Pro118 HDD Duplicator
Pro118
HDD Duplicator
User Guide V 1.0
Content
Chapter 1 - Product Introduction
1. Features ..........................................................................................................
2. Product Overview ..........................................................................................
3. Function Table ...............................................................................................
Chapter 2 - Function Introduction
1.
2.
3.
4.
5.
6.
Copy ...............................................................................................................
Compare .......................................................................................................
Copy & Compare .........................................................................................
Erase ...............................................................................................................
4.1 Quick Erase ..............................................................................................
4.2 Full Erase ...................................................................................................
4.3 DoD Erase ................................................................................................
4.4 DoD Erase Comp .....................................................................................
Utility ...............................................................................................................
5.1 Show HDD Info. ........................................................................................
5.2 Update System ........................................................................................
5.3 System Info. ..............................................................................................
Setup ................................................................................................................
6.1 Copy Area ................................................................................................
6.1.1 System and Files
6.1.2 All Partition
6.1.3 Whole HDD
6.2 Skip Error ...................................................................................................
6.3 Erase Master .............................................................................................
6.4 Unknown Format ......................................................................................
6.4.1 Copy unknown
6.4.2 Skip unknown
6.5 Transfer Rate ............................................................................................
6.6 Erase Pattern ............................................................................................
6.6.1 ONE Byte
6.6.2 4MB Byte
6.7 Language .................................................................................................
6.8 Restore Default ........................................................................................
Chapter 4. Specification
3
3
4
5
5
5
6
7
7
7
8
8
8
9
9
10
10
12
12
12
13
13
13
13
Specification .......................................................................................................... 14
2
Chapter 1 - Product Introduction
1. Features
●● High copy speed supports up to 90MB/second.
●● Auto power control to protects your HDD.(HDD only power on when
working)
●● Support 2.5" and 3.5" SATA HDD, IDE HDD and SSD.
●● Support 3 different duplicator mode; quick copy (System and files), All
partitions and Whole HDD.
●● Support Linux(Ext2/Ext3), NTFS, FAT quick copy mode copies only Data and
System area can highly increase the copy efficiency.
●● Support DoD standard erase function.
●● Auto detect and shows the bad sector quantity.
●● Light weight for easy carry(320g).
2. Product Overview
A. System Overview
Red : Fail
Green : Pass
Yellow : Powering
Target port
Source port
Backward
Forward
Confirm / OK
Cancel / Back
B. LCD Configuration
Target HDD Total size (Source)
Function
Time (mm:ss)
Copy progress %
Copied processed size (Target)
3
Chapter 1 - Product Introduction
3. Function Table
Function
Description
1. Copy
To copy source HDD to multiple target HDDs. Refer to function 6.Setup for 3 different copy
mode selection.
2. Compare
To compare data bit by bit between source and copied HDDs.
3. Copy+Compare
It makes copy first and then compare copied HDD with source HDD to ensure data
correctness.
4.1 Quick Erase
Erase HDD’s index table only, it takes short time to execute this function.
4. Erase
Note: Function 6.3 can select to
erase source HDD or not
4.2 Full Erase
Erase the whole HDD content.
4.3 DoD erase
Erase HDDs three times complying with USA Department of Defense (DoD) standard.
4.4 DoD EraseComp
Erase HDDs three times complying with n USA Department of Defense (DoD) standard
and bit by bit to check if data is completely erased.
5.1 Show HDD info
Shows HDD’s basic information such as HDD model name and capacity
5.2.1 Update BIOS
To update the system firmware via the HDD.
5. Utility 5.2 Update System
5.2.2 Format HDD
To format the HDD with a 2GB FAT partition in order to
quickly save firmware in the HDD.
5.3 System Info
This function will show information of the duplicator system, including controller model
number and software version.
6.1.1 System and files
Set to copy source HDD's data area only.
6.1 Copy Area
Setup copy mode.
6.1.2 ALL partition
Set to copy source HDD's all partitions.
6.1.3 Whole HDD
Set to copy the whole source HDD.
6.2 Skip Error
Set to ignore error of source HDD while copying. (0 -100 Set to ignore error of source HDD.)
6.3 Erase Master
Setup to erase source HDD or
not.
6. Setup
6.4 Unknown Format 6.3.1 Disable
Disable erase source HDD.
6.3.2 Enable
Enable erase source HDD.
6.4.1 Copy unknown
Copy unknown area when the device can not identify
the format.
6.4.2 Skip unknown
Skip copy unknown area when the device can not
identify the format.
6.5 Transfer Rate
Select the proper transfer rate UDMA2-7. 7 is the fastest.
6.6.1 ONE Byte
A random character to be written into every byte.
6.6 Erase Pattern
6.6.2 4MB Byte
A set of random character to be written into a set of
area.
6.7 Language
English / Japanese
6.8 Restore Default
Back to original manufacturer setting.
4
Chapter 2 - Function Introduction
1. Copy
It copies data from source HDD to target HDD. Please make sure you have
choose correct copy mode you like to use, about the three copy modes please
refer to function [6.1 Copy Area] for details.
The default setting is "System and Files".
2. Compare
It is used to check if the data on source HDD is identical to target HDD after
duplication.
3. Copy & Compare
It makes copy first and then compare copied HDD with source HDD to ensure
data correctness.
Before copy, there are two setups to be reminded:
a. Shows the quantity of bad sector in Source and Target HDDs.
Copy Process
Total data capacity
Copied data capacity
Copied Time
Copy Process
(if there is any bad sector)
Source bad sector
Target bad sector
Copied Time
Copy Process
5
Chapter 2 - Function Introduction
Copy result:
(Pass)
(Fail)
Total copy Time
Target bad sector
Source bad sector
The default setting of error counter is 0. If you like to increase the
accepted error sectors of the HDD, you can use function 6.2 to setup
"skip error".
b. Select the suitable copy mode by function 6.1 Copy Area, the Default
setting is quick copy mode "System and Files".
The special features of quick copy System and Files:
●● Using this copy mode, the system will analyze the source's copy
data area only, and only copy data and system file of the HDD.
There is no need to copy rest of empty space.
●● This function only support FAT, NTFS and Linux (Ext2and Ext3)
●● It is strongly suggested to use the same capacity of source and
target HDD.
4. Erase
Please choose the appropriate erase method when you like to dispose or
re-use the HDDs.
Function 6.3 Erase Master is to determine erase source HDD or not.
The default setting is "Disable erase source HDD".
The function can be stopped while processing by pressing [ESC] for
about 3~4 seconds.
6
Chapter 2 - Function Introduction
4.1 Quick Erase
The function will ONLY erase the index of the HDD. It is the quickest way to erase
HDD. It will damage the data in HDD, please make sure you have backup all
important data before using this function.
4.2 Full Erase
The function will erase the whole sectors on the target HDD. It will take longer
time than quick erase. It will damage the data in HDD, please make sure you
have backup all important data before using this function.
4.3 DoD Erase
This is to comply with the U.S.A. Department of Defense (DoD 5220) standard
to fully erase the HDD three times bit by bit to rewrite HDD to guarantee the
data was deleted. It will damage the data in HDD, please make sure you have
backup all important data before using this function.
Steps of Erase:
① Showing how many HDD are ready, press
to start.
② Erasing.
③ Shows the result when finish.
7
Chapter 2 - Function Introduction
4.4 DoD Erase Comp
Besides DoD erase, this function will also execute compare function to make
sure the random bit was correctly written. This way of erase is to erase HDD over
each sector three times: the first time with zeros (0x00), second time with 0xFF
and the third time with random characters. There is one final pass to compare
random characters by reading. It will damage the data in HDD, please make
sure you have backup all important data before using this function.
5. Utility
5.1 Show HDD Info.
This function will show HDD's basic information such as HDD capacity and model
number.
Steps of Show HDD Info.:
① Select function.
② Shows HDD information.
Port No.
HDD model
number
8
HDD capacity
Chapter 2 - Function Introduction
5.2 Update System
You can follow the steps to update system firmware:
① Select Function 5.2.2
② Download the BIOS from PC to your HDD.
HDD
USB
HDD Enclosure
PC
The purpose of this is because 2GB FAt HDD Partition can speed up
update process.
Format HDD
③ Plug in HDD into duplicator, select function 5.2.1 to update BIOS.
5.3 System Info.
This function shows information of the duplicator includes model name and
firmware version.
BIOS version
9
Chapter 2 - Function Introduction
6. Setup
6.1 Copy Area
6.1.1 System and Files
It will copy source HDD's System and Files instead of the whole HDD. The system
will analyze the source HDD and identify the data area to copy. As long as the
source HDD's data within the target HDD's space, the copy will be processed. System and Files only supports FAT, NTFS and EXT2 / EXT3 for quick
copy.
6.1.2 All Partition
This mode will bit by bit copy all of the partitions no matter there is data exist or
not. The capacity of target HDD has to be bigger than the partition required
capacity.
10
Chapter 2 - Function Introduction
6.1.3 Whole HDD
It is to copy the whole source HDD, no matter of the content, format, partition or
empty space. This mode will take much more time to duplicate the source HDD
completely.
After copy, the remaining space in the copied HDD can be used by
PC for further partitioning.
11
Chapter 2 - Function Introduction
6.2 Skip Error
This function sets the number of error you like to skip during copy process.
If the HDD is very critical for content correctness, it is strongly
recommended to keep the Skip Error to be "0".
6.3 Erase Master
It is set to allow erase source HDD or not. Please make sure this setting before
you execute erase function.
6.4 Unknown Format
This function allows you to select if you want to copy the unknown format area.
6.4.1 Copy unknown
Copy all the unknown area if device can not identify the format during copy.
6.4.2 Skip unknown
Skip the unknown area if device can not identify the format during copy.
12
Chapter 2 - Function Introduction
6.5 Transfer Rate
You can select the best transfer rate from UDMA 2 to UDMA7 for your HDD
duplication progress. If you are not confident on the HDD quality or you find
a high failure rate on copy or compare. It is recommended to slow down the
UDMA mode.
6.6 Erase Pattern
Select different erase method.
6.6.1 ONE Byte
A random character to be written into every byte.
6.6.2 4MB Byte
A set of random character to be written into a set of area.
6.7 Language
English and Japanese are available for selection.
6.8 Restore Default
Select and go back to the manufacturer's default setting.
13
Chapter 3. Specification
Product Name
Carry Mini HDD Dupe Product Number
PRO-118
Targets
1:1
HDD Interface
SATA, IDE(optional)
Display
Monochrome LCD
Control Button
4 push buttons
Compatible HDD
All major brand of 2.5”,3.5” SATA and IDE HDD and SATA SSD
Duplication Mode
1. System and Files / 2. All Partition / 3. Whole HDD
Support Formate
Supports all formate, Quick copy (System and Files) supports FAT, NTFS, Linux
(Ext.2 /Ext.3).
Capacity
up to 2TB
Power Supply
12V, 3A
Storage
5˚C~45˚C
Working
-20˚C~85˚C
Storage
20%~80%
Working
5%~95%
Temperature
Humidity
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising