installation instructions gt7017e 5 shelf unit, resin – wall mount

INSTALLATION INSTRUCTIONS
GT7017E 5 SHELF UNIT, RESIN – WALL MOUNT
CARTON CONTENTS
QUANTITY
CARTON #1
1
20
4
CARTON #2
1
20
DESCRIPTION
SHELF COMPONENTS (SEE PG 2)
#8 X 1” SELF DRILLING SCREWS
#6 X 1” SHARP POINT SCREWS
CRADLE COMPONENTS & TOP BRACKET
NUTS / BOLTS / WASHERS
TOOLS REQUIRED
ELECTRIC DRIVER OR DRILL
PHILLIPS DRIVER BIT
SMALL ADJUSTABLE WRENCH OR PILERS
1/16” DIA DRILL BIT (OPTIONAL)
HAMMER OR RUBBER MALLET
TAPE MEASURE / SAFETY GLASSES
PG 1
QUESTIONS ???? CALL 1-866 664 2724
REV 0, 09/13
5 SHELF UNIT, RESIN – WALL MOUNT ASSEMBLY INSTRUCTIONS
STEP #1
LAYOUT FROM THE SHELF CARTON AND CHECK THE PARTS RECEIVED. THERE ARE 4 EXTRA TOP CAPS AND
4 EXTRA BOTTOM CAPS SUPPLIED BUT NOT REQUIRED FOR THIS ASSEMBLY. YOU CAN DISCARD THESE
EXTRA ITEMS.
STEP #2
A. ON THE BOTTOM OF QTY 1, SHELF, PRESS QTY 4 OF THE BOTTOM CAPS INTO THE POST HOLES.
STEP #3
A. ORIENTATE QTY 1, SHELF WITH THE CURVED EDGE AS SHOWN. PRESS QTY 4, POST INTO THE SHELF POST
HOLES. USE A RUBBER MALLET TO FIRMLY SEAT INTO THE HOLES IF NEEDED.
B. ORIENTATE QTY 1, ANOTHER SHELF WITH THE CURVED EDGE FACING MATCHING THE FIRST SHELF AND
PRESS THE POSTS INTO THE BOTTOM HOLES OF THE SHELF. AGAIN, USE A RUBBER MALLET / HAMMER TO
FIRMLY SEAT.
PG 2
QUESTIONS ???? CALL 1-866 664 2724
REV 0, 09/13
5 SHELF UNIT, RESIN – WALL MOUNT ASSEMBLY INSTRUCTIONS
STEP #4
A. CONTINUE REPEATING STEP #3 UNTIL YOU HAVE ALL FIVE SHELVES ASSEMBLED.
B. PRESS QTY 4, OF THE TOP END CAPS INTO THE REMAINING POST HOLES.
STEP #5
A. CHECK THAT ALL THE POSTS / SHELVES ARE FULLY ENGAGED AND SEATED.
B. USING THE QTY 20, SCREWS SUPPLIED, FASTEN THEM AS SHOWN IN THE IMAGES BELOW. USE THE 1/16”
DIA DRILL TO MAKE PILOT HOLES IF DESIRED. INSTALLING THESE SCREWS WILL MAKE THE SHELVING UNIT A
VERY RIGID FINAL ASSEMBLY.
STEP #6
PRESS THE BUBBLE LOGO ON THE TOP RIGHT SHELF CORNER AS SHOWN.
PG 3
QUESTIONS ???? CALL 1-866 664 2724
REV 0, 09/13
5 SHELF UNIT, RESIN – WALL MOUNT ASSEMBLY INSTRUCTIONS
STEP #7
REMOVE THE BRACKET SHOWN BELOW FROM THE CRADLE CARTON (MARKED WITH P/N GT101) AND FASTEN
THIS BRACKET TO THE BACK OF THE SHELF ASSEMBLY (REMEMBER THE “BACK” IS OPPOSITE TO THE
CURVED FRONT SHOWN IN STEP 3A ABOVE).
FASTEN THE BRACKET WITH THE 4 SCREWS SUPPLIED. YOU MAY WANT TO PREDRILL THE SCREW HOLES
WITH A 1/16” DRILL BIT AS SHOWN.
STEP #8
LAYOUT THE REMAINING COMPONENTS OF THE CRADLE CARTON AND CHECK THE PARTS RECEIVED.
ASSEMBLE THE CRADLE AS SHOWNON THE NEXT PAGE, BUT DO NOT FULLY TIGHTEN THE FASTENERS IN
THE SIDE PANEL SLOTS. ALLOW THE SIDE PANELS TO MOVE UP/ DOWN IN THE SLOT(S).
PG 4
QUESTIONS ???? CALL 1-866 664 2724
REV 0, 09/1
5 SHELF UNIT, RESIN – WALL MOUNT ASSEMBLY INSTRUCTIONS
PG 5
QUESTIONS ???? CALL 1-866 664 2724
REV 0, 09/13
5 SHELF UNIT, RESIN – WALL MOUNT ASSEMBLY INSTRUCTIONS
STEP # 9
MEASURE THE HEIGHT OF THE SHELF ASSEMBLY. MEASURE DOWN FROM WHERE YOU WANT TO INSTALL THE
SHELF ASSEMBLY IN THE TEKPANEL AND SLIP THE CRADLE INTO THE WALL SLOTS.
STEP #10
RAISE THE CRADLE SIDE TO THE MEASURED DIMENSION OF THE SHELF UNIT AND TIGHTEN THE 4 NUTS/
BOLTS, WASHERS AND STAR WASHERS ON THE SIDE PANELS OF THE CRADLE. (THE STAR WASHERS ARE
CRITICAL BECAUSE THEY “LOCK” THE SIDE PANELS IN PLACE.)
PG 6
QUESTIONS ???? CALL 1-866 664 2724
REV 0, 09/13
5 SHELF UNIT, RESIN – WALL MOUNT ASSEMBLY INSTRUCTIONS
STEP #11
TILTING THE SHELF ASSEMBLY FORWARD, PLACE THE TOP BRACKET INTO THE PREVIOUSLY SELECTED
TEKPANEL SLOT AND SWING IT INTO THE CRADLE AS SHOWN.
IF YOU HAVE BEEN CAREFUL IN YOUR MEASUREMENTS, THE SHELF ASSEMBLY SHOULD BE LOCKED INTO
PLACE AND FULLY SUPPORTED BY THE CRADLE.
IF THERE IS SPACE BETWEEN THE CRADLE BOTTOM AND SHELF UNIT BOTTOM, READJUST THE CRADLE
BOTTOM UP UNTIL IT FULLY SUPPORTS THE SHELVING UNIT.
THE ENTIRE SHELVING UNIT CAN BE EASILY MOVED BY REVERSING THE ABOVE STEPS.
PG 7
QUESTIONS ???? CALL 1-866 664 2724
REV 0, 09/13

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project