psm2397 installation instructions
INSTALLATION
INSTRUCTIONS
DISPLAY STATIC MOUNT
PSM-2397
Figure 1
(1) Plasma Static Mount
(6) M5 x 35mm Phillips Head Cap Screws
(4) .50 x .26 X 1.625” Nylon Spacer
(2) M5 x 75mm Socket Head Cap Screws
(1) Nylon Washer
(1) 10-24 Nylock Nut
(1) M4 Allen Key
(6) Mounting Buttons – Black Nylon
(2) .50 x .25 x 1.375” Nylon Spacer
(2) M5 x 70mm Phillips Head Cap Screws
(2) M5 x 90mm Socket Head Cap Screws
(1) Latching Flag
(1) 10-24 x .5 Flat Head Undercut Screw
BEFORE PROCEEDING: Unpack the carton, verify contents shown in Figure 1 and read
installation instructions completely. If you are missing any of the listed components, please contact
Customer Service at 1-800/582-6480.
CAUTION!
Displays are Extremely Fragile.
1. Attach latching flag to mount using the 10-24 Phillips flat head screw, Nylon washer, and
Nylock nut (see Figure 2 & Figure 3). Use proper holes depending on type of installation.
Tighten until friction will hold the flag in place.
Figure 2
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PKWY, STE. 700
SAVAGE, MINNESOTA 55378 USA
Figure 3
8805-000111 RevC
2004 Chief Manufacturing
www.chiefmfg.com
1/05
WARNING
ALL COMPONENTS MUST BE SECURELY FASTENED TO A
STRUCTURAL MEMBER CAPABLE OF SUPPORTING 4 TIMES
THE COMBINED WEIGHT OF ALL COMPONENTS PLUS THE
EQUIPMENT BEING MOUNTED. IF IT CANNOT SUPPORT
THIS WEIGHT, THE STRUCTURE MUST BE REINFORCED.
THE MAXIMUM WEIGHT TO BE INSTALLED ON THE MOUNT
IS 175 POUNDS (79.38 KG).
2. Remove screws securing table stand to display and remove table stand from display (see Figure 4 &
Figure 5).
Figure 4
Figure 5
NOTE: If installing display on Chief Mount without subwoofer, proceed to step # 6 (Page 3).
3. Remove four socket head screws, using M4 Allen key supplied, and subwoofer from table stand.
4. Secure subwoofer to back of display by sliding uprights into holes in display (see Figure 6 &
Figure 7).
Figure 6
Figure 7
5. Using M5 screws and nylon spacers, install mounting buttons on back of display (See
Figure 8 & Figure 9). Proceed to step 7 (page 3).
Figure 8
Figure 9
Page 2of 3
INSTALLATIONS WITHOUT SUBWOOFER
6. Using short M5 screws, install mounting buttons on back of display (See Figure 10 & Figure 11).
Figure 10
Figure 11
FOR ALL INSTALLATIONS
7. Securely anchor the static mount to wall studs or supporting framework (see WARNING).
8. Make sure the flag is lowered before attempting to place the plasma on the mount.
9. With the aid of another person, lift the plasma display up to the mount, align the mounting
buttons on the plasma with the teardrop slots in the mount, and set the plasma into place (see
Figure 12 or Figure 13).
10. Position (raise) the flag to secure the plasma.
With Subwoofer
Figure 12
Without Subwoofer
Figure 13
Page 3of 3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising