LIT1205F CI-5 combined manual F.indd

REGULATORY COMPLIANCE
The Energy Star qualified Power Adapter has been tested for compliance with: UL, CSA and
CE.
WARRANTY POLICY
This product is warranted against failures due to defective parts or faulty workmanship for a
period of three years after delivery to the original owner. During this period, FSR will make any
necessary repairs or replace the unit without charge for parts or labor. Shipping charges to
the factory or repair station must be prepaid by the owner, return-shipping charges, via UPS
/ FedEx ground, will be paid by FSR.
This warranty applies only to the original owner and is not transferable. In addition, it does not
apply to repairs done by other than the FSR factory or Authorized Repair Stations.
This warranty shall be cancelable by FSR at its sole discretion if the unit has been
subjected to physical abuse or has been modified in any way without written authorization
from FSR. FSR’s liability under this warranty is limited to repair or replacement of the defective unit.
CI-5 BWPA
CI-5LB
FSR will not be responsible for incidental or consequential damages resulting from the use or
misuse of its products. Some states do not allow the exclusion of incidental or consequential
damages, so the above limitations may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
COMPUTER INTERFACE WALLPLATES WITH AUDIO
Warranty claims should be accompanied by a copy of the original purchase invoice
showing the purchase date (if a Warranty Registration Card was mailed in at the time of
purchase, this is not necessary). Before returning any equipment for repair, please read the
important information on service below.
OPERATIONS MANUAL
SERVICE
Before returning any equipment for repair, please be sure that it is adequately packed and
cushioned against damage in shipment, and that it is insured. We suggest that you save the
original packaging and use it to ship the product for servicing. Also, please enclose a note
giving your name, address, phone number and a description of the problem.
NOTE: all equipment being returned for repair must have a Return Authorization
Number (RMA). To get a RMA Number, please call the
FSR Service Department (973-785-4347).
Please display your RMA Number prominently on the front of all packages.
CI-5LB
CI-5BWPA
Contact Information:
FSR INC.
244 Bergen Boulevard,
Woodland Park, NJ 07424
PROPRIETARY INFORMATION
All information in this manual is proprietary to and the
property of FSR inc. This publication is protected by
the Federal Copyright Law, with all rights reserved.
No part of this document may be reproduced,
transcribed, or transmitted, in any form or by any
means, without prior explicit written permission
from FSR inc.
Tel: (973) 785-4347 · Fax: (973) 785-4207
E-Mail: sales@fsrinc.com · Web: http://www.fsrinc.com
43912
LIT 1205F
INSTALLATION AND OPERATION
Output Connector W iring
Balanced W iring
Unba lanced W iring
The 5 BNC output cable, 12 VDC power supply leads and audio leads should be prewired
through the duplex back box prior to completing the steps below. Do not plug in the
power supply until all wiring is completed and proper connections are verified.
+
SH
+
R
-
+
SH
+
R
L
L
Connect the 5 BNC female “pigtail” connectors to the 5 BNC male output cable leading to
the projector or monitor.
Unbalanced Input Conne ctor Pinout
Connect the audio output cables to the captive screw terminals labeled “Audio Out”. The
appropriate wiring configuration for balanced and unbalanced connections is shown in
Figure 1 to the right of this page.
Ring = Right
Tip = Left
Sleeve = G nd
Using the chart on the rear of the wallplate or below as a guide, set the cable equalization
dip switches for optimum performance at the desired cable length.
Connect the 12 VDC power supply stripped output leads to the captive screw terminals
labeled “9VAC” and “12VDC”. The units are NOT polarity sensitive. Attach the video input
from the desired source. Plug in the power supply. On the units face, an amber LED will
indicate power. The LED should change to green when a proper video signal is present on
the HD-15 input (horizontal sync is present).
Jum per
M ono Output Connector W iring
Balanced W iring
Unbalanced W iring
+
SH
+
R
-
+
SH
+
R
-
L
L
Jum per
SPECIFICATIONS
VIDEO INPUT
After confirming proper operation, unplug the power supply, and mount the CI–5 and cover
plate in the wall. Be certain that all cables and connectors are nested properly and check
for pinched or strained cables while mounting the CI-5 interface into the wall box. Use the
supplied screws for mounting. Install the cover plate with the supplied screws and perform
the final operational check.
Number/type:
Connectors:
Level (nominal):
Level (maximum):
Impedance:
VIDEO OUTPUT
Number/type:
Connectors:
Bandwidth:
Level (nominal):
Gain:
Impedance:
AMBER LED INDICATES
POWER IS PRESENT
GREEN LED INDICATES
HORIZONTAL SYNC IS
PRESENT ON THE VIDEO
INPUT
1 VGA / SVGA / XGA / SXGA / UXGA / RGBHV / RGBS / RGsB / RsGsBs
One 15 pin HD female
Analog 0.7v p-p
2v p-p
75 ohms
1 VGA / SVGA / XGA / SXGA / UXGA /
RGBHV / RGBS / RsGsBs
4” Pig-tail of 5 female BNC’s ( RGBHV )
700MHz @ -3.0dB (5 BNC output)
400MHz @ -3.0dB (HD-15 loopback output)
Unity / User adjustable via DIP switch settings
OFF = 0’ to 75’ LOW = 75’ to 125’
MEDIUM = 125’ TO 175
HI = 175’ to +200’
75 ohms
AUDIO
CI-5BWPA/CI-5LB
PCI-5BWPA
Bandwidth:
THD + Noise:
Noise Floor:
Stereo separation:
Audio Gain
20 Hz to 20 kHz (+/-0.05dB)
0.01% @ 20 kHz at rated Max Output S/N >98dB
Better than 98dB
-90dB @ 1 kHz
+6dB
100 Hz to 15kHz (+/-2dB)
0.5% between 275 Hz-3.5kHz
NA
-40dB @ 1kHz
0dB with 1.5dBm max insertion loss
1 stereo unbalanced
1/8” mini connector
10K ohms DC coupled unbalanced
+6dBm
1 stereo unbalanced
1/8” mini connector
600 ohms
+20dBm
1 Balanced / Unbalanced Stereo
5 Position Captive screw terminal
50 ohm
600 ohms: +12dBm Balanced / +6dBm Unbalanced
Hi – Z: +14dBm Balanced / +8dBm Unbalanced
1 Balanced / Unbalanced Stereo
2, 3 position captive screw terminals
AUDIO INPUT
Number/type:
Connectors:
Impedance:
Max level:
AUDIO OUTPUT
Number/type:
Connector:
Impedance:
Maximum Level:
600 ohms
+20dBm
SYNC
Input level:
Output level:
Input Impedance:
Output impedance:
Polarity:
Horizontal frequency:
Vertical frequency:
2.0v to 5.0v p-p
TTL to 5.0v p-p
475 ohms
75 ohms
Positive or negative
15kHz - 200kHz
30 Hz - 150 Hz
GENERAL
DIP SWITCH
SETTINGS
OFF
LOW
MED
HIGH
POSITION
S2
S1
0
0
0
1
1
0
1
1
OPTIMAL CABLE
LENGTH (FT)
50
100
150
200
ACCEPTABLE CABLE
RANGE (FT)
0-75
75-125
125-175
175-200
Power:
Mounting:
Colors:
Enclosure Type:
Size:
Approvals:
CI-5
VDC
@80.09
9v ACmodel:12
/ DC, 50/60
Hz:
– 14vADC, 9v AC Power Supply
included.model:12
May be remotely
located
150 feet away from
CI-5LB
VDC @ 0.125
A up to 200
the wallplate when using 22 Gage / 2 Conductor cable.
Single – Gang Decora Wallplate ( Included )
Black, White, Ivory
Metal
4.094” H x 1.706” W x 0.65” D
UL / CE
Jum per

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project