Instruction Manual Gigabit Ethernet Fiber Media Converter Card

Instruction Manual Gigabit Ethernet Fiber Media Converter Card
Instruction Manual
Gigabit Ethernet Fiber Media Converter Card Module with Open SFP Slot
ET91000SFP2 / ET91000SFP2C
Front
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
Dip Switch
Packaging Contents
ET91000SFP2
LED Indicators
RJ45 Ethernet Connector
ET91000SFP2C
• 1 x Fiber Media Converter
• 1
x Fiber Media Converter
• 1 x Universal Power Adapter (NA/EU/UK) • Instruction Manual
• Instruction Manual
Thumb Screw
Release
SFP Slot
Rear
DC Power Connector
System Requirements
•
•
•
•
MSA Compliant Gigabit SFP Module
1000BASE-T compatible Ethernet network equipment
RJ45 terminated UTP Cat5e or better Ethernet cable
Available AC electrical outlet
Ground Point(Optional)
Installation
Installation into ETCHS2U Chassis
1. Make sure the DIP switches are set appropriately for
your network configuration (see “DIP Switch Settings“
section for details).
2. Insert a compatible SFP module into the open SFP slot.
3. Connect a fiber optic network cable from a computer /
switch / media converter to the inserted SFP connector
on the media converter.
The ETCHS2U chassis supports the full line of StarTech.com ET series
2 media converters, which can be installed in a mixed fashion to suit
your environment. The cards are designed to be hot-swappable,
meaning the chassis need not be powered off in order to remove or
insert a card.
1. If the chassis slot was previously unused, loosen the screw at the
top of the slot to remove the cover plate
2. Align the card with the desired slot of the chassis and gently slide
the card into the groove to seat the power connection
3. Re-tighten the captive screw to hold the card in place
NOTE: When connecting the fiber cable to your installed SFP
module, make sure to connect the Tx (transmit) terminal on one end,
with the Rx (receive) terminal on the other end.
4. Connect a UTP Ethernet cable from a computer/switch
to the RJ45 jack on the media converter.
5. Connect the power adapter to the media converter.
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 09/10/2013
The following example illustrates the connection scheme when connecting from a
1000BASE-T Ethernet port of a hub/switch to a 1000BASE-SX/LX port of another hub/switch,
through the fiber media converter:
The following example illustrates the connection scheme when connecting from a
1000BASE-T Ethernet port on a hub/switch to a 1000BASE-T Ethernet Network Interface
Card (NIC) in a computer through the fiber media converter:
DIP Switch Settings
DIP Switch Settings
LED
PWR
(Green)
Supported Standards
IEEE 802.3ab, IEEE 802.3z
Connectors
1 x RJ45 Ethernet female
1 x SFP Slot
1 x DE-15 VGA male
2 x DE-15 VGA female
1 x 5V DC Power
1 x DC Power
1 x Power
1 x Input Signal Detect
Max Data Rate
1.25 Gbps
Compatible Fiber Type
Depends on SFP
Optical Wavelength
Depends on SFP
Maximum Distance
Depends on SFP (Fiber), 100m (RJ45)
Duplex Modes
Full/Half
Auto MDIX
Yes (Ethernet)
Power
12V DC, 1 A, Center-positive, Type M plug
Power Consumption
< 8W
Status
On
Power on
Flash
During upgrade (rapid flash)
Off
No Power or Card Disabled
Remote Power Failure
Enclosure Material
Metal
Operating Temperature
0°C to 60°C (32°F to 140°F)
Storage Temperature
-10°C to 70°C (14°F to 158°F)
Humidity
10~90% RH (Non-Condensing)
Dimensions (LxWxH)
160 x 95 x 20mm
Weight
400g
(Green)
On
Off
Remote Power Normal
LFP
(Green)
On
Link Fault Pass-thru Enabled
Off
Link Fault Pass-thru Disabled
On
Fiber Link is OK
Off
No Fiber Link
UTP is Full Duplex
(Green)
ET91000SFP2/ ET91000SFPC
State
RPF
LNK
Specifications
FULL
(RJ45)
(Green)
On
Off
UTP is not Full Duplex
LINK
(RJ45)
(Green)
On
UTP link is OK
Off
No UTP link
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access
our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned
for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,
consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow
the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising