Hyper Mini Fisheye (Vandal-proof) IP Camera Quick_0

Hyper Mini Fisheye (Vandal-proof) IP Camera Quick_0
Hyper Mini Fisheye IP Camera Quick Guide
The Quick Guide is for quick installing and connecting the Hyper Mini Fisheye IP Camera. For more details, please
refer to the User’s Manual of the camera in the supplied CD.
NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check
the LAN connection.
Camera’s Connectors (Indoor Only)
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
Function Cable (Outdoor Only)
No.
Connector
1
Power
DC 12V
2
RJ-45
3
microSD Card Slot
Pin
1
2
-
5
Built-in microphone
1
2
3
4
5
6
7
-
6
Default Button
-
7
Speaker
-
4
Alarm & Audio I/O
Definition
Remarks
DC 12V
Power connection
Reserved
For network and PoE connections
Insert the microSD card into the card slot to store videos and snapshots.
Do not remove the microSD card when the camera is powered on.
Alarm Out +
Alarm Out Alarm connection
Alarm In +
Alarm In GND
Ground connection
Audio Out
Two-way audio transmission
Audio In
Audio In
Press the button with a proper tool for at least 20 seconds to restore the
system.
Audio Out
NOTE: It is not recommended to record with the microSD card for 24/7 continuously, as it may not be able to
support long term continuous data read/write. Please contact the manufacturer of the microSD card for
information regarding the reliability and the life expectancy.
No.
Connector
Pin
Pink
Green
Black
Red
1
2
3
4
-
1
Audio I/O
2
Power (DC 12V)
(2-Pin Terminal Block)
3
Alarm I/O
(4-Pin Terminal Block)
4
5
GND
RJ-45
-
microSD Card Slot
-
-
Default Button
-
Camera Cabling
Definition
Remarks
Audio In
Two-way audio transmission
Audio Out
DC 12V –
Power connection
DC 12V +
Alarm In –
Alarm In +
Alarm connection
Alarm Out –
Alarm Out +
GND
Ground connection
For network and PoE connections
Refer to the Default Button in the table under section Camera’s
Connectors (Indoor Only).
Refer to the microSD Card Slot in the table under section
Camera’s Connectors (Indoor Only).
Please follow the instructions below for cable connections.
Before Login to the Camera
Power Connection
Please use a DC 12V power adaptor and plug it to the camera and the power outlet. Alternatively, users can use an
Ethernet cable and connect it to the RJ-45 connector of the camera and a Power Sourcing Equipment (PSE) switch.
A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the
camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and
plug-ins or setting Internet’s security level to default. For further details, please refer to the User’s Manual in the
supplied CD.
NOTE: If PoE is used, make sure PSE is in used in the network.
Ethernet Cable Connection
Connect one end of the Ethernet cable to the RJ-45 connector of the camera, and plug the other end of the cable to
the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the
PC.
ActiveX Controls and Plug-ins Settings
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>, and click on <Custom level> to
change ActiveX settings.
Step 4: Set “ActiveX controls and plug-ins” items to
<Prompt> or <Enable>.
Step 1:
Step 2:
Step 3:
Step 4:
Internet Security Level
Start the Internet Explorer (IE).
Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Click on the <Security> tab and select
<Internet>.
Down the page, click <Default Level> and click
on <OK> to confirm the setting. Close the
browser window, and open a new one later for
accessing the IP camera.
Camera Login
The default IP address of the camera is: 192.168.0.250. Therefore, to access the camera for the first time, please set
the IP address of the PC as: 192.168.0.XXX; for example:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Login ID and Password
 Key in the camera’s IP address in the URL bar of the web browser window and hit on “Enter”.
 Enter the default username (Admin) and password (1234) in the prompt request dialogue. Note that username is
case sensitive.
Install the ActiveX Control
 After connecting to the camera, the request for installing the ActiveX control will appear just below the URL bar.
 Right click on the information bar, and then click on <Install ActiveX Control…> to permit ActiveX control
installation.
 In the pop-up security warning window, click on <Install> to start downloading Viewer software on the PC.
 Click on <Finish> after Viewer installation is completed.
Browser-based Viewer
The main page of the IP camera user interface is shown as the figure below. Please note that function buttons will
vary depending on the camera model.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising