HP BladeSystem p-Class SAN Connectivity Kit Quick Setup

HP BladeSystem p-Class SAN Connectivity Kit Quick Setup
Overview
HP BladeSystem
p-Class SAN
Connectivity Kit
Quick Setup Instructions
For Installing into Cisco Gigabit
Ethernet Switch Module
The HP BladeSystem p-Class SAN Connectivity Kit is an option
for the Cisco Gigabit Ethernet Switch Module for HP BladeSystem
p-Class, providing ProLiant BL servers with support for Fibre
Channel signal pass-through connectivity.
Kit Contents
• Two ProLiant BL p-Class OctalFC Interconnect Modules
• Two ProLiant BL p-Class Fibre Channel Signal Conditioning
Cards
• This installation card
• Limited Warranty and Material Limitations Documentation
Preparing for Installation
WARNING:
• Installation of the HP ProLiant BL p-Class OctalFC
Interconnect Modules and HP ProLiant BL p-Class Fibre
Channel Signal Conditioning Cards should be performed by
individuals who are both qualified in the servicing of
computer equipment and trained in the dangers associated
with products capable of producing hazardous energy levels.
• To reduce the risk of personal injury from hot surfaces, allow
the internal system components to cool before touching.
CAUTION: To prevent damage to the system, be aware of the
precautions you need to follow when setting up the system or
handling parts. A discharge of static electricity from a finger or
other conductor may damage system boards or other
static-sensitive devices. This type of damage may reduce the life
expectancy of the device.
Read instructions completely before beginning
installation procedure
© Copyright 2004 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should be
construed as constituting an additional warranty. HP shall not be liable for technical
or editorial errors or omissions contained herein.
HP BladeSystem p-Class SAN Connectivity Kit Quick Setup Instructions
First Edition (December 2004)
Part Number 380262-001
380262-001
To prevent electrostatic damage, observe the following
precautions:
• Avoid hand contact by transporting and storing products in
static-safe containers.
• Keep electrostatic-sensitive parts in their containers until they
arrive at static-free workstations.
• Place containers on a grounded surface before removing the
contents.
• Avoid touching pins, leads, or circuitry.
• Always be properly grounded when touching a static-sensitive
component or assembly.
Use one or more of the following methods when handling or
installing electrostatic-sensitive parts:
• Use a wrist strap connected by a ground cord to a grounded
workstation or computer chassis. Wrist straps are flexible
straps with a minimum of 1 megohm ±10 percent resistance in
the ground cords. To provide proper ground, wear the strap
snug against the skin.
• Use heel straps, toe straps, or boot straps at standing
workstations. Wear the straps on both feet when standing on
conductive floors or dissipating floor mats.
• Use conductive field service tools.
• Use a portable field service kit with a folding static-dissipating
work mat.
If you do not have any of the suggested equipment for proper
grounding, have an HP authorized reseller install the part.
Installation Guidelines
Observe the following guidelines during installation:
• Always install the OctalFC Interconnect Modules into the
top-left-most and top-right-most bays on the rear side of the
server blade enclosure.
• Install the Fibre Channel Signal Conditioning Cards into the
switch.
• Install the switch into the interconnect bays, which are the
left-most (side A) and right-most (side B) bays on the front side
of the server blade enclosure.
• Be sure that each interconnect module is fully seated. The
latch/handle will drop into place when the module is firmly
seated.
• Install the small form-factor pluggable optical transceivers
(SFP modules), that come with the Fibre Channel mezzanine
card for ProLiant BL servers, into the appropriate Fibre
Channel ports in the OctalFC Interconnect Module.
• You will need to provide optical cable with LC connectors to
connect to the transceiver SFP modules.
The following diagram illustrates the Fibre Channel signal
connectivity between server bays and the interconnect modules via
the backplane for p-Class server enclosures with enhanced
backplane components that support high-density blade servers.
The top and bottom server bays share the connections to the
ProLiant BL p-Class OctalFC Interconnect Modules.
Additional Information
For additional information about Storage Area Network (SAN)
connectivity, refer to the SAN Design Reference Guide located at
http://h18000.www1.hp.com/products/storageworks/san/documentation.html
Fibre Channel Signal Connectivity
The following diagram illustrates the Fibre Channel signal
connectivity between server bays and the interconnect modules via
the backplane for the p-Class server enclosure.
Upgrading CGESMs with a SAN
Connectivity Kit
CAUTION: Removing a CGESM from a powered enclosure will
result in the loss of network communications between the server
blade and the network infrastructure.
1. Remove the CGESM.
2.
3.
4.
5.
6.
7.
Remove the CGESM access panel.
Install the Fibre Channel Signal Conditioning Card.
Replace the CGESM access panel.
Install the OctalFC Interconnect Module.
Reinstall the CGESM.
Install SFP modules in Fibre Channel ports corresponding to
the ProLiant blade servers with Fibre Channel connectivity.
8. Install the SFP module into the port until it clicks (1).
9. Insert the optical cable into the SFP module (2).
10. When fully seated, both the SFP module and the cable click
into place.
OctalFC Interconnect Module LEDs
NOTE: The following LED assignments apply to servers in non-enhanced
backplane enclosures only. The LEDs are non-functional for p-Class server
enclosures with enhanced backplane components that support high-density
blade servers.
OctalFC Interconnect Module Ports
Item
Item
Backplane for p-Class
Server Enclosures
Backplane for p-Class Server
Enclosures with Enhanced
Backplane Components that
Support High-density Blades
1
Fibre Channel port for
server bay 1
Fibre Channel port for server
bay 1 and 9
2
Fibre Channel port for
server bay 2
Fibre Channel port for server
bay 2 and 10
3
Fibre Channel port for
server bay 3
Fibre Channel port for server
bay 3 and 11
4
Fibre Channel port for
server bay 4
Fibre Channel port for server
bay 4 and 12
5
Fibre Channel port for
server bay 5
Fibre Channel port for server
bay 5 and 13
6
Fibre Channel port for
server bay 6
Fibre Channel port for server
bay 6 and 14
7
Fibre Channel port for
server bay 7
Fibre Channel port for server
bay 7 and 15
8
Fibre Channel port for
server bay 8
Fibre Channel port for server
bay 8 and 16
Description
Status
1
LED for Fibre Channel port 1
Green = Link
Off = No Link
2
LED for Fibre Channel port 2
Green = Link
Off = No Link
3
LED for Fibre Channel port 3
Green = Link
Off = No Link
4
LED for Fibre Channel port 4
Green = Link
Off = No Link
5
LED for Fibre Channel port 5
Green = Link,
Off = No Link
6
LED for Fibre Channel port 6
Green = Link
Off = No Link
7
LED for Fibre Channel port 7
Green = Link
Off = No Link
8
LED for Fibre Channel port 8
Green = Link
Off = No Link
Regulatory Notice
European Union Notice
Products bearing the CE marking comply with the EMC Directive
(89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued
by the Commission of the European Community and if this product
has telecommunication functionality, the R&TTE Directive
(1999/5/EC). Compliance with these directives implies conformity
to the following European Norms (in parentheses are the
equivalent international standards and regulations):
• EN 55022 (CISPR 22) – Electromagnetic Interference
• EN55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11) – Electromagnetic
Immunity
• EN61000-3-2 (IEC61000-3-2) – Power Line Harmonics
• EN61000-3-3 (IEC61000-3-3) – Power Line Flicker
• EN 60950 (IEC 60950) – Product Safety
BSMI Notice
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising