MS10L/MS12L - Rockville Audio

MS10L/MS12L - Rockville Audio
OWNER’S MANUAL
RockvilleAudio.com
© 2016 ROCKVILLE // Features and specifications are subject to change and or improvement without notice
MS10L /MS12L
Marine/Boat Subwoofer with LEDs and Remote
The Rockville MS-L series marine subwoofer is one of the most powerful on the market. What really
makes this sub stand out is the sound quality and durability. The frequency range of these subs is so
good that it will make all your songs sound so much better! These play frequencies that normal full
range speakers cannot hit adding depth and richness to all your music. We added an awesome LED
lighting system to these subs to really make your system shine. Our LED subs feature 19 dynamic
modes, 20 switchable static colors, strobe effect, speed, and brightness settings. They are all adjusted through the remote. There is also demo mode that will run through 9 dynamic programs and
repeat. The MS-L series subwoofer was designed in a molded ABS plastic basket made with a
special blend that is waterproof and un-breakable. You can literally jump on it and hit it with a sledgehammer without it breaking!
Using only true marine grade components and materials, the Rockville MS10LW subwoofers are fully
marinized against salt & fresh water conditions. These subs are completely waterproof and protected
from the elements! They are UV treated and have a special waterproof coating to prevent water
damage.
Please read this guide carefully for proper use of your Rockville MS-L series marine subwoofer.
Should you need technical assistance please call our technical help line at 1-646-758-0144, Monday
through Friday, 9am to 5pm EST.
Features/Specifications
LED Wiring Instructions
1. Connect the red cable of the included LED power harness to the positive (+12V) terminal of your
power supply. Connect the black cable to the negative terminal of your power supply.
2. Connect the male end of the harness to the corresponding female end protruding from the back
speaker near the terminals.
CAUTION!
DO NOT SHORT CIRCUIT THE LED OUTPUT, THIS MAY LEAD TO PERMANENT DAMAGE!
Remote Control Functions
1. Power/Standby: Press this key to turn on LEDs or switch to
standby mode.
2 . Dynamic Mode: Switch from dynamic mode to color mode
or switch between dynamic modes.
1
2
3. Dynamic Mode Speed: Use these buttons to adjust dynamic mode speed. If the unit is in static mode, pressing these
buttons will switch unit to dynamic mode.
MS10L
MS12L
• Max power: 2400 Watts
• Max power: 2800 Watts
• RMS program power: 1200 Watts
• RMS program power: 1400 Watts
• RMS power: 600 Watts
• RMS power: 700 Watts
• Polypropylene cone with rubber edge
• Polypropylene cone with rubber edge
• 2.0˝ 4 Layer dual voice coil
• 2.0˝ 4 Layer dual voice coil
• Molded ABS plastic basket made with a special
blend that is water proof and unbreakable
• Molded ABS plastic basket made with a special
blend that is water proof and unbreakable
• Cool LED lighting effects with remote control
• Cool LED lighting effects with remote control
• Magnet 80oz double stacked magnet
• Magnet 80oz double stacked magnet
• Frequency response: 30Hz – 4Khz
• Frequency response: 20Hz – 4Khz
Connection Diagram
• Impedance: Dual 4 ohms
• Impedance: Dual 4 ohms
One 4 ohm DVC woofer with a 2 ohm load
• Sensitivity: 90dB
• Sensitivity: 90dB
• Total diameter: 10.6˝
• Total diameter: 12.8˝
• Cutout diameter: 11.4˝
• Cutout diameter: 11˝
• Total height: 7.2˝
• Total height: 7.7 ˝
• Mounting depth: 5.6˝
• Mounting depth: 6.1˝
3
4. Static Color Adjust: Use this button to switch between
static colors. Pressing these keys while in dynamic mode will
switch the unit to static mode.
+
SPEED
DEMO
SPEED
COLOR
MODE
BRIGHT
–
+
4
–
COLOR
3
–
+
5
BRIGHT
–
5. Brightness Adjust: Pressing these buttons will adjust brightness while in static mode. If the unit is in dynamic mode,
pressing these buttons will switch the unit to static mode.
10
MODE
–
2
6. Demo Mode: This button will place the unit in demo mode.
While in demo mode, unit will loop through 9 of the dynamic
modes with each repeating 3 times.
One 4 ohm DVC woofer with an 8 ohm load
ATTENTION:
4Ω
4Ω
4Ω
4Ω
BRIDGED
WIRE
2Ω
8Ω
Installation
1. Find a mounting location that does not interfere with the safe operation of your vessel. Make sure
mounting screws will not puncture wiring harnesses, control cables, hydraulic lines, fuel lines, the fuel
tank or the hull. These may be located behind or under the mounting surface.
Two 4 ohm DVC woofers with a 1 ohm load
4Ω
4Ω
4Ω
4Ω
Two 4 ohm DVC woofers with a 4 ohm load
4Ω
4Ω
2. Create a mounting template using the provided measurements and place it on the desired surface.
Using a jigsaw or rotary cutting tool, cut along the line denoting the mounting hole. Use a drill to drill
the holes for the mounting screws.
3. Remove the grill. Connect your pre-routed speaker cables to the woofer. Insert the woofer into the
mounting hole, align the mounting screw holes, insert the screws and tighten them. Be sure to not
over tighten. To replace the grill, press and turn clockwise (to the right).
1Ω
4Ω
4Ω
4Ω
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising