To reset the lock to factory default, see the following

To reset the lock to factory default, see the following
Industry Canada:
Canadian ID: 6982A-YRHCPZW0 (Z-Wave); 6982A-YRHCPZB0 (Zigbee)
This Class B digital apparatus meets all requirements of the Canadian Interference Causing
Equipment Regulations. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne
causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce
dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle
interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
For the U4A-YRHCPZB0 and 6982A-YRHCPZB0, the following statement applies:
“This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator and your body. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.”
Section 7.1.2 of RSS-GEN Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
En vertu des règlements d'Industrie Canada, cet émetteur radio ne peut fonctionner avec une antenne
d'un type et un maximum (ou moins) approuvés pour gagner de l'émetteur par Industrie Canada. Pour
réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être choisies
de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire
pour une communication réussie.
Section 7.1.3 of RSS-GEN This Device complies with Industry Canada License-exempt RSS standard(s).
Operation is subject to the following two conditions: 1) this device may not cause interference, and 2)
this device must accept any interference, including interference that may cause undesired operation of
the device.
Cet appareil est conforme avec Industrie Canada RSS standard exemptes de licence(s). Son
fonctionnement est soumis aux deux conditions suivantes: 1) ce dispositif ne peut causer des
interférences, et 2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent
causer un mauvais fonctionnement du dispositif.
INTRODUCTION
The Yale Real Living™ Stand-alone Push Button Deadbolt Lock combines a robust lockset with a
contemporary electronic aesthetic.
Users benefit from a push button keypad that makes day-to-day access effortless for simple updates
to user information in the event of staffing changes or security breaches. Yale Real Living™ is engineered for quick and easy installation and fits in place of a standard deadbolt lock door prep (ANSI/
BHMA A156.115).
If this is an RF-enabled network lock, it needs to be located within 50 - 100 feet of another network
controller. That distance is influenced by objects between the lock and the controller and may be
expanded depending on proximity to other RF network devices. Also, if the lock is connected to a
network controller, it is recommended that it is programmed through the centralized user interface
(PC or hand-held device) to ensure communication between the lock and the controller unit.
3
P/N AYRD210-INST-FUL REV C
An ASSA ABLOY Group brand
PREPARE LOCK FOR INSTALLATION
Unpack the Lock
The lock is packed representative of how it will install on
the door.
Before installing the lock on the door:
A. Inside escutcheon
1. Loosen the screw (Phillips #2) holding the battery cover. (The screw remains attached to battery cover)
2. Slide the battery cover up and out (note the two tabs at bottom of battery cover).
3. Remove the inside mounting plate (with gasket) from the back (door side) of the inside escutcheon.
Battery Cover
2
Inside Escutcheon
1
a.Ensure that gasket
on Inside Mounting
Plate is properly
fitted. Note the
positioning of the
gasket's five rubber
nubs (Figure 3A) .
Inside Escutcheon & Mounting Plate
(with gasket)
Figure 3A
3
B. Bolt
Note: Bolt ships with backset in 2-3/8" position. If required, press small black button on
underside of bolt and pull to extend to 2-3/4"
backset position (Fig. 3B).
Figure 3B
C. The outside escutcheon (with gasket) remains assembled.
Outside Escutcheon
5
P/N AYRD210-INST-FUL REV C
An ASSA ABLOY Group brand
Status Indicators
1
2
Low Battery Warning
RED
3
Lock-out Mode
RED &
BLUE
Return to previous step
BLUE
Definitions
All Code Lockout Mode: This feature is enabled by the Master code. When enabled, it restricts
all user (except Master)PIN code access. When attempting to enter a code while the unit is in
Lockout, the Status Indicator flashes RED and BLUE (8 times); the keypad flashes as well.
Audio Mode: Choosing Disable (3) in Audio mode shuts off the code confirmation tone playback for use in quiet areas. Audio mode is enabled or disabled through feature programming by
the Master code.
Automatic Re-lock Time: After a successful code entry and the unit unlocks, it will automatically re-lock after a default of thirty (30) seconds. Re-lock time is adjustable** from
10 - 240 seconds.
Inside Indicator Light: Shows active status (Locked) of lock and can be enabled or disabled in
the Advanced Lock Settings (Main Menu selection #3).
Low Battery: When battery power is low, the Status Indicator flashes RED. If battery power is
completely lost, use the key override.
Master PIN Code: The Master PIN code is used for programming and for feature settings.
It must be registered prior to programming the lock. The Master code will also operate
(unlock/lock) the lock.
Network Module Setting: With the optional Network Module installed, this setting becomes available through the Main Menu (7) and allows the lock to connect with a network controller.
One Touch Locking: When the latch is retracted, activating the keypad will extend the latch (during Automatic Re-lock duration or when Automatic Re-lock is disabled).
Privacy Mode Button: Pressing and holding the Privacy button (found below thumbturn) for a duration of four beeps deactivates the keypad, and because it is set from the inside, provides a secure lock for the convenience of the occupant(s).
Shutdown Time: The unit will shutdown for a default of sixty (60) seconds and not allow operation after the wrong code entry limit has been met. When the unit is in Shutdown, the Status
Indicator flashes RED and BLUE; the keypad flashes as well.
Tamper Alert: Audible alarm sounds if attempting to forcibly remove outside lock from door.
User PIN Code: The User code operates the lock. Maximum number of user codes is 250 with
Network Module; without Network Module, maximum is 25 user codes.
Wrong Code Entry Limit: After a specified number of unsuccessful attempts at entering a valid
PIN code the unit will shut down and not allow operation. Wrong code entry limit is adjustable
from one (1) to ten (10) times**. With no RF network enabled - default is 5; 10 with RF network
enabled.
**Adjustable only when using Network Module
9
P/N AYRD210-INST-FUL REV C
An ASSA ABLOY Group brand
To reset the lock to factory default, see the following:
Reset Lock to Factory Default
The following procedure returns the lock to its factory defaults
by deleting all user codes (including the Master PIN code*) and
returning all programming features to their original default settings
(see below).
Reset Button
Cable
1. Remove the batteries and then remove the interior escutcheon
to access the reset button.
2. The reset button (see image at right) is located above the PCB cable connector.
3. Hold down the reset button for a minimum of 3 seconds and
then reinstall the batteries; once the batteries are properly
installed, release the reset button.
All features, including adjustable settings** (see below) should now be returned to factory default.
Upon reset, Master Code Registration is the only option available
and must be performed prior to any other programming of the lock.
Inside Escutcheon
See "Operation" in this manual for programming instructions.
Factory Default Settings
Settings
Factory Default
Master PIN Code
Registration required*
Automatic Re-lock
Disabled
Inside Indicator Light
Disabled (Off)
One Touch Locking
Enabled
Audio
Enabled
Privacy Mode
Disabled
Automatic Re-lock Time
**30 Seconds
Wrong Code Entry Limit
**5 Times
Shutdown Time
**60 Seconds
*The Master PIN code must be registered prior to any other programming of the lock.
**Adjustable only when using Network Module
11
P/N AYRD210-INST-FUL REV C
An ASSA ABLOY Group brand
Feature Programming Through Menu Mode Using Master PIN code*
1. Enter the 4-8 digit Master PIN code followed by the
key.
2. Enter digit corresponding to the function to be performed followed by the
key.
Note: If the lock is connected to a network controller, it is recommended that it is
programmed through the centralized user interface (PC or hand-held device) to
ensure communication between the lock and the controller unit.
*The Master PIN code must be registered prior to any other programming of the lock.
1
M
User Number (UN)
2
Master PIN Code Setting
User PIN Code Registration
ƒƒ 1~25: without network module
M
ƒƒ 1~250: with network module
U
Register
Delete
Advanced Lock Settings
Automatic Re-lock
Default settings
in bold.
Enable
Disable
Inside Indicator Light
Enable
Disable
One Touch Locking
Enable
Disable
Privacy Button Setting
Enable
Disable
Handing the Lock
Audio Mode
Performs automatic handing
of the lock.
Enable
Disable
For quiet areas, select Disable (3)
in Audio Mode.
N/A
All Code Lockout Mode
Enable
Disable
**Network Module Setting
**This function appears only
with RF network module
installed.
Join the network
Exit the network
Note: If the lock is connected to a network controller, it is
recommended that it is programmed through the centralized
user interface (PC or hand-held device) to ensure communication between the lock and the controller unit.
13
P/N AYRD210-INST-FUL REV C
An ASSA ABLOY Group brand
Programming Troubleshooting
Symptom
Suggested Action
Lock does not respond – door is
open and accessible.
•
•
•
•
Press each keypad button to see if they respond when pressed.
Check batteries are installed and oriented correctly (polarity) in the battery case.
Check batteries are in good condition; replace batteries* if discharged.
Check to see if cable is fully connected and not pinched.
Lock does not respond – door is
locked and inaccessible.
•
•
•
Lock may be in Privacy mode (set from inside room). Key will grant access.
Batteries may be completely discharged.
Use mechanical key to gain entry and replace batteries*.
Unit chimes to indicate code acceptance, but the door will not open.
•
•
•
Check to see if there is another locking device on the door.
Check the door gaps for any foreign objects between door and frame.
Check that the cable is firmly connected to the PC board.
Unit operates to allow access, but will
not automatically re-lock.
•
•
•
Check to see if Auto Re-lock Mode is enabled.
Disable Auto Re-lock Mode to lock the door (automatically).
If low battery indicator is lit (see below), change batteries*.
PIN codes will not register.
•
•
•
•
•
•
PIN codes must consist of 4 to 8 digits to register.
The same PIN code cannot be used for multiple users.
Registration/management of PIN codes is set by the authority of the Master Code.
Contact the Master user.
User codes must be entered within 5 seconds or the process will have to be restarted.
The star
(*) or pound
(#) cannot be used as part of the PIN code.
Upon entering a PIN code and pressing the star (*) key, the lock gives
a series of beeps, flashes red and
blue LEDs seven times, and does not
unlock.
•
•
•
All Code Lockout Mode is enabled.
Only the Master can enable/disable All Code Lockout Mode.
Contact the Master user.
Upon entering a PIN code and pressing the (*) key, there are different
tones.
•
•
Check to see if the lock is set to All Code Lockout Mode.
Setting/managing All Code Lockout Mode is done through Master Code only. Contact
the Master user.
The unit operates, but it makes
no sound.
•
Enable Audio Mode.
The unit displays intermittent RED
flashes.
•
This is the Low Battery indicator alerting that it is time to replace the batteries. Replace
all four (4) batteries* with new AA Alkaline batteries.
Upon entering a PIN code and pressing the star (*) key, the unit responds
with a series of beeps and the keypad
flashes three times.
•
The digits entered were incorrect or incomplete. Re-enter the correct code followed by
the star
key.
* When batteries are replaced, Network Module locks have a real time clock that will be set through the User Interface (UI); it
is recommended to verify correct date and time particularly those locks operating under Daylight Saving Time (DST).
** Network Module locks only
15
P/N AYRD210-INST-FUL REV C
An ASSA ABLOY Group brand
How to Replace or Install Cylinder
1. Remove cylinder:
A
A. Remove outside escutcheon from door.
B. Remove rubber gasket.
C. Remove two screws holding plastic guide
in place.
B
D. Remove plastic guide.
E. Remove screw with washer holding cylinder in
place (visible after plastic guide is removed).
F. Remove cylinder housing by pulling towards the
door side of escutcheon.
Before installing cylinder, please be sure you have
correct length tailpiece.
2. Install new cylinder:
A. Reverse previous steps for removing cylinder.
D
C
E
F
Cylinder and tailpiece information:
L
1-3/8"* to 2" thick doors, L = 3-1/2" (88.8mm)
2" to 2-1/4" thick doors, L = 3-3/4" (95.3mm)
Tailpiece
*Requires addition of Thin Door Kit.
w
T = .098" (2.5mm)
W = .2" (5.2mm)
T
17
P/N AYRD210-INST-FUL REV C
An ASSA ABLOY Group brand
PIN Code Management (With Network Module - Up to 250 Users) - Duplicate Sheet to record entries
User Type
User Name
User #
PIN Code
User
Master
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User Name
User #
PIN Code
19
P/N AYRD210-INST-FUL REV C
An ASSA ABLOY Group brand
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising