 3
1. Prepare the components as shown in figure below.
i. U Joint
ii. Servo horn
iii. C screw (refer Figure 3)
Figure 4
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
4
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
2. Mate the servo horns and U joints with C screw.
Figure 5
Figure 6
3. Prepare the components as shown in Figure 7.
i.
ii.
iii.
iv.
U Joint with horn in Figure 5
Servo holder
Bearing
A screw (refer Figure 3)
Figure 7
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
5
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
4. Mate servo bracket and U joints with bearing and A set screw.
Figure 8
5. Prepare the components as shown in Figure 9.
i. Servo holder and U joint in Figure 8
ii. Rivets
iii. RC Servo
Figure 9
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
6
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
6. Mate the servo motors to servo brackets with servo rivets as shown in Figure 10 until 12.
Position of servo motor is depends on user. But user need to ensure the servo motor is
mated at the middle position of their moveable range. As shown in figure below, a
successful mating is defined by the servo motors are nearly parallel to the servo holder
while the circuit and motors are turned on.
Figure 10
Figure 11
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
Figure 12
7
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
7. Mate the servo motor with B screw as shown in Figure 13.
Figure 13
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
8
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
3. DIMENSION DRAWING (unit in mm)
Servo Holder
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
9
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
U Joint
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
10
ROBOT . HEAD to TOE
Product User’s Manual – Servo Bracket
7. WARRANTY
¾
¾
¾
¾
Product warranty is valid for 6 months.
Warranty only applies to manufacturing defect.
Damage caused by mis-use is not covered under warranty.
Warranty does not cover freight cost for both ways.
Prepared by
Cytron Technologies Sdn. Bhd.
19, Jalan Kebudayaan 1A,
Taman Universiti,
81300 Skudai,
Johor, Malaysia.
Tel:
Fax:
+607-521 3178
+607-521 1861
URL: www.cytron.com.my
Email: [email protected]
[email protected]
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement