Intelligent Recording Universal Adapter 3.0 – Quick Setup Guide

Intelligent Recording Universal Adapter 3.0 – Quick Setup Guide
Intelligent Recording
Universal Adapter 3.0 – Quick Setup Guide
Check The Package Contents
1 – USB Connector to PC.
2 – Line Selector – Default is L1 and should not be changed.
3 – Handset A/B Switch – Default is A.
See the Installation Manual for use of this switch.
4 – Handset Connection Indicator – lights when handset is connected and
properly configured.
5 – Handset 1/2 Switch – Default is 1.
See the Installation Manual for use of this switch.
6 – Handset In Port – Connect the curly cord of the handset to this port if
using in handset mode.
7 – Handset Out Port – Using the supplied short handset cable, Connect
from this port to the telephone where the handset curly cord was
connected if using in handset mode.
8 – Phone Port – Connect the phone to this port if using in Line Mode.
9 – Line Port – Connect the phone line to this port if using in Line Mode.
-
1 x Universal Adapter 3.0
1 x Line cord
1 x Handset cord
1 x Quick Reference Install Guide (this document)
1 x USB PC Cable
Choose How To Connect
The Universal Adapter 3.0 (UA3) can connect to your telephone in 2 ways:

Line Mode: Where the UA3 is connected directly to an analog telephone line.
This method should be used if you have a single analog phone line.

Handset Mode: Where the UA3 is connected to the curly cord (telephone
handset cord) of your telephone. This connection is used to record digital, IP,
or multi-line telephones.
If you have a standard analog telephone that connects to a home phone line, or an analog
extension behind a PBX (this includes desktop and cordless phones), you should use the
Line Mode Connection method.
Install the Software
Download the UA3 software from our website at the link below:
Contact Intelligent Recording
Visit Our Website at www.usbcallrecord.com
Phone:
US and North America 800-930-8135
UK and ROW +44 (0) 1909 512 148
Email: support@irl-recording.com
http://www.usbcallrecord.com/index.php/pages/downloads/
Scroll down on the page until you see the section for XTR Universal Adapter 3.0. The
software to be downloaded is Version 3.0.2.26 Universal Adapter 3.0 Software Download.
Once downloaded install the software.
You can also download the complete Installation Manual and Users Guide which will step
you through the Setup Wizard.
Intelligent Recording
Universal Adapter 3.0 – Quick Setup Guide
LINE MODE CONNECTION
HANDSET MODE CONNECTION
Handset mode connection is used when you cannot connect to an analog telephone line
directly. Examples of when you need to use handset mode are on Digital PBX telephones,
IP telephones and Multi-Line telephones.
Disconnect the telephone line cord from the base of your
telephone (the other end connects to wall socket) and plug this
into the Universal Adapter 3.0 “Line” port. Connect the long cord
supplied between the Universal Adapter3.0 and the socket on your
phone (where you removed the line cord). NOTE: The Universal
Adapter 3.0 will record calls when connected to the phone line, it
is not required that the telephone be connected to the device.
Using the Setup Wizard
After you have installed the software the Setup Wizard will
automatically launch – this Wizard will allow you to configure
the software for the type of connection you are using. Please
consult the Installation Manual for using the Setup Wizard
To connect in handset mode, simply remove the curly cord from your telephone base and
connect into the Universal Adapter 3.0 “IN” port and connect the short handset lead
supplied between the telephone handset socket and the Universal Adapter 3.0 “OUT” port
as shown above.
If you are using a headset the audio path of the headset has to pass through the Universal
Adapter 3.0 to the telephone in order to record from the headset.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising