Electro-Voice ETX35P Powered Cabinet User manual
advertisement
ETX Powered Loudspeakers
ETX-10P, ETX-12P, ETX-15P, ETX-35P, ETX-15SP, and ETX-18SP
en | User Manual
Table of contents
Tripod and floor monitor operation
Full-Range loudspeaker DSP control menu
Daisy-chaining full-range systems
Using full-range systems as monitors
Stacking full-range systems with subwoofers
Removing the subwoofer caster wheels
en 3
Electro-Voice User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
1
1.1
Safety
Important Safety Instructions
WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT
OVEREXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE
AVIS: RISQUE DE CHOC ELECTRIQUE,
NE PAS OUVRIR.
WARNING: THE MAINS PLUG OR AC
INLET IS USED AS A DISCONNECT
DEVICE. THE DISCONNECT DEVICE
SHALL REMAIN READILY OPERABLE.
WARNING: CONNECT ONLY TO MAINS
SOCKET WITH PROTECTIVE EARTHING
CONNECTION.
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) AS THERE ARE NO
USER-SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
PERSONNEL.
!
The lightening flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
The asterisk within an equilateral triangle is intended to inform the user to necessary installation or removal instructions regarding equipment or hardware use relating to the system.
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with a dry cloth.
7.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
8.
Only use attachments/accessories specified by the manufacturer.
9.
Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on this apparatus.
10. Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
11. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
12. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
13. Unplug the apparatus during lightning storms or when unused for long periods of time.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
1.2
1.3
!
!
en 5
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. To completely disconnect AC power from this apparatus, the power supply cord must be unplugged.
Suspension
Warning!
Suspending any object is potentially dangerous and should only be attempted by individuals who have a thorough knowledge of the techniques and regulations of suspending objects overhead. Electro-Voice strongly recommends all loudspeakers be suspended taking into account all current national, federal, state, and local laws and regulations. It is the responsibility of the installer to ensure all loudspeakers are safely installed in accordance with all such requirements. When loudspeakers are suspended, Electro-Voice strongly recommends the system be inspected at least once per year or as laws and regulations require. If any sign of weakness or damage is detected, remedial action should be taken immediately. The user is responsible for making sure the wall, ceiling, or structure is capable of supporting all objects suspended overhead. Any hardware used to suspend a loudspeaker not associated with Electro-Voice is the responsibility of others.
Warning!
Do not suspend this product in any other manner than explicitly described in this manual, or
Electro-Voice installation guides. Suspending any object (loudspeaker) is potentially dangerous and should only be done by individuals with thorough knowledge of techniques, materials, and regulations for suspending objects overhead. Electro-Voice loudspeakers can only be suspended using accessories and hardware described in Electro-Voice manuals and installation guides. Do NOT use handles to suspend the loudspeaker. Handles on Electro-
Voice loudspeakers are intended to only be used for temporary transport by people. Items, such as fiber rope, wire rope, cables, or other types of materials cannot be used to
suspend loudspeaker from the handles. Any hardware used to suspend a loudspeaker not associated with Electro-Voice is the responsibility of others.
Notices
Old electrical and electronic appliances
Electrical or electronic devices that are no longer serviceable must be collected separately and sent for environmentally compatible recycling (in accordance with the European Waste
Electrical and Electronic Equipment Directive).
To dispose of old electrical or electronic devices, you should use the return and collection systems put in place in the country concerned.
Electro-Voice User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
1.4
1.5
FCC Information
IMPORTANT: Do not modify this unit! Changes or modifications not expressly approved by the manufacturer could void the user’s authority, granted by the FCC, to operate the equipment.
Notice!
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
▪ Reorient or relocate the receiving antenna.
▪ Increase the separation between the equipment and receiver.
▪ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
▪ Consult the dealer or an experienced radio/TV technician.
Precautions
!
If an Electro-Voice loudspeaker is used outdoors on a sunny day, place the loudspeaker in a shaded or covered area. The loudspeaker amplifiers have protection circuits that temporarily shut the loudspeaker off when extremely high temperatures are reached. This can happen on hot days when the loudspeaker is in direct sunlight.
Do not use Electro-Voice loudspeakers in an environment where temperatures are below 0°C (32°F) or exceed +40°C (104°F).
!
Never expose an Electro-Voice loudspeaker to rain, water, or high moisture.
!
!
Electro-Voice loudspeakers are easily capable of generating sound pressure levels sufficient to cause permanent hearing damage to anyone within normal coverage distance. Caution should be taken to avoid prolonged exposure to sound pressure levels exceeding 90 dB.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
2
2.1
en 7
Description
Thank you for choosing an Electro-Voice powered loudspeaker system. Please take time to consult the manual to understand all the features built into your EV system and fully utilize its performance capabilities.
The ETX Powered Loudspeakers are a high-end wood loudspeaker family; consisting of the
ETX-10P, ETX-12P, ETX-15P, ETX-35P, ETX-15SP, and ETX-18SP. Features professional fit and finish, durable, high power systems offers easy portability. The integrated LCD screen allows access to multiple DSP (Digital Signal Processing) settings and system status. ETX Powered
Loudspeakers offer the best-in class sound through design, innovation, amplification, and DSP inspired by EV's legendary engineering team.
Quick setup
The ETX Powered Loudspeakers from Electro-Voice are fully integrated audio systems with carefully matched electronics and transducers. These products make it easy to set up a high quality system quickly with a minimum amount of cables and external electronics.
Full-Range loudspeaker
Models: ETX-10P, ETX-12P, ETX-15P, and ETX-35P
To set up a full-range loudspeaker, do the following:
Illustration Step
1.
Connect the AC power cord from a grounded line receptacle to the MAINS IN.
2.
Connect the XLR or TRS cable from an
audio source to INPUT 1 or INPUT 2.
Electro-Voice
3.
Adjust the input gain to (infinity).
4.
Switch POWER to ON.
5.
From the DSP home screen, increase the
input gain to the desired signal level.
6.
Adjust the MASTER VOL knob to the desired volume.
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
Subwoofer
Models: ETX-15SP and ETX-18SP
To set up a subwoofer, do the following:
Step
1.
Connect the AC power cord from a grounded line receptacle to the MAINS IN.
2.
Connect the XLR or TRS cable from an
audio source to INPUT 1 or INPUT 2.
Illustration
3.
Switch POWER to ON.
2.2
4.
Adjust the MASTER VOL knob to the desired volume.
System features
ETX Powered Loudspeakers from Electro-Voice build upon the legacy and heritage of EV , to deliver the most advanced powered loudspeaker products for portable and permanent applications. The output, response and coverage pattern of EV transducers are all optimized via the breakthrough design approach known as SST (Signal Synchronized Transducers), combined with state-of-the-art on-board DSP which is accessed via an easy-to-use single-knob interface. EV designed and manufactured transducers include SMX woofer technology using composite cone materials, flux stabilizing rings, and thermal management. This transducer yields lower distortion, smooth response and high SPL. The high-efficiency DH3-B compression driver has a convex diaphragm driving a coherent phase device extending frequency response to 20 kHz. The ETX Powered Loudspeaker family features three (3) twoway loudspeakers (10-inch, 12-inch and 15-inch with a 1.5-inch titanium compression driver), a single three-way loudspeaker, and subwoofers with 15-inch and 18-inch drivers. ETX
Powered Loudspeakers combine EV-engineered intelligent DSP, high-powered amplifiers and high-efficiency transducers to deliver that legendary EV sound and performance.
ETX-10P—10-inch two-way powered loudspeaker system
▪ 2000 W amplifier and 134 dB peak SPL
▪ Single-knob DSP includes presets for multiple configurations and top+sub combinations
(performance style, locations, and space)
▪ Loudspeaker system performance monitoring via integrated LCD and front panel LED
▪ SST design assures precise and consistent coverage
▪ Designed for floor, stacked, or tilt pole mount (0 or 7.5 degrees) for portable or permanent installation (Eight (8) M10 threaded suspension points)
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
Electro-Voice en 9
ETX-12P—12-inch two-way powered loudspeaker system
▪ 2000 W amplifier and 135 dB peak SPL
▪ Single-knob DSP includes presets for multiple configurations and top+sub combinations
(performance style, locations, and space)
▪ Loudspeaker system performance monitoring via integrated LCD and front panel LED
▪ SST design assures precise and consistent coverage
▪ Designed for floor, stacked, or tilt pole mount (0 or 7.5 degrees) for portable or permanent installation (Eight (8) M10 threaded suspension points)
ETX-15P—15-inch two-way powered loudspeaker system
▪ 2000 W amplifier and 135 dB peak SPL
▪ Single-knob DSP includes presets for multiple configurations and top+sub combinations
(performance style, locations, and space)
▪ Loudspeaker system performance monitoring via integrated LCD and front panel LED
▪ SST design assures precise and consistent coverage
▪ Designed for floor, stacked, or tilt pole mount (0 or 7.5 degrees) for portable or permanent installation (Eight (8) M10 threaded suspension points)
ETX-35P—15-inch three-way powered loudspeaker system
▪ 2000 W amplifier and 136 dB SPL
▪ Single-knob DSP includes presets for multiple configurations and top+sub combinations
(performance style, locations, and space)
▪ Loudspeaker system performance monitoring via integrated LCD and front panel LED
▪ Features three high-sensitivity transducers, for high output sound which is optimized for precise coverage and low distortion
▪ Designed for floor, stacked, or a combo pole cup (insert and threaded) for portable or permanent installation (Eight (8) M10 threaded suspension points)
ETX-15SP—15-inch powered subwoofer loudspeaker system
▪ 1800 W amplifier and 134 dB peak SPL
▪ Single-knob DSP includes presets for multiple configurations and top+sub combinations
(performance style, locations, and space)
▪ Loudspeaker system performance monitoring via integrated LCD and front panel LED
▪ Includes DSP preset for true cardioid performance
▪ Enclosure includes removable casters and a combo pole cup (insert and threaded) for use with the two-way models
ETX-18SP—18-inch powered subwoofer loudspeaker system
▪ 1800 W amplifier and 135 dB peak
▪ Single-knob DSP includes presets for multiple configurations and top+sub combinations
(performance style, locations, and space)
▪ Loudspeaker system performance monitoring via integrated LCD and front panel LED
▪ Includes DSP preset for true cardioid performance
▪ Enclosure includes removable casters and a combo pole cup (insert and threaded) for use with the two-way models
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
3
3.1
System overview
Technical specifications
ETX-10P, ETX-12P, and ETX-15P
ETX-10P
Frequency Response (-3 dB): 85 Hz – 20 kHz
Frequency Range (-10 dB): 65 Hz – 20 kHz
Maximum SPL: 134 dB peak
Coverage (H x V):
2
1
1
ETX-12P ETX-15P
55 Hz – 20 kHz 1 48 Hz – 20 kHz 1
43 Hz – 20 kHz 1 40 Hz – 20 kHz 1
135 dB peak
90° x 60°
2 135 dB peak 2
Power Rating:
LF Transducer: SMX2100 254 mm
(10 in)
2000 W
SMX2120 300 mm (12 in)
SMX2150 380 mm
(15 in)
HF Transducer:
Crossover Frequency: 1700 Hz
DH3-B 1.25-in titanium compression driver
1600 Hz 1500 Hz
Connectors: (2) XLR/TRS combo jack and (1) XLR link output
Enclosure:
Grille:
18 mm, 13-ply birch plywood with EVCoat
16AWG steel with powdercoat
Suspension: (8) M10 suspension points
Dimensions (H x W x D): 526 mm x 330 mm x 365 mm (21 in x
13 in x 14 in)
613 mm x 381 mm x 400 mm
(24 in x 15 in x
16 in)
691 mm x 431 mm x 447 mm (27 in x
17 in x 18 in)
Net Weight: 20.3 kg (44.8 lb)
Shipping Weight: 22.9 kg (50.5 lb)
23.6 kg (52.0 lb)
26.8 kg (59.1 lb)
27.7 kg (61.1 lb)
31.5 kg (69.5 lb)
Power Consumption: 100 – 240 V~, 50 – 60 Hz, 1.6 – 0.8 A 3
1 Full space measurement using the music DSP preset.
2 Maximum SPL is measured at 1 m using broadband pink noise at maximum output.
3 Current rating is 1/8 power.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
en 11
ETX-35P
ETX-35P
Frequency Response (-3 dB): 48 Hz – 20 kHz 1
Frequency Range (-10 dB): 38 Hz – 20 kHz 1
Maximum SPL: 136 dB peak 2
Coverage (H x V): 60° x 40°
Power Rating: 2000 W
LF Transducer: SMX2151 380 mm (15 in)
MB Transducer: EVS-6C 6.5-in mid-bass driver
HF Transducer: DH3-B 1.25-in titanium compression driver
Crossover Frequency: 700 Hz, 2900 Hz
Connectors: (2) XLR/TRS combo jack and (1) XLR link output
Enclosure: 18 mm, 13-ply birch plywood with EVCoat
Grille: 16AWG steel with powdercoat
Suspension: (8) M10 suspension points
Dimensions (H x W x D): 1023 mm x 469 mm x 426 mm (40 in x 18 in x 17 in)
Net Weight: 38.2 kg (84.2 lb)
Shipping Weight: 42.8 kg (94.4 lb)
Power Consumption: 100 – 240 V~, 50 – 60 Hz, 1.6 – 0.8 A 3
1 Full space measurement using the music DSP preset.
2 Maximum SPL is measured at 1 m using broadband pink noise at maximum output.
3 Current rating is 1/8 power.
Electro-Voice User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
3.2
ETX-15SP and ETX-18SP
ETX-15SP
Frequency Response (-3 dB): 37 Hz – 150 Hz 1
Frequency Range (-10 dB): 32 Hz – 180 Hz 1
Maximum SPL: 134 dB peak 2
ETX-18SP
33 Hz – 150 Hz1 1
28 Hz – 180 Hz 1
135 dB peak 2
Power Rating:
LF Transducer: DVX3159A 380 mm (15 in)
1800 W
DVX3180A 457 mm (18 in)
Low Pass Frequency: Adjustable: 80 Hz, 100 Hz, 120 Hz, 150 Hz
Connectors:
Enclosure:
(2) XLR/TRS Combo Jack and (2) XLR link Output
18 mm, 13-ply birch plywood with EVCoat
Grille: 16AWG steel with powdercoat
Dimensions (H x W x D): 471 mm x 576 mm x 825 mm
(19 in x 23 in x 32 in)
550 mm x 675 mm x 910 mm
(22 in x 27 in x 36 in)
Dimensions (H x W x D): without casters
471 mm x 576 mm x 692 mm
(19 in x 23 in x 27 in)
Net Weight: 41.7 kg (91.9 lb)
550 mm x 675 mm x 777 mm
(22 in x 27 in x 31 in)
51.8 kg (114.2 lb)
Shipping Weight: 46.8 kg (103.2 lb) 58.9 kg (129.9 lb)
Power Consumption: 100 – 240 V~, 50 – 60 Hz, 1.6 – 0.8 A 3
1 Half space measurement using the music DSP preset and 150 Hz low pass.
2 Maximum SPL is measured at 1 m using broadband pink noise at maximum amplifier output.
3 Current rating is 1/8 power.
Dimension drawings
191 mm
[8 in]
330 mm
[13 in]
261 mm
[10 in]
526 mm
[21 in]
236 mm
[9 in]
137 mm
[5 in]
365 mm
[14 in]
40°
166 mm
[7 in]
Right View Left View
Figure 3.1: ETX-10P dimension drawing
Front View
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
en 13
613 mm
[24 in]
Figure 3.2: ETX-12P dimension drawing
691 mm
[27 in]
Figure 3.3: ETX-15P dimension drawing
381 mm
[15 in]
225 mm
[9 in]
431 mm
[17 in]
304 mm
[12 in]
342 mm
[13 in]
166 mm
[7 in]
236 mm
[9 in]
400 mm
[16 in]
40°
224 mm
[9 in]
159 mm
[6 in]
166 mm
[7 in ]
236 mm
[9 in ]
447 mm
[18 in]
40°
Bottom View
161 mm
[6 in]
182 mm
[7 in]
469 mm
[18 in]
508 mm
[20 in]
1023mm
[40 in] 236 mm
[9 in]
Left View
Figure 3.4: ETX-35P dimension drawing
Front View
166 mm
[7 in]
Right View
75°
Bottom View
75°
213 mm
[8 in]
426 mm
[17 in]
Electro-Voice User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
576 mm
[23 in]
471 mm
[19 in]
Left View Front View
Figure 3.5: ETX-15SP dimension drawing
675 mm
[27 in]
550 mm
[22 in]
236 mm
[9 in]
236 mm
[9 in]
333 mm
[13 in]
166 mm
[7 in]
Right View
Figure 3.6: ETX-18SP dimension drawing
3.3
Frequency response graphs
166 mm
[7 in]
368 mm
[14 in]
232 mm
[9 in ]
271mm
[11 in]
Top View
351 mm
[14 in]
692 mm
[27 in]
825 mm
[32 in]
351 mm
[14 in]
777 mm
[31 in]
910 mm
[36 in]
Figure 3.7: ETX-10P frequency response graph: speech, live, and music modes
Figure 3.8: ETX-12P frequency response graph: speech, live, and music modes
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
en 15
Figure 3.9: ETX-15P frequency response graph: speech, live, and music modes
Figure 3.10: ETX-35P frequency response graph: speech, live, and music modes
Figure 3.11: ETX-15SP frequency response graph: live and music modes
Electro-Voice
Figure 3.12: ETX-18SP frequency response graph: live and music modes
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
4
4.1
Operation
Tripod and floor monitor operation
Multi-angle pole cup
The multi-angle pole cup is used to position the ETX-10P, ETX-12P, and ETX-15P loudspeakers for optimal sound coverage. The multi-angle pole cup has two (2) positions 0° and 7.5°. The 0° position points the sound horizontally straight towards the audience. The 7.5° position points the sound at an angle towards the audience and is used when the loudspeaker is above the audience.
0°
7.5°
Figure 4.1: Optimal coverage multi-angle pole cup 0° (left) and multi-angle pole cup 7.5° (right)
Combo pole cup
ETX-35P, ETX-15SP, and ETX-18SP subwoofers use a M20 threaded and 35 mm (1 3/8 in) combination cup to be compatible with both types of poles. M20 threaded poles provide a more secure connection to the subwoofer than the standard 35 mm (1 3/8 in) pole. If using an
M20 threaded pole with the ETX-35P, always place the threads into the subwoofer.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
en 17
Tripod or pole mount
ETX-10P, ETX-12P, and ETX-15P loudspeakers mount on a tripod stand or on a pole above a subwoofer.
Mounting a loudspeaker on a tripod stand
!
!
Figure 4.2: Full-Range models on tripod stand
Caution!
Tripod is not evaluated for safety with this loudspeaker. Check the specifications of the tripod stand to be certain it is capable of supporting the weight of the loudspeaker.
Caution!
Two (2) person lift and placement is recommended for the heavier loudspeakers. Single person lift and placement of heavier loudspeakers could cause injury.
To mount a loudspeaker on a tripod stand, do the following:
1.
Place the tripod stand on a level stable surface.
▪ Fully extend the legs on the tripod stand.
▪ Do not compromise the tripod stands structural integrity by trying to make the stand taller.
▪ Do not attempt to suspend more than one (1) loudspeaker on a stand designed for a single loudspeaker.
2.
Using two (2) hands lift the loudspeaker.
3.
Set the multi-angle pole cup located on the bottom of the loudspeaker onto the pole.
Electro-Voice
Figure 4.3: Multi-angle pole cup 0° (left) and multi-angle pole cup 7.5° (right)
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
Mounting a loudspeaker on a pole
!
Figure 4.4: Full-Range/sub stack with pole mount
Caution!
Two (2) person lift and placement is recommended for the heavier loudspeakers. Single person lift and placement of heavier loudspeakers could cause injury.
To mount a loudspeaker on a pole, do the following:
1.
Place the subwoofer on a level stable surface.
2.
Insert the M20 threaded pole into the combo pole cup on the top of the subwoofer.
Turn the pole clockwise
3.
Turn the M20 threaded pole clockwise to secure the pole to the subwoofer.
4.
Using two (2) hands lift the loudspeaker.
5.
Set the multi-angle pole cup located on the bottom of the loudspeaker onto the pole.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
en 19
Electro-Voice
Figure 4.5: Multi-angle pole cup 0° (left) and multi-angle pole cup 7.5° (right)
Floor monitor
ETX-10P, ETX-12P, and ETX-15P loudspeakers may be used as a floor monitor by placing the speaker on the integral monitor angle.
To set up a loudspeaker as a floor monitor, do the following:
1.
Place the loudspeaker on a level stable surface.
2.
Safely route cables to prevent injury to performers, production crew, and audience members.
Notice!
Secure cables with wire ties or tape whenever possible.
60º
OPTIMAL
COVERAGE
90º
AL
OPTIM
COVERAGE
40º
OR
M
ONIT
ANGLE
Front View
Figure 4.6: Optimum coverage in monitor position
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
4.2
!
Suspension
The ETX-10P, ETX-12P, ETX-15P, and ETX-35P enclosures have eight (8) M10 threaded points; six (6) points on top of the enclosure and two (2) points on the bottom. Forged shoulder eyebolts rated for overhead suspension may be used to suspend an individual loudspeaker, such as the EBK-M10 accessory.
Warning!
Suspending any object is potentially dangerous and should only be attempted by individuals who have a thorough knowledge of the techniques and regulations of suspending objects overhead. Electro-Voice strongly recommends all loudspeakers be suspended taking into account all current national, federal, state, and local laws and regulations. It is the responsibility of the installer to ensure all loudspeakers are safely installed in accordance with all such requirements. When loudspeakers are suspended, Electro-Voice strongly recommends the system be inspected at least once per year or as laws and regulations require. If any sign of weakness or damage is detected, remedial action should be taken immediately. The user is responsible for making sure the wall, ceiling, or structure is capable of supporting all objects suspended overhead. Any hardware used to suspend a loudspeaker not associated with Electro-Voice is the responsibility of others.
Top Suspension
Points
Bottom Suspension
Point
Figure 4.7: Suspension points
Prior to use, inspect the suspension points and associated hardware for any cracks, deformations, broken welds, corrosion, missing or damaged components which could reduce the suspension points strength. Replace any damaged hardware. Never exceed the limitations or maximum recommended load intended for the suspension points. As an added safety measure, it is suggested the user install an extra suspension point back to the building structural supports. This redundant safety point should have as little slack as possible (less than one (1) inch is preferable). Prior to each use, inspect the loudspeaker enclosures for any cracks, deformations, missing or damaged components, which could reduce enclosure strength. Replace any loudspeaker systems damaged or missing hardware.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
Installing the eyebolts
To install the eyebolts, do the following:
1.
Remove the M10 screws from the suspension points.
en 21
2.
Replace the M10 screw with the fender washer and eyebolts.
Electro-Voice
!
Notice!
If the eyebolts are removed reinstall the screws.
If the screws are not reinstalled air leaks occur in the enclosure, resulting in undesirable performance.
Warning!
Eyebolts must be fully seated and oriented in the plane of pull. Always use fender washers at least 1.5 inch in diameter and 1/16 inch thick under the eyebolt to distribute the load on the enclosure.
Washer
Used
No
Washer
Used
Figure 4.8: Eyebolt shown with and without washer
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
!
Correct Incorrect
Figure 4.9: Eyebolts shown oriented in the plane of pull
Warning!
Never exceed the limitations or maximum recommended working load for Electro-Voice loudspeakers.
Disregarding this warning could result in serious injury or death.
5° MAX
5° MAX
5° MAX
50 lb per Suspension Point
5° MAX 30°
90°
!
90°
Figure 4.10: Maximum working load - vertical orientation
Warning!
Never suspend ETX Powered Loudspeakers in a vertical column array.
Disregarding this warning could result in serious injury or death.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
Correct
Figure 4.11: Loudspeaker vertical suspension en 23
Electro-Voice User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
4.3
Amplifier DSP controls
The amplifier has a combination of controls and connectors to ensure the most versatile loudspeaker system.
Full-Range loudspeaker control and monitoring interface
The full-range loudspeaker DSP control menu selections are available for the ETX-10P,
ETX-12P, ETX-15P, and ETX-35P.
Figure 4.12: Full-Range loudspeaker amplifier panel
1.
LCD – DSP control and monitoring interface.
2.
MASTER VOL – Adjusts the sound level.
DSP – Scroll through the menu and select the available choices. Push the MASTER VOL knob to enter the DSP menu.
3.
INPUT LEVEL – Level control for adjusting the individual inputs’ level. The 12 o’clock position is unity gain (no gain or attenuation), the range to the left of zero (0) is for adjusting line level sources, and the range to the right of zero (0) is for adjusting microphone levels. LINE and MIC input level control is available for both INPUT 1 and
INPUT 2.
4.
MIX OUTPUT – XLR output sends the mix of both input signals to another loudspeaker or subwoofer. INPUT LEVEL controls the signal level to MIX OUTPUT. The MASTER VOL or
DSP control settings do not affect MIX OUTPUT.
5.
INPUT – Balanced input for the connection of signal sources like mixing consoles, instruments, or microphones. Connections can be established using ¼ inch TRS or XLR connectors.
6.
POWER – AC switch for switching the power ON or OFF. The LCD screen lights up when the POWER is turned ON.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
en 25
7.
MAINS IN – AC connection is established via an IEC-connector. The IEC-connector is compatible with locking type power cords (not included).
Subwoofer control and monitoring interface
The subwoofer DSP control menu selections are available for the ETX-15SP and ETX-18SP.
Electro-Voice
Figure 4.13: Subwoofer amplifier panel
1.
LCD – DSP control and monitoring interface.
2.
MASTER VOL – Adjusts the sound level.
DSP – Scroll through the menu and select the available choices. Push the MASTER VOL knob to enter the DSP menu.
3.
INPUT – Balanced input for the connection of signal sources like mixing consoles, instruments, or microphones. Connections can be established using ¼ inch TRS or XLR connectors.
4.
OUTPUT – XLR output sends the input signal to another loudspeaker or subwoofer.
INPUT 1 is linked to OUTPUT 1 and INPUT 2 is linked to OUTPUT 2. The MASTER VOL or
DSP control settings do not affect MIX OUTPUT.
5.
POWER – AC switch for switching the power ON or OFF. The LCD screen lights up when the POWER is turned ON.
6.
MAINS IN – AC connection is established via an IEC-connector.
•
See also
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
4.4
System status
Normal system status
Figure 4.14: Normal system status home screen
1.
LOW PASS/HIGH PASS – Displays the high pass or low pass frequency of the system. For full-range models, this indicates the high pass frequency selected. If no subwoofer is used, the display indicates NO SUB. For subwoofer models, this indicates the low pass frequency selected.
2.
MASTER VOL – Indicates the master gain of the system. The range is from mute to +10 dB, in 1 dB increments.
3.
LOCATION – Displays the location setting.
4.
DLY (delay) – Displays the amount of delay.
5.
INPUT 1 METER – Displays the signal level of INPUT 1 in dBu. The meter is post INPUT 1 gain control, but before MASTER VOL control. At signals above +18 dBu, the input indicates CLIP.
6.
INPUT 2 METER – Displays the signal level of INPUT 1 in dBu. The meter is post INPUT 2 gain control, but before MASTER VOL control. At signals above +18 dBu, the input indicates CLIP.
System protection
Figure 4.15: System status limit
1.
PEAK limiter – The peak anticipation limiter protects the loudspeaker from short-term peaks which can cause distortion. Short-term blinking is not critical because the integrated limiter keeps distortion under control. Constant lighting of PEAK indicates the sound is negatively affected. Reducing the output volume (MASTER VOL) is strongly recommended to reduce gain.
2.
TEMP limiter – The temp limiter protects the transducer from thermal failures by reducing the gain. The TEMP LIMITER will flash if any gain reduction is being done.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
en 27
Output reduction
4.5
Figure 4.16: System protect
Under certain circumstances, the amplifier protects itself and reduces the output gain in order prevent shutdown in adverse conditions. This may occur when the mains voltage is very low or high, or when the ambient temperature is very high. The system returns to its original output if the adverse conditions are corrected.
DSP controls
An integrated DSP control menu allows the user to select multiple DSP system settings on the loudspeaker.
Electro-Voice
To access the DSP controls menu, do the following:
1.
Push the MASTER VOL knob.
The DSP Control menu appears.
2.
Using the MASTER VOL knob, scroll through the menu items.
3.
Push the MASTER VOL knob to select the menu item you want to modify.
The focus moves to the menu items on the right side of the DSP menu.
4.
Using the MASTER VOL knob, scroll through the menu items.
5.
Push the MASTER VOL knob to confirm the selected menu items.
The setting is saved. The focus returns to the menu items on the left side of the DSP menu.
6.
Repeat steps 2 through 5 to modify additional DSP and system settings.
7.
Select EXIT to return to the home screen.
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
4.5.1
Full-Range loudspeaker DSP control menu
The full-range loudspeaker DSP control menu selections are available for the ETX-10P,
ETX-12P, ETX-15P, and ETX-35P loudspeakers.
EXIT Menu
The Exit menu is used to return to the home screen.
Notice!
The display returns to the home screen after two (2) minutes of inactivity.
FUNCTION Menu
The Function menu is used to configure the type of sound the loudspeaker delivers. Available options for this selection are: MUSIC, LIVE, and SPEECH.
▪ MUSIC – is used for recorded music playback and EDM applications. (Default)
▪ LIVE – is used for live sound applications.
▪ SPEECH – is used for spoken word applications.
LOCATION Menu
The Location menu is used to optimize the loudspeaker for different boundaries.
ETX-10P, ETX-12P, and ETX-15P: Available options for this selection are: TRIPOD, MONITOR,
WALL, and SUSPEND. ETX-35P: Available options for this selection are: TRIPOD, ARRAY, WALL, and SUSPEND.
▪ TRIPOD – is used when the loudspeaker is placed on a tripod stand or placed on a pole.
(Default)
▪ MONITOR – is used when the loudspeaker is placed on the angled monitor panel in monitor position (Available for the ETX-10P, ETX-12P, and ETX-15P). This setting compensates for the amount of low frequency boost created by placing the speaker close to the floor.
▪ ARRAY – is used when the loudspeaker is part of an array, two (2) boxes side by side using the array bracket kit (Available for the ETX-35P; Array Bracket Kit accessory sold separately). This setting compensates for the effects of placing two (2) loudspeakers in an array.
▪ WALL – is used when the loudspeaker is mounted to the wall using the mounting bracket
(Mounting Bracket accessory sold separately). This setting compensates for the amount of low frequency boost created by placing the loudspeaker close to the wall. If used on a column, it is recommended to use the SUSPEND mode.
▪ SUSPEND – is used when the loudspeaker is suspended in a 3-point suspension by eyebolts.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
Electro-Voice en 29
SUBWOOFER Menu
The Subwoofer menu is used to select a high pass frequency for use with a subwoofer or a matched subwoofer. Available options for this selection are: OFF, 80Hz, 100Hz, 120Hz, 150Hz,
ETX-15SP, and ETX-18SP. The high passes are 24 dB/octave Linkwitz/Riley crossovers. The 80
Hz, 100 Hz, 120 Hz, and 150 Hz choices are generic high pass settings for use with other subwoofers. The ETX-15SP and ETX-18SP settings are specifically optimized for subwoofers by including delay for best summation.
The default is OFF.
ROOM EQ Menu
The Room EQ menu is a 3-band EQ (Equalizer) the user can fine tune beyond the FUNCTION and LOCATION. Available options for this selection are: PEQ1, PEQ2, and PEQ3.
PEQ1,
PEQ2,
PEQ3:
ETX-10P Range: 60 Hz – 20.0 kHz
ETX-12P Range: 50 Hz – 20.0 kHz
ETX-15P Range: 45 Hz – 20.0 kHz
ETX-35P Range: 40 Hz – 20.0 kHz
BACK
Default: 0 dB
Range: -12 dB – +6 dB
Q: 1.2
Notice!
The Room EQ range shown is the factory default range with a stand alone loudspeaker. When a subwoofer is selected, any EQ below the crossover point will be bypassed.
To use the EQ above the crossover point, do the following:
> Rotate the encoder to the desired frequency.
The BYPASS will be removed.
DELAY Menu
The Delay menu is used to create time alignment with other loudspeakers. Available options for this selection are: NONE or a delay up to 343 m. The delay can be changed in 0.25 meter increments. If the unit of measure is feet, available options for this selection are: NONE or a delay up to 1125 ft. The delay can be changed in one (1) foot increments.
The default is NONE.
OPTIONS Menu
The Options menu is used to configure the DSP menu, LCD screen, and system. You can also configure the accessibility of the menu as well as reset the modified settings to factory default.
BACK Menu
The Back menu is used to return to the main menu.
FRONT LIGHT Menu
The Front Light menu shows power on and indicates limit. Available options for this selection are: ON, OFF or LIMIT.
▪ ON – turns the LED on when the power to the loudspeaker is ON. (Default)
▪ OFF – turns the LED off.
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
LIMIT – turns the LED off under normal operation. The LED brief blinking indicates the power amplifier is operated at its limits. Short-term blinking is not critical because the integrated limiter keeps distortion under control. Constant lighting of the LED indicates the sound is negatively affected. Reducing the output volume is strongly recommended.
MEASUREMENT Menu
The Measurement menu is used to select the unit of measure for the delay. Available options for this selection are: METERS or FEET.
The default is METERS.
DISPLAY BRIGHTNESS Menu
The Display Brightness menu is used to determine the brightness of the LCD. The range is 1 to 10.
The default is five (5).
DISPLAY CONTRAST Menu
The Display Contrast menu is used to determine the contrast on the LCD. The range is -10 to
+10.
The default is zero (0).
DIM DISPLAY Menu
The Dim Display menu is used to dim the display when the display is idle for two (2) minutes.
Available options for this selection are: ON or OFF.
The default is ON.
MENU LOCK Menu
The Menu Lock menu is designed to prevent users from inadvertently changing settings.
Available options for this selection are: ON or OFF.
The default is OFF.
To turn menu lock on, do the following:
1.
From the DSP menu, scroll to MENU LOCK.
2.
Select ON.
The Menu lock out message appears.
3.
Select YES.
The menu lock feature is turned on and the LCD displays a lock symbol.
Notice!
If menu lock is ON, the user is allowed to adjust the MASTER VOL.
To unlock the DSP menu, do the following:
> Press and hold the MASTER VOL knob for 5 seconds.
The DSP menu unlocks.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
en 31
RESET FACTORY SETTTINGS Menu
The Reset Factory Settings menu is used to reset the loudspeaker to original factory settings.
Available options for this selection are: NO or YES. The default selection is NO.
To reset the system to original factory settings, do the following:
1.
From the DSP menu, select RESET FACTORY SETTINGS.
The restore factory settings message appears.
4.5.2
Electro-Voice
2.
Select YES.
The loudspeaker restarts and resets the system to the original factory settings.
INFORMATION Menu
The Information menu is used to display the preset version, firmware version, and build date.
•
•
See also
Subwoofer DSP control menu
The subwoofer DSP control menu selections are available for the ETX-15SP and ETX-18SP subwoofers.
EXIT Menu
The Exit menu is used to return to the home screen.
Notice!
The display returns to the home screen after two (2) minutes of inactivity.
FUNCTION Menu
The Function is used to configure the type of sound the subwoofer delivers. Available options for this selection are: MUSIC and LIVE.
▪ MUSIC – is used for recorded music playback and EDM applications. (Default)
▪ LIVE – is used for live sound applications.
LOCATION Menu
The Location menu is used to control output of the subwoofer when used in arrays with other subwoofers.
Available options for this selection are: NORMAL and CARDIOID.
▪ NORMAL – is used for a single subwoofer, or an array of subwoofers where the desired output is effectively omnidirectional. This setting should also be used for the front firing subwoofers in a cardioid array. Under most circumstances, the subwoofer should be set to NORMAL. (Default)
▪ CARDIOID – should ONLY be used on the rear firing subwoofers in cardioid arrays.
To set up cardioid, do the following:
1.
From the DSP menu, scroll to LOCATION.
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
2.
Select CARDIOID.
The CARDIOID (REAR)… message appears.
3.
Select YES.
The location is set to cardioid.
LOW PASS Menu
The Low Pass menu is used to select low pass frequency for proper summation with a full-range loudspeaker. Available options for this selection are: 80 Hz, 100 Hz, 120 Hz, 150 Hz,
ETX-10P, ETX-12P, ETX-15P and ETX-35P. The low passes are 24 dB/octave Linkwitz/Riley slopes. The 80 Hz, 100 Hz, 120 Hz, and 150 Hz selections are generic low pass settings for use with other full-range loudspeaker systems. The ETX-10P, ETX-12P, ETX-15P, and ETX-35P settings are specifically optimized for ETX Powered Loudspeaker by including delay for best summation.
The default is 100 Hz.
ROOM EQ
The Room EQ menu is a single-band EQ the user can fine tune beyond the function and location. Available option for this selection is: PEQ1.
PEQ1: Default: 50 Hz
ETX-15SP Range: 35 Hz to 100 Hz
ETX-18SP Range: 30 Hz to 100 Hz
BACK
Default: 0 dB
Range: -12 dB to +6 dB
Q: 2.0
Notice!
The Room EQ range shown is the factory default settings on a stand alone subwoofer. Room
EQ low frequency range is dependant on the low pass setting selected.
DELAY Menu
The Delay menu is used to create time alignment with other subwoofers. Available options for this selection are: NONE or a delay up to 343 m. The delay can be changed in 0.25 meter increments. If the unit of measure is feet, available options for this selection are: NONE or a delay up to 1125 ft. The delay can be changed in one (1) foot increments.
The default is NONE.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
Electro-Voice en 33
POLARITY Menu
The Polarity menu is used to change the polarity of the subwoofer system. Available options for this selection are: NORMAL and REVERSE.
▪ NORMAL – A positive signal into the subwoofer produces a positive sound pressure.
(Default)
▪ REVERSE – A positive signal into the subwoofer produces a negative sound pressure.
Notice!
If one (1) subwoofer is set to NORMAL and another subwoofer is set to REVERSE, the output of the subwoofers cancels acoustically.
Ensure all subwoofers in a system are set to the same polarity of the output so the subwoofers sum properly. Under most circumstances, the polarity of the subwoofer should be set to NORMAL.
OPTIONS Menu
The Options menu is used to configure the DSP menu, LCD screen, and system. You can also configure the accessibility of the menu as well as reset the modified settings to factory default.
BACK Menu
The Back menu is used to return to the main menu.
FRONT LIGHT Menu
The Front Light menu shows power on and indicates limit. Available options for this selection are: ON, OFF or LIMIT.
▪ ON – turns the LED on when the power to the loudspeaker is ON. (Default)
▪ OFF – turns the LED off.
LIMIT – turns the LED off under normal operation. The LED brief blinking indicates the power amplifier is operated at its limits. Short-term blinking is not critical because the integrated limiter keeps distortion under control. Constant lighting of the LED indicates the sound is negatively affected. Reducing the output volume is strongly recommended.
MEASUREMENT Menu
The Measurement menu is used to select the unit of measure for the delay. Available options for this selection are: METERS or FEET.
The default is METERS.
DISPLAY BRIGHTNESS Menu
The Display Brightness menu is used to determine the brightness of the LCD. The range is 1 to 10.
The default is five (5).
DISPLAY CONTRAST Menu
The Display Contrast menu is used to determine the contrast on the LCD. The range is -10 to
+10.
The default is zero (0).
DIM DISPLAY Menu
The Dim Display menu is used to dim the display when the display is idle for two (2) minutes.
Available options for this selection are: ON or OFF.
The default is ON.
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
MENU LOCK Menu
The Menu Lock menu is designed to prevent users from inadvertently changing settings.
Available options for this selection are: ON or OFF.
The default is OFF.
To turn menu lock on, do the following:
1.
From the DSP menu, scroll to MENU LOCK.
2.
Select ON.
The Menu lock out message appears.
3.
Select YES.
The menu lock feature is turned on and the LCD displays a lock symbol.
Notice!
If menu lock is ON, the user is allowed to adjust the MASTER VOL.
To unlock the DSP menu, do the following:
> Press and hold the MASTER VOL knob for 5 seconds.
The DSP menu unlocks.
RESET FACTORY SETTTINGS Menu
The Reset Factory Settings menu is used to reset the loudspeaker to original factory settings.
Available options for this selection are: NO or YES. The default selection is NO.
To reset the system to original factory settings, do the following:
1.
From the DSP menu, select RESET FACTORY SETTINGS.
The restore factory settings message appears.
2.
Select YES.
The loudspeaker restarts and resets the system to the original factory settings.
INFORMATION Menu
The Information menu is used to display the preset version, firmware version, and build date.
•
•
See also
Subwoofer cardioid array, page 38
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
4.6
4.6.1
Recommended configurations
Daisy-chaining full-range systems
Vocal
Microphone
en 35
Electro-Voice
Notice!
The direction of the arrow indicates the signal path.
Location:
Function:
Subwoofer:
Table 4.1: DSP settings loudspeaker on a tripod
Tripod
Speech
Off
•
See also
Full-Range loudspeaker DSP control menu, page 28
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
4.6.2
Using full-range systems as monitors
Vocal
Microphone
Instrument
Notice!
The direction of the arrow indicates the signal path.
Location:
Function:
Subwoofer:
Table 4.2: DSP settings loudspeaker as a monitor
Monitor
Live
Off
•
See also
Full-Range loudspeaker DSP control menu, page 28
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
4.6.3
Stacking full-range systems with subwoofers
ETX-12P
ETX -18 SP en 37
Electro-Voice
Mixer
Notice!
The direction of the arrow indicates the signal path.
Location:
Function:
Subwoofer:
ETX-12P
Tripod
Live
ETX-18SP
Location:
Function:
ETX-18SP
Normal
Live
High Pass: ETX-12P
Table 4.3: DSP settings loudspeaker and subwoofer stacked
•
•
See also
Full-Range loudspeaker DSP control menu, page 28
Subwoofer DSP control menu, page 31
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
4.6.4
Subwoofer cardioid array
Subwoofer cardioid array
The ETX-15SP and ETX-18SP subwoofers have cardioid array processing originally developed for Electro-Voice concert subwoofer systems. Cardioid subwoofer arrays can be used to direct the output of an array of subwoofers in order to limit excessive amounts of bass in undesired areas. These arrays can be used to keep bass off of a stage, provides more consistent bass coverage in the audience, and reduces bass in the surrounding area.
Multiple ETX-15SP or ETX-18SP can be arrayed to create a cardioid polar pattern. See
Cardioid pattern top view. The cardioid setting in the DSP menu is optimized to produce a rear rejection of up to 30 dB without any additional processing. The rejection may be less in smaller indoor environments than in larger outdoor environments. For best performance, adhere to the following guidelines:
▪ The subwoofers must all be the same model, for example all ETX-15SP or all ETX-18SP.
▪ The subwoofers must be physically placed in one (1) of the options shown. See Cardioid physical alignment.
▪ Front firing subwoofers use the NORMAL location setting, and rear firing subwoofers use the CARDIOID setting. All other settings should be the same between front and rear firing subwoofers.
▪ To add delay to the cardioid array, add the same amount to both the front and rear facing subwoofers.
Figure 4.17: Cardioid pattern top view
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
en 39
Rejection
Electro-Voice
A
B
Audience
C
Figure 4.18: Cardioid physical alignment
Cardioid option A:
Either two (2) ETX-15SP or two (2) ETX-18SP subwoofers orientated vertically. Direct the top subwoofer towards the audience and the bottom subwoofer away from the audience
(Rejection direction).
Cardioid option B:
Either three (3) ETX-15SP or three (3) ETX-18SP subwoofers orientated vertically. Direct the top two (2) subwoofers towards the audience and the bottom subwoofer away from the audience (Rejection direction).
Cardioid option C:
Either three (3) ETX-15SP or three (3) ETX-18SP subwoofers orientated horizontally. Direct the left and right subwoofers towards the audience and the center subwoofer away from the audience (Rejection direction).
Location:
Polarity:
Delay:
Subwoofers facing the audience
Normal
Normal
0 m (zero)
Subwoofers facing away from the audience (Rejection direction)
Location:
Polarity:
Delay:
Table 4.4: Subwoofer cardioid
Cardioid
Normal
0 m (zero)
For more information about cardioid arrays, see ETX-15SP or ETX-18SP product pages on www.electrovoice.com.
•
See also
Subwoofer DSP control menu, page 31
User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
4.7
Removing the subwoofer caster wheels
The ETX-15SP and ETX-18SP subwoofers have caster wheels attached for easy transportation in portable applications. The caster wheels are removable for a permanent installation.
To remove the subwoofer caster wheels, do the following:
1.
Remove the 16 M6 screws, 16 washers, and four (4) casters on the rear of the subwoofer.
2.
Install the 16 M6 screws and 16 washers back into the rear of the subwoofer.
Ensure all 16 M6 screws are tight.
Notice!
If the caster wheels are removed reinstall the screws.
If the screws are not reinstalled air leaks occur in the enclosure, resulting in undesirable performance.
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
en 41
5 Troubleshooting
Problem
1.
No Sound
Possible Cause(s)
Amplifier
Wiring
Action
Connect a known working test loudspeaker to the amplifier outputs. If there is no sound, verify all the electronics are on, the signal routing is correct, the source is active; the volume is turned up, etc. Correct/repair/replace as necessary. If there is sound, the problem is wiring.
Verify you have connected the correct cables to the amplifier. Play something at a low level through the amplifier. Connect the test loudspeaker in parallel with the malfunctioning line. If the sound level is gone or is very weak, the line has a short in it (possibly a severe scrape, pinch, or a missed connection). Using the test loudspeaker, move down the line and test each connection/junction until you find the problem and correct it. Observe proper polarity.
If no subwoofers are used with the system, select the OFF position.
2.
Poor
Low-
Frequency
Response
With SUB menucross-over frequency activated
3.
Intermittent output such as cracking or distortion
4.
Constant noise such as buzzing, hissing or humming
Faulty Connection
Defective source or other electronic device
Poor system grounding or ground loop
Check all connections at amplifier and loudspeakers to ensure they are all clean and tight. If the problem persists, check the wiring. See problem 1.
If noise is present, but no program material is playing, evaluate each component as necessary to isolate the problem. Most likely there is a break in the signal path.
Check and correct the system grounding, as required.
Input gain knob is not in the MIC position
5.
No sound produced with microphone connected to
INPUT 1 or
INPUT 2
Microphone requires phantom power
Input gain knob is not in the MIC position
Slowly increase the input gain knob level to engage the microphone pre-amp.
Use a dynamic microphone that does not require phantom power. If using a microphone requiring phantom power, an external phantom power source is needed.
Slowly increase the input gain knob level to engage the microphone pre-amp.
6.
Sound is distorted front
LED is OFF,
LCD screen
LIMIT is ON
Excessive input level Reduce the input level or loudspeaker level knobs to prevent limit.
Electro-Voice User Manual 2016.04 | 05 | F.01U.276.083
ETX Powered Loudspeakers
Problem Possible Cause(s)
Incorrect gain structure or source input (mixing console/preamp) is overdriven
Incorrect gain structure
Action
Verify level controls of the source are properly structured by using the VU meter indicator on the LCD screen. If the
VU meter bar is solid or the system indicates LIMIT, the input or source level is too high.
7.
Microphone produces acoustic feedback when input level is amplified
Reduce the microphone levels at the mixing console or input source. If the microphone is connected directly to the speaker, reduce the input level on the speaker. Positioning the microphone close to the sound source increases gainbefore-feedback. See problem 6.
FUNCTION is set to
MUSIC
Microphone position is too close to the front of the loudspeaker
Change the LOCATION to LIVE or SPEECH.
Whenever possible setup the loudspeakers so the microphone is behind them. If using the loudspeaker in a monitor position, aim the loudspeaker to the back of the microphone.
Press and hold the MASTER VOL knob for 5 seconds.
8.
DSP menu is locked.
The Menu Lock function has been turned on. A lock symbol displays on the LCD screen.
If these suggestions do not solve your problem, contact your nearest Electro-Voice dealer or Electro-
Voice distributor.
•
•
•
See also
Full-Range loudspeaker DSP control menu, page 28
Full-Range loudspeaker DSP control menu, page 30
2016.04 | 05 | F.01U.276.083
User Manual Electro-Voice
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2016
Bosch Security Systems, Inc
12000 Portland Avenue South
Burnsville MN 55337
USA www.electrovoice.com
advertisement