Keysight N5416A and N5417A USB Compliance Test

Keysight N5416A and N5417A USB Compliance Test
Keysight N5416A and N5417A
USB Compliance Test Software for Infiniium
Oscilloscopes
Data Sheet
02 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Easily Verify USB Electrical Parameters
The N5416A USB compliance test
software for Infiniium oscilloscopes gives
you a fast and reliable way to verify USB
electrical specification compliance for
your USB 2.0 devices, hosts and hubs.
The software executes the official USB-IF
MATLAB scripts with MATLAB’s runtime
engine embedded in the oscilloscope.
–– Easy-to-use interface for fast setup,
configuration and automated test
–– Recognized by the USB-IF for USB
compliance testing
–– Additional features: support for USB
OTG (on-the-go) and multi-trial
testing
–– USB-IF MATLAB script execution
inside the Infiniium oscilloscope
–– Award-winning Infiniium ease of use
–– Test fixtures for USB 1.1 (low- and
full-speed), USB 2.0 (high-speed) and
USB OTG compliance
With USB compliance test software, you
can take the Infiniium oscilloscope you use
for everyday debugging and use it to verify
USB electrical parameters with the same
testing scripts the USB-IF created for
official compliance testing at designated
workshops. The USB compliance test
software has a new setup wizard that
allows you to quickly and easily test all
facets of electrical compliance of your
device, host or hub. The setup wizard
menu structure of the N5416A USB test
option provides a level of simplicity not
found with other vendors multi-tiered
menu structures for executing tests and
documenting results.
Figure 1. The Infiniium USB compliance tests are incorporated directly into the oscilloscopeís menu
structure as a submenu under the Analyze menu.
Figure 2. You can configure and launch the Infiniium USB compliance tests through a single
window.
03 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Easily Verify USB Electrical Parameters (Continued)
Low-, full- and high-speed tests require
compliance with signal quality, inrush
current, droop, drop, and backdrive
voltage tests. Hi-speed USB requires
compliance with an additional suite of
tests. These tests are provided by the
USB compliance test software, along with
USB OTG (on-the-go) test capability (with
the automated USB OTG electrical test
fixture). Tests can be executed directly
from the scope interface under the
Analyze menu.
Figure 3. You can select individual tests or the entire list of compliance tests from a single window
page.
04 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Benefits
In the past, pre-compliance testing in a
lab environment involved capturing data
with an oscilloscope, transferring it to a
PC and post-processing it with a software
program. Keysight Technologies, Inc.
has simplified the process by installing a
run-time version of MATLAB software in
the scope and integrating the USB test
option into the Infiniium oscilloscope’s
menu structure.
Once the test is executed, the test results
appear on the Infiniium display in an
HTML-formatted window.
Figure 4. Test instructions and diagrams are included to help you configure your equipment.
Figure 5. Infiniium scopes automatically display test results in an html window immediately after
test execution.
05 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Benefits (Continued)
Each test also automatically saves the
PNG, HTML, and TSV files required
by the USB-IF. The higher data rates
associated with hi-speed USB 2.0
demand a measurement system that
will not interfere with your device/host/
hub operation by loading the system.
The award-winning InfiniiMax probing
system, which is compatible with Infiniium
oscilloscopes, provides unmatched signal
fidelity – ensuring your measurement
system does not load the signals under
test – so it does not compromise the
specification margins for passing the
electrical signal quality tests. The
InfiniiMax probing system has been
approved by the USB-IF for compliance
testing. The set of six high-speed test
fixtures are highly manageable in a test
environment due to their small size. The
six fixtures allow you the flexibility to run
different tests concurrently when you
have more than one host, hub, or device
to verify for compliance. The OTG fixture
available is the only automated OTG test
fixture for USB OTG compliance testing.
Figure 6. The results are stored in a printable HTML report.
Figure 7. USB OTG test instructions.
06 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Extensibility
You may add additional custom tests
or steps to your application using the
N5467A User-Defined Application (UDA)
development tool (www.keysight.com/
find/uda). Use UDA to develop functional
“Add-Ins” that you can plug into your
application.
Add-ins may be designed as:
–– Complete custom tests (with
configuration variables and
connection prompts)
–– Any custom steps such as pre or
post processing scripts, external
instrument control and your own
device control
Figure 8. Importing a UDA Add-In into your test application.
Figure 9. UDA Add-In tests and utilities in your test application.
07 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Automation
You can completely automate execution of
your application’s tests and Add-Ins from
a separate PC using the included N5452A
Remote Interface feature (download free
toolkit from www.keysight.com/find/
scope-apps-sw). You can even create and
execute automation scripts right inside
the application using a convenient built-in
client.
The commands required for each task may
be created using a command wizard or
from “remote hints” accessible throughout
the user interface. Using automation, you
can accelerate complex testing scenarios
and even automate manual tasks such as:
–– Opening projects, executing tests and
saving results
–– Executing tests repeatedly while
changing configurations
–– Sending commands to external
instruments
–– Executing tests out of order
Combine the power of built-in automation
and extensibility to transform your
application into a complete test suite
executive:
–– Interact with your device controller
to place it into desired states or test
modes before test execution.
–– Configure additional instruments used
in your test suite such as a pattern
generator and probe switch matrix.
–– Export data generated by your tests
and post-process it using your favorite
environment, such as MATLAB,
Python, LabVIEW, C, C++, Visual Basic
etc.
–– Sequence or repeat the tests and
“Add-In” custom steps execution in
any order for complete test coverage
of the test plan.
Figure 10. Remote programming script in the Automation tab.
Compliance app + Automation engine
UDA add-in
- Custom test/Steps
- Post processing
C++ Script
LabVIEW
UDA add-in
- DUT control
- Instrument control
Pattern
generator
Custom tests
Matlab processing
Results
DUT or external
instrument control
Switch
matrix
Live signals
DUT
Custom tests/Steps
or post processing
Figure 11. Combine the power of built-in automation and extensibility to transform your application
into a complete test suite executive.
08 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Recommended Test Equipment
The N5416A USB test option requires
an Infiniium 4-channel or 4+16 channel
oscilloscope. To run hi-speed USB
compliance tests, you will need E2649A/
E2649B fixtures. For low/full-speed tests,
you will need a E2646B SQuIDD test
fixture. For USB OTG tests, in addition to
the Infiniium oscilloscope, you will need
an N5417A USB OTG test fixture and an
E3631A power supply and 34401A digital
multimeter.
No fixtures are supplied with the N5416A
software. One SQuIDD test fixture must
be ordered separately as part number
E2646B (for low- and full-speed testing).
A set of six high-speed test fixtures for
signal quality, receiver sensitivity, TDR,
and host disconnect must be ordered
separately as part number E2649B.
For USB OTG (on-the-go) test, USB
OTG electrical fixture must be ordered
separately as part number N5417A.
Figure 12. USB OTG test selections.
Figure 13. E2649B test fixture.
09 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Recommended Test Equipment (Continued)
Recommended high-speed test equipment 1
Infiniium Series oscilloscope (recommended bandwidth: 2 GHz or higher)
Model or part number
N5416A
E2649B
1131A/32A/34A
N5442A
E2678A
Digital signal generator 3
82357B 4
TDR4
34401A
Hi-speed USB
Test bed computer
USB cable
USB-IF tool on host system
Description
USB 2.0 low-/full-/high-speed test option for Infiniium oscilloscopes 2
Hi-speed USB 2.0 test fixture set consists of:
–– E2649-66401 device TDR/signal quality test fixture
–– E2649-66402 host TDR/signal quality test fixture
–– E2649-66403 device receiver sensitivity fixture
–– E2649-66404 host disconnect test fixture
–– E2649-66405 droop and drop test fixture
InfiniiMax probe amplifier (qty 2 required for hub testing)
InfiniiMax III 3.5 mm to precision BNC adapter (required for the 90000 X-Series)
Differential socketed probe head for InfiniiMax probe amplifiers (qty 2 required for hub testing)
81130A pulse data generator with options:
–– 11-MB SRAM memory card (UFJ)
–– 81132A 660-MHz option
–– 8493C 006 6-dB attenuator
–– Male SMA cable
Or
81134A pulse generator:
–– 15433B 500 ps transition time converter (for use with the 81134A)
–– Male SMA cable
USB-to-GPIB interface converter
86100A/B/C
54754A
Male SMA cable
Digital multimeter
Hardware configuration: 815EEA2 motherboard, Pentium III 700 MHz
256 MB RAM, 40-GB HD, CD (CD-RW), FD, IOGear (or ATEN) USB 2.0 PCI card (5-port)
Software configuration: Windows XP
1.5-meter cable 6
1-meter cable
HS electrical test tool available from www.usb.org (USBHSET.exe)
Quantity
1
1
1
3
1
1
2
2
2
2
2
1
1
2
1
1
1
1
1
1. High-speed devices must support the full-speed mode. Consult the “Recommended low/full-speed test equipment” table for the required test equipment.
2. Option 8, enhanced bandwidth, is recommended for the 54855A. Option 5, noise reduction, is recommend for the 80000, 90000 and 90000 X-Series
oscilloscopes.
3. A digital signal generator is required when testing receiver sensitivity for devices/hubs.
4. 82357A (USB1.1) is obsolete and replaced by 82357B (USB 2.0).
5. The TDR test was deleted from the Hi-speed Test Procedure (Rev. 1.0), but it is still recommended during development.
6. Not available from Keysight. Refer to www.usb.org for lists of qualified vendors.
(Note that four damped adapters are included with the E2649A)
(The damped adapter part number is 01130-63201)
10 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Recommended Test Equipment (Continued)
Recommended low-/full-speed test equipment 1
With Keysight Infiniium Series or 54830B/D, 54832A/D oscilloscopes.
Model or part number
N5416A
E2646B
1165A
N2873A
E2697A
10075A
8710-2063
1147B
N2782A and N2779A 2
USB host system
USB cable
USB-IF tool on
Description
USB 2.0 low-/full-/high-speed test option for Infiniium oscilloscopes
One SQuIDD (signal quality inrush, drop/droop) test fixture for low-/full-speed USB 2.0 testing
Miniature passive probe for the 5483x Series oscilloscopes
Passive probe for the 9000 Series oscilloscopes
High-impedance adapter with one 10073C passive probe (for the 90000A Series oscilloscopes)
Clip adapter (for each E2697A)
Dual lead adapters
50-MHz current probe (for 8000, 54831B/D or 32B/D only)
50-MHz 30 A current probe and 3-channel power supply
Refer to http://compliance.usb.org/Interoperability
5-meter cable
1-meter cable
HS electrical test tool available from www.usb.org (USBHSET.exe)
Quantity
1
1
3
3
3
3
3
1
1
1
6
1
1
1. High-speed devices must support the full-speed mode. Consult the “Recommended low/full-speed test equipment” table for the required test equipment.
2. N2774A and N2775A are obsolete and replaced with N2779A and N2782A.
USB OTG recommended test equipment
Using Keysight Infiniium Series or 54830B/D, 54832A/D.
Model or part number
N5417A
N2873A
E2697A
E3631
34401
82357B 3
10833A
Description
USB OTG (on-the-go) electrical test fixture
Passive probe for the 9000 Series oscilloscopes
High-impedance adapter with one 10073C passive probe (for the 90000A Series oscilloscopes)
Power supply unit
Digital multimeter (DMM)
USB/GPIB interface cable
GPIB cable
3. 82357A is obsolete and replaced by 82357B.
Quantity
1
2
2
1
1
1
1
11 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Infiniium Series USB 2.0 Compliance Test Application Capabilities
The following table summarizes the features of Keysight’s various USB test analysis options in InfiniiVision 6000 X-Series and Infiniium
oscilloscopes:
Table 1. USB Testing coverage comparison
USB measurement
EL_2 EL_4 EL_5 Data Eye and Mask Test High speed
SQ
Consecutive, paired JK, and paired KJ jitter
Full and Low speed signal quality
Sync test
Cross-over voltage (low- and full-speed only)
EOP bit-width
Signaling rate
EL_6 Device Rise and Fall Time
Edge rate match (low- and full-speed only)
HTML pass/fail report generation
EL_7 Device Non-Monotonic Edge Test
EL_22 Interpacket Gap Tests
EL_28 Chirp-K Latency
EL_29 Device CHIRP-K Duration
EL_31 Host Hi-Speed Terminations Enable and D+
Disconnect Time
EL_38 EL_39 Device Suspend Timing Response
EL_40 Device Resume Timing Response
EL_27 Device CHIRP Response to Reset from
Hi-Speed Operation
EL_28 Device CHIRP Response to Reset from
Suspend
EL_8 Device J Test
EL_8 Device K Test
EL_9 Device SE0_NAK Test
Inrush Current Test
Drop/Droop Vbus tests
VBus Backdrive tests
Signal integrity testing with InfiniiVision
4000/6000X with the USBSQ option
√
Complete USB-IF electrical compliance
testing with Infiniium S-Series N5416A option
√
√
√
√
√
√
√
√1
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
1. To accurately measure USB 2.0 rise and fall times with less than 10% error for sub 500 ps edges the measurement BW must be at least 2.5 GHz as required
for official USB-IF compliance testing.
12 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Ordering Information
Infiniium oscilloscope
90000A Series
9000 Series
9000 H-Series
90000 X-Series
Operating system
Windows 7
Windows XP Pro
Software revision
02.10 or higher
02.00 or higher
04.20 or higher
03.00 or higher
USB test option
N5416A or opt. 29 on new scope purchases
N5416A or opt. 29 on new scope purchases
N5416A or opt. 29 on new scope purchases
N5416A or opt. 29 on new scope purchases
Tests
Low-/full-/high-speed
Low-/full-/high-speed
Low-/full-/high-speed
Low-/full-/high-speed
Note that free upgrade media for Infiniium oscilloscopes is available for order online at
http://www.keysight.com/find/infiniium_software.
Keysight Oscilloscopes
Multiple form factors from 20 MHz to > 90 GHz | Industry leading specs | Powerful applications
13 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
www.axiestandard.org
AdvancedTCA® Extensions for Instrumentation and Test (AXIe) is an
open standard that extends the AdvancedTCA for general purpose and
semiconductor test. The business that became Keysight was a founding
member of the AXIe consortium. ATCA®, AdvancedTCA®, and the ATCA logo
are registered US trademarks of the PCI Industrial Computer Manufacturers
Group.
www.lxistandard.org
LAN eXtensions for Instruments puts the power of Ethernet and the Web
inside your test systems. The business that became Keysight was a founding
member of the LXI consortium.
www.pxisa.org
PCI eXtensions for Instrumentation (PXI) modular instrumentation delivers a
rugged, PC-based high-performance measurement and automation system.
14 | Keysight | N5416A and N5417A USB Compliance Test Software for Infiniium Oscilloscopes - Data Sheet
Evolving
Our unique combination of hardware, software, support, and people can help
you reach your next breakthrough. We are unlocking the future of technology.
From Hewlett-Packard to Agilent to Keysight
myKeysight
www.keysight.com/find/mykeysight
A personalized view into the information most relevant to you.
Keysight Infoline
www.keysight.com/find/Infoline
Keysight’s insight to best in class information management. Free access to
your Keysight equipment company reports and e-library.
KEYSIGHT
SERVICES
Keysight Services
www.keysight.com/find/service
Our deep offering in design, test, and measurement services deploys an
industry-leading array of people, processes, and tools. The result? We help
you implement new technologies and engineer improved processes that
lower costs.
Three-Year Warranty
www.keysight.com/find/ThreeYearWarranty
Keysight’s committed to superior product quality and lower total cost
of ownership. Keysight is the only test and measurement company with
three-year warranty standard on all instruments, worldwide. And, we provide
a one-year warranty on many accessories, calibration devices, systems and
custom products.
Keysight Assurance Plans
www.keysight.com/find/AssurancePlans
Up to ten years of protection and no budgetary surprises to ensure your
instruments are operating to specification, so you can rely on accurate
measurements.
Keysight Channel Partners
www.keysight.com/find/channelpartners
Get the best of both worlds: Keysight’s measurement expertise and product
breadth, combined with channel partner convenience.
For more information on Keysight
Technologies’ products, applications or
services, please contact your local Keysight
office. The complete list is available at:
www.keysight.com/find/contactus
Americas
Canada
Brazil
Mexico
United States
(877) 894 4414
55 11 3351 7010
001 800 254 2440
(800) 829 4444
Asia Pacific
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Other AP Countries
1 800 629 485
800 810 0189
800 938 693
1 800 11 2626
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
(65) 6375 8100
Europe & Middle East
Austria
Belgium
Finland
France
Germany
Ireland
Israel
Italy
Luxembourg
Netherlands
Russia
Spain
Sweden
Switzerland
United Kingdom
0800 001122
0800 58580
0800 523252
0805 980333
0800 6270999
1800 832700
1 809 343051
800 599100
+32 800 58580
0800 0233200
8800 5009286
800 000154
0200 882255
0800 805353
Opt. 1 (DE)
Opt. 2 (FR)
Opt. 3 (IT)
0800 0260637
For other unlisted countries:
www.keysight.com/find/contactus
(BP-06-08-16)
DEKRA Certified
ISO9001 Quality Management System
www.keysight.com/go/quality
Keysight Technologies, Inc.
DEKRA Certified ISO 9001:2015
Quality Management System
This information is subject to change without notice.
© Keysight Technologies, 2011 - 2016
Published in USA, June 9, 2016
5989-4044EN
www.keysight.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising