Bellman Visit 868 Door
 Technical Solutions BE1410
Bellman Visit 868 Door
Transmitter
BE1410
Introduction
Thank you for choosing products from Bellman & Symfon.
The Bellman Visit 868 System consists of a number of radio transmitters and
receivers. The transmitters detect different events in the surrounding area and
transmit a radio signal to the receivers. The receivers pick up this signal and
provide indications using light, sound and/or vibration.
The transmitter determines what type of light, sound or vibration should be
displayed so that the reason for the indication is evident.
Read through the entire user manual first and then start to install the system.
Refer to the illustration of the Bellman Visit 868 System on the inside of the
cover.
Getting started
Unpacking, installing and testing the unit
1. Open the battery cover (3). Fit one 9V battery, either a 6LR61 alkaline or
6F22 lithium type battery, and close the battery cover.
2. Press the Test Button (2). The Bellman Visit 868 Door Transmitter lights
up the LED (1) to indicate that the unit is transmitting a radio signal. The
Bellman Visit 868 receivers will indicate the Door Transmitter. The Door
Transmitter waits until it has been quiet for two seconds in order to avoid
acoustic feedback.
3. The Bellman Visit 868 Door Transmitter should be placed on the wall
or door no more than 3 cm from the doorbell. The door transmitter is
mounted either suspended on the wall mount bracket (5) on the screw
supplied or using the self-adhesive Velcro tape, see illustrations 1-3 below.
If the Velero tape is used, the wall can be cleaned using the enclosed wet
wipe.
O
4
TENA
Technical information
Power supply
Battery power:
9 V 6LR61 alkaline -
9 Y 6F22 lithium
Operating time:
ÓLRO] alkaline: approximately 5 years
6F22 lithium: approximately 10 years
Power consumption: Active: < 30 mA
Idle position: < 10 pA
Radio function
Radio frequency: 868.3 MHz
Number of Radio Keys: 64 Radio Keys
as standard. Special software can be used
to increase these to 256 Radio Keys in
increments of 64 per software purchase,
Contact the nearest supplier for furcher
information.
Coverage: The normal coverage between a
transmitter and receiver in the Bellman
Visit 868 System is approximacely 200
metres with a clear line of sight, Coverage
is reduced if walls and large objects screen
off the signals. Any thick walls constructed
of reinforced concrete will greatly affect
coverage. The system may also be affected by
radio transmitters, such as TV transmitters,
computers, mobile phones, etc, This means
that a unit may work perfectly in one part of
the room but not at all in another.
Activation
Via test button
Via internal microphone
Via external microphone
Via built-in magnetic coif
Additional information
For indoor use only
Size Bx H x D: 80 x 145 x 36 mm
Weight: Wich battery: 190
Without battery: 155 ¢
Colour White with a red triangle.
Accessories
BE9199/BE9200 Bellman External Door
Microphone
Page 4 AN BE1410 a Technical Solutions
Function
General
The BE1410 Bellman Visit 868 Door Transmitter is a radio transmitter within the Bellman Visit 868 System for
indoor use, which recognises the sound emitted by a doorbell.
The door transmitter is activated by the built-in microphone, via electromagnetic fields or via a BE9199/BE9200
Beliman External Door Microphone (accessory). On delivery the Door Transmitter is set to standard detection,
which is suitable for most doorbells.
The BE1410 Bellman Visit 868 Door Transmitter is suitable for use with a doorbell which gives a clear tone without
any significant and rapid variations in sound. If the doorbell is electromechanical, the Door Transmitter also detects
the electromagnetic field emitted by the doorbell. It is important that the Doorbell emits a detectable sound so that
the door transmitter does not misinterpret it as speech, music, a vacuum cleaner or something else one does not
want the door transmitter to respond to.
If there are difficulties in getting the Door Transmitter to respond to the doorbell, a BE9199 or BE9200 Bellman
External Door Microphone can be used instead of the Door Transmitters internal microphone,
If the current doorbell, door telephone or telephone sound is difficult to detect even with the External Door
Microphone, we recommend using a different solution. Other conceivable solutions are the BE1420 Bellman Visit
868 Pushbutton Transmitter or BE1430 Bellman Visit 868 Telephone Transmitter,
The Pushbutton Transmitter is a transmitter that can be placed on the outside of the door and this means that a
normal doorbell is not required.
The Telephone Transmitter is a multiway transmitter which can be connected electrically to an existing doorbell.
This cannot be done with all doorbells, door telephones or telephones.
Using the Bellman External Door Microphone BE9199/BE9200
If the BE9199/BE9200 Bellman External Door Microphone is used, the Bellman Visit 868 Door Transmitter can
detect the difference between the sound coming from the internal microphone and the external door microphone.
Using this function, the Door Transmitter can transmit different signals depending on which microphone the
sound is coming from. The External Door Microphone can, for example, be used for a doorbell with a sound that is
difficult for the internal microphone to detect, a door telephone or a telephone.
Please note: Do not place the Door Transmitter too close to the External Microphone since the internal microphone
may interfere with the External Microphone.
lt is important for the doorbell, door telephone or telephone to emit a loud enough sound, so that other loud
sounds in the vicinity do not deceive the Door Transmitter into believing thar it is the doorbell, door telephone
or telephone. The sensitivity of the External Door Microphone can be adjusted using the training function and
this allows adjustments to be made to the doorbell, door telephone or telephone, It is important to carry out this
adaptation to ensure that the Door Transmitter operates as well as possible.
Sound training
The BE 1410 Bellman Visit 868 Door Transmitter can be sound trained from a maximum of three different
sound sources. The advantages of this are mainly that the Door Transmitter will be able to give a different
indication according to which sound source activates it, but also that this function will help to ensure that the Door
Transmitter is only activated by the desired sound source.
The Bellman Visit 868 Door Transmitter has three training options, two for the internal microphone and one for
the external microphone.
The requirements for a Door Transmitter to detect a sound is that it sounds in the same way every time, that it is
long enough and that it does not vary too rapidly.
Normal
Int, Mic 1
Int. Mic 2
Ext, Mic
Technical Solutions BE1410 // . Page5
Proceed as follows to program a sound:
1. Change the Programming Switch (8) from Normal to the desired position, Int. Mic. 1, Int. Mic. 2 (for
detection via the internal microphone) or Ext. Mic, (for detection vía a Bellman External Door Microphone).
Place the Door Transmitter near to the doorbell that is to be trained to it.
Make sure that it is quiet.
Press the Test Button (2). :
The LED (1) lights up yellow to indicate that the Door Transmitter is in training mode and is waiting for the
sound that it is to be trained for. -
Activate the doorbell.
. The LED (1) will now blink green while the Door Transmitter analyses the sound.
8. If the training is accepted, the LED (1) will light up green. Some sounds are difficult to analyse and therefore
difficult to detect afterwards. Therefore always check to ensure that the Door Transmitter is detecting the
doorbell correctly after training, If this does not work, refer to the next step.
9. If the sound cannot be analysed, the LED (1) will light up yellow. You can try to train for the sound again by
repeating steps 1 to 6. If it still does not work, the doorbell has a sound that the Door Transmitter cannot
analyse, In this case tty to change the doorbell sound if it has this option and then repeat steps 1 to 6, If that
does not work either, test by using an External Door Microphone and then repeat steps 1 to 6.
10. Reset the Programming Switch (8) to Normal position.
11. The Bellman Visit 868 Door Transmitter is now ready to use,
> EP
o
It no sound is programmed with the training function, standard detection is used which works in most cases.
Resetting the trained sound
Proceed as follows to remove a trained sound:
Change the Programming Switch (8) from Normal to the position to be deleted.
Hold in the test button (2). The LED (1) will light up yellow.
When the LED (1} lights up green, deletion is complete.
Reset the Programming Switch (8) to Normal position.
The Bellman Visit 868 Door Transmitter is now ready to use.
AAN
If you wish to use standard detection for incoming sound via the internal microphone, both Int. Mic. 1 and Int.
Mic. 2 must be deleted.
Radio key
On delivery all Beliman Visit 868 units are tuned to the same Radio Key. If you have a neighbour with a similar
system, you can change to different Radio Keys so that you do nor affect each other's systems. All units in a system
must have the same Radio Key. If you use the Radio Key Switch (7) to change the Radio Key on this transmitter,
you must also change all other units in your Bellman Visit 868 System to the same Radio Key. Refer to the user
manual for the relevant unit,
Indicators and Signals
System indicators
When the LED (1) lights up, the Door Transmitter transmits radio signals.
Power supply
When the Door Transmitter is activated, the LED (1) normally lights up green. This means that the battery is
in good condition.
If the LED (1) lights up yellow, this means that the battery is flat and must be changed. Only use a 6LR61
(alkaline) or 6F22 (lithium) type battery.
PE EE Sdn
4
Page 6 \ BE1410
Fault warning
The LED (1) flashes yellow when the Door Transmitter is exposed to high noise levels or an electromagnetic field for
longer than 15 seconds. If the LED blinks even when there is no noise, the reasons may be:
Technical Solutions
1. Tt is located in a constant electromagnetic field.
2. The microphone fitted in the external microphone socket (9) is faulty.
Troubleshooting in brief
Problem Solution
Nothing happens when the transmitter ic activated with the | * The Door Transmitter waits un til ic has been quiet for two seconds in
Test Burton (2). order to avoid acoustic feedback. Try again.
+ Change the battery. Only use an alkaline 6LR61 or a lithium 6F22
type battery.
The LED (1) lights up yellow when the Door Transmitter is | * Change the battery. Only use an alkaline 6LRG1 or a lithium 6F22
activated. type battery.
The LED (1) lights up green when the Door Transmitter is e Check the battery in the receiver. -
activated, but the receivers arc not signalling. » Check that the receivers are not placed too far away by moving them
The LED (1) blinks yellow closer to che transmitter.
» Checle that che Door Transmitter is ser to the correct Radio Key. Yor
further information sec Function/Radio key.
The LED (1) blinks yellow + Make sure that it is quiet by the Door Transmitter,
« Turn off the magnetic coil if an electromagnetic field from an
inductive loop, ctc., is causing a fault to be indicated.
« Disconnect the External Microphone in case a faulty microphone is
connected.
The doorbell rings but the Door Transmitter is not activated. | * Move the Door Transmitter around the doorbelt both closer and
further away. The normal distance is about 3 cm from the doorbell.
* Ty to train the Door Jransmaitter with the relevant doorbell sound.
For further information see Function/Sound training,
+ Does the doorbell have a ring signal which varies significantly
in strength and/or tone? In this case it may be difficult to detect
this doorbell using the training function. Try resetting the Door
Transmitter to standard. For further information see Function/
Resetting the trained sound.
* Rectify the problem as indicated in the descriptions under Function/
Cencral and Function/Using the Bellman External Door Microphone
BE9199/BE9200
The receivers in the system transmit signals for no reason. . Change the Radio Key on all units in the system. For
further information see Function/Radio key
. Try to train che Door Transmitter with the relevant
doorbell sound. For further information sec Function/Sound training.
. Rectify the problem as indicated in the descriptions under
Function/General and Function/Using the Bellman External Door
Microphone BE9199/BE
For further information about the product in English, refer to the Appendix.
| Technical Solutions
®
868; more ets
N | |
1. LED. Combined transmission
and battery indicator. For further
information see Indicators and
Signals
‘Test button/pushbutton
Battery cover
Microphone
Wall mount bracket
Signal switch
Radio key switch
о ал к
Programming switch which should remain in
the “Normal” position
External microphone socket
>
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising