DG-PE2248D QIG - Smartlink Network Systems Ltd

DG-PE2248D QIG - Smartlink Network Systems Ltd
DG-PE2248D Quick Installation Guide
DG-PE2248D Quick Installation Guide
DG-PE2248D Quick Installation Guide
Safety
Min. System Requirements
This equipment is designed with the utmost care for the safety of
those who install and use it. However, special attention must be
paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the
computer manufacturer must therefore be allowed at all times to
ensure the safe use of the equipment.
• Minimum Cat 5 Ethernet cable
• An AC power source for Powering ON the device
Package Contents
Side View – Power Connector
Following figure shows the side view of the product. There is a
power connector to connect the power cord from the AC power
source.
The following items should be present in your package:
1. DG-PE2248D Desktop Mount 48V DC Giga PoE Injector
2. Quick Installation Guide
3. Power Cord
DG-PE2248D
Desktop Mount 48V DC Giga PoE Injector
Quick Installation Guide
V1.0
2015-08-26
As our products undergo continuous development the specifications are subject to change without
prior notice
Copyright
Copyright 2015 by Smartlink Network Systems Ltd. All rights
reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form
or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written
permission of this company.
Trademarks
DIGISOLTM is a trademark of Smartlink Network Systems Ltd. All
other trademarks are the property of the respective
manufacturers.
Make sure that the package contains above items. If any of the
listed items is damaged or missing, please contact your retailer
immediately.
Note: Please verify the maximum power consumption of
your PoE enabled device before connecting to PoE injector
DG-PE2248D. If the PoE enabled device needs more than 16
watts of power then it can damage the DG-PE2248D.
Side View – Port Connectors
Following figure shows the side view of the product. There are
two Ethernet LAN ports. One is “Data IN” which connects as an
Uplink to your LAN switch. The other is “Data & Power Out”
which connects to PoE enabled device. It carries Power and Data
on a single Ethernet cable.
Introduction
Thank you for choosing Digisol DG-PE2248D Desktop Mount
48V DC Giga PoE injector. This PoE injector will supply steady
power to IEEE802.3af compliant network devices using Ethernet
Cable. PoE injector allows to use the existing Ethernet
infrastructure to transmit electrical power and data, to remote
network end points. This helps in reducing the cost of installation
of new power cables and saves time.
Hardware Installation
Step1: Connect one end of the power cord to the AC power outlet
and the other end to the Power connector on the device.
Key Features
• Complies with IEEE 802.3, IEEE 802.3u and IEEE802.3af
Standards.
•Transmits electrical power and data on the single Ethernet
Cable.
• Compatible with IEEE802.3af compliant devices.
• Integrated power module.
• Plug-and-Play installation.
• Compact Design.
Rev. 1.0 Copyright 2015 by Smartlink Network Systems Ltd. All rights reserved
DG-PE2248D Quick Installation Guide
Step2: Connect CAT5/5e/6 cable from LAN or a switch to “DataIn” port on DG-PE2248D.
DG-PE2248D Quick Installation Guide
DG-PE2248D Quick Installation Guide
Technical Specifications
Frequently Asked Questions
• Hardware Specifications
-One Power Connector
-One 10/100/1000 Mbps Ethernet Data In Port
-One 10/100/1000 Mbps Ethernet Power & Data Out Port (PoE)
Following are the solutions to problems that may occur during the
installation and operation of the Digisol DG-PE2248D PoE
injector.
1. The Power LED on DG-PE2248D is OFF.
• Standards Compliance
-IEEE802.3 10Base-T Ethernet
-IEEE802.3u 100Base-TX Fast Ethernet
-IEEE802.3ab 1000Base-T
-IEEE802.3af Power over Ethernet (PoE)
Step3: Connect CAT5/5e/6 cable from PoE enabled device (e.g.
PoE IP camera or a PoE Access point) to the “Data & Power Out”
port on DG-PE2248D.
• LED Indicator
- AC (Power), Port (PoE)
• Data Transfer rates
-100 Mbps Half-Duplex
-1000 Mbps Half-Duplex
• Network Cables
-100Base-Tx: UTP Cat5/5e (100m)
Your Installation is now complete
• Power
-Input: AC 100~ 240V, 50~ 60Hz
• Environmental Specifications
-Operating Temperature: 0º C to 40 º C
-Storage Temperature: -10 º C to 60 º C
-Operating Humidity: 10% ~ 90% RH, non-condensing
-Storage Humidity: 5%~90% RH, non-condensing
• Ensure that DG-PE2248D is connected to an AC
power outlet using the power cord shipped with the
product.
• Connect the power cord firmly to the power connector
on the device.
2. The PoE enabled device does not power on.
• Verify that the PoE device which needs to be powered
on is connected to the “Power & Data Out” port of DGPE2248D
• Ensure that the PoE device is connected firmly to DGPE2248D.
• Try using another CAT5/5e cable.
• Verify the Max. power consumption of the PoE enabled
device and also verify whether it complies with
IEEE802.3af standard.
3. Can DG-PE2248D work with any PoE enabled device?
• DG-PE2248D can power on any PoE enabled device
that complies with IEEE802.3af standard.
If you still encounter problems or have any questions regarding
the PoE injector Installation/Troubleshooting, please contact
DIGISOL Technical Assistance Center.
This product comes with one year warranty. For further details
about warranty policy and Product Registration, please visit
support section of www.digisol.com
Rev. 1.0 Copyright 2015 by Smartlink Network Systems Ltd. All rights reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising